Commit graph

691,473 commits

Author SHA1 Message Date
Peter Griffin
6919edc84c ARM: STi: DT: Enable mmc0 for both stih415 and stih416 SoCs
Because the first sdhci controller is present on both stih415 and
stih416 SoC which can both populate the b2020 board, it can be
enabled in the generic DT file.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
2014-10-31 09:59:03 +01:00
Peter Griffin
7b40c726b1 ARM: STi: DT: Add sdhci controller for stih415
This patch adds device tree config for the sdhci controller
on the stih415 SoC.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
2014-10-31 09:59:02 +01:00
Peter Griffin
14304e0056 ARM: STi: DT: Add sdhci pin configuration for stih415
This patch adds the required pin config for the sdhci controller
present in the stih415 SoC.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
2014-10-31 09:59:02 +01:00
Peter Griffin
42d6f28d64 ARM: STi: DT: Add sdhci controller for stih416
This patch adds device tree config for both sdhci controllers
on the stih416 SoC.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
2014-10-31 09:59:01 +01:00
Peter Griffin
8106d21ca8 ARM: STi: DT: Add sdhci pins for stih416
This adds the required pin config for both SDHCI controllers on
the stih416 SoC.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
2014-10-31 09:59:00 +01:00
Peter Griffin
b864a0b98e ARM: sti: Add STiH407 reset controller support.
This patch adds the reset controller DT nodes for the powerdown,
 softreset and picophy controllers.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
2014-10-31 09:58:59 +01:00
Peter Griffin
c273211419 ARM: sti: Add STiH407 Kconfig entry to select STIH407_RESET
The STiH407 is a STMicroelectronics Digital Consumer electronics
family, targetted at set-top-box and other audio/video applications.

This patch selects the reset controller driver for this family which
is essential to take various IP's on the SoC out of powerdown / reset.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
2014-10-31 09:58:58 +01:00
Lee Jones
dc62bfdfa3 ARM: STi: DT: STiH41x: Convert all uppercase non-defines to lowercase
Suggested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
2014-10-31 09:58:57 +01:00
Sinclair Yeh
9a72384d86 drm/vmwgfx: Filter out modes those cannot be supported by the current VRAM size.
When screen objects are enabled, the bpp is assumed to be 32, otherwise
it is set to 16.

v2:
* Use u32 instead of u64 for assumed_bpp.
* Fixed mechanism to check for screen objects
* Limit the back buffer size to VRAM.

Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Cc: <stable@vger.kernel.org>
2014-10-31 09:58:06 +01:00
Thomas Hellstrom
0468ab5b79 drm/vmwgfx: Fix hash key computation
The hash key computation in vmw_cmdbuf_res_remove incorrectly didn't take
the resource type into account, contrary to all the other related functions.
This becomes important when the cmdbuf resource manager handles more than
one resource type.

Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
2014-10-31 09:54:22 +01:00
Maxime Coquelin
c759e5f76b reset: stih407: Add reset controllers DT bindings
This patch adds softreset, powerdown and picophy reset controllers
DT bindings for the STiH407 SoC.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
2014-10-31 09:47:54 +01:00
Rob Clark
21e88620aa drm/vmwgfx: fix lock breakage
After:

commit d059f652e7
Author:     Daniel Vetter <daniel.vetter@ffwll.ch>
AuthorDate: Fri Jul 25 18:07:40 2014 +0200

    drm: Handle legacy per-crtc locking with full acquire ctx

drm_mode_cursor_common() was switched to use drm_modeset_(un)lock_crtc()
which uses full aquire ctx.  So dropping/reaquiring the lock via
drm_modeset_(un)lock() directly isn't the right thing to do, as lockdep
kindly points out.

The 'FIXME's about sorting out whether vmwgfx *really* needs to lock-all
for cursor updates still apply.

Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Tested-by: Thomas Hellstrom <thellstrom@vmware.com>
2014-10-31 09:44:35 +01:00
Takashi Iwai
4c41421657 Merge branch 'topic/kerneldoc' into for-next 2014-10-31 09:31:06 +01:00
Johannes Berg
de29eda892 mac80211-hwsim: add missing policy entries
A few recent additions to the netlink attributes neglected
to add policy entries, fix that now.

