The driver sets appropriate DMA mask. Delete the "dma-mask" DT
property. See [1] for negative comments for this binding.
[1] https://lkml.org/lkml/2016/2/8/57
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The current driver only supports the DMA engine up to 32 bit
physical address, but there also exists 64 bit capable DMA engine
for this IP.
The data DMA setup sequence is completely different, so I added the
64 bit DMA code as a new function denali_setup_dma64(). The 32 bit
one has been renamed to denali_setup_dma32().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
There are various customizable parameters, so several variants for
this IP. A generic compatible like "denali,denali-nand-dt" is
useless. Moreover, there are multiple things wrong with this string.
(Refer to Rob's comment [1])
The "denali,denali-nand-dt" was added by Altera for the SOCFPGA port.
Replace it with a more specific string "altr,socfpga-denali-nand".
There are no users (in upstream) of the old compatible string.
The Denali IP on SOCFPGA incorporates the hardware ECC fixup engine.
So, this capability should be associated with the compatible.
[1] https://lkml.org/lkml/2016/12/1/450
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Some old versions of the Denali IP (perhaps used only for Intel?)
detects ECC errors and provides correct data via a register, but
does not touch the transferred data. So, the software must fixup
the data in the buffer according to the provided ECC correction
information.
Newer versions perform ECC correction before transferring the data.
No more software intervention is needed. The ECC_ERROR_ADDRESS and
ECC_CORRECTION_INFO registers were deprecated. Instead, the number
of corrected bit-flips are reported via the ECC_COR_INFO register.
When an uncorrectable ECC error happens, a status flag is set to the
INTR_STATUS and ECC_COR_INFO registers.
As is often the case with this IP, the register view of INTR_STATUS
had broken compatibility.
For older versions (SW ECC fixup):
bit 0: ECC_TRANSACTION_DONE
bit 1: ECC_ERR
For newer versions (HW ECC fixup):
bit 0: ECC_UNCOR_ERR
bit 1: Reserved
Due to this difference, the irq_mask must be fixed too.
The existing handle_ecc() has been renamed to denali_sw_ecc_fixup()
for clarification.
What is unfortunate with this feature is we can not know the total
number of corrected/uncorrected errors in a page. The register
ECC_COR_INFO reports the maximum of per-sector bitflips. This is
useful for ->read_page return value, but ecc_stats.{corrected,failed}
increments may not be precise.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This part is wrong in multiple ways:
[1] is_erased() is called against "buf" twice, so the OOB area is
not checked at all. The second call should check chip->oob_poi.
[2] This code block is nested by double "if (check_erase_page)".
The inner one is redundant.
[3] The ECC_ERROR_ADDRESS register reports which sector(s) had
uncorrectable ECC errors. It is pointless to check the whole page
if only one sector contains errors.
[4] Unfortunately, the Denali ECC correction engine has already
manipulated the data buffer before it decides the bitflips are
uncorrectable. That is, not all of the data are 0xFF after an
erased page is processed by the ECC engine. The current is_erased()
helper could report false-positive ECC errors. Actually, a certain
mount of bitflips are allowed in an erased page. The core framework
provides nand_check_erased_ecc_chunk() that takes the threshold into
account. Let's use this.
This commit reworks the code to solve those problems.
Please note the erased page checking is implemented as a separate
helper function instead of embedding it in the loop in handle_ecc().
The reason is that OOB data are needed for the erased page checking,
but the controller can not start a new transaction until all ECC
error information is read out from the registers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This function is wrong in multiple ways:
[1] Counting corrected bytes instead of corrected bits.
The following code is counting the number of corrected _bytes_.
/* correct the ECC error */
buf[offset] ^= err_cor_value;
mtd->ecc_stats.corrected++;
bitflips++;
What the core framework expects is the number of corrected _bits_.
They can be different if multiple bitflips occur within one byte.
[2] total number of errors instead of max of per-sector errors
The core framework expects that corrected errors are counted per
sector, then the max value should be taken. The current code simply
iterates over the whole page, i.e. counts the total number of
correction in the page. This means "too many bitflips" is triggered
earlier than it should be, i.e. the NAND device is worn out sooner.
Besides those bugs, this function is unreadable due to the deep
nesting. Notice the whole code in this function is wrapped in
if (irq_status & INTR__ECC_ERR), so this conditional can be moved
out of the function. Also, use shorter names for local variables.
Re-work the function to fix all the issues.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The pipeline read-ahead function of the Denali IP enables continuous
reading from the device; while data is being read out by a CPU, the
controller maintains additional commands for streaming data from the
device. This will reduce the latency of the second page or later.
