The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Serialize access to the hardware by using "request_muxed_region".
Call to this macro will hold off the requestor if the resource is
currently busy. "superio_enter" will return an error if call to
"request_muxed_region" fails.
Signed-off-by: Katsumi Sato <sato@toshiba-tops.co.jp>
Signed-off-by: Atsushi Nemoto <nemoto@toshiba-tops.co.jp>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch allows to avoid a transitory that occurs when a given sensor
has been already enabled (e.g. gyroscope) and the user is configuring
the sample frequency of the other one (e.g. accelerometer).
The transitory lasts until the accelerometer is enabled.
During that time slice the gyroscope ODR is incorrectly modified as well.
At the end of the transitory both sensors work at the right frequency.
Fix it introducing st_lsm6dsx_check_odr() routine to check ODR consistency
in write_raw handler in order to apply frequency configuration just
in st_lsm6dsx_set_odr()
Fixes: 290a6ce11d (iio: imu: add support to lsm6dsx driver)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When system bootup without get sensor property, set sensor
property will be fail.
If no get_feature operation done before set_feature, the sensor
properties will all be the initialized value, which is not the
same with sensor real properties. When set sensor property it will
write back to sensor the changed perperty data combines with other
sensor properties data, it is not right and may be dangerous.
In order to get all sensor properties, choose to read one of the sensor
properties(no matter read any sensor peroperty, driver will get all
the peroperties and return the requested one).
Fixes: 73c6768b71 ("iio: hid-sensors: Common attribute and trigger")
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
With CONFIG_THERMAL=m and CONFIG_SUN4I_GPADC=y, we get a link error
from calling devm_thermal_zone_of_sensor_register:
drivers/iio/built-in.o: In function `sun4i_gpadc_probe':
:(.text+0x1c284): undefined reference to `devm_thermal_zone_of_sensor_register'
This adds a Kconfig dependency to ensure we can only have the ADC
driver as built-in when this function is also built-in, or when
we see the empty stub implementation. When the thermal code is
a module, we can still build the adc driver as a module, too.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: d1caa99055 ("iio: adc: add support for Allwinner SoCs ADC")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When both accel_3d and gravity sensor are present, iio_device_register()
fails with "Duplicate scan index" error.
The reason for this is setting of indio_dev->num_channels based on
accel_3d channel for both gravity and accel-3d sensor. But number of
channels are not same, so for gravity it is pointing to some invalid
memory and getting scan_index to compare which may match.
To fix this issue, set the indio_dev->num_channels correctly based on
the sensor type.
Fixes: 0e377f3b9a ('iio: Add gravity sensor support')
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fix formatting of negative values of type IIO_VAL_FRACTIONAL_LOG2 by
switching from do_div(), which can't handle negative numbers, to
div_s64_rem(). Also use shift_right for shifting, which is safe with
negative values.
Signed-off-by: Nikolaus Schulz <nikolaus.schulz@avionic-design.de>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support for the Analog Devices / Linear Technology
LTC2497 ADCs. The LTC2497 is a 16-channel (eight differential),
16-bit, high precision, delta-sigma ADC with an automatic, differential,
input current cancellation front end and a 2-wire, I2C interface.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fixes the coding style issue of using S_IWUSR in place of 4-digit
octal numbers.
Issue detected by checkpatch.
Signed-off-by: Guru Das Srinagesh <gurooodas@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch initializes the bootime in struct st_sensor_settings for
lps22hb sensor. Without this, sensor channels read from sysfs always
report stale values.
Signed-off-by: Shrirang Bagul <shrirang.bagul@canonical.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The mpu9250 is a SIP containing an mpu6500 and an ak8975. If this was all
there was too it there would be no need for explicit handling in the driver.
Arguably the bindings would also only reflect the presence of an mpu6500 with
the ak8975 hanging off it, as the kernel doesn't care that they are in one
package.
However, the WHOAMI value changes as well so best to add explicit support.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
These bindings are somewhat lagging the state of the driver. The i2c-gate
bindings are documented elsewhere, but it seems sensible to at least have
an example and cross reference in here. SPI bindings will need to be the
subject of a future patch.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
The rk3328 saradc is the same as rk3399.
