The <dt-bindings/pinctrl/omap.h> header file defines a set of macros
for different SoCs families that falls under the OMAP sub-arch, that
allow to define the padconf register physical address instead of the
register offset from the padconf base.
But the am43xx and dra7xx SoCs families have their own pinctrl header
file so the DTS using these SoCs aren't able to use the AM4372_IOPAD()
and DRA7XX_CORE_IOPAD() macros since <dt-bindings/pinctrl/omap.h> is
not included.
Move the macros to the correct header files so can be used by the DTS.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Allow the topcliff-pch driver to be built for MIPS platforms, in
preparation for use on the MIPS Boston board.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The VPD page information might change, so we need to be able to update
it. This patch implements a VPD page rescan whenever the 'rescan' sysfs
attribute is triggered.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Shane Seymour <shane.seymour@hpe.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The es2 chip doesn't have VID/PID programmed into the hardware and we
need to hack that up to distinguish different modules and their firmware
packages.
This fetches VID/PID (over firmware protocol) for es2 chip only, when
VID/PID already sent during hotplug are 0.
Since only the bootrom contains a firmware protocol cport, this only
affects bootrom's working and not nuttx.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
One of the input path used in the Allwinner codec is the MIC1. Add support
for it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This mbox_chan_ops structure is never modified, so declare it as const,
like all the other mbox_chan_ops structures.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Nizam Haider <nijamh@cdac.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When I connect an Intel SSD to SATA SIL controller (PCI ID 1095:3114), any
TRIM command results in I/O errors being reported in the log. There is
other similar error reported with TRIM and the SIL controller:
https://bugs.centos.org/view.php?id=5880
Apparently the controller doesn't support TRIM commands. This patch
disables TRIM support on the SATA SIL controller.
ata7.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata7.00: BMDMA2 stat 0x50001
ata7.00: failed command: DATA SET MANAGEMENT
ata7.00: cmd 06/01:01:00:00:00/00:00:00:00:00/a0 tag 0 dma 512 out
res 51/04:01:00:00:00/00:00:00:00:00/a0 Emask 0x1 (device error)
ata7.00: status: { DRDY ERR }
ata7.00: error: { ABRT }
ata7.00: device reported invalid CHS sector 0
sd 8:0:0:0: [sdb] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
sd 8:0:0:0: [sdb] tag#0 Sense Key : Illegal Request [current] [descriptor]
sd 8:0:0:0: [sdb] tag#0 Add. Sense: Unaligned write command
sd 8:0:0:0: [sdb] tag#0 CDB: Write same(16) 93 08 00 00 00 00 00 21 95 88 00 20 00 00 00 00
blk_update_request: I/O error, dev sdb, sector 2200968
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
mn10300 builds fail with
fs/stat.c: In function 'cp_old_stat':
fs/stat.c:163:2: error: 'old_uid_t' undeclared
ipc/util.c: In function 'ipc64_perm_to_ipc_perm':
ipc/util.c:540:2: error: 'old_uid_t' undeclared
Select CONFIG_HAVE_UID16 and remove local definition of CONFIG_UID16
to fix the problem.
Fixes: fbc416ff86 ("arm64: fix building without CONFIG_UID16")
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Current code doesn't update port value of Port Multiplier(PM) when
sending FIS of softreset to device, command will fail if FBS is
enabled.
There are two ways to fix the issue: the first is to disable FBS
before sending softreset command to PM device and the second is
to update port value of PM when sending command.
For the first way, i can't find any related rule in AHCI Spec. The
second way can avoid disabling FBS and has better performance.
Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Remove unused definitions, and this is to avoid confusion with MIPS-based
platforms.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Whereas ARM-based platforms have four phy interface registers and
information, the MIPS-based platforms have only three registers, and
there are no information and documentation. In the original BSP, It
using "strict-ahci" did not control these registers.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
The most MIPS-based platforms need to disable NCQ while have the NCQ
capability in HOST_CAP, and several ARM-based platforms (eg. BCM7349A0,
BCM7445A0, BCM7445B0) need to disable too.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
I2C controller used in Keystone SoC has an undocumented peculiarity which
results in SDA-SCL margins being dependent on module clock. Driving high
capacity bus near its limits can result in STOP condition sometimes being
understood as REPEATED-START by slaves (or NACK instead of ACK, etc...).
Driving the module with higher clocks increases the margin between SDA and SCL
transitions, making the operations with higher bus rates more robust. Therefore,
target the module clock to 12MHz instead of 7MHz, still staying within
the specification limits.
