Commit 1abf71e moved the creation of new_smi->dev to earlier in the init
sequence in order to provide infrastructure for log printing.
However, the init_name was created with a hard-coded value of zero. This
presents a problem in systems with more than one interface, producing a
call trace in dmesg.
To correct the problem, simply use smi_num instead of the hard-coded
value of zero.
Tested on a lenovo x3950.
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
There was actually a more general problem, the platform device wasn't
being set correctly, either, and there was a possible (though extremely
unlikely) race on smi_num. Add locks to clean up the race and use the
proper value for the platform device, too.
Tested on qemu in various configurations.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
We need to set "first = 0' at the end of rdev_for_each
loop, so we can get the array's min_offset_diff correctly
otherwise min_offset_diff just means the last rdev's
offset diff.
Suggested-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
To let userspace propagate formats downstream in a media controller
scenario, the video source pad (now pad 1, DEMOD_PAD_VID_OUT) must allow
setting and getting the format. Incidentally, tvp5150_fill_fmt was
implemented for this pad, not for the new analog input pad (now pad 0,
DEMOD_PAD_IF_INPUT).
Fixes: 55606310e7 ("[media] tvp5150: create the expected number of pads")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The call to v4ls_m2m_get_vq is only used to get the return value
which is not being used, so it appears to be redundant and can
be removed.
Detected with CoverityScan, CID#1420674 ("Useless call")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When recoverying a single missing/failed device in a RAID6,
those stripes where the Q block is on the missing device are
handled a bit differently. In these cases it is easy to
check that the P block is correct, so we do. This results
in the P block be destroy. Consequently the P block needs
to be read a second time in order to compute Q. This causes
lots of seeks and hurts performance.
It shouldn't be necessary to re-read P as it can be computed
from the DATA. But we only compute blocks on missing
devices, since c337869d95 ("md: do not compute parity
unless it is on a failed drive").
So relax the change made in that commit to allow computing
of the P block in a RAID6 which it is the only missing that
block.
This makes RAID6 recovery run much faster as the disk just
"before" the recovering device is no longer seeking
back-and-forth.
Reported-by-tested-by: Brad Campbell <lists2009@fnarfbargle.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
The em28xx driver still used the soc_camera.h header for the ov2640
driver. Since this driver no longer uses soc_camera, that include can
be removed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The MC support is needed by the em28xx driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The resource control filesystem provides only a bitmask based cpus file for
assigning CPUs to a resource group. That's cumbersome with large cpumasks
and non-intuitive when modifying the file from the command line.
Range based cpu lists are commonly used along with bitmask based cpu files
in various subsystems throughout the kernel.
Add 'cpus_list' file which is CPU range based.
# cd /sys/fs/resctrl/
# echo 1-10 > krava/cpus_list
# cat krava/cpus_list
1-10
# cat krava/cpus
0007fe
# cat cpus
fffff9
# cat cpus_list
0,3-23
[ tglx: Massaged changelog and replaced "bitmask lists" by "CPU ranges" ]
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Shaohua Li <shli@fb.com>
Link: http://lkml.kernel.org/r/20170410145232.GF25354@krava
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Convert v4l2_clk to normal clk and enable the clock.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Convert ov2640 to a standard subdev driver. The soc-camera driver no longer
uses this driver, so it can safely be converted.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The kernel-doc is inconsistently formatted. Fix it up.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vikas Shivappa <vikas.shivappa@linux.intel.com>
The vsyscall32 sysctl can racy against a concurrent fork when it switches
from disabled to enabled:
arch_setup_additional_pages()
if (vdso32_enabled)
--> No mapping
sysctl.vsysscall32()
--> vdso32_enabled = true
create_elf_tables()
ARCH_DLINFO_IA32
if (vdso32_enabled) {
--> Add VDSO entry with NULL pointer
Make ARCH_DLINFO_IA32 check whether the VDSO mapping has been set up for
the newly forked process or not.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mathias Krause <minipli@googlemail.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20170410151723.602367196@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
vdso_enabled can be set to arbitrary integer values via the kernel command
line 'vdso32=' parameter or via 'sysctl abi.vsyscall32'.
load_vdso32() only maps VDSO if vdso_enabled == 1, but ARCH_DLINFO_IA32
merily checks for vdso_enabled != 0. As a consequence the AT_SYSINFO_EHDR
auxiliary vector for the VDSO_ENTRY is emitted with a NULL pointer which
causes a segfault when the application tries to use the VDSO.
