If CONFIG_BITREVERSE is not built-in, the sht15 driver fails to link:
drivers/built-in.o: In function `sht15_crc8':
drivers/hwmon/sht15.c:195: undefined reference to `byte_rev_table'
This adds a Kconfig 'select' statement, like all other users of
bitrev.h have it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 33836ee985 ("hwmon:change sht15_reverse()")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
As reported by smatch:
drivers/media/pci/cx23885/cx23885-dvb.c:2174 dvb_register() info: 'a8293_pdata' is not actually initialized (unreached code).
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/v4l2-core/videobuf2-core.c:2415 __vb2_init_fileio() warn: possible memory leak of 'fileio'
While here, avoid the usage of sizeof(struct foo_struct).
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Limit busywaiting only to the request currently being processed by the
GPU. If the request is not currently being processed by the GPU, there
is a very low likelihood of it being completed within the 2 microsecond
spin timeout and so we will just be wasting CPU cycles.
v2: Check for logical inversion when rebasing - we were incorrectly
checking for this request being active, and instead busywaiting for
when the GPU was not yet processing the request of interest.
v3: Try another colour for the seqno names.
v4: Another colour for the function names.
v5: Remove the forced coherency when checking for the active request. On
reflection and plenty of recent experimentation, the issue is not a
cache coherency problem - but an irq/seqno ordering problem (timing issue).
Here, we do not need the w/a to force ordering of the read with an
interrupt.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: "Rogozhkin, Dmitry V" <dmitry.v.rogozhkin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Eero Tamminen <eero.t.tamminen@intel.com>
Cc: "Rantala, Valtteri" <valtteri.rantala@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449833608-22125-4-git-send-email-chris@chris-wilson.co.uk
When waiting for high frequency requests, the finite amount of time
required to set up the irq and wait upon it limits the response rate. By
busywaiting on the request completion for a short while we can service
the high frequency waits as quick as possible. However, if it is a slow
request, we want to sleep as quickly as possible. The tradeoff between
waiting and sleeping is roughly the time it takes to sleep on a request,
on the order of a microsecond. Based on measurements of synchronous
workloads from across big core and little atom, I have set the limit for
busywaiting as 10 microseconds. In most of the synchronous cases, we can
reduce the limit down to as little as 2 miscroseconds, but that leaves
quite a few test cases regressing by factors of 3 and more.
The code currently uses the jiffie clock, but that is far too coarse (on
the order of 10 milliseconds) and results in poor interactivity as the
CPU ends up being hogged by slow requests. To get microsecond resolution
we need to use a high resolution timer. The cheapest of which is polling
local_clock(), but that is only valid on the same CPU. If we switch CPUs
because the task was preempted, we can also use that as an indicator that
the system is too busy to waste cycles on spinning and we should sleep
instead.
__i915_spin_request was introduced in
commit 2def4ad99b [v4.2]
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Apr 7 16:20:41 2015 +0100
drm/i915: Optimistically spin for the request completion
v2: Drop full u64 for unsigned long - the timer is 32bit wraparound safe,
so we can use native register sizes on smaller architectures. Mention
the approximate microseconds units for elapsed time and add some extra
comments describing the reason for busywaiting.
v3: Raise the limit to 10us
v4: Now 5us.
Reported-by: Jens Axboe <axboe@kernel.dk>
Link: https://lkml.org/lkml/2015/11/12/621
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: "Rogozhkin, Dmitry V" <dmitry.v.rogozhkin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Eero Tamminen <eero.t.tamminen@intel.com>
Cc: "Rantala, Valtteri" <valtteri.rantala@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449833608-22125-3-git-send-email-chris@chris-wilson.co.uk
The busywait in __i915_spin_request() does not respect pending signals
and so may consume the entire timeslice for the task instead of
returning to userspace to handle the signal.
In the worst case this could cause a delay in signal processing of 20ms,
which would be a noticeable jitter in cursor tracking. If a higher
resolution signal was being used, for example to provide fairness of a
server timeslices between clients, we could expect to detect some
unfairness between clients (i.e. some windows not updating as fast as
others). This issue was noticed when inspecting a report of poor
interactivity resulting from excessively high __i915_spin_request usage.