Before the change STOP timing looked like this on 400kHz:
SDA ----------+ +----
\ /
\ /
+----+
(1)
SCL --+ +------------
\ /
\ /
+----+
(2)
While only point (1) signals STOP, point (2) could be incorrectly recognized as
repeated-START (almost no margin between SDA and SCL transitions).
After the change there is at least 600ns margin measured between SCL fall and
SDA fall during STOP generation:
SDA ------+ +----
\ /
\ /
+----+
SCL --+ +--------
\ /
\ /
+----+
->| |<- 600ns
->| |<- tSUSTO
So called tSUSTO (setup time for STOP condition) is still slightly higher than
600ns, so no problem here.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When debugging firmware problems it's useful to check checksums of each
component. Add a debugfs interface to retrieve crc32 checksums:
# cat /sys/kernel/debug/ieee80211/phy0/ath10k/fw_checksums
firmware-N.bin cc3fb466
athwlan c0089f21
otp f3efeb4f
codeswap 00000000
board-N.bin bebc7c08
board bebc7c08
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Earlier we printed all the info messages after a successful device
initialisation and firmware boot, but that's problematic if something goes
wrong and there's no easy way to know what firmware version was used and so on.
Split the info messages into smaller pieces and print them as soon as we have
the info available.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA988X firmware starting from 10.2.4.70.12-2 has capability to support
Mesh Control Field Present bit in QoS field in native Wi-Fi mode.
Hence apply Mesh subtype according to the WMI service map.
Firmware will allows unicast, broadcast, multicast, and WDS frame
(FromDS = 1 and ToDS = 1) to be received via the interface, once Mesh
subtype is used.
The firmware and this patch together make native Wi-Fi mode comply to
IEEE802.11s Mesh frame in open mode, but the firmware doesn't yet
support secured Mesh mode.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA988X firmware starting from 10.2.4.70.12-2 supports new
vdev subtypes for proxy STA and Mesh, hence add them to be used
as needed.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Update WMI 10.x service map to sync with firmware 10.2.4.70.12-2
released on 11/11/2015 which is the latest QCA988X firmware as of
11/18/2015.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix write permission for few of the debugfs entries
which support write file operations as well.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Allocations from the DMA zone were originally added for legacy ISA
stuff, or PCI devices that have specific limitations in their DMA
addressing capabilities. It has no place in ath10k, which can do
full 32-bit DMA.
Fixes memory allocation errors on some platforms.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable AP + STA interface combination support for 10.x and
this enables Repeater mode testing (with WDS Repeater combinations
as well). Fix indentation as well.
Based on the suggestions from Michal and Yanbo Li,
thanks to them
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The error message order of board data fetch is board info,
directory, and then file name, hence place print arguments
in the order.
Fixes: 0a51b343ab ("ath10k: add board 2 API support")
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
According to the datasheets the n factor for dividing the tclk is
2 to the power n on Allwinner SoCs, not 2 to the power n + 1 as it is
on other mv64xxx implementations.
I've contacted Allwinner about this and they have confirmed that the
datasheet is correct.
This commit fixes the clk-divider calculations for Allwinner SoCs
accordingly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Now that we know that the forking task can't migrate amd the child is always
moved to the same cgroup by cgroup_post_fork()->css_set_move_task() we can
change pids_can_fork() and pids_cancel_fork() to just use task_css(current).
And since we no longer need to pin this css, we can remove pid_fork().
Note: the patch uses task_css_check(true), perhaps it makes sense to add a
helper or change task_css_set_check() to take cgroup_threadgroup_rwsem into
account.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Zefan Li <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
If the new child migrates to another cgroup before cgroup_post_fork() calls
subsys->fork(), then both pids_can_attach() and pids_fork() will do the same
pids_uncharge(old_pids) + pids_charge(pids) sequence twice.
Change copy_process() to call threadgroup_change_begin/threadgroup_change_end
unconditionally. percpu_down_read() is cheap and this allows other cleanups,
see the next changes.
Also, this way we can unify cgroup_threadgroup_rwsem and dup_mmap_sem.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Zefan Li <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
A css_set represents the relationship between a set of tasks and
css's. css_set never pinned the associated css's. This was okay
because tasks used to always disassociate immediately (in RCU sense) -
either a task is moved to a different css_set or exits and never
accesses css_set again.
Unfortunately, afcf6c8b75 ("cgroup: add cgroup_subsys->free() method
and use it to fix pids controller") and patches leading up to it made
a zombie hold onto its css_set and deref the associated css's on its
release. Nothing pins the css's after exit and it might have already
been freed leading to use-after-free.
general protection fault: 0000 [#1] PREEMPT SMP
task: ffffffff81bf2500 ti: ffffffff81be4000 task.ti: ffffffff81be4000
RIP: 0010:[<ffffffff810fa205>] [<ffffffff810fa205>] pids_cancel.constprop.4+0x5/0x40
...