Reported-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-10-31 09:26:06 +01:00
Chen-Yu Tsai
fec99debbc ARM: dts: sun9i: Enable uart4 for A80 Optimus board
The A80 Optimus board exposes uart4 on the GPIO expansion header.
Enable it so we can use it.

Also enable the internal pull-ups, as there doesn't seem to be
external pull-up resistors for pins on the expansion header.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2014-10-31 09:25:52 +01:00
Chen-Yu Tsai
2a950b2ca0 ARM: dts: sun9i: Add uart4 pinmux setting for A80 SoC
uart4 only has one possible pinmux setting on the A80 SoC.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2014-10-31 09:25:41 +01:00
Chen-Yu Tsai
0cc4539901 ARM: dts: sun9i: Add GPIO LEDs for A80 Optimus board
The A80 Optimus board has 3 usable LEDs that are controlled via GPIO.

This patch adds support for 2 of them which are driver by GPIOs in the
main pin controller. The remaining one uses GPIO from the R_PIO
controller, which we don't support yet.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2014-10-31 09:25:37 +01:00
Chen-Yu Tsai
475c6285cf ARM: dts: sun9i: Enable i2c3 on A80 Optimus board
i2c3 is exposed on the GPIO extension header. Enable it so we can use it.

Also enable internal pull-ups on the pins, as they don't seem to have
external pull-up resistors.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2014-10-31 09:25:19 +01:00
Chen-Yu Tsai
6657a05872 ARM: dts: sun9i: Add i2c3 pinmux setting for A80 SoC
i2c3 has only one possible pinmux setting on the A80 SoC.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2014-10-31 09:25:11 +01:00
Chen-Yu Tsai
e4aa753a72 ARM: dts: sun9i: Add i2c controller nodes to a80 dtsi
The A80 has 5 i2c controllers in the main processor block.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2014-10-31 09:25:01 +01:00
Varka Bhadram
5bb5428956 gpio: gpio-davinci: remove duplicate check on resource
Sanity check on resource happening with devm_ioremap_resource().

Signed-off-by: Varka Bhadram <varkab@cdac.in>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-10-31 09:02:34 +01:00
Stephen Hemminger
d070f9137a mac80211: fix spelling errors
Use codespell to find spelling errors.

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-10-31 08:29:56 +01:00
Benjamin Herrenschmidt
325e411404 powerpc/powernv: Properly fix LPC debugfs endianness
Endian is hard, especially when I designed a stupid FW interface, and
I should know better... oh well, this is attempt #2 at fixing this
properly. This time it seems to work with all access sizes and I
can run my flashing tool (which exercises all sort of access sizes
and types to access the SPI controller in the BMC) just fine.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: stable@vger.kernel.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2014-10-31 17:09:04 +11:00
Anton Blanchard
808be31426 powerpc: do_notify_resume can be called with bad thread_info flags argument
Back in 7230c56441 ("powerpc: Rework lazy-interrupt handling") we
added a call out to restore_interrupts() (written in c) before calling
do_notify_resume:

        bl      restore_interrupts
        addi    r3,r1,STACK_FRAME_OVERHEAD
        bl      do_notify_resume

Unfortunately do_notify_resume takes two arguments, the second one
being the thread_info flags:

void do_notify_resume(struct pt_regs *regs, unsigned long thread_info_flags)

We do populate r4 (the second argument) earlier, but
restore_interrupts() is free to muck it up all it wants. My guess is
the gcc compiler gods shone down on us and its register allocator
never used r4. Sometimes, rarely, luck is on our side.

LLVM on the other hand did trample r4.

Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2014-10-31 16:52:46 +11:00
Ben Hutchings
de11b0e8c5 drivers/net: macvtap and tun depend on INET
These drivers now call ipv6_proxy_select_ident(), which is defined
only if CONFIG_INET is enabled.  However, they have really depended
on CONFIG_INET for as long as they have allowed sending GSO packets
from userland.

Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: f43798c276 ("tun: Allow GSO using virtio_net_hdr")
Fixes: b9fb9ee07e ("macvtap: add GSO/csum offload support")
Fixes: 5188cd44c5 ("drivers/net, ipv6: Select IPv6 fragment idents for virtio UFO packets")
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-30 23:50:26 -04:00
Rabin Vincent
086ba77a6d tracing/syscalls: Ignore numbers outside NR_syscalls' range
ARM has some private syscalls (for example, set_tls(2)) which lie
outside the range of NR_syscalls.  If any of these are called while
syscall tracing is being performed, out-of-bounds array access will
occur in the ftrace and perf sys_{enter,exit} handlers.

 # trace-cmd record -e raw_syscalls:* true && trace-cmd report
 ...
 true-653   [000]   384.675777: sys_enter:            NR 192 (0, 1000, 3, 4000022, ffffffff, 0)
 true-653   [000]   384.675812: sys_exit:             NR 192 = 1995915264
 true-653   [000]   384.675971: sys_enter:            NR 983045 (76f74480, 76f74000, 76f74b28, 76f74480, 76f76f74, 1)
 true-653   [000]   384.675988: sys_exit:             NR 983045 = 0
 ...

 # trace-cmd record -e syscalls:* true
 [   17.289329] Unable to handle kernel paging request at virtual address aaaaaace
 [   17.289590] pgd = 9e71c000
 [   17.289696] [aaaaaace] *pgd=00000000
 [   17.289985] Internal error: Oops: 5 [#1] PREEMPT SMP ARM
 [   17.290169] Modules linked in:
 [   17.290391] CPU: 0 PID: 704 Comm: true Not tainted 3.18.0-rc2+ #21
 [   17.290585] task: 9f4dab00 ti: 9e710000 task.ti: 9e710000
 [   17.290747] PC is at ftrace_syscall_enter+0x48/0x1f8
 [   17.290866] LR is at syscall_trace_enter+0x124/0x184

Fix this by ignoring out-of-NR_syscalls-bounds syscall numbers.

Commit cd0980fc8a "tracing: Check invalid syscall nr while tracing syscalls"
added the check for less than zero, but it should have also checked
for greater than NR_syscalls.

Link: http://lkml.kernel.org/p/1414620418-29472-1-git-send-email-rabin@rab.in

Fixes: cd0980fc8a "tracing: Check invalid syscall nr while tracing syscalls"
Cc: stable@vger.kernel.org # 2.6.33+
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
2014-10-30 20:58:38 -04:00
Michal Kazior
7962b0d898 ath10k: speed up hw recovery
In some cases hw recovery was taking an absurdly
long time due to ath10k waiting for things that
would never really complete.

Instead of waiting for inevitable timeouts poke
all completions and wakequeues and check if it's
still worth waiting.

Reading/writing ar->state requires conf_mutex.
Since waiters might be holding it introduce a new
flag CRASH_FLUSH so it's possible to tell waiters
to abort whatever they were waiting for.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-31 02:32:28 +02:00
Michal Kazior
605cdba1c9 ath10k: expose hw restart via debugfs
Until now it was possible to simulate soft and
hard fw crashes but it wasn't possible to trigger
an immediately hw restart itself (without the fw
crash).

This can be useful when stress testing hw
restarting stability, e.g. during heavy tx/rx
traffic.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-31 02:32:21 +02:00
Michal Kazior
04ed9dfe49 ath10k: fix possible bmi crash
While testing other things I've found that CE
items aren't cleared properly. This could lead to
null dereferences in BMI.

To prevent that make sure CE revoking clears the
nbytes value (which is used as a buffer completion
indication) and memset the entire CE ring data
shared between host and target when
(re)initializing.

Also make sure to check BMI xfer pointer and print
a splat instead of crashing the kernel.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-31 02:32:15 +02:00
Michal Kazior
c011b28159 ath10k: don't reset chip on power_down
Currently hif_power_up performs effectively a
reset and hif_stop resets the chip as well so
there's no point in resetting here.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-31 02:27:14 +02:00
Michal Kazior
0bc14d061b ath10k: split reset logic from power up
The power up procedure was overly complex due to
warm/cold reset workarounds and issues.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-31 02:27:06 +02:00
Michal Kazior
61c1648bd7 ath10k: make warm reset a bit safer and faster
One of the problems with warm reset I've found is
that it must be guaranteed that copy engine
registers are not being accessed while being
reset. Otherwise in worst case scenario the host
may lock up.

