There is a stray '>' at the end of the mailing-list specified for the
Broadcom STB GPIO driver, remove that.
Fixes: 3b0213d56e ("gpio: Add GPIO support for Broadcom STB SoCs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Include bcm-kernel-feedback-list for all brcmstb patch submission to be
both consistent with how other Broadcom ARM-based SoCs are handled, and
get internal Broadcom people to review these changes.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The newly added suspend/resume implementation for ahci_mvebu causes
a link error when CONFIG_PM_SLEEP is disabled:
ERROR: "ahci_platform_suspend_host" [drivers/ata/ahci_mvebu.ko] undefined!
ERROR: "ahci_platform_resume_host" [drivers/ata/ahci_mvebu.ko] undefined!
This adds the same #ifdef here that exists in the ahci_platform driver
which defines the above functions.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: d6ecf15814 ("ata: ahci_mvebu: add suspend/resume support")
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The GTI.TIV may be set to 2GHz^2 / rate, where rate is
that of the clock of the device. Rather than assuming a
rate of 130MHz use the actual rate of the clock.
The motivation for this is to use the correct rate on
the r8a7795/Salvator-X which is advertised as 133MHz but
may differ depending on the extal present on the Salvator-X.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add suspend/resume support to dl2k driver.
This requires RX/TX rings to be reset so split out the required
functionality from alloc_list() into new rio_reset_ring().
Tested on Asus NX1101 (IP1000A) and D-Link DGE-550T (DL-2000).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move HW init and stop into separate functions.
Request IRQ only after the HW has been reset (so interrupts are
disabled and no stale interrupts are pending).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If memory allocation fails in alloc_list(), free the already allocated
memory and return -ENOMEM. In rio_open(), call alloc_list() first and
abort if it fails. Move HW access (set RFDListPtr) out ot alloc_list().
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
sound card rtd was an array and was updated to a list so update
the driver to use a list
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound card rtd was an array and was updated to a list so update
the driver to use a list
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
if CONFIG_OF=n:
drivers/clk/clk-cs2000-cp.c: In function ‘cs2000_remove’:
drivers/clk/clk-cs2000-cp.c:453:22: warning: unused variable ‘np’ [-Wunused-variable]
struct device_node *np = dev->of_node;
^
Convert dummies of_clk_del_provider() and of_clk_init() from macros to
static inline functions to kill such compiler warnings.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Since commit 5266698661 ("tipc: let broadcast packet
reception use new link receive function") the broadcast send
link state was meant to always be set to LINK_ESTABLISHED, since
we don't need this link to follow the regular link FSM rules. It
was also the intention that this state anyway shouldn't impact
the run-time working state of the link, since the latter in
reality is controlled by the number of registered peers.
We have now discovered that this assumption is not quite correct.
If the broadcast link is reset because of too many retransmissions,
its state will inadvertently go to LINK_RESETTING, and never go
back to LINK_ESTABLISHED, because the LINK_FAILURE event was not
anticipated. This will work well once, but if it happens a second
time, the reset on a link in LINK_RESETTING has has no effect, and
neither the broadcast link nor the unicast links will go down as
they should.
Furthermore, it is confusing that the management tool shows that
this link is in UP state when that obviously isn't the case.
We now ensure that this state strictly follows the true working
state of the link. The state is set to LINK_ESTABLISHED when
the number of peers is non-zero, and to LINK_RESET otherwise.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Maloy says:
====================
tipc: some cleanups and improvements
This series mostly contains cleanups and cosmetic code changes.
The only real functional change is in #4 and #5, where we change the
locking structure for nodes and links in order to permit full
concurrency between links working in parallel on different interfaces.
Since the groundwork for this has been done in previous commit series,
this change constitutes only the final, small step to achieve that goal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of variables with Hungarian notation (l_ptr, n_ptr etc.)
has been significantly reduced over the last couple of years.
We now root out the last traces of this practice.
There are no functional changes in this commit.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We move the definition of struct tipc_link from link.h to link.c in
order to minimize its exposure to the rest of the code.
When needed, we define new functions to make it possible for external
entities to access and set data in the link.
Apart from the above, there are no functional changes.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In our effort to have less code and include dependencies between
entities such as node, link and bearer, we try to narrow down
the exposed interface towards the node as much as possible.