Call Trace:
<IRQ>
[<ffffffff810fb02d>] ? pids_free+0x3d/0xa0
[<ffffffff810f8893>] cgroup_free+0x53/0xe0
[<ffffffff8104ed62>] __put_task_struct+0x42/0x130
[<ffffffff81053557>] delayed_put_task_struct+0x77/0x130
[<ffffffff810c6b34>] rcu_process_callbacks+0x2f4/0x820
[<ffffffff810c6af3>] ? rcu_process_callbacks+0x2b3/0x820
[<ffffffff81056e54>] __do_softirq+0xd4/0x460
[<ffffffff81057369>] irq_exit+0x89/0xa0
[<ffffffff81876212>] smp_apic_timer_interrupt+0x42/0x50
[<ffffffff818747f4>] apic_timer_interrupt+0x84/0x90
<EOI>
...
Code: 5b 5d c3 48 89 df 48 c7 c2 c9 f9 ae 81 48 c7 c6 91 2c ae 81 e8 1d 94 0e 00 31 c0 5b 5d c3 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 <f0> 48 83 87 e0 00 00 00 ff 78 01 c3 80 3d 08 7a c1 00 00 74 02
RIP [<ffffffff810fa205>] pids_cancel.constprop.4+0x5/0x40
RSP <ffff88001fc03e20>
---[ end trace 89a4a4b916b90c49 ]---
Kernel panic - not syncing: Fatal exception in interrupt
Kernel Offset: disabled
---[ end Kernel panic - not syncing: Fatal exception in interrupt
Fix it by making css_set pin the associate css's until its release.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Reported-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Link: http://lkml.kernel.org/g/20151120041836.GA18390@codemonkey.org.uk
Link: http://lkml.kernel.org/g/5652D448.3080002@bmw-carit.de
Fixes: afcf6c8b75 ("cgroup: add cgroup_subsys->free() method and use it to fix pids controller")
The Kirkwood v5 platforms need their CPUIDLE driver, so put it
into the defconfig.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This just regenerates the v5 mvebu defconfig with the latest
defaults so as to avoid too much fuzz when applying patches to
it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
On 64-bit with CONFIG_SPI_DEBUG=y and #define VERBOSE:
drivers/spi/spidev.c:287:3: warning: format '%zd' expects argument of type 'signed size_t', but argument 4 has type '__u32' [-Wformat=]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
MSIOF in SH-Mobile AG5 (sh73a0) is handled fine by the existing driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Prefix all partition reg properties to 32-bit to ease readability.
While at it, also remove a stale x in front of boot partition
offset and make some upper-case hex numbers lower-case.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
NAND flash partitions should be part of a partitions sub-node
not the flash node itself. Move the partitions which will also
allow different bootloaders get rid of the stock partitions
easily by removing the partitions node.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Current NAND node has an additional flash partition for the whole
flash overlapping with real partitions. Remove this partition as
the whole flash is already represented by the NAND device itself.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Some ACPI node's _STA will touch operation region field, since the
evaluation of _STA in acpi_bus_type_and_status is very early, the
operation region handler is not ready yet. Instead of fail that function
and not creating the acpi_device node consequently, set status to 0 so
that later when the driver for that device is probing, it can find
the acpi_device node and proceed normally. And at that time, the
handler for the operation region is ready and its _STA evaluation will
succeed, its present status can be checked there.
Even there will be no driver using this node later, it doesn't seem
hurt to have one more acpi_device node created with status set to 0.
This happens on Microsoft Surface 3, where the SPI device node NTRG's
_STA touches GPIO fields and the SPI core driver will only enumerate SPI
devices from ACPI if the acpi_device node is 1: created; 2: _STA
indicates it's present.
Note that due to another problem in SPI driver, for NTRG to be actually
enumerated, some changes have to be made in the SPI layer, which is
addressed by Mika(not send out yet):
https://bugzilla.kernel.org/show_bug.cgi?id=104291#c23
Link: https://bugzilla.kernel.org/show_bug.cgi?id=104291
Reported-by: Bastien Nocera <bugzilla@hadess.net>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are two common expectations among several subsystems/drivers that
deploys runtime PM support, but which isn't met by the driver core.
Expectation 1)
At ->probe() the subsystem/driver expects the runtime PM status of the
device to be RPM_SUSPENDED, which is the initial status being assigned at
device registration.
This expectation is especially common among some of those subsystems/
drivers that manages devices with an attached PM domain, as those requires
the ->runtime_resume() callback at the PM domain level to be invoked
during ->probe().