Fixes regression from
commit 2def4ad99b [v4.2]
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Apr 7 16:20:41 2015 +0100
drm/i915: Optimistically spin for the request completion
v2: Try to assess the impact of the bug
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc; "Rogozhkin, Dmitry V" <dmitry.v.rogozhkin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Eero Tamminen <eero.t.tamminen@intel.com>
Cc: "Rantala, Valtteri" <valtteri.rantala@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449833608-22125-2-git-send-email-chris@chris-wilson.co.uk
The realview multiplatform series has a trivial conflict with
one of the treewide cleanups, let's just merge that in to
avoid having to resolve this later.
* treewide/cleanup:
ARM: use "depends on" for SoC configs instead of "if" after prompt
ARM/clocksource: use automatic DT probing for ux500 PRCMU
ARM: use const and __initconst for smp_operations
ARM: hisi: do not export smp_operations structures
Conflicts:
arch/arm/mach-integrator/Kconfig
The handling of q->plane_sizes was wrong in vb2_core_create_bufs().
The q->plane_sizes array was global and it was overwritten by create_bufs.
So if reqbufs was called with e.g. size 100000 then q->plane_sizes[0] would
be set to 100000. If create_bufs was called afterwards with size 200000,
then q->plane_sizes[0] would be overwritten with the new value. Calling
create_bufs again for size 100000 would cause an error since 100000 is now
less than q->plane_sizes[0].
This patch fixes this problem by 1) removing q->plane_sizes and using the
vb->planes[].length field instead, and 2) by introducing a min_length field
in struct vb2_plane. This field is set to the plane size as returned by
the queue_setup op and is the minimum required plane size. So user pointers
or dmabufs should all be at least this size.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Ensure that the offsets are correct before buf_init() is called.
As a consequence the __setup_offsets() function now sets up the
offsets for the given buffer instead of for all new buffers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The platsmp-dt.c file does not build when CONFIG_SMP is disabled:
platsmp-dt.c:84:2: error: unknown field 'smp_prepare_cpus' specified in initializer
This changes the Makefile to build it conditionally on CONFIG_SMP.
The legacy platsmp.c file is only used for ATAGS based builds, so
we can move it into the CONFIG_ATAGS conditional.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fill in q->bufs[vb->index] before the call to buf_init: it makes
sense that this is initialized correctly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Rather than setting up the lengths at the end, set them up when
the vb2_buffer is allocated. This also ensures that buf_init()
sees the right length values.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This ops can never fail, so make these void functions.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This module is no longer V4L2 specific, so update the module description
accordingly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
After several open/close sai test with ctrl+c, there will be
I/O error. The SAI can't work anymore, can't recover. There
will be no frame clock. With adding the software reset in
trigger stop, the issue can be fixed.
This is a hardware bug/errata and reset is the only option.
According to the reference manual, the software reset doesn't
reset any control register but only internal hardware logics
such as bit clock generator, status flags, and FIFO pointers.
(Our purpose is just to reset the clock generator while the
software reset is the only way to do that.)
Since slave mode doesn't use the clock generator, only apply
the reset procedure to the master mode.
For asynchronous mode, TX will not be reset when RX is still
running. In this case, i can't reproduce this issue.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move things related with vb2 file I/O and vb2_thread without doing any
functional changes. After that, videobuf2-internal.h is removed because
it is not necessary any more.
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace v4l2-stuffs with common things in struct vb2_fileio_data and
vb2_thread().
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The location in which last_buffer_queued is set is moved to fill_v4l2_buffer().
So, __vb2_perform_fileio() can use vb2_core_dqbuf() instead of
vb2_internal_dqbuf().
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add copy_timestamp to struct vb2_queue as a flag set if vb2-core should
copy timestamps.
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that we have multiplatform support, let the RealView
defconfigs select all the RealView boards so we boot out of
the box like before. This updates both defconfigs.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Move timestamp from struct vb2_v4l2_buffer to struct vb2_buffer
for common use, and change its type to u64 in order to handling
y2038 problem. This patch also includes all device drivers' changes related to
this restructuring.
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The timestamp of a v4l2_buffer was advertised as being CLOCK_MONOTONIC,
but instead a timestamp from a header field was used. This is inconsistent
and not what applications expect. Use v4l2_get_timestamp to properly
set the timestamp.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
During the Seoul media workshop we decided to relax the VIDIOC_CREATE_BUFS
specification so it would no longer require drivers to validate the format
field since almost no driver did that anyway.