Restrict the valid arguments on the command line and the sysctl to 0 and 1.
Fixes: b0b49f2673 ("x86, vdso: Remove compat vdso support")
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org
Cc: Roland McGrath <roland@redhat.com>
Link: http://lkml.kernel.org/r/1491424561-7187-1-git-send-email-minipli@googlemail.com
Link: http://lkml.kernel.org/r/20170410151723.518412863@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
ISL9305_MAX_REGULATOR is the last index used to access the init_data[]
array, so we need to add one to this last index to obtain the necessary
array size.
This fixes the following smatch error:
drivers/regulator/isl9305.c:160 isl9305_i2c_probe() error: buffer overflow 'pdata->init_data' 3 <= 3
Fixes: dec38b5ce6 ("regulator: isl9305: Add Intersil ISL9305/H driver")
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The output voltage of a voltage controlled regulator can be controlled
through the voltage of another regulator. The current version of this
driver assumes that the output voltage is a linear function of the control
voltage.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We only need to have MFD_CPCAP and CPCAP_REGULATOR as built-in to
be able to mount root on the eMMC. And then POWER_RESET_GPIO
is good to have built-in. The rest of the devices can be loadable
modules.
This gets various devices such as regulators, touchscreen, power
button, HDMI audio, LEDs, RTC, and ADC working.
Note that omapdrm needs to be configured manually as we're still
using omapfb by default.
Signed-off-by: Tony Lindgren <tony@atomide.com>
It is a bit confusing how CEC_CAP_RC and IS_REACHABLE(CONFIG_RC_CORE)
interact. By stripping CEC_CAP_RC at the beginning rather than after #else
it should be a bit clearer what is going on.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently when the RC Core is enabled (reachable) core code located
in cec_register_adapter() attempts to populate the RC structure with
a pointer to the 'parent' passed in by the caller.
Unfortunately if the caller did not specify RC capability when calling
cec_allocate_adapter(), then there will be no RC structure to populate.
This causes a "NULL pointer dereference" error.
Fixes: f51e80804f ("[media] cec: pass parent device in register(), not allocate()")
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: <stable@vger.kernel.org> # for v4.10 and up
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
By using the CEC notifier framework there is no longer any reason
to manually set the physical address. This was the one blocking
issue that prevented this driver from going out of staging, so do
this move as well.
Update the bindings documenting the new hdmi phandle and
update exynos4.dtsi accordingly.
Tested with my Odroid U3.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
CC: linux-samsung-soc@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Update the bindings documenting the new hdmi phandle.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
CC: linux-samsung-soc@vger.kernel.org
CC: devicetree@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add the new hdmi phandle to exynos4.dtsi. This phandle is needed by the
s5p-cec driver to initialize the CEC notifier framework.
Tested with my Odroid U3.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: linux-samsung-soc@vger.kernel.org
CC: devicetree@vger.kernel.org
CC: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Implement the CEC notifier support to allow CEC drivers to
be informed when there is a new physical address.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
To use CEC notifier sti CEC driver needs to get phandle
of the hdmi device.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
CC: Patrice CHOTARD <patrice.chotard@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
By using the CEC notifier framework there is no longer any reason
to manually set the physical address. This was the one blocking
issue that prevented this driver from going out of staging, so do
this move as well.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Update the bindings documentation with the new hdmi phandle.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Implement the CEC notifier support to allow CEC drivers to
be informed when there is a new physical address.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Support the CEC notifier framework, simplifying drivers that
depend on this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for CEC notifiers, which is used to convey CEC physical address
information from video drivers to their CEC counterpart driver(s).
Based on an earlier version from Russell King:
https://patchwork.kernel.org/patch/9277043/
The cec_notifier is a reference counted object containing the CEC physical address
state of a video device.
When a new notifier is registered the current state will be reported to
that notifier at registration time.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Another preliminary patch for the dual-codec support: since the
support of vmaster over multiple codecs is difficult, simply disable
it by a new flag to hda_codec struct. A new user hint is added as
well for consistency.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a preliminary patch for a smooth multi-codec support, and it
introduces a new flag, force_pin_prefix, to struct hda_codec.