In this commit, we move the definition of struct tipc_node, along
with many of its associated function declarations, from node.h to
node.c. We also move some function definitions from link.c and
name_distr.c to node.c, since they access fields in struct tipc_node
that should not be externally visible. The moved functions are renamed
according to new location, and made static whenever possible.
There are no functional changes in this commit.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the node FSM a node in state SELF_UP_PEER_UP cannot
change state inside a lock context, except when a TUNNEL_PROTOCOL
(SYNCH or FAILOVER) packet arrives. However, the node's individual
links may still change state.
Since each link now is protected by its own spinlock, we finally have
the conditions in place to convert the node spinlock to an rwlock_t.
If the node state and arriving packet type are rigth, we can let the
link directly receive the packet under protection of its own spinlock
and the node lock in read mode. In all other cases we use the node
lock in write mode. This enables full concurrent execution between
parallel links during steady-state traffic situations, i.e., 99+ %
of the time.
This commit implements this change.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparation to allow parallel links to work more independently
from each other we introduce a per-link spinlock, to be stored in the
struct nodes's link entry area. Since the node lock still is a regular
spinlock there is no increase in parallellism at this stage.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The file name_distr.c currently contains three functions,
named_cluster_distribute(), tipc_publ_subcscribe() and
tipc_publ_unsubscribe() that all directly access fields in
struct tipc_node. We want to eliminate such dependencies, so
we move those functions to the file node.c and rename them to
tipc_node_broadcast(), tipc_node_subscribe() and tipc_node_unsubscribe()
respectively.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function tipc_node_check_state() contains the core logics
for handling link synchronization and failover. For this reason,
it is important to keep it as comprehensible as possible.
In this commit, we make three small cleanups.
1) If the node is in state SELF_DOWN_PEER_LEAVING and the received
packet confirms that the peer has lost contact, there will be no
further action in this function. To make this clearer, we return
from the function directly after the state change.
2) Since commit 0f8b8e28fb ("tipc: eliminate risk of stalled
link synchronization") only the logically first TUNNEL_PROTO/SYNCH
packet can alter the link state and set the synch point,
independently of arrival order. Hence, there is not any longer any
need to adjust the synch value in case such packets arrive in
disorder. We remove this adjustment.
3) It is the intention that any message arriving on any of the links
may trig a check for and possible termination of a node SYNCH state.
A redundant and unnoticed check for tipc_link_is_synching() obviously
beats this purpose, with the effect that only packets arriving on the
synching link may currently end the synch state. We remove this check.
This change will further shorten the synchronization period between
parallel links.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 5cbb28a4bf ("tipc: linearize arriving NAME_DISTR
and LINK_PROTO buffers") we added linearization of NAME_DISTRIBUTOR,
LINK_PROTOCOL/RESET and LINK_PROTOCOL/ACTIVATE to the function
tipc_udp_recv(). The location of the change was selected in order
to make the commit easily appliable to 'net' and 'stable'.
We now move this linearization to where it should be done, in the
functions tipc_named_rcv() and tipc_link_proto_rcv() respectively.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
quadfs_pll_fs660c32_round_rate prints a few structure members
that are never initialized, and also doesn't print the only one
it cares about. We get a gcc warning about the ones that
are printed:
clk/st/clkgen-fsyn.c:560:93: warning: 'params.sdiv' may be used uninitialized in this function
clk/st/clkgen-fsyn.c:560:93: warning: 'params.mdiv' may be used uninitialized in this function
clk/st/clkgen-fsyn.c:560:93: warning: 'params.pe' may be used uninitialized in this function
clk/st/clkgen-fsyn.c:560:93: warning: 'params.nsdiv' may be used uninitialized in this function
This changes the code to no longer print uninitialized data, and
for good measure it also prints the ndiv member that is being
set.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 5f7aa9071e ("clk: st: Support for QUADFS inside ClockGenB/C/D/E/F")
Acked-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Commit dca1a4b5ff ("clk: at91: keep slow clk enabled to prevent system
hang") added a workaround for the slow clock as it is not properly handled
by its users.
