drivers/char/tpm/tpm_tis.c:838: warning: ‘tpm_tis_resume’ defined but
not used
Reported-by: James Morris <jmorris@namei.org>
Fixes: 00194826e6 ("tpm_tis: Clean up the force=1 module parameter")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
cc: stable@vger.kernel.org
Display fps on demand for each used plane:
cat /sys/kernel/debug/dri/0/fps_get
Display fps in live in the console for each used plane:
echo 255 > /sys/kernel/debug/dri/0/fps_show
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Configures the framer of the HDMI connection.
By default starts in HDMI mode and can be swtich to DVI.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Make the value of the colorspace of the HDMI infoframe configurable.
HDMI colorspace could be: RGB, YUV422 or YUV444
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Vendor specific infoframe is mandatory for 4K2K resolution.
Without this, the HDMI protocol compliance fails.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Clear all infoframe registers when the HDMI link is stopped.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Set the infoframe transmission mode according to the type of
the infoframe.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Make sure the HD DACS are disabled when the HDA connector
is created.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Modify AWG algorithm in order to handle more than 1023 lines
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>
Modify delay to display last pixel column on DVO
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>
The DVO connector is tag as disconnect because of a wrong management
of the panel detection.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Disable the clipping mode for hdmi, dvo and hda connectors.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Use BT601 for SD/ED resolution and BT709 for HD resolution
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Atomic update should never fail. Thus all checks must be done in
the atomic_check function for each plane (gdp, hqvdp and cursor).
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
It may happen that the cursor is displayed with wrong colors which can
be explained by a CLUT wrongly fetched at the first display.
Fetching the CLUT at each commit (=move) ensures that the right colors
are used, at least from the first cursor move.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>
GDP source width should be equal to the destination width to get
rid of this issue.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
When a GDP gets a scale request (which it does not support), it accepts it
but crops or clamps and outputs a warning message.
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>
Only RGB formats supported by GDP planes
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>
When a frame or a field is skipped, output a Warning message instead of
an Error message.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>
data_en is a local variable that doesn't need to be set as
awg_generate_instr can be called directly with the requested value.
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>
This update eases to understand the VTG programming.
It also sets a VTG output id for each supported connectors.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
sti now support of atomic modesetting so set the flag to enable it.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>
Set CRTC modesetting parameters to avoid warnings in atomic mode.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>
In some cases last_close() could be called before sti_gdp_disable()
and make kernel crash because mixer structure has been destroy.
Let's gdp keep a reference on vtg to fix that (like it is already done
in HQVDP)
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>
This patch fixes the return value in a case which should never occur.
Instead returning "-EINVAL" we return LOWPAN_IPHC_DAM_00 which is
invalid on context based addresses. Also change the WARN_ON_ONCE to
WARN_ONCE which was suggested by Dan Carpenter.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently the interrupt handler of HD-audio driver assumes that no irq
update is needed while processing the irq. But in reality, it has
been confirmed that the HW irq is issued even during the irq
handling. Since we clear the irq status at the beginning, process the
interrupt, then exits from the handler, the lately issued interrupt is
left untouched without being properly processed.
This patch changes the interrupt handler code to loop over the
check-and-process. The handler tries repeatedly as long as the IRQ
status are turned on, and either stream or CORB/RIRB is handled.
For checking the stream handling, snd_hdac_bus_handle_stream_irq()
returns a value indicating the stream indices bits. Other than that,
the change is only in the irq handler itself.
Reported-by: Libin Yang <libin.yang@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Simply document new compatibility string.
As a previous patch adds a generic R-Car Gen2 compatibility string
there appears to be no need for a driver updates.
By documenting these compat stings they may be used in DTSs shipped, for
example as part of ROMs. They must be used in conjunction with the Gen2
fallback compat string. At this time there are no known differences between
the r8a779[234] IP blocks and that implemented by the driver for the Gen2
fallback compat string. Thus there is no need to update the driver as the
use of the Gen2 fallback compat string will activate the correct code in
the current driver while leaving the option for r8a779[234]-specific driver
code to be activated in an updated driver should the need arise.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add fallback compatibility string for R-Car Gen 1 and Gen2.
In the case of Renesas R-Car hardware we know that there are generations of
SoCs, e.g. Gen 1 and Gen 2. But beyond that its not clear what the
relationship between IP blocks might be. For example, I believe that
r8a7779 is older than r8a7778 but that doesn't imply that the latter is a
descendant of the former or vice versa.
We can, however, by examining the documentation and behaviour of the
hardware at run-time observe that the current driver implementation appears
to be compatible with the IP blocks on SoCs within a given generation.
For the above reasons and convenience when enabling new SoCs a
per-generation fallback compatibility string scheme being adopted for
drivers for Renesas SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes the coding style issues introduced in commit:
90cfde4658 can: ems_usb: Fix possible tx overflow
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
gs_destroy_candev() erroneously calls kfree() on a struct gs_can *, which is
allocated through alloc_candev() and should instead be freed using
free_candev() alone.
The inappropriate use of kfree() causes the kernel to hang when
gs_destroy_candev() is called.
Only the struct gs_usb * which is allocated through kzalloc() should be freed
using kfree() when the device is disconnected.
Signed-off-by: Maximilian Schneider <max@schneidersoft.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch removes unnecessary return variables and compresses the
return logic.
The coccinelle script that finds and fixes this issue is:
@@ type T; identifier i,f; constant C; @@
- T i;
...when != i
when strict
( return -C;
|
- i =
+ return
f(...);
- return i;
)
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unnecessary dev_set_drvdata() has been removed since the driver
core clears the driver data to NULL after device release or on
probe failure. There is no need to manually clear the device
driver data to NULL.
The Coccinelle semantic patch used to make this change is as follows:
//<smpl>
@@
struct device *dev;
@@
- dev_set_drvdata(dev, NULL);
//</smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pfn field in the channel is 64 bits, the parameter being passed
should be 64 bits as well.
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Smatch complained about inconsistent indenting. This patch addresses it.
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The other error paths return meaningful error codes, except for the one
when registering a device, which just returned -1. Let's return ENODEV
when it fails to register instead.
Signed-off-by: Benjamin Romer <benjamin.romer@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify this function by removing the goto in favor of handling errors
immediately. Eliminate the vaguely-named variable x, and remove the
unneeded initialization of rc. Lastly, provide meaningful error values
to the callback function instead of just passing back a -1 for failure.
Signed-off-by: Benjamin Romer <benjamin.romer@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