Signed-off-by: Liang Chen <cl@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The following Coccinelle script was used to detect this:
@r@
expression x;
void* e;
type T;
identifier f;
@@
(
*((T *)e)
|
((T *)x)[...]
|
((T*)x)->f
|
- (T*)
e
)
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The following Coccinelle script was used to detect this:
@r@
expression x;
void* e;
type T;
identifier f;
@@
(
*((T *)e)
|
((T *)x)[...]
|
((T*)x)->f
|
- (T*)
e
)
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The following Coccinelle script was used to detect this:
@r@
expression x;
void* e;
type T;
identifier f;
@@
(
*((T *)e)
|
((T *)x)[...]
|
((T*)x)->f
|
- (T*)
e
)
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The following Coccinelle script was used to detect this:
@r@
expression x;
void* e;
type T;
identifier f;
@@
(
*((T *)e)
|
((T *)x)[...]
|
((T*)x)->f
|
- (T*)
e
)
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The following Coccinelle script was used to detect this:
@r@
expression x;
void* e;
type T;
identifier f;
@@
(
*((T *)e)
|
((T *)x)[...]
|
((T*)x)->f
|
- (T*)
e
)
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The following Coccinelle script was used to detect this:
@r@
expression x;
void* e;
type T;
identifier f;
@@
(
*((T *)e)
|
((T *)x)[...]
|
((T*)x)->f
|
- (T*)
e
)
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Change the name of function from adis16060_spi_write_than_read()
to adis16060_spi_write_then_read(). change "than" to "then" as
its time depended.
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Check for attribute_group structures that are only stored in the
event_attrs filed of iio_info structure. As the event_attrs field of
iio_info structures is constant, so these attribute_group structures can
also be declared constant. Done using coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct attribute_group i@p = {...};
@ok1@
identifier r1.i;
position p;
struct iio_info x;
@@
x.event_attrs=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
static
+const
struct attribute_group i={...};
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct attribute_group i;
As the attrs field of iio_info structures is also constant, so these
attribute_group structures can also be declared constant. Done manually.
File size before:
text data bss dec hex filename
5798 2376 0 8174 1fee drivers/iio/light/lm3533-als.o
File size after:
text data bss dec hex filename
5926 2248 0 8174 1fee drivers/iio/light/lm3533-als.o
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We need to do arithmetics after byte swapping, not before.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
The length field in the Write Zeroes command is a 16-bit field.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
In this case entirely harmless as it's all-ones, but still nice to
shut up sparse.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
The enum values for QPTYPE, PRTYPE and CMS are off by 1 from the
values defined in figure 42 of the NVM Express over Fabrics 1.0:
http://www.nvmexpress.org/wp-content/uploads/NVMe_over_Fabrics_1_0_Gold_20160605-1.pdf
Fix our enums to match the final spec.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
This series enables atomic mode set for vmwgfx. A number of features and
larger fixes are also included.
* 'drm-vmwgfx-next' of git://people.freedesktop.org/~syeh/repos_linux: (22 commits)
drm/vmwgfx: Properly check display/scanout surface size
drm/vmwgfx: Support topology greater than texture size
drm/vmwgfx: Define an overlaid handle_close ioctl.
drm/vmwgfx: Re-implement the stream resource as a simple resource.
drm/vmwgfx: Introduce a simple resource type
drm/vmwgfx: Revert "drm/vmwgfx: Replace numeric parameter like 0444 with macro"
drm/vmwgfx: Fix LDU X blank screen until mode change issue
drm/vmwgfx: Skipping fbdev fb pinning for ldu
drm/vmwgfx: Explicityly track screen target width and height
drm/vmwgfx: Turn on DRIVER_ATOMIC flag
drm/vmwgfx: Switch over to internal atomic API for SOU and LDU
drm/vmwgfx: Switch over to internal atomic API for STDU
drm/vmwgfx: Fixes to vmwgfx_fb
drm/vmwgfx: Add and connect atomic state object check/commit
drm/vmwgfx: Add and connect connector helper function
drm/vmwgfx: Add and connect plane helper functions
drm/vmwgfx: Add and connect CRTC helper functions
drm/vmwgfx: Connector atomic state
drm/vmwgfx: Plane atomic state
drm/vmwgfx: CRTC atomic state
...
David Ahern says:
====================
net: mpls: Allow users to configure more labels per route
Increase the maximum number of new labels for MPLS routes from 2 to 30.
