Generic battery handling code is spread between the pen and pad codepaths
since battery usages may appear in reports for either. This makes it
difficult to concisely see the logic involved. Since battery data is
not treated like other data (i.e., we report it through the power_supply
subsystem rather than through the input subsystem), it makes reasonable
sense to split the functionality out into its own functions.
This commit has the generic battery handling duplicate the same pattern
that is used by the pen, pad, and touch interfaces. A "mapping" function
is provided to set up the battery, an "event" function is provided to
update the battery data, and a "report" function is provided to notify
the power_supply subsystem after all the data has been read. We look at
the usage itself rather than its collection to determine if one of the
battery functions should handle it. Additionally, we unconditionally
call the "report" function since there is no particularly good way to
know if a report contained a battery usage; 'wacom_notify_battery()'
will filter out any duplicate updates, however.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
At the moment, our driver relies on 'wacom_battery_get_property()' to
determine the most likely battery state (e.g charging, discharging, or
full) based on the information available. It is not always possible
for the function to properly determine this, however. For instance,
whenever an AES pen leaves proximity the battery state becomes
indeterminite. This commit adds the ability to provide it with explict
state information if desired. Whenever explicit state is not required
(the majority of circumstances), WACOM_POWER_SUPPLY_STATUS_AUTO can
be used in its place.
Three uses of explicit battery status are added: two wireless disconnect
paths and the AES case mentioned above.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When support for the HID_DG_BATTERYSTRENGTH usage was added for AES devices,
it appears that the value was read, but never actually forwarded to the
power_supply subystem for userspace's benefit. Let's correct that.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
AES sensors use the value 0 to indicate "not available" rather than
"completely dead". Such values are often sent for dozens of reports
while the pen is being brought into proximity and can cause userspace
to get the wrong impression about the actual battery state.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The power_supply subsystem expects us to provide it with capacity values
measured in percent. In particular, AES devices (HID_DG_BATTERYSTRENGTH)
use the range 0-255, which needs to be rescaled. The MobileStudio Pro
(WACOM_HID_WD_BATTERY_LEVEL) uses the range 0-100, but there's no guarantee
that future devices will share the same range.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Process RENAME_EXCHANGE in affs_rename2() adding static
affs_xrename() based on affs_rename().
We remove headers from respective directories then
affect bh to other inode directory entries for swapping.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Currently AFFS only supports RENAME_NOREPLACE.
This patch isolates that method to a static function to
prepare RENAME_EXCHANGE addition.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This bug fixes a regression introduced by patch 0d1c7ae9d8.
The intent of the patch was to stop promoting glocks after a
file system is withdrawn due to a variety of errors, because doing
so results in a BUG(). (You should be able to unmount after a
withdraw rather than having the kernel panic.)
Unfortunately, it also stopped demotions, so glocks could not be
unlocked after withdraw, which means the unmount would hang.
This patch allows function do_xmote to demote locks to an
unlocked state after a withdraw, but not promote them.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
- kdump support, including two necessary memblock additions:
memblock_clear_nomap() and memblock_cap_memory_range()
- ARMv8.3 HWCAP bits for JavaScript conversion instructions, complex
numbers and weaker release consistency
- arm64 ACPI platform MSI support
- arm perf updates: ACPI PMU support, L3 cache PMU in some Qualcomm
SoCs, Cortex-A53 L2 cache events and DTLB refills, MAINTAINERS update
for DT perf bindings