Instead drivers use the buffer size(s) based on the format type and the
corresponding format fields and will ignore any other fields. If the size
cannot be used an error is returned, otherwise the size is used as-is.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
commit f598282f51 ("PCI: Fix the NIU MSI-X problem in a better way")
teaches us that dealing with MSI-X can be troublesome.
Further checks in the MSI-X architecture shows that if the
PCI_COMMAND_MEMORY bit is turned of in the PCI_COMMAND we
may not be able to access the BAR (since they are memory regions).
Since the MSI-X tables are located in there.. that can lead
to us causing PCIe errors. Inhibit us performing any
operation on the MSI-X unless the MEMORY bit is set.
Note that Xen hypervisor with:
"x86/MSI-X: access MSI-X table only after having enabled MSI-X"
will return:
xen_pciback: 0000:0a:00.1: error -6 enabling MSI-X for guest 3!
When the generic MSI code tries to setup the PIRQ without
MEMORY bit set. Which means with later versions of Xen
(4.6) this patch is not neccessary.
This is part of XSA-157
CC: stable@vger.kernel.org
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Otherwise just continue on, returning the same values as
previously (return of 0, and op->result has the PIRQ value).
This does not change the behavior of XEN_PCI_OP_disable_msi[|x].
The pci_disable_msi or pci_disable_msix have the checks for
msi_enabled or msix_enabled so they will error out immediately.
However the guest can still call these operations and cause
us to disable the 'ack_intr'. That means the backend IRQ handler
for the legacy interrupt will not respond to interrupts anymore.
This will lead to (if the device is causing an interrupt storm)
for the Linux generic code to disable the interrupt line.
Naturally this will only happen if the device in question
is plugged in on the motherboard on shared level interrupt GSI.
This is part of XSA-157
CC: stable@vger.kernel.org
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Otherwise an guest can subvert the generic MSI code to trigger
an BUG_ON condition during MSI interrupt freeing:
for (i = 0; i < entry->nvec_used; i++)
BUG_ON(irq_has_action(entry->irq + i));
Xen PCI backed installs an IRQ handler (request_irq) for
the dev->irq whenever the guest writes PCI_COMMAND_MEMORY
(or PCI_COMMAND_IO) to the PCI_COMMAND register. This is
done in case the device has legacy interrupts the GSI line
is shared by the backend devices.
To subvert the backend the guest needs to make the backend
to change the dev->irq from the GSI to the MSI interrupt line,
make the backend allocate an interrupt handler, and then command
the backend to free the MSI interrupt and hit the BUG_ON.
Since the backend only calls 'request_irq' when the guest
writes to the PCI_COMMAND register the guest needs to call
XEN_PCI_OP_enable_msi before any other operation. This will
cause the generic MSI code to setup an MSI entry and
populate dev->irq with the new PIRQ value.
Then the guest can write to PCI_COMMAND PCI_COMMAND_MEMORY
and cause the backend to setup an IRQ handler for dev->irq
(which instead of the GSI value has the MSI pirq). See
'xen_pcibk_control_isr'.
Then the guest disables the MSI: XEN_PCI_OP_disable_msi
which ends up triggering the BUG_ON condition in 'free_msi_irqs'
as there is an IRQ handler for the entry->irq (dev->irq).
Note that this cannot be done using MSI-X as the generic
code does not over-write dev->irq with the MSI-X PIRQ values.
The patch inhibits setting up the IRQ handler if MSI or
MSI-X (for symmetry reasons) code had been called successfully.
P.S.
Xen PCIBack when it sets up the device for the guest consumption
ends up writting 0 to the PCI_COMMAND (see xen_pcibk_reset_device).
XSA-120 addendum patch removed that - however when upstreaming said
addendum we found that it caused issues with qemu upstream. That
has now been fixed in qemu upstream.
This is part of XSA-157
CC: stable@vger.kernel.org
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The guest sequence of:
a) XEN_PCI_OP_enable_msix
b) XEN_PCI_OP_enable_msix
results in hitting an NULL pointer due to using freed pointers.
The device passed in the guest MUST have MSI-X capability.
The a) constructs and SysFS representation of MSI and MSI groups.
The b) adds a second set of them but adding in to SysFS fails (duplicate entry).
'populate_msi_sysfs' frees the newly allocated msi_irq_groups (note that
in a) pdev->msi_irq_groups is still set) and also free's ALL of the
MSI-X entries of the device (the ones allocated in step a) and b)).
