Some SoCs like omap3 can configure GPIO irqs to use Linux generic
dedicated wakeirq support. If the dedicated wakeirq is configured,
the SoC will use a always-on interrupt controller to produce wake-up
events.
If bq24190 is configured for dedicated wakeirq, we need to check the
interrupt status on PM runtime resume. This is because the Linux
generic wakeirq will call pm_runtime_resume() on the device on a
wakeirq. And as the bq24190 interrupt is falling edge sensitive
and only active for 250 us, there will be no device interrupt seen
by the runtime SoC IRQ controller.
Note that this can cause spurious interrupts on omap3 devices with
bq24190 connected to gpio banks 2 - 5 as there's a glitch on those
pins waking from off mode as listed in "Advisory 1.45". Devices
with this issue should not configure the optional wakeirq interrupt
in the dts file.
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Liam Breck <kernel@networkimprov.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Few currently running test notification messages from run_vmtests output
have mismatched highlight lines. This commit fixes them to fit in
length.
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
trivial fix to spelling mistake in printed message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
This fixes a math error calculating the extra_vecs. The error assumed
only 1 cpu per vector, but the value needs to account for the actual
number of cpus per vector in order to get the correct remainder for
extra CPU assignment.
Fixes: 7bf8222b9b ("irq/affinity: Fix CPU spread for unbalanced nodes")
Reported-by: Xiaolong Ye <xiaolong.ye@intel.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Link: http://lkml.kernel.org/r/1492104492-19943-1-git-send-email-keith.busch@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The following warning results from holding a lane spinlock,
preempt_disable(), or the btt map spinlock and then trying to take the
reconfig_mutex to walk the poison list and potentially add new entries.
BUG: sleeping function called from invalid context at kernel/locking/mutex.
c:747
in_atomic(): 1, irqs_disabled(): 0, pid: 17159, name: dd
[..]
Call Trace:
dump_stack+0x85/0xc8
___might_sleep+0x184/0x250
__might_sleep+0x4a/0x90
__mutex_lock+0x58/0x9b0
? nvdimm_bus_lock+0x21/0x30 [libnvdimm]
? __nvdimm_bus_badblocks_clear+0x2f/0x60 [libnvdimm]
? acpi_nfit_forget_poison+0x79/0x80 [nfit]
? _raw_spin_unlock+0x27/0x40
mutex_lock_nested+0x1b/0x20
nvdimm_bus_lock+0x21/0x30 [libnvdimm]
nvdimm_forget_poison+0x25/0x50 [libnvdimm]
nvdimm_clear_poison+0x106/0x140 [libnvdimm]
nsio_rw_bytes+0x164/0x270 [libnvdimm]
btt_write_pg+0x1de/0x3e0 [nd_btt]
? blk_queue_enter+0x30/0x290
btt_make_request+0x11a/0x310 [nd_btt]
? blk_queue_enter+0xb7/0x290
? blk_queue_enter+0x30/0x290
generic_make_request+0x118/0x3b0
A spinlock is introduced to protect the poison list. This allows us to not
having to acquire the reconfig_mutex for touching the poison list. The
add_poison() function has been broken out into two helper functions. One to
allocate the poison entry and the other to apppend the entry. This allows us
to unlock the poison_lock in non-I/O path and continue to be able to allocate
the poison entry with GFP_KERNEL. We will use GFP_NOWAIT in the I/O path in
order to satisfy being in atomic context.
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Current codes invoke wrongly nf_ct_netns_get in the destroy routine,
it should use nf_ct_netns_put, not nf_ct_netns_get.
It could cause some modules could not be unloaded.
Fixes: ecb2421b5d ("netfilter: add and use nf_ct_netns_get/put")
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This can prevent the nft utility from printing out the auto generated
seed to the user, which is unnecessary and confusing.
Fixes: cb1b69b0b1 ("netfilter: nf_tables: add hash expression")
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
__nf_nat_decode_session is called from nf_nat_decode_session as decodefn.
before calling decodefn, it already set rcu_read_lock. so rcu_read_lock in
__nf_nat_decode_session can be removed.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
i915_gem_request_alloc() uses error pointers. It never returns NULLs.