To keep memory consumption in check, the labels array is moved to the end
of mpls_nh and mpls_iptunnel_encap structs as a 0-sized array. Allocations
use the maximum number of labels across all nexthops in a route for LSR
and the number of labels configured for LWT.
The mpls_route layout is changed to:
+----------------------+
| mpls_route |
+----------------------+
| mpls_nh 0 |
+----------------------+
| alignment padding | 4 bytes for odd number of labels; 0 for even
+----------------------+
| via[rt_max_alen] 0 |
+----------------------+
| alignment padding | via's aligned on sizeof(unsigned long)
+----------------------+
| ... |
Meaning the via follows its mpls_nh providing better locality as the
number of labels increases. UDP_RR tests with namespaces shows no impact
to a modest performance increase with this layout for 1 or 2 labels and
1 or 2 nexthops.
mpls_route allocation size is limited to 4096 bytes allowing on the
order of 30 nexthops with 30 labels (or more nexthops with fewer
labels). LWT encap shares same maximum number of labels as mpls routing.
v3
- initialize n_labels to 0 in case RTA_NEWDST is not defined; detected
by the kbuild test robot
v2
- updates per Eric's comments
+ added patch to ensure all reads of rt_nhn_alive and nh_flags in
the packet path use READ_ONCE and all writes via event handlers
use WRITE_ONCE
+ limit mpls_route size to 4096 (PAGE_SIZE for most arch)
+ mostly killed use of MAX_NEW_LABELS; it exists only for common
limit between lwt and routing paths
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alow users to push down more labels per MPLS encap. Similar to LSR case,
move label array to the end of mpls_iptunnel_encap and allocate based on
the number of labels for the route.
For consistency with the LSR case, re-use the same maximum number of
labels.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow users to push down more labels per MPLS route. With the previous
patches, no memory allocations are based on MAX_NEW_LABELS; the limit
is only used to keep userspace in check.
At this point MAX_NEW_LABELS is only used for mpls_route_config (copying
route data from userspace) and processing nexthops looking for the max
number of labels across the route spec.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Limit memory allocation size for mpls_route to 4096.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move labels to the end of mpls_nh as a 0-sized array and within mpls_route
move the via for a nexthop after the mpls_nh. The new layout becomes:
+----------------------+
| mpls_route |
+----------------------+
| mpls_nh 0 |
+----------------------+
| alignment padding | 4 bytes for odd number of labels; 0 for even
+----------------------+
| via[rt_max_alen] 0 |
+----------------------+
| alignment padding | via's aligned on sizeof(unsigned long)
+----------------------+
| ... |
+----------------------+
| mpls_nh n-1 |
+----------------------+
| via[rt_max_alen] n-1 |
+----------------------+
Memory allocated for nexthop + via is constant across all nexthops and
their via. It is based on the maximum number of labels across all nexthops
and the maximum via length. The size is saved in the mpls_route as
rt_nh_size. Accessing a nexthop becomes rt->rt_nh + index * rt->rt_nh_size.
The offset of the via address from a nexthop is saved as rt_via_offset
so that given an mpls_nh pointer the via for that hop is simply
nh + rt->rt_via_offset.
With prior code, memory allocated per mpls_route with 1 nexthop:
via is an ethernet address - 64 bytes
via is an ipv4 address - 64
via is an ipv6 address - 72
With this patch set, memory allocated per mpls_route with 1 nexthop and
1 or 2 labels:
via is an ethernet address - 56 bytes
via is an ipv4 address - 56
via is an ipv6 address - 64
The 8-byte reduction is due to the previous patch; the change introduced
by this patch has no impact on the size of allocations for 1 or 2 labels.
Performance impact of this change was examined using network namespaces
with veth pairs connecting namespaces. ns0 inserts the packet to the
label-switched path using an lwt route with encap mpls. ns1 adds 1 or 2
labels depending on test, ns2 (and ns3 for 2-label test) pops the label
and forwards. ns3 (or ns4) for a 2-label is the destination. Similar
series of namespaces used for 2-nexthop test.
Intent is to measure changes to latency (overhead in manipulating the
packet) in the forwarding path. Tests used netperf with UDP_RR.
IPv4: current patches
1 label, 1 nexthop 29908 30115
2 label, 1 nexthop 29071 29612
1 label, 2 nexthop 29582 29776
2 label, 2 nexthop 29086 29149
IPv6: current patches
1 label, 1 nexthop 24502 24960
2 label, 1 nexthop 24041 24407
1 label, 2 nexthop 23795 23899
2 label, 2 nexthop 23074 22959
In short, the change has no effect to a modest increase in performance.