The unwind code: 'free_msi_irqs' deletes all the entries and tries to
delete the pdev->msi_irq_groups (which hasn't been set to NULL).
However the pointers in the SysFS are already freed and we hit an
NULL pointer further on when 'strlen' is attempted on a freed pointer.
The patch adds a simple check in the XEN_PCI_OP_enable_msix to guard
against that. The check for msi_enabled is not stricly neccessary.
This is part of XSA-157
CC: stable@vger.kernel.org
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The queue_setup callback has a void pointer that is just for V4L2
and is the pointer to the v4l2_format struct that was passed to
VIDIOC_CREATE_BUFS. The idea was that drivers would use the information
from that struct to buffers suitable for the requested format.
After the vb2 split series this pointer is now a void pointer,
which is ugly, and the reality is that all existing drivers will
effectively just look at the sizeimage field of v4l2_format.
To make this more generic the queue_setup callback is changed:
the void pointer is dropped, instead if the *num_planes argument
is 0, then use the current format size, if it is non-zero, then
it contains the number of requested planes and the sizes array
contains the requested sizes. If either is unsupported, then return
-EINVAL, otherwise use the requested size(s).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The guest sequence of:
a) XEN_PCI_OP_enable_msi
b) XEN_PCI_OP_enable_msi
c) XEN_PCI_OP_disable_msi
results in hitting an BUG_ON condition in the msi.c code.
The MSI code uses an dev->msi_list to which it adds MSI entries.
Under the above conditions an BUG_ON() can be hit. The device
passed in the guest MUST have MSI capability.
The a) adds the entry to the dev->msi_list and sets msi_enabled.
The b) adds a second entry but adding in to SysFS fails (duplicate entry)
and deletes all of the entries from msi_list and returns (with msi_enabled
is still set). c) pci_disable_msi passes the msi_enabled checks and hits:
BUG_ON(list_empty(dev_to_msi_list(&dev->dev)));
and blows up.
The patch adds a simple check in the XEN_PCI_OP_enable_msi to guard
against that. The check for msix_enabled is not stricly neccessary.
This is part of XSA-157.
CC: stable@vger.kernel.org
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
- Tested on the ARM PB11MPCore
- Tested with boardfile boot
- Tested with DeviceTree boot
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tfk1
-----END PGP SIGNATURE-----
Merge tag 'realview-multiplatform-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/multiplatform
Pull "Multiplatform support for the RealView" from Linus Walleij:
Here is the result of my application of the second part of Arnds
patchset, actually enabling multiplatform and getting the RealView
off the ground as a multiplatform target.
It is dependent on an outstanding patch to the irqchips tree bumping
the number of GICs to 2 for the RealView platform. I cannot say I will
be sleepless if these go in side by side: each branch will compile but
will not boot until both trees have been pulled hurting bisectability a
bit.
- Tested on the ARM PB11MPCore
- Tested with boardfile boot
- Tested with DeviceTree boot
* tag 'realview-multiplatform-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: realview: select apropriate targets
ARM: realview: clean up header files
ARM: realview: make all header files local
ARM: no longer make CPU targets visible separately
ARM: integrator: use explicit core module options
ARM: realview: enable multiplatform
The VID_A_GPCNT register is for video, not vbi. Read from the right
register and don't write to the video register.
Based upon Devin's initial patch made for an older kernel which I
cleaned up and rebased. Thanks to Kernel Labs for that work.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for these two new cards.
Based upon Devin's initial patch made for an older kernel which I
cleaned up and rebased. Thanks to Kernel Labs for that work.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add simple support for this 8 channel volume control driver.
Currently all it does is to unmute all 8 channels.
Based upon Devin's initial patch made for an older kernel which I
cleaned up and rebased. Thanks to Kernel Labs for that work.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is necessary since the *_std_setup functions rely on a valid state->std
field.
Also fix the cx23888_std_setup() to test for 60Hz instead of NTSC, just like
cx25840_std_setup() does.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
For those two devices the code wrote to addresses 0x115/6, but on
those devices those addresses have nothing to do with power controls.
So clearly this never worked. Rather than writing to bogus addresses,
just do nothing for the cx2388x and cx231xx.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The cx23888 reports a slightly different Vsrc value than the other
chip variants do. Relax the check by 1, otherwise cx25840_set_fmt()
would fail for the cx23888.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The cx23888 also moves the following registers around:
!cx23888 cx23888
-------- -------
0x418, 0x41c 0x434, 0x438
0x420 0x418 (expect for bit 29 which has a different meaning)
0x478 0x454
Also drop the set_input code where the scaler is changed: this does not
belong here, changing the input should not change the scaler.