- architected timer errata framework (the arch/arm64 changes only)
- support for DMA_ATTR_FORCE_CONTIGUOUS in the arm64 iommu DMA API
- arm64 KVM refactoring to use common system register definitions
- remove support for ASID-tagged VIVT I-cache (no ARMv8 implementation
using it and deprecated in the architecture) together with some
I-cache handling clean-up
- PE/COFF EFI header clean-up/hardening
- define BUG() instruction without CONFIG_BUG
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=SDkm
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- kdump support, including two necessary memblock additions:
memblock_clear_nomap() and memblock_cap_memory_range()
- ARMv8.3 HWCAP bits for JavaScript conversion instructions, complex
numbers and weaker release consistency
- arm64 ACPI platform MSI support
- arm perf updates: ACPI PMU support, L3 cache PMU in some Qualcomm
SoCs, Cortex-A53 L2 cache events and DTLB refills, MAINTAINERS update
for DT perf bindings
- architected timer errata framework (the arch/arm64 changes only)
- support for DMA_ATTR_FORCE_CONTIGUOUS in the arm64 iommu DMA API
- arm64 KVM refactoring to use common system register definitions
- remove support for ASID-tagged VIVT I-cache (no ARMv8 implementation
using it and deprecated in the architecture) together with some
I-cache handling clean-up
- PE/COFF EFI header clean-up/hardening
- define BUG() instruction without CONFIG_BUG
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (92 commits)
arm64: Fix the DMA mmap and get_sgtable API with DMA_ATTR_FORCE_CONTIGUOUS
arm64: Print DT machine model in setup_machine_fdt()
arm64: pmu: Wire-up Cortex A53 L2 cache events and DTLB refills
arm64: module: split core and init PLT sections
arm64: pmuv3: handle pmuv3+
arm64: Add CNTFRQ_EL0 trap handler
arm64: Silence spurious kbuild warning on menuconfig
arm64: pmuv3: use arm_pmu ACPI framework
arm64: pmuv3: handle !PMUv3 when probing
drivers/perf: arm_pmu: add ACPI framework
arm64: add function to get a cpu's MADT GICC table
drivers/perf: arm_pmu: split out platform device probe logic
drivers/perf: arm_pmu: move irq request/free into probe
drivers/perf: arm_pmu: split cpu-local irq request/free
drivers/perf: arm_pmu: rename irq request/free functions
drivers/perf: arm_pmu: handle no platform_device
drivers/perf: arm_pmu: simplify cpu_pmu_request_irqs()
drivers/perf: arm_pmu: factor out pmu registration
drivers/perf: arm_pmu: fold init into alloc
drivers/perf: arm_pmu: define armpmu_init_fn
...
kisskb build service reported ARC defconfig build failures in linux-next
| arch/arc/include/asm/mmu.h:75:21: error: 'NR_CPUS' undeclared here (not in a function)
| make[3]: *** [arch/arc/mm/ioremap.o] Error 1
| make[2]: *** [arch/arc/mm] Error 2
| make[1]: *** [arch/arc] Error 2
which I bisected to a subtle side-effect of a totally benign mm patch
("mm, vmalloc: properly track vmalloc users") which caused a header
include chain deviation - asm/mmu.h using NR_CPUS before including
linux/threads.h
Fix that by adding the dependnet header and while it at fix a related
header to include linux headers aheads of asm headers as sometimes that
slso triggers such issues !
Reported-by: noreply@ellerman.id.au
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Otherwise it is possible to trigger crashes due to the metadata being
inaccessible yet these methods don't safely account for that possibility
without these checks.
Cc: stable@vger.kernel.org
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Highlights include:
- Larger virtual address space on 64-bit server CPUs. By default we use a 128TB
virtual address space, but a process can request access to the full 512TB by
passing a hint to mmap().
- Support for the new Power9 "XIVE" interrupt controller.
- TLB flushing optimisations for the radix MMU on Power9.
- Support for CAPI cards on Power9, using the "Coherent Accelerator Interface
Architecture 2.0".
- The ability to configure the mmap randomisation limits at build and runtime.
- Several small fixes and cleanups to the kprobes code, as well as support for
KPROBES_ON_FTRACE.
- Major improvements to handling of system reset interrupts, correctly treating
them as NMIs, giving them a dedicated stack and using a new hypervisor call
to trigger them, all of which should aid debugging and robustness.
Many fixes and other minor enhancements.