Instead of using sleeps and hoping the device is
operational in some arbitrary timeframes use
firmware indication register.

As a side effect this makes driver
boot/stop/recovery faster.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-31 02:26:59 +02:00
Michal Kazior
099ac7ce2e ath10k: change ce ring cleanup logic
Make ath10k_pci_init_pipes() effectively only
alter shared target-host data.

The per_transfer_context is a host-only thing.
It is necessary to preserve it's contents for a
more robust ring cleanup.

This is required for future warm reset fixes.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-31 02:26:48 +02:00
Michal Kazior
4eb2e16487 ath10k: avoid possible deadlock with scan timeout
This should prevent deadlock predicted by the
following splat:

 ======================================================
 [ INFO: possible circular locking dependency detected ]
 3.17.0-wl-ath+ #67 Not tainted
 -------------------------------------------------------
 kworker/u32:1/7230 is trying to acquire lock:
  (&ar->conf_mutex){+.+.+.}, at: [<ffffffffa040a57d>] ath10k_scan_timeout_work+0x2d/0x50 [ath10k_core]

 but task is already holding lock:
  ((&(&ar->scan.timeout)->work)){+.+...}, at: [<ffffffff8106dae1>] process_one_work+0x151/0x470

 which lock already depends on the new lock.

 the existing dependency chain (in reverse order) is:

 -> #1 ((&(&ar->scan.timeout)->work)){+.+...}:
        [<ffffffff810a12e5>] lock_acquire+0x85/0x100
        [<ffffffff8106cb4d>] flush_work+0x3d/0x270
        [<ffffffff8106e49d>] __cancel_work_timer+0x7d/0x110
        [<ffffffff8106e543>] cancel_delayed_work_sync+0x13/0x20
        [<ffffffffa0409f16>] ath10k_cancel_remain_on_channel+0x36/0x60 [ath10k_core]
        [<ffffffffa028c75c>] ieee80211_cancel_roc+0x1cc/0x2f0 [mac80211]
        [<ffffffffa028c8a2>] ieee80211_mgmt_tx_cancel_wait+0x22/0x30 [mac80211]
        [<ffffffffa0132288>] nl80211_tx_mgmt_cancel_wait+0xa8/0x130 [cfg80211]
        [<ffffffff816654a5>] genl_family_rcv_msg+0x1a5/0x3c0
        [<ffffffff81665749>] genl_rcv_msg+0x89/0xc0
        [<ffffffff81664e91>] netlink_rcv_skb+0xb1/0xc0
        [<ffffffff816650bc>] genl_rcv+0x2c/0x40
        [<ffffffff8166474d>] netlink_unicast+0x18d/0x200
        [<ffffffff81664add>] netlink_sendmsg+0x31d/0x430
        [<ffffffff8161a9ac>] sock_sendmsg+0x9c/0xd0
        [<ffffffff8161b469>] ___sys_sendmsg+0x389/0x3a0
        [<ffffffff8161bed9>] __sys_sendmsg+0x49/0x90
        [<ffffffff8161bf32>] SyS_sendmsg+0x12/0x20
        [<ffffffff8174c456>] system_call_fastpath+0x1a/0x1f

 -> #0 (&ar->conf_mutex){+.+.+.}:
        [<ffffffff810a0bde>] __lock_acquire+0x1b6e/0x1ce0
        [<ffffffff810a12e5>] lock_acquire+0x85/0x100
        [<ffffffff817491eb>] mutex_lock_nested+0x4b/0x370
        [<ffffffffa040a57d>] ath10k_scan_timeout_work+0x2d/0x50 [ath10k_core]
        [<ffffffff8106db41>] process_one_work+0x1b1/0x470
        [<ffffffff8106df63>] worker_thread+0x123/0x460
        [<ffffffff81073f34>] kthread+0xe4/0x100
        [<ffffffff8174c3ac>] ret_from_fork+0x7c/0xb0

 other info that might help us debug this:

  Possible unsafe locking scenario:

        CPU0                    CPU1
        ----                    ----
   lock((&(&ar->scan.timeout)->work));
                                lock(&ar->conf_mutex);
                                lock((&(&ar->scan.timeout)->work));
   lock(&ar->conf_mutex);

  *** DEADLOCK ***

Reported-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-31 02:16:30 +02:00
David S. Miller
c1304b217c Merge branch 'ufo-fix'
Ben Hutchings says:

====================
drivers/net,ipv6: Fix IPv6 fragment ID selection for virtio

The virtio net protocol supports UFO but does not provide for passing a
fragment ID for fragmentation of IPv6 packets.  We used to generate a
fragment ID wherever such a packet was fragmented, but currently we
always use ID=0!

v2: Add blank lines after declarations
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-30 20:01:27 -04:00
Ben Hutchings
5188cd44c5 drivers/net, ipv6: Select IPv6 fragment idents for virtio UFO packets
UFO is now disabled on all drivers that work with virtio net headers,
but userland may try to send UFO/IPv6 packets anyway.  Instead of
sending with ID=0, we should select identifiers on their behalf (as we
used to).

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: 916e4cf46d ("ipv6: reuse ip6_frag_id from ip6_ufo_append_data")
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-30 20:01:18 -04:00
Ben Hutchings
3d0ad09412 drivers/net: Disable UFO through virtio
IPv6 does not allow fragmentation by routers, so there is no
fragmentation ID in the fixed header.  UFO for IPv6 requires the ID to
be passed separately, but there is no provision for this in the virtio
net protocol.

Until recently our software implementation of UFO/IPv6 generated a new
ID, but this was a bug.  Now we will use ID=0 for any UFO/IPv6 packet
passed through a tap, which is even worse.

Unfortunately there is no distinction between UFO/IPv4 and v6
features, so disable UFO on taps and virtio_net completely until we
have a proper solution.

We cannot depend on VM managers respecting the tap feature flags, so
keep accepting UFO packets but log a warning the first time we do
this.

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: 916e4cf46d ("ipv6: reuse ip6_frag_id from ip6_ufo_append_data")
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-30 20:01:18 -04:00
Eric Dumazet
39bb5e6286 net: skb_fclone_busy() needs to detect orphaned skb
Some drivers are unable to perform TX completions in a bound time.
They instead call skb_orphan()

Problem is skb_fclone_busy() has to detect this case, otherwise
we block TCP retransmits and can freeze unlucky tcp sessions on
mostly idle hosts.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 1f3279ae0c ("tcp: avoid retransmits of TCP packets hanging in host queues")
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-30 19:58:30 -04:00
David S. Miller
f0c65567b3 Merge branch 'sunvnet-multi-tx-queue'
Sowmini Varadhan says:

====================
sunvnet: Use multiple Tx queues.

v2: moved tcp fix out of this series per David Miller feedback

The primary objective of this patch-set is to address the suggestion from
  http://marc.info/?l=linux-netdev&m=140790778931563&w=2
With the changes in Patch 2, every vnet_port will get  packets from
a single tx-queue, and flow-control/head-of-line-blocking is
confined to the vnet_ports that share that tx queue (as opposed to
flow-controlling *all* peers).

Patch 1 is an optimization that resets the DATA_READY bit when
we re-enable Rx interrupts.  This optimization lets us exit quickly
from vnet_event_napi() when new data has not triggered an interrupt.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-30 19:56:34 -04:00
Sowmini Varadhan
d51bffd16d sunvnet: Use one Tx queue per vnet_port
Use multple Tx netdev queues for sunvnet by supporting a one-to-one
mapping between vnet_port and Tx queue. Provide a ndo_select_queue
indirection (vnet_select_queue()) which selects the queue based
on the peer that would be selected in vnet_start_xmit()

Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-30 19:56:23 -04:00
Sowmini Varadhan
7bd68bfd51 sunvnet: Reset LDC_EVENT_DATA_READY when napi completes.
When vnet_event_napi re-enables interrupts, it should
reset LDC_EVENT_DATA_READY as an optimization.

Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-30 19:56:22 -04:00
Sowmini Varadhan
cd2145358e tcp: Correction to RFC number in comment
Challenge ACK is described in RFC 5961, fix typo.

Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-30 19:53:34 -04:00
Tom Herbert
14051f0452 gre: Use inner mac length when computing tunnel length
Currently, skb_inner_network_header is used but this does not account
for Ethernet header for ETH_P_TEB. Use skb_inner_mac_header which
handles TEB and also should work with IP encapsulation in which case
inner mac and inner network headers are the same.

Tested: Ran TCP_STREAM over GRE, worked as expected.

Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-30 19:51:56 -04:00
David S. Miller
292dd6542f Merge branch 'mellanox-net'
Or Gerlitz says:

====================
mlx4 driver encapsulation/steering fixes

The 1st patch fixes a bug in the TX path that supports offloading the
TX checksum of (VXLAN) encapsulated TCP packets. It turns out that the
bug is revealed only when the receiver runs in non-offloaded mode, so
we somehow missed it so far... please queue it for -stable >= 3.14

The 2nd patch makes sure not to leak steering entry on error flow,
please queue it to 3.17-stable
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-30 19:49:20 -04:00
Or Gerlitz
571e1b2c7a mlx4: Avoid leaking steering rules on flow creation error flow
If mlx4_ib_create_flow() attempts to create > 1 rules with the
firmware, and one of these registrations fail, we leaked the
already created flow rules.

One example of the leak is when the registration of the VXLAN ghost
steering rule fails, we didn't unregister the original rule requested
by the user, introduced in commit d2fce8a906 "mlx4: Set
user-space raw Ethernet QPs to properly handle VXLAN traffic".

While here, add dump of the VXLAN portion of steering rules
so it can actually be seen when flow creation fails.

Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-30 19:48:58 -04:00
Or Gerlitz
a4f2dacbf2 net/mlx4_en: Don't attempt to TX offload the outer UDP checksum for VXLAN
For VXLAN/NVGRE encapsulation, the current HW doesn't support offloading
both the outer UDP TX checksum and the inner TCP/UDP TX checksum.

The driver doesn't advertize SKB_GSO_UDP_TUNNEL_CSUM, however we are wrongly
telling the HW to offload the outer UDP checksum for encapsulated packets,
fix that.

Fixes: 837052d0cc ('net/mlx4_en: Add netdev support for TCP/IP
		     offloads of vxlan tunneling')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-30 19:48:58 -04:00
David S. Miller
9cc233fb0f Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net
Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2014-10-30

This series contains updates to e1000, igb and ixgbe.

Francesco Ruggeri fixes an issue with e1000 where in a VM the driver did
not support unicast filtering.

Roman Gushchin fixes an issue with igb where the driver was re-using
mapped pages so that packets were still getting dropped even if all
the memory issues are gone and there is free memory.

Junwei Zhang found where in the ixgbe_clean_rx_ring() we were repeating
the assignment of NULL to the receive buffer skb and fixes it.

Emil fixes a race condition between setup_link and SFP detection routine
in the watchdog when setting the advertised speed.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-30 19:46:33 -04:00
Richard Guy Briggs
897f1acbb6 audit: AUDIT_FEATURE_CHANGE message format missing delimiting space
Add a space between subj= and feature= fields to make them parsable.

Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paul Moore <pmoore@redhat.com>
2014-10-30 19:42:02 -04:00
Michele Baldessari
afb6befce6 sctp: replace seq_printf with seq_puts
Fixes checkpatch warning:
"WARNING: Prefer seq_puts to seq_printf"

Signed-off-by: Michele Baldessari <michele@acksyn.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-30 19:40:16 -04:00
Michele Baldessari
891310d53d sctp: add transport state in /proc/net/sctp/remaddr
It is often quite helpful to be able to know the state of a transport
outside of the application itself (for troubleshooting purposes or for
monitoring purposes). Add it under /proc/net/sctp/remaddr.

Signed-off-by: Michele Baldessari <michele@acksyn.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-30 19:40:16 -04:00