Fixes: 0daf0113cf ("drm/i915: Mock infrastructure for request emission")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170413195217.GA26108@mwanda
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If the mmap_sem is contented then the vfio type1 IOMMU backend will
defer locked page accounting updates to a workqueue task. This has a
few problems and depending on which side the user tries to play, they
might be over-penalized for unmaps that haven't yet been accounted or
race the workqueue to enter more mappings than they're allowed. The
original intent of this workqueue mechanism seems to be focused on
reducing latency through the ioctl, but we cannot do so at the cost
of correctness. Remove this workqueue mechanism and update the
callers to allow for failure. We can also now recheck the limit under
write lock to make sure we don't exceed it.
vfio_pin_pages_remote() also now necessarily includes an unwind path
which we can jump to directly if the consecutive page pinning finds
that we're exceeding the user's memory limits. This avoids the
current lazy approach which does accounting and mapping up to the
fault, only to return an error on the next iteration to unwind the
entire vfio_dma.
Cc: stable@vger.kernel.org
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Kirti Wankhede <kwankhede@nvidia.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
If link training at a link rate optimal for a particular
mode fails during modeset's atomic commit phase, then we
let the modeset complete and then retry. We save the link rate
value at which link training failed, update the link status property
to "BAD" and use a lower link rate to prune the modes. It will redo
the modeset on the current mode at lower link rate or if the current
mode gets pruned due to lower link constraints then, it will send a
hotplug uevent for userspace to handle it.
This is also required to pass DP CTS tests 4.3.1.3, 4.3.1.4,
4.3.1.6.
This patch is a resend of the original commit id (233ce881dd
"drm/i915: Implement Link Rate fallback on Link training failure")
which got reverted in this commit id (afc1ebf456 Revert
"drm/i915: Implement Link Rate fallback on Link training failure")
due to CI failures.
After investigating the CI failures it was found that these
were essentially the failures which were always there but hidden because
they used to be DRM_DEBUG_KMS messages for link failures so never got
caught by CI. But now this patch actually throws DRM_ERROR if the link
training fails at RBR and 1 lane. So it caught these link train failures.
There were two failures:
1. On SKL 6700k this was because the machine in CI lab is a SKL desktop
without eDP on Port A. But our VBT initialization code in the driver writes
VBT defaults in a way that it always sets DP flag on Port A and this does
not get cleared after parsing the VBT outputs. This has been fixed in
commit id (bb1d132935 "drm/i915/vbt: split out defaults that are set
when there is no VBT) and (665788572c "drm/i915/vbt: don't propagate
errors from intel_bios_init())
2. On ILK-650 desktop - This was happening because of a bad monitor desktop
combination. I switched the monitor in the CI lab and that helped get rid
of the link failures on ILK system.
v10:
* Rebase on drm-tip and resend after revert
v9:
* Use the trimmed max values of link rate/lane count based on
link train fallback (Daniel Vetter)
v8:
* Set link_status to BAD first and then call mode_valid (Jani Nikula)
v7:
Remove the redundant variable in previous patch itself
v6:
* Obtain link rate index from fallback_link_rate using
the helper intel_dp_link_rate_index (Jani Nikula)
* Include fallback within intel_dp_start_link_train (Jani Nikula)
v5:
* Move set link status to drm core (Daniel Vetter, Jani Nikula)
v4:
* Add fallback support for non DDI platforms too
* Set connector->link status inside set_link_status function
(Jani Nikula)
v3:
* Set link status property to BAd unconditionally (Jani Nikula)
* Dont use two separate variables link_train_failed and link_status
to indicate same thing (Jani Nikula)
v2:
* Squashed a few patches (Jani Nikula)
Acked-by: Tony Cheng <tony.cheng@amd.com>
Acked-by: Harry Wentland <Harry.wentland@amd.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/16ca48b1e74c618929245e9a085b9e3483c3a16d.1491485983.git.jani.nikula@intel.com
The airplane mode button on Xiaomi's new laptops are the same as HP
laptops.
This is tested on Xiaomi Notebook Air 13.
Signed-off-by: Alex Hung <alex.hung@canonical.com>
[dvhart: Dropped module init/exit info messages]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Add touchscreen info for the Trekstor Surftab Wintron 7.0 ST70416-6
tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Set the initial voltage selector for vddpcie in case it's disabled
by default.