And that's besides the fact that that code is plain wrong.
After this change the cx23888 behaves much better. In particular, calling
set_input no longer changes the saturation to 0, causing a grayscale
image.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The cx23888 has the VBI registers at different addresses compared to
the other variants. In most cases it is a fixed offset, but not always.
Update the code so the right registers are written for the cx23888.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
These two drivers reported the pixel aspect ratio the wrong way around.
This caused qv4l2 to scale the image incorrectly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The pixelaspect ratio was set incorrectly for 60Hz formats.
And since cropcap wasn't implemented at all for the -417 (compressed
video) the pixelaspect was unknown for compressed video.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
While testing the cx23885 driver with various TV standards I found
a number of bugs:
1) norm_maxw() returned 768 instead of 720 for PAL formats. This should
always be 720, so drop this inline function and just always use 720.
2) cropcap() was missing, so the pixelaspect was never known and qv4l2 would
scale the image incorrectly. Add cropcap support.
3) cx23885_set_tvnorm() should just return 0 if the same standard was
set again. If another standard is set, then reset the width/height and
call set_fmt for the subdevs.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Double fetch vulnerabilities that happen when a variable is
fetched twice from shared memory but a security check is only
performed the first time.
The xen_pcibk_do_op function performs a switch statements on the op->cmd
value which is stored in shared memory. Interestingly this can result
in a double fetch vulnerability depending on the performed compiler
optimization.
This patch fixes it by saving the xen_pci_op command before
processing it. We also use 'barrier' to make sure that the
compiler does not perform any optimization.
This is part of XSA155.
CC: stable@vger.kernel.org
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Jan Beulich <JBeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The copy of the ring request was lacking a following barrier(),
potentially allowing the compiler to optimize the copy away.
Use RING_COPY_REQUEST() to ensure the request is copied to local
memory.
This is part of XSA155.
CC: stable@vger.kernel.org
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Since indirect descriptors are in memory shared with the frontend, the
frontend could alter the first_sect and last_sect values after they have
been validated but before they are recorded in the request. This may
result in I/O requests that overflow the foreign page, possibly
overwriting local pages when the I/O request is executed.
When parsing indirect descriptors, only read first_sect and last_sect
once.
This is part of XSA155.
CC: stable@vger.kernel.org
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
A compiler may load a switch statement value multiple times, which could
be bad when the value is in memory shared with the frontend.
When converting a non-native request to a native one, ensure that
src->operation is only loaded once by using READ_ONCE().
This is part of XSA155.
CC: stable@vger.kernel.org
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Instead of open-coding memcpy()s and directly accessing Tx and Rx
requests, use the new RING_COPY_REQUEST() that ensures the local copy
is correct.
This is more than is strictly necessary for guest Rx requests since
only the id and gref fields are used and it is harmless if the
frontend modifies these.
This is part of XSA155.
CC: stable@vger.kernel.org
Reviewed-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The last from guest transmitted request gives no indication about the
minimum amount of credit that the guest might need to send a packet
since the last packet might have been a small one.
Instead allow for the worst case 128 KiB packet.
This is part of XSA155.
CC: stable@vger.kernel.org
Reviewed-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Using RING_GET_REQUEST() on a shared ring is easy to use incorrectly
(i.e., by not considering that the other end may alter the data in the
shared ring while it is being inspected). Safe usage of a request
generally requires taking a local copy.
Provide a RING_COPY_REQUEST() macro to use instead of
RING_GET_REQUEST() and an open-coded memcpy(). This takes care of
ensuring that the copy is done correctly regardless of any possible
compiler optimizations.
Use a volatile source to prevent the compiler from reordering or
omitting the copy.
This is part of XSA155.
CC: stable@vger.kernel.org
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Adding tracepoints to inline functions adds tracepoint invocation code
for each instance where the function is inlined. The resulting increase
in kernel code size can have negative impact:
- More cache misses in instruction cache
- Reduced amount of DMA-capable memory
Therefore change all functions implementing I/O instructions from inline
to normal functions.
Bloat-o-meter summary after change (using performance_defconfig):
add/remove: 24/2 grow/shrink: 4/39 up/down: 2205/-4858 (-2653)
Signed-off-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