This flag is used to force to add the pin location prefix to each
input pin. For example, when there is only one microphone pin,
usually the auto-parser assigns the string "Mic". With this flag on,
it'll be like "Front Mic". Also, the creation of "Master" or "PCM"
playback volume for a single pin is suppressed, too.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=195305
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pointer to ->free_mark callback unnecessarily occupies one long in each
fsnotify_mark although they are the same for all marks from one
notification group. Move the callback pointer to fsnotify_ops.
Reviewed-by: Miklos Szeredi <mszeredi@redhat.com>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Currently we initialize mark->group only in fsnotify_add_mark_lock().
However we will need to access fsnotify_ops of corresponding group from
fsnotify_put_mark() so we need mark->group initialized earlier. Do that
in fsnotify_init_mark() which has a consequence that once
fsnotify_init_mark() is called on a mark, the mark has to be destroyed
by fsnotify_put_mark().
Reviewed-by: Miklos Szeredi <mszeredi@redhat.com>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
inode_mark.c now contains only a single function. Move it to
fs/notify/fsnotify.c and remove inode_mark.c.
Reviewed-by: Miklos Szeredi <mszeredi@redhat.com>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
These are very thin wrappers, just remove them. Drop
fs/notify/vfsmount_mark.c as it is empty now.
Reviewed-by: Miklos Szeredi <mszeredi@redhat.com>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
The function is already mostly contained in what
fsnotify_clear_marks_by_group() does. Just update that function to not
select marks when all of them should be destroyed and remove
fsnotify_detach_group_marks().
Reviewed-by: Miklos Szeredi <mszeredi@redhat.com>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
The _flags() suffix in the function name was more confusing than
explaining so just remove it. Also rename the argument from 'flags' to
'type' to better explain what the function expects.
Reviewed-by: Miklos Szeredi <mszeredi@redhat.com>
Suggested-by: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Inline these helpers as they are very thin. We still keep them as we
don't want to expose details about how list type is determined.
Reviewed-by: Miklos Szeredi <mszeredi@redhat.com>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
These helpers are just very thin wrappers now. Remove them.
Reviewed-by: Miklos Szeredi <mszeredi@redhat.com>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
These helpers are now only a simple assignment and just obfuscate
what is going on. Remove them.
Reviewed-by: Miklos Szeredi <mszeredi@redhat.com>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
When userspace task processing fanotify permission events screws up and
does not respond, fsnotify_mark_srcu SRCU is held indefinitely which
causes further hangs in the whole notification subsystem. Although we
cannot easily solve the problem of operations blocked waiting for
response from userspace, we can at least somewhat localize the damage by
dropping SRCU lock before waiting for userspace response and reacquiring
it when userspace responds.
Reviewed-by: Miklos Szeredi <mszeredi@redhat.com>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Pass fsnotify_iter_info into ->handle_event() handler so that it can
release and reacquire SRCU lock via fsnotify_prepare_user_wait() and
fsnotify_finish_user_wait() functions. These functions also make sure
current marks are appropriately pinned so that iteration protected by
srcu in fsnotify() stays safe.
Reviewed-by: Miklos Szeredi <mszeredi@redhat.com>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
fanotify wants to drop fsnotify_mark_srcu lock when waiting for response
from userspace so that the whole notification subsystem is not blocked
during that time. This patch provides a framework for safely getting
mark reference for a mark found in the object list which pins the mark
in that list. We can then drop fsnotify_mark_srcu, wait for userspace
response and then safely continue iteration of the object list once we
reaquire fsnotify_mark_srcu.
Reviewed-by: Miklos Szeredi <mszeredi@redhat.com>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Currently we queue all marks for destruction on group shutdown and then
destroy them from fsnotify_destroy_group() instead from a worker thread
which is the usual path. However worker can already be processing some
list of marks to destroy so this does not make 100% all marks are really
destroyed by the time group is shut down. This isn't a big problem as
each mark holds group reference and thus group stays partially alive
until all marks are really freed but there's no point in complicating
our lives - just wait for the delayed work to be finished instead.
Reviewed-by: Miklos Szeredi <mszeredi@redhat.com>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
