The function probe counting for traceon and traceoff suffered a race
condition where if the probe was executing on two or more CPUs at the
same time, it could decrement the counter by more than one when
disabling (or enabling) the tracer only once.
The way the traceon and traceoff probes are suppose to work is that
they disable (or enable) tracing once per count. If a user were to
echo 'schedule:traceoff:3' into set_ftrace_filter, then when the
schedule function was called, it would disable tracing. But the count
should only be decremented once (to 2). Then if the user enabled tracing
again (via tracing_on file), the next call to schedule would disable
tracing again and the count would be decremented to 1.
But if multiple CPUS called schedule at the same time, it is possible
that the count would be decremented more than once because of the
simple "count--" used.
By reading the count into a local variable and using memory barriers
we can guarantee that the count would only be decremented once per
disable (or enable).
The stack trace probe had a similar race, but here the stack trace will
decrement for each time it is called. But this had the read-modify-
write race, where it could stack trace more than the number of times
that was specified. This case we use a cmpxchg to stack trace only the
number of times specified.
The dump probes can still use the old "update_count()" function as
they only run once, and that is controlled by the dump logic
itself.
Link: http://lkml.kernel.org/r/20141118134643.4b550ee4@gandalf.local.home
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The locked page should be released before returning the function.
Reviewed-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
The LEDs on the kzm9g board are labeled using upper-case characters.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The LEDs on the koelsch board are labeled using upper-case characters.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The IIC nodes used the generic compatible properties only.
This causes the driver to fail when using Standard Speed, as the
operational clock is driven by the 104 MHz HP clock:
i2c-sh_mobile e6820000.i2c: timing values out of range: L/H=0x208/0x1bf
i2c-sh_mobile: probe of e6820000.i2c failed with error -22
Add the SoC-specific compatible property to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The IIC nodes used the generic compatible properties only.
This may cause the driver to fail when using Standard Speed on IIC
masters where the operational clock is driven by the 130 MHz HP clock.
Add the SoC-specific compatible property to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Current Koelsch I2C2 has 400kHz settings,
but, ak4643 audio codec chip which is connected to I2C2 can't
work such frequency.
Fixup I2C2 clock frequency to 100kHz.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Current Lager IIC2 is using default clock frequency,
but, ak4643 audio codec chip needs 100kHz
This patch clarifies IIC2 clock frequency as 100kHz.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The number of and dependencies between high-level power management
Kconfig options make life much harder than necessary. Several
conbinations of them have to be tested and supported, even though
some of those combinations are very rarely used in practice (if
they are used in practice at all). Moreover, the fact that we
have separate independent Kconfig options for runtime PM and
system suspend is a serious obstacle for integration between
the two frameworks.
To overcome these difficulties, always select PM_RUNTIME if PM_SLEEP
is set. Among other things, this will allow system suspend callbacks
provided by bus types and device drivers to rely on the runtime PM
framework regardless of the kernel configuration.
Enthusiastically-acked-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The commit 5935839ad7
"mac80211: improve minstrel_ht rate sorting by throughput & probability"
introduced a crash on rate sorting that occurs when the rate added to
the sorting array is faster than all the previous rates. Due to an
off-by-one error, it reads the rate index from tp_list[-1], which
contains uninitialized stack garbage, and then uses the resulting index
for accessing the group rate stats, leading to a crash if the garbage
value is big enough.
Cc: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Report is received in "buffer"; fix the following i2c_hid_dbg()
to dump data from the correct pointer.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
[Antonio Borneo: cleanup and rebase to v3.17]
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The only reason gb_operation_message_init() gets its "outbound"
argument is so we can determine what allocation flags to use.
Just pass the flags in directly instead.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
We can derive the destination CPort id of any (outbound) message
from the connection it's operation is associated with. So we don't
need to store that information in every message.
As a result, we no longer need to record it at message initialization
time.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
The host device pointer doesn't have to be stored in every message.
It can be derived by following up the chain of pointers back to
the operation's connection.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
All the code has now been adjusted such that we can do away with the
old gbuf structure.
Three unused references remained in "greybus.h", so those are deleted.