Thanks to:
Alastair D'Silva, Alexey Kardashevskiy, Alistair Popple, Andrew Donnellan,
Aneesh Kumar K.V, Anshuman Khandual, Anton Blanchard, Balbir Singh, Ben
Hutchings, Benjamin Herrenschmidt, Bhupesh Sharma, Chris Packham, Christian
Zigotzky, Christophe Leroy, Christophe Lombard, Daniel Axtens, David Gibson,
Gautham R. Shenoy, Gavin Shan, Geert Uytterhoeven, Guilherme G. Piccoli,
Hamish Martin, Hari Bathini, Kees Cook, Laurent Dufour, Madhavan Srinivasan,
Mahesh J Salgaonkar, Mahesh Salgaonkar, Masami Hiramatsu, Matt Brown, Matthew
R. Ochs, Michael Neuling, Naveen N. Rao, Nicholas Piggin, Oliver O'Halloran,
Pan Xinhui, Paul Mackerras, Rashmica Gupta, Russell Currey, Sukadev
Bhattiprolu, Thadeu Lima de Souza Cascardo, Tobin C. Harding, Tyrel Datwyler,
Uma Krishnan, Vaibhav Jain, Vipin K Parashar, Yang Shi.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vSF3
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights include:
- Larger virtual address space on 64-bit server CPUs. By default we
use a 128TB virtual address space, but a process can request access
to the full 512TB by passing a hint to mmap().
- Support for the new Power9 "XIVE" interrupt controller.
- TLB flushing optimisations for the radix MMU on Power9.
- Support for CAPI cards on Power9, using the "Coherent Accelerator
Interface Architecture 2.0".
- The ability to configure the mmap randomisation limits at build and
runtime.
- Several small fixes and cleanups to the kprobes code, as well as
support for KPROBES_ON_FTRACE.
- Major improvements to handling of system reset interrupts,
correctly treating them as NMIs, giving them a dedicated stack and
using a new hypervisor call to trigger them, all of which should
aid debugging and robustness.
- Many fixes and other minor enhancements.
Thanks to: Alastair D'Silva, Alexey Kardashevskiy, Alistair Popple,
Andrew Donnellan, Aneesh Kumar K.V, Anshuman Khandual, Anton
Blanchard, Balbir Singh, Ben Hutchings, Benjamin Herrenschmidt,
Bhupesh Sharma, Chris Packham, Christian Zigotzky, Christophe Leroy,
Christophe Lombard, Daniel Axtens, David Gibson, Gautham R. Shenoy,
Gavin Shan, Geert Uytterhoeven, Guilherme G. Piccoli, Hamish Martin,
Hari Bathini, Kees Cook, Laurent Dufour, Madhavan Srinivasan, Mahesh J
Salgaonkar, Mahesh Salgaonkar, Masami Hiramatsu, Matt Brown, Matthew
R. Ochs, Michael Neuling, Naveen N. Rao, Nicholas Piggin, Oliver
O'Halloran, Pan Xinhui, Paul Mackerras, Rashmica Gupta, Russell
Currey, Sukadev Bhattiprolu, Thadeu Lima de Souza Cascardo, Tobin C.
Harding, Tyrel Datwyler, Uma Krishnan, Vaibhav Jain, Vipin K Parashar,
Yang Shi"
* tag 'powerpc-4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (214 commits)
powerpc/64s: Power9 has no LPCR[VRMASD] field so don't set it
powerpc/powernv: Fix TCE kill on NVLink2
powerpc/mm/radix: Drop support for CPUs without lockless tlbie
powerpc/book3s/mce: Move add_taint() later in virtual mode
powerpc/sysfs: Move #ifdef CONFIG_HOTPLUG_CPU out of the function body
powerpc/smp: Document irq enable/disable after migrating IRQs
powerpc/mpc52xx: Don't select user-visible RTAS_PROC
powerpc/powernv: Document cxl dependency on special case in pnv_eeh_reset()
powerpc/eeh: Clean up and document event handling functions
powerpc/eeh: Avoid use after free in eeh_handle_special_event()
cxl: Mask slice error interrupts after first occurrence
cxl: Route eeh events to all drivers in cxl_pci_error_detected()
cxl: Force context lock during EEH flow
powerpc/64: Allow CONFIG_RELOCATABLE if COMPILE_TEST
powerpc/xmon: Teach xmon oops about radix vectors
powerpc/mm/hash: Fix off-by-one in comment about kernel contexts ids
powerpc/pseries: Enable VFIO
powerpc/powernv: Fix iommu table size calculation hook for small tables
powerpc/powernv: Check kzalloc() return value in pnv_pci_table_alloc
powerpc: Add arch/powerpc/tools directory
...