This feature is obviously no help for per-page accessors of Linux
NAND driver interface.
In the current implementation, the pipeline command is issued to
load a single page, then data are read out immediately. The use of
the pipeline operation is not adding any advantage, but just adding
complexity to the code. Remove.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Commit 28309572aa ("mtd: name the mtd device with an optional
label property") allow us to identify a chip in a user-friendly way.
If nand_set_flash_node() picks up the "label" from DT, let's respect
it. Otherwise, let it fallback to the current name "denali-nand".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The comment for ecc.read_page() requires that it should return
"0 if bitflips uncorrectable".
Actually, drivers could return positive values when uncorrectable
bitflips occur. For example, nand_read_page_swecc() is the case.
If ecc.correct() returns -EBADMSG for the first ECC sector, and
a positive value for the second one, nand_read_page_swecc() returns
a positive max_bitflips and increments ecc_stats.failed for the same
page.
The requirement can be relaxed by tweaking nand_do_read_ops().
Move the max_bitflips calculation below the retry.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The last/only user of the chip->write_page() hook (the Atmel NAND
controller driver) has been reworked and is no longer specifying a custom
->write_page() implementation.
Drop this hook before someone else start abusing it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The old NAND bindings were not exactly describing the hardware topology
and were preventing definitions of several NAND chips under the same
NAND controller.
New bindings address these limitations and should be preferred over the
old ones for new SoCs/boards.
Old bindings are still supported for backward compatibility but are
marked deprecated in the doc.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
This is a complete rewrite of the driver whose main purpose is to
support the new DT representation where the NAND controller node is now
really visible in the DT and appears under the EBI bus. With this new
representation, we can add other devices under the EBI bus without
risking pinmuxing conflicts (the NAND controller is under the EBI
bus logic and as such, share some of its pins with other devices
connected on this bus).
Even though the goal of this rework was not necessarily to add new
features, the new driver has been designed with this in mind. With a
clearer separation between the different blocks and different IP
revisions, adding new functionalities should be easier (we already
have plans to support SMC timing configuration so that we no longer
have to rely on the configuration done by the bootloader/bootstrap).
Also note that we no longer have a custom ->cmdfunc() implementation,
which means we can now benefit from new features added in the core
implementation for free (support for new NAND operations for example).
The last thing that we gain with this rework is support for multi-chips
and multi-dies chips, thanks to the clean NAND controller <-> NAND
devices representation.
During this transition we also dropped support for AVR32 SoCs which
should soon disappear from mainline (removal of the AVR32 arch is
planned for 4.12).
This new driver has been tested on several platforms (at91sam9261,
at91sam9g45, at91sam9x5, sama5d3 and sama5d4) to make sure it did not
introduce regressions, and it's worth mentioning that old bindings are
still supported (which partly explain the positive diffstat).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
While freeing inactive queue, check mvmsta to be valid before
dereferencing it. Found by Klocwork.
Signed-off-by: Sharon Dvir <sharon.dvir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Tested on HP Elite X2 1012 G1.
Matches event report of Lenovo Helix 2
(https://www.spinics.net/lists/ibm-acpi-devel/msg03982.html).
Signed-off-by: Maarten Maathuis <madman2003@shikahr.net>
[andy: fixed indentation of comments and massaged title of the change]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There's no need to have iwl_run_unified_mvm_ucode() be exposed
to other parts of the code since the logic to pick it over the
normal code in iwl_run_init_mvm_ucode() can just be done in
that function itself.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Rates were changed to adapt to HE. Change is backward compatible.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allocate buffers on HEAP instead of STACK for local structures
that are to be sent using usb_control_msg().
Signed-off-by: Maksim Salau <maksim.salau@gmail.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.8
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
With TASK_SIZE now reflecting the maximum size of the address space for
a process the code for arch_get_unmapped_area[_topdown] can be simplified.
Just let the logic pick a suitable address and deal with the page table
upgrade after the address has been selected.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
devm_gpiod_get_optional() can return -ENOSYS if GPIOLIB is
disabled, causing probe to fail. Warn the user if this
happens.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When recalculating the outer ICMPv6 checksum for a reverse path NATv6
such as ICMPV6_TIME_EXCEED nf_nat_icmpv6_reply_translation() was
accessing data beyond the headlen of the skb for non-linear skb. This
resulted in incorrect ICMPv6 checksum as garbage data was used.
Patch replaces csum_partial() with skb_checksum() which supports
non-linear skbs similar to nf_nat_icmp_reply_translation() from ipv4.