Other than that most of the changes were done by simple global
substitution. The gb_message structure incorporates the fields that
were previously found its embedded gbuf structure. A few names have
been changed in the process:
gbuf->transfer_buffer message->buffer
gbuf->transfer_buffer_size message->buffer_size
gbuf->hcd_data; message->cookie
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
Rework gb_connection_operation_recv() to be more oriented toward an
operation message, and to no longer use a struct gbuf local variable.
Rename it to be a little more wieldy.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
Rework greybus_kill_gbuf() to be oriented toward an operation
message rather than a gbuf, and rename it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
Rework greybus_submit_gbuf() to be oriented toward an operation
message rather than a gbuf, and rename it accordingly.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
Rework gb_opreation_message_init() so it doesn't use a struct gbuf
local variable.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
Change the method that sends messages so that it sends "raw" buffers
rather than gbufs. To do this, we supply the host device and
destination CPort when sending. As with other recent patches,
change the name of the method to reflect that we're no longer
dealing with gbufs.
The interface has changed as well. Now this routine will return a
"cookie" value. The cookie is used to represent the outgoing
request, and is supplied by the caller if necessary to cancel a
previously-sent buffer. We'll store the result in gbuf->hcd_data
for now (which produces the same result as before...).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
This changes the context value stashed with each USB URB so that it
is always the host device pointer.
In cport_out_callback() this allows us to get away with *not*
requiring the gbuf for handling completions any more. We are
(currently) ignoring the gbuf status value returned anyway, so
we'll skip setting it altogether.
Greg's comments in cport_out_callback() point out that ignoring
this was misguided, and handling send errors will be put in
place in an upcoming patch.
The context is set to the host device pointer for SVC receive and
CPort receive URBs for consistency--because we can.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
Change the interface for canceling in-flight buffers to take a magic
cookie value as argument rather than a gbuf. Right now we pass the
gbuf->hcd_data pointer that's assumed to have been set by the submit
routine. But the next patch will change the submit routine to
return the cookie to be used, and the caller will be responsible for
keeping track of it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
Switch the host driver free routine to take a pointer to the
previously-allocated buffer that should be freed.
Rename the method to reflect it's no longer tied to a gbuf.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
This begins the transition to buffer allocation that does not rely
on the gbuf construct.
The host driver allocation routine will return a pointer to the
buffer to be used, and the caller will be responsible for keeping
track of that pointer, as well as the requested buffer size.
Rename the allocation method to reflect it's no longer tied to a
gbuf.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
For ES1 we need to insert the destination CPort id before the data
to be sent over UniPro. Currently this is done at the time the
buffer is created, but there's no need to do so until we're actually
going to send the content of the buffer.
Move the setting of that destination information into submit_gbuf().
Note that this allows us to defer initializing a few other gbuf
fields until after we know the buffer allocation has succeeded.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
For ES1 we need to insert the destination CPort id in whatever we
supply for sending over UniPro. Currently we allocate one extra
byte supply the caller with an address that's offset by one from
the beginning of the allocated space.
As a result we always return a poorly-aligned buffer pointer.
Instead, allocate enough space so that we can return a better
aligned buffer to the caller.
Notes:
- It may be that it's more important to supply an aligned
address to the hardware.
- We probably need to be more careful about writing into
these buffers at unaligned offsets anyway. (E.g., writing
a 2-byte value at an odd offset can't be assumed to work.)
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
Treat communication buffers for both inbound and outbound data the
same way, prepending a "destination cport id" byte before the data
in the buffer. Currently this is done only for outbound data
buffers.
This isn't needed for inbound data, but handling it this way
allows the free routine to work without knowing whether the
buffer was used for sending or receiving.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
We allocate message buffers with GFP_KERNEL allocation flags if
possible. However when an incoming request message is received we
can be in interrupt context, so we must use GFP_ATOMIC in that case.
The computation of gfp_flags in gb_operation_message_init() is
wrong. It is needlessly using GFP_ATOMIC when allocating outbound
response buffers. Fix the flawed logic.
Change the name of "data_out" to be "outbound" to be consistent with
usage elsewhere. (Data/messages are "inbound" or "outbound";
requests are "incoming" or "outgoing".)
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
Suggested-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>