Pull namespace updates from Eric Biederman:
"This is a set of small fixes that were mostly stumbled over during
more significant development. This proc fix and the fix to
posix-timers are the most significant of the lot.
There is a lot of good development going on but unfortunately it
didn't quite make the merge window"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
proc: Fix unbalanced hard link numbers
signal: Make kill_proc_info static
rlimit: Properly call security_task_setrlimit
signal: Remove unused definition of sig_user_definied
ia64: Remove unused IA64_TASK_SIGHAND_OFFSET and IA64_SIGHAND_SIGLOCK_OFFSET
ipc: Remove unused declaration of recompute_msgmni
posix-timers: Correct sanity check in posix_cpu_nsleep
sysctl: Remove dead register_sysctl_root
This patch removes useless nfs_readdir_get_array() and
nfs_readdir_release_array() as suggested by Trond Myklebust
nfs_readdir() calls nfs_revalidate_mapping() before
readdir_search_pagecache() , nfs_do_filldir(), uncached_readdir()
so mapping should be correct.
While kmap() can't fail, all subsequent error checks were removed
as well as unused labels.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
When using 'ls -l' to display a large directory, if noac option is used,
in function nfs_getattr() nfs_need_revalidate_inode() will always be true
for NFSv3 and the nfs_entry cache of the directory will be flushed. The
flush will lead to a fully reread of the directory entries from server.
To prevent the unnecessary RPCs, we need to check whether or not the
noac option is used, and always report the invocation of nfs_getattr()
as cache hit instead cache miss when it's on.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
If memory allocation fails for the callback data, we need to put the nfs_client
or we end up with an elevated refcount.
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Turns out our skills in decoding the CLKCFG register weren't good
enough. On this particular elk the answer we got was 400 MHz when
in reality the clock was running at 266 MHz, which then caused us
to program a bogus AUX clock divider that caused all AUX communication
to fail.
Sadly the docs are now in bit heaven, so the fix will have to be based
on empirical evidence. Using another elk machine I was able to frob
the FSB frequency from the BIOS and see how it affects the CLKCFG
register. The machine seesm to use a frequency of 266 MHz by default,
and fortunately it still boot even with the 50% CPU overclock that
we get when we bump the FSB up to 400 MHz.
It turns out the actual FSB frequency and the register have no real
link whatsoever. The register value is based on some straps or something,
but fortunately those too can be configured from the BIOS on this board,
although it doesn't seem to respect the settings 100%. In the end I was
able to derive the following relationship:
BIOS FSB / strap | CLKCFG
-------------------------
200 | 0x2
266 | 0x0
333 | 0x4
400 | 0x4
So only the 200 and 400 MHz cases actually match how we're currently
decoding that register. But as the comment next to some of the defines
says, we have been just guessing anyway.
So let's fix things up so that at least the 266 MHz case will work
correctly as that is actually the setting used by both the buggy
machine and my test machine.
The fact that 333 and 400 MHz BIOS settings result in the same register
value is a little disappointing, as that means we can't tell them apart.
However, according to the gmch datasheet for both elk and ctg 400 Mhz is
not even a supported FSB frequency, so I'm going to make the assumption
that we should decode it as 333 MHz instead.
Cc: stable@vger.kernel.org
Cc: Tomi Sarvela <tomi.p.sarvela@intel.com>
Reported-by: Tomi Sarvela <tomi.p.sarvela@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100926
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170504181530.6908-1-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Tomi Sarvela <tomi.p.sarvela@intel.com>
If the server returns NFS4ERR_CONN_NOT_BOUND_TO_SESSION because we
are trunking, then RECLAIM_COMPLETE must handle that by calling
nfs4_schedule_session_recovery() and then retrying.
Reported-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Tested-by: Chuck Lever <chuck.lever@oracle.com>
Whole point of randomization was to hide server uptime, but an attacker
can simply start a syn flood and TCP generates 'old style' timestamps,
directly revealing server jiffies value.