This fixes the below warning:
20c8000.anatop:regulator-vddpcie: Failed to read a valid default voltage selector.
anatop_regulator: probe of 20c8000.anatop:regulator-vddpcie failed with error -22
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Robin Gong <yibin.gong@nxp.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is needed for proper synchronization with display on another DRM
device (pl111 or tinydrm) with buffers produced by vc4 V3D. Fixes the
new igt vc4_dmabuf_poll testcase, and rendering of one of the glmark2
desktop tests on pl111+vc4.
This doesn't yet introduce waits on another device's fences before
vc4's rendering/display, because I don't have testcases for them.
v2: Reuse dma_fence_free(), retitle commit message to clarify that
it's not a full dma-buf fencing implementation yet.
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: http://patchwork.freedesktop.org/patch/msgid/20170412191202.22740-6-eric@anholt.net
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Johannes Berg says:
====================
netlink extended ACK reporting
Changes since v4:
* use __NLMSGERR_ATTR_MAX instead of NUM_NLMSGERR_ATTRS
Changes since v3:
* Add NLM_F_CAPPED and NLM_F_ACK_TLVS flags, to allow entirely
stateless parsing of the ACK messages by looking at the new
flags. Need to check NLM_F_ACK_TLVS first, since capping can
be done in kernels before this patchset without setting the
flag.
* Remove "missing_attr" functionality - this can obviously be
added back rather easily, but I'd rather have more discussion
about the nesting problem there.
* Improve documentation of NLMSGERR_ATTR_OFFS
* Improve message structure documentation, documenting that the
request message is always capped for success cases
* fix nlmsg_len of the outer message by calling nlmsg_end()
* fix memcpy() of the request in success cases, going back to
the original code that I'd changed before due to the payload
adjustments that I reverted when introducing tlvlen
Changes since v2:
* add NUM_NLMSGERR_ATTRS, NLMSGERR_ATTR_MAX
* fix cookie length to 20 (sha-1 length)
* move struct members for cookie to patch 3 where they should be
* another cleanup suggested by David Ahern
Changes since v1:
* credit Pablo and Jamal
* incorporate suggestion from David Ahern
* fix compilation in decnet
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the new extended ACK reporting struct to all of the generic
netlink parsing functions. For now, pass NULL in almost all callers
(except for some in the core.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have extended error reporting and a new message format for
netlink ACK messages, also extend this to be able to return arbitrary
cookie data on success.
This will allow, for example, nl80211 to not send an extra message for
cookies identifying newly created objects, but return those directly
in the ACK message.
The cookie data size is currently limited to 20 bytes (since Jamal
talked about using SHA1 for identifiers.)
Thanks to Jamal Hadi Salim for bringing up this idea during the
discussions.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the extended ACK reporting struct down from generic netlink to
the families, using the existing struct genl_info for simplicity.
Also add support to set the extended ACK information from generic
netlink users.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the base infrastructure and UAPI for netlink extended ACK
reporting. All "manual" calls to netlink_ack() pass NULL for now and
thus don't get extended ACK reporting.
Big thanks goes to Pablo Neira Ayuso for not only bringing up the
whole topic at netconf (again) but also coming up with the nlattr
passing trick and various other ideas.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When link transitions from LINK_FAIL to LINK_UP, the commit phase is
not called. This leads to an erroneous state causing slave-link state to
get stuck in "going down" state while its speed and duplex are perfectly
fine. This issue is a side-effect of splitting link-set into propose and
commit phases introduced by de77ecd4ef ("bonding: improve link-status
update in mii-monitoring")
This patch fixes these issues by calling commit phase whenever link
state change is proposed.
Fixes: de77ecd4ef ("bonding: improve link-status update in mii-monitoring")
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is necessary to provide ethtool support for displaying and
modifying parameters of dwc-xlgmac.
Signed-off-by: Jie Deng <jiedeng@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I have introduced this bug when applying and simplifying Paolo's patch
as we agreed on the list. The original was "x &= ~y; if (z) x |= y;".