Now that the slow clock is taken properly by the drivers, this workaround
is not necessary anymore, revert it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The X-Gene clock driver missed the divider shift operation when
set the divider value.
Signed-off-by: Loc Ho <lho@apm.com>
Fixes: 308964caee ("clk: Add APM X-Gene SoC clock driver")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This is according to figure 12 ("I2C Programming Procedure") in
"Si5351A/B/C Data Sheet"
(https://www.silabs.com/Support%20Documents/TechnicalDocs/Si5351-B.pdf).
Without the PLL soft reset, we were unable to get three outputs
working at the same time.
According to Silicon Labs support, performing PLL soft reset will only
be noticeable if the PLL parameters have been changed.
Signed-off-by: Jacob Siverskog <jacob@teenage.engineering>
Signed-off-by: Jens Rudberg <jens@teenage.engineering>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Commit 8b136baa58 ("spi: pxa2xx: Detect number of enabled Intel LPSS SPI
chip select signals") added a block where lpss_ssp_setup() gets called
again for Intel LPSS SPI host controllers before checking number of chip
selects from the capabilities register.
There is no point in calling the function twice in probe so remove the
first call.
Reported-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add device tree entries for clock support for Broadcom Northstar 2 SoC
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Replace current device tree dummy clocks with real clock support for
Broadcom Northstar Plus SoC
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Replace current device tree dummy clocks with real clock support for
Broadcom Northstar SoCs.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
64bit compiler indicates this without this patch
linux/sound/soc/sh/rcar/core.c: In function 'rsnd_probe':
linux/sound/soc/sh/rcar/core.c:1002:16: warning: cast from pointer to\
integer of different size [-Wpointer-to-int-cast]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
a3af0c65("ASoC: ak4613: add single-end optional property for IN/OUT pins")
added IN/OUT pin single-end optional property, but it used "ak4613" as
vendor prefix. This patch fixup to asahi-kasei.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the driver for the Powerventure PV88060 BUCKs and LDOs regulator.
It communicates via an I2C bus to the device.
Signed-off-by: James Ban <James.Ban.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The new optimized do_div implementation (now in asm-generic/next) exposes a
glitch in the brownstone audio driver by producing a compile-time warning:
sound/soc/pxa/brownstone.c: In function 'brownstone_wm8994_hw_params':
sound/soc/pxa/brownstone.c:67:85: warning: comparison of distinct pointer types lacks a cast
sound/soc/pxa/brownstone.c:67:10125: warning: right shift count >= width of type [-Wshift-count-overflow]
sound/soc/pxa/brownstone.c:67:10254: warning: passing argument 1 of '__div64_32' from incompatible pointer type [-Wincompatible-pointer-types]
The driver just divides two plain integer values, so it should not
use do_div to start with, but has apparently done so ever since the
code was first merged. This replaces do_div with a simple division
operator.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The second argument of the mutex_lock_nested() helper is only
evaluated if CONFIG_DEBUG_LOCK_ALLOC is set. Otherwise we
get this build warning for the new regulator_lock_supply
function:
drivers/regulator/core.c: In function 'regulator_lock_supply':
drivers/regulator/core.c:142:6: warning: unused variable 'i' [-Wunused-variable]
To avoid the warning, this restructures the code to make it
both simpler and to move the 'i++' outside of the mutex_lock_nested
call, where it is now always used and the variable is not
flagged as unused.
We had some discussion about changing mutex_lock_nested to an
inline function, which would make the code do the right thing here,
but in the end decided against it, in order to guarantee that
mutex_lock_nested() does not introduced overhead without
CONFIG_DEBUG_LOCK_ALLOC.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 9f01cd4a91 ("regulator: core: introduce function to lock regulators and its supplies")
Link: http://permalink.gmane.org/gmane.linux.kernel/2068900
Signed-off-by: Mark Brown <broonie@kernel.org>
All atmel_nand_caps are never modified, consitify them.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This is present on the Renesas r8a7795 SoC and may be
used by the Salvator-X board.
Also enable MICREL_PHY which is used on the Salvator-X board.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add an ethernet0 alias for the wired network card so that U-Boot can
find the device-node and add an appropriate "local-mac-address"
property.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As has been the practice for boards for 32bit ARM Renesas SoCs
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