Also, TSval sent by the server to a particular remote address vary
depending on syncookies being sent or not, potentially triggering PAWS
drops for innocent clients.
Lets implement proper randomization, including for SYNcookies.
Also we do not need to export sysctl_tcp_timestamps, since it is not
used from a module.
In v2, I added Florian feedback and contribution, adding tsoff to
tcp_get_cookie_sock().
v3 removed one unused variable in tcp_v4_connect() as Florian spotted.
Fixes: 95a22caee3 ("tcp: randomize tcp timestamp offsets for each connection")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Tested-by: Florian Westphal <fw@strlen.de>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While working on another build error, I ran into several variations of
this dependency loop:
subsection "Kconfig recursive dependency limitations"
drivers/input/Kconfig:8: symbol INPUT is selected by VT
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/tty/Kconfig:12: symbol VT is selected by FB_STI
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/video/fbdev/Kconfig:677: symbol FB_STI depends on FB
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/video/fbdev/Kconfig:5: symbol FB is selected by DRM_KMS_FB_HELPER
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/gpu/drm/Kconfig:72: symbol DRM_KMS_FB_HELPER is selected by DRM_KMS_CMA_HELPER
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/gpu/drm/Kconfig:137: symbol DRM_KMS_CMA_HELPER is selected by DRM_HDLCD
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/gpu/drm/arm/Kconfig:6: symbol DRM_HDLCD depends on OF
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/of/Kconfig:4: symbol OF is selected by X86_INTEL_CE
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
arch/x86/Kconfig:523: symbol X86_INTEL_CE depends on X86_IO_APIC
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
arch/x86/Kconfig:1011: symbol X86_IO_APIC depends on X86_LOCAL_APIC
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
arch/x86/Kconfig:1005: symbol X86_LOCAL_APIC depends on X86_UP_APIC
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
arch/x86/Kconfig:980: symbol X86_UP_APIC depends on PCI_MSI
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/pci/Kconfig:11: symbol PCI_MSI is selected by AMD_IOMMU
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/iommu/Kconfig:106: symbol AMD_IOMMU depends on IOMMU_SUPPORT
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/iommu/Kconfig:5: symbol IOMMU_SUPPORT is selected by DRM_ETNAVIV
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/gpu/drm/etnaviv/Kconfig:2: symbol DRM_ETNAVIV depends on THERMAL
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/thermal/Kconfig:5: symbol THERMAL is selected by ACPI_VIDEO
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/acpi/Kconfig:183: symbol ACPI_VIDEO is selected by INPUT
This doesn't currently show up as I fixed the 'THERMAL' part of it,
but I noticed that the FB_STI dependency should not be there but
was introduced by slightly incorrect bug-fix patch that tried to
fix a link error.
Instead of selecting 'VT' to make us enter the drivers/video/console
directory at compile-time, it's sufficient to build the
drivers/video/console/sticore.c file by adding its directory
to when CONFIG_FB_STI is enabled. Alternatively, we could move the
sticore code to another directory that is always built when we
have at STI_CONSOLE or FB_STI enabled.
Fixes: 17085a9345 ("parisc: stifb: should depend on STI_CONSOLE")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
The attribute sizes for IFLA_BRPORT_MCAST_FLOOD and
IFLA_BRPORT_BCAST_FLOOD weren't accounted for in br_port_info_size()
when they were added. Do so now and also add the corresponding policy
entries:
Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: Mike Manning <mmanning@brocade.com>
Fixes: b6cb5ac833 ("net: bridge: add per-port multicast flood flag")
Fixes: 99f906e9ad ("bridge: add per-port broadcast flood flag")
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GPU cores with the DYNAMIC_FREQUENCY_SCALING feature bit set expect the
platform to provide the clock scaling and ignore any requests to use the
internal FSCALE divider. Writes to this register still work, but don't
have any effect on the GPU clock frequency.
Save the initial core and shader clock frequency and ask the platform
to provide a slower clock when cooling is requested.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
PA clock gating can be enabled when the right bugfix bit is present.