Here is the story of a bad workflow:
A maintainer was already testing with the intended change, but it was
applied only to a testing repo on a different machine. When the time
to push tested patches to kvm/next came, he realized that this change
was missing and quickly added it to the maintenance repo, didn't test
again (because the change is trivial, right), and pushed the world to
fire.
Fixes: ae1e2d1082 ("kvm: nVMX: support EPT accessed/dirty bits")
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
This adds the serial slave device for the WL1835 Bluetooth interface.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Turns out that the LL protocol and the TI-ST are the same thing AFAICT.
The TI-ST adds firmware loading, GPIO control, and shared access for
NFC, FM radio, etc. For now, we're only implementing what is needed for
BT. This mirrors other drivers like BCM and Intel, but uses the new
serdev bus.
The firmware loading is greatly simplified by using existing
infrastructure to send commands. It may be a bit slower than the
original code using synchronous functions, but the real bottleneck is
likely doing firmware load at 115.2kbps.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are no users of hci_uart_init_tty, so remove it.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add serial slave device binding for the TI WiLink series of Bluetooth/FM/GPS
devices.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: netdev@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
1. Don't get the metric RTAX_ADVMSS of dst.
There are two reasons.
1) Its caller dst_metric_advmss has already invoke dst_metric_advmss
before invoke default_advmss.
2) The ipv4_default_advmss is used to get the default mss, it should
not try to get the metric like ip6_default_advmss.
2. Use sizeof(tcphdr)+sizeof(iphdr) instead of literal 40.
3. Define one new macro IPV4_MAX_PMTU instead of 65535 according to
RFC 2675, section 5.1.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern says:
====================
rtnetlink: Cleanup user notifications for netdev events
Vlad's recent patch to add the event type to rtnetlink notifications
points out a number of redundant or unnecessary notifications sent to
userspace for events that are essentially internal to the kernel. Trim
the list to put a dent in the notification storm.
v2
- rebased to top of net-next with IFLA_EVENT patch reverted
- dropped removal NETDEV_CHANGEINFODATA since it is intentionally
only to send a message to userspace
- dropped NOTIFY_PEERS since Vlad's says it is needed for macvlans
- add patches to remove NETDEV_CHANGEUPPER and NETDEV_CHANGE_TX_QUEUE_LEN
from the event list
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
NETDEV_CHANGEUPPER is an internal event; do not generate userspace
notifications.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CHANGELOWERSTATE is an internal event; do not generate userspace
notifications.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PRECHANGEUPPER is an internal event; do not generate userspace
notifications.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing the master device for a link generates many messages; the one
generated for POST_TYPE_CHANGE is redundant:
[LINK]11: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue master br1 state UNKNOWN group default
link/ether 02:02:02:02:02:03 brd ff:ff:ff:ff:ff:ff
[LINK]11: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue master br1 state UNKNOWN group default
link/ether 02:02:02:02:02:03 brd ff:ff:ff:ff:ff:ff
Remove POST_TYPE_CHANGE from the list of notifiers that generate
notifications.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing hardware address generates redundant messages:
[LINK]11: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default
link/ether 02:02:02:02:02:02 brd ff:ff:ff:ff:ff:ff
[LINK]11: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default
link/ether 02:02:02:02:02:02 brd ff:ff:ff:ff:ff:ff
Do not send a notification for the CHANGEADDR notifier.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NETDEV_UDP_TUNNEL_PUSH_INFO is an internal notifier; nothing userspace
can do so don't generate a netlink notification.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing MTU on a link currently causes 3 messages to be sent to userspace:
[LINK]11: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1490 qdisc noqueue state UNKNOWN group default
link/ether f2:52:5c:6d:21:f3 brd ff:ff:ff:ff:ff:ff
[LINK]11: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default
link/ether f2:52:5c:6d:21:f3 brd ff:ff:ff:ff:ff:ff
[LINK]11: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default
link/ether f2:52:5c:6d:21:f3 brd ff:ff:ff:ff:ff:ff
Remove the messages sent for PRE_CHANGE_MTU and CHANGE_MTU netdev events.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev field of struct fujitsu_bl is assigned in acpi_fujitsu_bl_add(),
but never used afterwards. brightness_changed is set in get_lcd_level()
and then its value is only printed in a debug message, so it does not
influence execution flow. Remove both fields as they are redundant.