Moreover these subsystems/drivers entirely relies on runtime PM resources
being managed at the PM domain level, thus don't implement their own set
of runtime PM callbacks.
These are two scenarios that suffers from this unmet expectation.
i) A failed ->probe() sequence requests probe deferral:
->probe()
...
pm_runtime_enable()
pm_runtime_get_sync()
...
err:
pm_runtime_put()
pm_runtime_disable()
...
As there are no guarantees that such sequence turns the runtime PM status
of the device into RPM_SUSPENDED, the re-trying ->probe() may start with
the status in RPM_ACTIVE.
In such case the runtime PM core won't invoke the ->runtime_resume()
callback because of a pm_runtime_get_sync(), as it considers the device to
be already runtime resumed.
ii) A driver re-bind sequence:
At driver unbind, the subsystem/driver's >remove() callback invokes a
sequence of runtime PM APIs, to undo actions during ->probe() and to put
the device into low power state.
->remove()
...
pm_runtime_put()
pm_runtime_disable()
...
Similar as in the failing ->probe() case, this sequence don't guarantee
the runtime PM status of the device to turn into RPM_SUSPENDED.
Trying to re-bind the driver thus causes the same issue as when re-trying
->probe(), in the probe deferral scenario.
Expectation 2)
Drivers that invokes the pm_runtime_irq_safe() API during ->probe(),
triggers the runtime PM core to increase the usage count for the device's
parent and permanently make it runtime resumed.
The usage count is only dropped at device removal, which also allows it to
be runtime suspended again.
A re-trying ->probe() repeats the call to pm_runtime_irq_safe() and thus
once more triggers the usage count of the device's parent to be increased.
This leads to not only an imbalance issue of the usage count of the
device's parent, but also to keep it runtime resumed permanently even if
->probe() fails.
To address these issues, let's change the policy of the driver core to
meet these expectations. More precisely, at ->probe() failures and driver
unbind, restore the initial states of runtime PM.
Although to still allow subsystem's to control PM for devices that doesn't
->probe() successfully, don't restore the initial states unless runtime PM
is disabled.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is unsafe [1] if probing of devices will happen during suspend or
hibernation and system behavior will be unpredictable in this case.
So, let's prohibit device's probing in dpm_prepare() and defer their
probing instead. The normal behavior will be restored in
dpm_complete().
This patch introduces new DD core APIs:
device_block_probing()
It will disable probing of devices and defer their probes instead.
device_unblock_probing()
It will restore normal behavior and trigger re-probing of deferred
devices.
[1] https://lkml.org/lkml/2015/9/11/554
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
IRQ should be disabled on device probe so that the device IRQ is in a
known starting state. If IRQ is not disabled, interrupts may be reported
as handled by the IRQ handler, despite no irq_unmask calls made by the
user.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds support for port names for the SB800 chipset.
Since the chipset supports a multiplexed main SMBus controller, adding
the channel name to the adapter name is necessary to differentiate the
ports better (for example in sensors output).
Signed-off-by: Christian Fetzer <fetzer.ch@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The SB800 chipset supports a multiplexed main SMBus controller with
four ports. The multiplexed ports share the same SMBus address and
register set. The port is selected by bits 2:1 of the smb_en register
(0x2C).
Only one port can be active at any point in time therefore a mutex is
needed in order to synchronize access.
Additionally, the commit avoids requesting and releasing the SMBus base
address index region on every multiplexed transfer by moving the
request_region call into piix4_probe.
Tested on HP ProLiant MicroServer G7 N54L (where this patch adds
support to access sensor data from the w83795adg).
Cc: Thomas Brandon <tbrandonau@gmail.com>
Cc: Eddi De Pieri <eddi@depieri.net>
Signed-off-by: Christian Fetzer <fetzer.ch@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The SB800 chipset supports a multiplexed main SMBus controller with
four ports. Therefore the static variable piix4_main_adapter is
converted into a piix4_main_adapters array that can hold one
i2c_adapter for each multiplexed port.
The auxiliary adapter remains unchanged since it represents the second
(not multiplexed) SMBus controller on the SB800 chipset.
Signed-off-by: Christian Fetzer <fetzer.ch@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Update the comments to match current behaviour. Shorten some comments.
Update copyrights.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If we don't clear START generation as soon as possible, it may cause
another message to be generated, e.g. when receiving NACK in address
phase. To keep the race window as small as possible, we clear it right
at the beginning of the interrupt. We don't need any checks since we
always want to stop START and STOP generation on the next occasion after
we started it.
This patch improves the situation but sadly does not completely fix it.
It is still to be researched if we can do better given this HW design.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Due to the HW design, master IRQs are timing critical, so give them
precedence over slave IRQ.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