There are broken revs of GC4000 and GC2000, which need TX clock gating
to be disabled.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Without this, polling on the dma-buf (and presumably other devices
synchronizing against our rendering) would return immediately, even
while the BO was busy.
Signed-off-by: Eric Anholt <eric@anholt.net>
Cc: stable@vger.kernel.org
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Russell King <linux+etnaviv@armlinux.org.uk>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: etnaviv@lists.freedesktop.org
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
If we bail out of the submit before actually adding the cmdstream
to the kernel ring there is no valid fence to put. Make sure to skip
the fence_put in that case.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
SFM is mapping doublequote to 0xF020
Without this patch creating files with doublequote fails to Windows/Mac
Signed-off-by: Bjoern Jacke <bjacke@samba.org>
Signed-off-by: Steve French <smfrench@gmail.com>
CC: stable <stable@vger.kernel.org>
The driver emits multi-touch events for Magic Trackpad as well as Magic
Mouse, but it does not set keybits that are related to multi-touch event
for Magic Mouse; so set these keybits.
The keybits that are not set cause trouble because user programs often
probe these keybits for self-configuration and thus they cannot operate
properly if the keybits are not set.
One of such troubles is that libevdev will not be able to emit correct
touch count, causing gestures library failed to do fling stop.
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The following Smatch complaint was generated in response to commit
2a6cdbd ("HID: wacom: Introduce new 'touch_input' device"):
drivers/hid/wacom_wac.c:1586 wacom_tpc_irq()
error: we previously assumed 'wacom->touch_input' could be null (see line 1577)
The 'touch_input' and 'pen_input' variables point to the 'struct input_dev'
used for relaying touch and pen events to userspace, respectively. If a
device does not have a touch interface or pen interface, the associated
input variable is NULL. The 'wacom_tpc_irq()' function is responsible for
forwarding input reports to a more-specific IRQ handler function. An
unknown report could theoretically be mistaken as e.g. a touch report
on a device which does not have a touch interface. This can be prevented
by only calling the pen/touch functions are called when the pen/touch
pointers are valid.
Fixes: 2a6cdbd ("HID: wacom: Introduce new 'touch_input' device")
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
While honouring the DMA_ATTR_FORCE_CONTIGUOUS on arm64 (commit
44176bb38f: "arm64: Add support for DMA_ATTR_FORCE_CONTIGUOUS to
IOMMU"), the existing uses of dma_mmap_attrs() and dma_get_sgtable()
have been broken by passing a physically contiguous vm_struct with an
invalid pages pointer through the common iommu API.
Since the coherent allocation with DMA_ATTR_FORCE_CONTIGUOUS uses CMA,
this patch simply reuses the existing swiotlb logic for mmap and
get_sgtable.
Note that the current implementation of get_sgtable (both swiotlb and
iommu) is broken if dma_declare_coherent_memory() is used since such
memory does not have a corresponding struct page. To be addressed in a
subsequent patch.
Fixes: 44176bb38f ("arm64: Add support for DMA_ATTR_FORCE_CONTIGUOUS to IOMMU")
Reported-by: Andrzej Hajda <a.hajda@samsung.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
based on commit b3b42c0dea
("fs/affs: make export work with cold dcache")
This adds get_parent function so that nfs client can still work after
cache drop (Tested on NFS v4 with echo 3 > /proc/sys/vm/drop_caches)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
An upper type non directory dentry that is a copy up target
should have a reference to its lower copy up origin.
There are three ways for an upper type dentry to be instantiated:
1. A lower type dentry that is being copied up
2. An entry that is found in upper dir by ovl_lookup()
3. A negative dentry is hardlinked to an upper type dentry
In the first case, the lower reference is set before copy up.
In the second case, the lower reference is found by ovl_lookup().
In the last case of hardlinked upper dentry, it is not easy to
update the lower reference of the negative dentry. Instead,
drop the newly hardlinked negative dentry from dcache and let
the next access call ovl_lookup() to find its lower reference.