Signed-off-by: Dave Johnson <dave-kernel@centerclick.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently, after adding the following nft rules:
# nft add set x target1 { type ipv4_addr \; flags timeout \;}
# nft add rule x y set add ip daddr timeout 1d @target1 counter
the counters will always be zero despite of the elements are added
to the dynamic set "target1" or not, as we will break the nft expr
traversal unconditionally:
# nft list ruleset
...
set target1 {
...
elements = { 8.8.8.8 expires 23h59m53s}
}
chain output {
...
set add ip daddr timeout 1d @target1 counter packets 0 bytes 0
^ ^
...
}
Since we add the elements to the set successfully, we should continue
to the next expression.
Additionally, if elements are added to "flow table" successfully, we
will _always_ continue to the next expr, even if the operation is
_OP_ADD. So it's better to keep them to be consistent.
Fixes: 22fe54d5fe ("netfilter: nf_tables: add support for dynamic set updates")
Reported-by: Robert White <rwhite@pobox.com>
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When trying to redirect bridged frames to the bridge device itself or
a bridge port (brouting) via the dnat target then this currently fails:
The ethernet destination of the frame is dnat'ed to the MAC address of
the bridge device or port just fine. However, the IP code drops it in
the beginning of ip_input.c/ip_rcv() as the dnat target left
the skb->pkt_type as PACKET_OTHERHOST.
Fixing this by resetting skb->pkt_type to an appropriate type after
dnat'ing.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds a text line in the help section of the CAN_PEAK_USB
config item describing the support of the PCAN-USB X6 adapter, which is
already included in the Kernel since 4.9.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds the support of the PCAN-Chip USB, a stamp module for
customer hardware designs, which communicates via USB 2.0 with the
hardware. The integrated CAN controller supports the protocols CAN 2.0 A/B
as well as CAN FD. The physical CAN connection is determined by external
wiring. The Stamp module with its single-sided mounting and plated
half-holes is suitable for automatic assembly.
Note that the chip is equipped with the same logic than the PCAN-USB FD.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This driver provides support for the Arctic Sand arc2c0608 chip,
and provides a framework to support future devices.
Signed-off-by: Olimpiu Dejeu <olimpiu@arcticsand.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Olimpiu Dejeu <olimpiu@arcticsand.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Fixes: dabf54dd1c ("can: ti_hecc: Convert TI HECC driver to DT only driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Autoload the vcan module when a vcan instance is to be created by
'ip link add type vcan'
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Similar to the virtual ethernet driver veth, vxcan implements a
local CAN traffic tunnel between two virtual CAN network devices.
See Kconfig entry for details.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The CAN gateway was not implemented as per-net in the initial network
namespace support by Mario Kicherer (8e8cda6d73).
This patch enables the CAN gateway to be used in different namespaces.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The CAN_BCM protocol and its procfs entries were not implemented as per-net
in the initial network namespace support by Mario Kicherer (8e8cda6d73).
This patch adds the missing per-net functionality for the CAN BCM.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The statistics and its proc output was not implemented as per-net in the
initial network namespace support by Mario Kicherer (8e8cda6d73).
This patch adds the missing per-net statistics for the CAN subsystem.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
can_rx_alldev_list is a per-net data structure now. Remove it's definition
here and can_rx_dev_list too.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The namespace support for the CAN subsystem does not need any additional
memory. So when ".size = 0" there's no extra memory allocated by the system.
And therefore ".id" is obsolete too.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The can_rx_alldev_list is a per-net data structure now and allocated in
can_pernet_init(). Make sure the memory is free'd in can_pernet_exit() too.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
SocketCAN driver for Microchip CAN BUS Analyzer
(http://www.microchip.com/development-tools/)
Changes in v4:
- possible memory leak fixed in mcba_usb_write_bulk_callback
- LED support added
- failure handling in mcba_usb_probe improved
- C99 initializers for structs on stack
Changes in v3:
- improved/simplified CAN ID conversion
- functions for transmission of skb and cmd separated
- fixed/improved netif_stop_queue handling
- style/cosmetic corrections
Changes in v2:
- Termination handling reimplemented to fit new netlink API
(IFLA_CAN_TERMINATION)
- Bitrate handling reimplemented to fit new netlink API
(IFLA_CAN_BITRATE)
- CAN ID conversion refactored (changed from macro to inline functions)
- CAN DLC handling using get_can_dlc()
- Endianness handling for can_speed introduced
- Debugging removed
- Redundant error prints removed
- Style/cosmetic corrections (i.e. macro names, redefs, inits etc.)