Update the aforementioned debug message. Adjust whitespace to make
checkpatch happy.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
The comment for the get_brightness backlight device callback in
include/linux/backlight.h states that it should "return the current
backlight brightness (accounting for power, fb_blank etc.)".
fujitsu-laptop violates that premise by simply returning the value to
which ACPI function GBLL evaluates to. Make sure 0 is returned when
backlight power is turned off.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Any set_lcd_level() call can fail for one of two reasons: either
requested brightness is outside the allowed range or the ACPI method
used for setting brightness level is not available. For
bl_update_status(), the first case is handled by backlight core, which
means bl_update_status() will not even be called if requested brightness
is outside the allowed range. The second case will be logged anyway by
set_lcd_level() itself, so there is no point in generating another
message in bl_update_status(). Remove the superfluous debug message
along with a local variable that is now redundant.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Not all Fujitsu laptops support controlling backlight power through the
FUJ02E3 ACPI device. Remove the debug message informing about a failed
attempt to set backlight power as it may be confusing and the return
value of call_fext_func() is logged anyway.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Due to the way the disable_brightness_adjust module parameter is
currently handled in acpi_fujitsu_bl_add(), it can only be set to either
0 or 1, which effectively makes it a boolean. Emphasize that by
changing module parameter type to bool. Do not announce parameter value
in a debug message as it can be dynamically changed via sysfs and its
current value can also be read from there. Clean up module parameter
description.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
The value of each module parameter can be changed on the fly via sysfs.
However, the current way of handling use_alt_lcd_levels prevents the
user from dynamically switching from a value of 0 or 1 back to
autodetection as the latter is only performed upon ACPI device
instantiation. Fix this by moving autodetection (in a simplified form)
to set_lcd_level() and changing module parameter type to int. Do not
announce autodetection results in a debug message as current value of
use_alt_lcd_levels can simply be read from sysfs. Clarify module
parameter description.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
When using brightness keys and backlight device's sysfs interface
alternately, an incorrect input event might be generated for a
brightness key press. Consider the following sequence of events:
1. Set backlight brightness to 6 using brightness keys.
2. Write 4 to /sys/class/backlight/fujitsu-laptop/brightness.
3. Press the "brightness up" key.
The input event generated in this scenario would be KEY_BRIGHTNESSDOWN,
because before step 3 brightness_level would still be at 6. As the new
brightness level is established using GBLL, it would evaluate to 5
(SBLL/SBL2 sets it to 4 in step 2 and pressing the "brightness up" key
increases it by 1). This in turn would cause acpi_fujitsu_bl_notify()
to observe a 6 -> 5 change, i.e. a decrease in brightness, while screen
brightness would in fact be increased.
Fix this by updating brightness_level in set_lcd_level.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
acpi_execute_simple_method() takes a method parameter which tells it to
look for the given method underneath the given handle, so calling
acpi_get_handle() beforehand is redundant. Replace the call to
acpi_get_handle() with a call to acpi_execute_simple_method(), thus
eliminating the need for a local variable storing the handle. Update
debug message to reflect this change. Also do not assign a default
value to status as it has no influence on execution flow.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Depending on the value of the use_alt_lcd_levels module parameter, one
of two functions is used for setting LCD brightness level. These
functions are almost identical and only differ in the name of the ACPI
method they call. Instead of checking the value of use_alt_lcd_levels
at each call site, move that check to set_lcd_level() and get rid of
set_lcd_level_alt().
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Use a managed backlight device to get rid of acpi_fujitsu_bl_remove().
Change the parent of the backlight device from NULL to the FUJ02B1 ACPI
device as the latter is required for the backlight device to work.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
The backlight part of fujitsu-laptop is only used by laptops which are
incapable of using the standard ACPI video interface for handling
brightness changes. Conversely, on laptops which are capable of using
the latter, no vendor-specific ACPI calls should be made unless
explicitly requested by the user. Bail out immediately from
acpi_fujitsu_bl_add() unless using the vendor-specific interface was
either explicitly requested by the user or automatically selected by the
kernel.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