This makes sure that the inode number reported by stat(2) after
the hardlink is created is the same inode number that will be
reported by stat(2) after mount cycle, which is the inode number
of the lower copy up origin of the hardlink source.
NOTE that this does not fix breaking of lower hardlinks on copy
up, but only fixes the case of lower nlink == 1, whose upper copy
up inode is hardlinked in upper dir.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
When all layers are on the same underlying filesystem, let stat(2) return
st_dev/st_ino values of the copy up origin inode if it is known.
This results in constant st_ino/st_dev representation of files in an
overlay mount before and after copy up.
When the underlying filesystem support NFS exportfs, the result is also
persistent st_ino/st_dev representation before and after mount cycle.
Lower hardlinks are broken on copy up to different upper files, so we
cannot use the lower origin st_ino for those different files, even for the
same fs case.
When all overlay layers are on the same fs, use overlay st_dev for non-dirs
to get the correct result from du -x.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
stat(2) on overlay directories reports the overlay temp inode
number, which is constant across copy up, but is not persistent.
When all layers are on the same fs, report the copy up origin inode
number for directories.
This inode number is persistent, unique across the overlay mount and
constant across copy up.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
For directory entries, non zero oe->numlower implies OVL_TYPE_MERGE.
Define a new type flag OVL_TYPE_ORIGIN to indicate that an entry holds a
reference to its lower copy up origin.
For directory entries ORIGIN := MERGE && UPPER. For non-dir entries ORIGIN
means that a lower type dentry has been recently copied up or that we were
able to find the copy up origin from overlay.origin xattr.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
If overlay.origin xattr is found on a non-dir upper inode try to get lower
dentry by calling exportfs_decode_fh().
On failure to lookup by file handle to lower layer, do not lookup the copy
up origin by name, because the lower found by name could be another file in
case the upper file was renamed.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Sometimes it is interesting to know if an upper file is pure upper or a
copy up target, and if it is a copy up target, it may be interesting to
find the copy up origin.
This will be used to preserve lower inode numbers across copy up.
Store the lower inode file handle in upper inode extended attribute
overlay.origin on copy up to use it later for these cases. Store the lower
filesystem uuid along side the file handle, so we can validate that we are
looking for the origin file in the original fs.
If lower fs does not support NFS export ops store a zero sized xattr so we
can always use the overlay.origin xattr to distinguish between a copy up
and a pure upper inode.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Some features can only work when all layers are on the same fs. Test this
condition during mount time, so features can check them later.
Add helper ovl_same_sb() to return the common super block in case all
layers are on the same fs.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Routines that are set by xen_init_time_ops() use shared_info's
pvclock_vcpu_time_info area. This area is not properly available until
shared_info is mapped in xen_setup_shared_info().
This became especially problematic due to commit dd759d93f4 ("x86/timers:
Add simple udelay calibration") where we end up reading tsc_to_system_mul
from xen_dummy_shared_info (i.e. getting zero value) and then trying
to divide by it in pvclock_tsc_khz().
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Commit 690b7f10b4f9f ("x86/xen: use capabilities instead of fake cpuid
values for xsave") introduced a regression as it tried to make use of
the fixup feature before it being available.
Fall back to the old variant testing via cpuid().
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
According to the SDM, if the "activate secondary controls" primary
processor-based VM-execution control is 0, no checks are performed on
the secondary processor-based VM-execution controls.
Signed-off-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
orderly_poweroff is triggered when a graceful shutdown
of system is desired. This may be used in many critical states of the
kernel such as when subsystems detects conditions such as critical
temperature conditions. However, in certain conditions in system
boot up sequences like those in the middle of driver probes being
initiated, userspace will be unable to power off the system in a clean
manner and leaves the system in a critical state. In cases like these,
the /sbin/poweroff will return success (having forked off to attempt
powering off the system. However, the system overall will fail to
completely poweroff (since other modules will be probed) and the system
is still functional with no userspace (since that would have shut itself
off).
However, there is no clean way of detecting such failure of userspace
powering off the system. In such scenarios, it is necessary for a backup
workqueue to be able to force a shutdown of the system when orderly
shutdown is not successful after a configurable time period.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