Signed-off-by: Remigiusz Kołłątaj <remigiusz.kollataj@mobica.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
* Added defines for TX Event FIFO Element
* Adapted ndo_start_xmit function.
For versions >= v3.1.x it uses the TX FIFO to optimize the data
throughput. It stores the echo skb at the same index as in the
M_CAN's TX FIFO. The frame's message marker is set to this index.
This message marker is received in the TX Event FIFO after
the message was successfully transmitted. It is used to echo the
correct echo skb back to the network stack.
* Added m_can_echo_tx_event function. It reads all received
message markers in the TX Event FIFO and loops back the
corresponding echo skbs.
* ISR checks for new TX Event Entry interrupt for version >= 3.1.x.
Signed-off-by: Mario Huettel <mario.huettel@gmx.net>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
* TX/TX Event FIFO sizes are configured for version >= v3.1.x
Signed-off-by: Mario Huettel <mario.huettel@gmx.net>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adapts the initialization of the M_CAN. So it can be used
with all versions >= 3.0.x.
Changes:
* Added version element to m_can_priv structure to hold M_CAN version.
* Renamed bittiming structs for version 3.0.x
* Added new bittiming structs for version >= 3.1.x
* Function alloc_m_can_dev takes 2 new arguments. The TX FIFO size and the
base address of the module.
* Chip configuration for CAN_CTRLMODE_LOOPBACK is changed: Enabled
CCCR_MON bit. In combination with TEST_LBCK it activates the internal
loopback mode. Leaving CCCR_MON '0' results in external loopback mode.
* Clocks are temporarily enabled by platform_propbe function in order to
allow read access to the Core Release register and the Control Register.
Registers are used to detect M_CAN version and optional Non-ISO Feature.
Initialization of M_CAN for version >= 3.1.x:
* TX FIFO of M_CAN is used to transmit frames. The driver does not need to
stop the tx queue after each frame sent.
* Initialization of TX Event FIFO is added.
* NON-ISO is fixed for all M_CAN versions < 3.2.x. Version 3.2.x _can_ have
the NISO (Non-ISO) bit which can switch the mode of the M_CAN to Non-ISO
mode. This bit does not have to be writeable. Therefore it is checked.
If it is writable Non-ISO support is added to the controllers supported
CAN modes.
New Functions:
* Function to check the Core Release version. The read value determines the
behaviour of the driver.
* Function to check if the NISO bit for version >= 3.2.x is implemented.
Signed-off-by: Mario Huettel <mario.huettel@gmx.net>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
* Updated register defines to newest M_CAN version (v3.2.1).
* Changed defines in the whole code.
Signed-off-by: Mario Huettel <mario.huettel@gmx.net>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The virtual address of the device was printed. I removed it because it
leaks internal information.
Signed-off-by: Mario Huettel <mario.huettel@gmx.net>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
FIFO water marks disabled because the driver doesn't handle water mark
events.
Signed-off-by: Mario Huettel <mario.huettel@gmx.net>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
* Disabled interrupt line 1. The driver didn't use it.
Signed-off-by: Mario Huettel <mario.huettel@gmx.net>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds the support of the PCAN-PCI Express FD boards made
by PEAK-System, for computers using the PCI Express slot.
The PCAN-PCI Express FD has one or two CAN FD channels, depending
on the model. A galvanic isolation of the CAN ports protects
the electronics of the card and the respective computer against
disturbances of up to 500 Volts. The PCAN-PCI Express FD can be operated
with ambient temperatures in a range of -40 to +85 °C.
Such boards run an extented version of the CAN-FD IP running into USB
CAN-FD interfaces from PEAK-System, so this patch adds several new commands
and their corresponding data types to the PEAK CAN-FD common definitions
header file too.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The CAN-FD IP from PEAK-System runs into several kinds of PC CAN-FD
interfaces. Up to now, only the USB CAN-FD adapters were supported by
the Kernel. In order to prepare the adding of some new non-USB CAN-FD
interfaces, this patch moves - and rename - the IP definitions file
from its private (usb) sub-directory into a - newly created - CAN specific
one.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fixes the usage of the const qualifier in the memory pointer arguments
of the declared inline functions. By changing the line containing "const",
this patch also changes the name of the arg into a more usual one.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes the wrong usage of a specific USB data type into a common
header file. This common header file is intended to define the common data
types and values that define access to the PEAK-System CAN-FD IP, whatever
the PC interface is.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Use the module_pci_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The TASK_SIZE for a process should be maximum possible size of the address
space, 2GB for a 31-bit process and 8PB for a 64-bit process. The number
of page table levels required for a given memory layout is a consequence
of the mapped memory areas and their location.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