This is expected since this patch does not really have an impact on routes
with 1 or 2 labels (the current limit) and 1 or 2 nexthops.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Number of nexthops and number of alive nexthops are tracked using an
unsigned int. A route should never have more than 255 nexthops so
convert both to u8. Update all references and intermediate variables
to consistently use u8 as well.
Shrinks the size of mpls_route from 32 bytes to 24 bytes with a 2-byte
hole before the nexthops.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of alive nexthops for a route (rt->rt_nhn_alive) and the
flags for a next hop (nh->nh_flags) are modified by netdev event
handlers. The event handlers run with rtnl_lock held so updates are
always done with the lock held. The packet path accesses the fields
under the rcu lock. Since those fields can change at any moment in
the packet path, both fields should be accessed using READ_ONCE. Updates
to both fields should use WRITE_ONCE.
Update mpls_select_multipath (packet path) and mpls_ifdown and mpls_ifup
(event handlers) accordingly.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault says:
====================
l2tp: fix usage of l2tp_session_find()
l2tp_session_find() doesn't take a reference on the session returned to
its caller. Virtually all l2tp_session_find() users are racy, either
because the session can disappear from under them or because they take
a reference too late. This leads to bugs like 'use after free' or
failure to notice duplicate session creations.
In some cases, taking a reference on the session is not enough. The
special callbacks .ref() and .deref() also have to be called in cases
where the PPP pseudo-wire uses the socket associated with the session.
Therefore, when looking up a session, we also have to pass a flag
indicating if the .ref() callback has to be called.
In the future, we probably could drop the .ref() and .deref() callbacks
entirely by protecting the .sock field of struct pppol2tp_session with
RCU, thus allowing it to be freed and set to NULL even if the L2TP
session is still alive.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Callers of l2tp_nl_session_find() need to hold a reference on the
returned session since there's no guarantee that it isn't going to
disappear from under them.
Relying on the fact that no l2tp netlink message may be processed
concurrently isn't enough: sessions can be deleted by other means
(e.g. by closing the PPPOL2TP socket of a ppp pseudowire).
l2tp_nl_cmd_session_delete() is a bit special: it runs a callback
function that may require a previous call to session->ref(). In
particular, for ppp pseudowires, the callback is l2tp_session_delete(),
which then calls pppol2tp_session_close() and dereferences the PPPOL2TP
socket. The socket might already be gone at the moment
l2tp_session_delete() calls session->ref(), so we need to take a
reference during the session lookup. So we need to pass the do_ref
variable down to l2tp_session_get() and l2tp_session_get_by_ifname().
Since all callers have to be updated, l2tp_session_find_by_ifname() and
l2tp_nl_session_find() are renamed to reflect their new behaviour.
Fixes: 309795f4be ("l2tp: Add netlink control API for L2TP")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
l2tp_session_find() doesn't take any reference on the returned session.
Therefore, the session may disappear while sending the notification.
Use l2tp_session_get() instead and decrement session's refcount once
the notification is sent.
Fixes: 33f72e6f0c ("l2tp : multicast notification to the registered listeners")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
l2tp_session_create() relies on its caller for checking for duplicate
sessions. This is racy since a session can be concurrently inserted
after the caller's verification.
Fix this by letting l2tp_session_create() verify sessions uniqueness
upon insertion. Callers need to be adapted to check for
l2tp_session_create()'s return code instead of calling
l2tp_session_find().
pppol2tp_connect() is a bit special because it has to work on existing
sessions (if they're not connected) or to create a new session if none
is found. When acting on a preexisting session, a reference must be
held or it could go away on us. So we have to use l2tp_session_get()
instead of l2tp_session_find() and drop the reference before exiting.
Fixes: d9e31d17ce ("l2tp: Add L2TP ethernet pseudowire support")
Fixes: fd558d186d ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Holding a reference on session is required before calling
pppol2tp_session_ioctl(). The session could get freed while processing the
ioctl otherwise. Since pppol2tp_session_ioctl() uses the session's socket,
we also need to take a reference on it in l2tp_session_get().
Fixes: fd558d186d ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Taking a reference on sessions in l2tp_recv_common() is racy; this
has to be done by the callers.
To this end, a new function is required (l2tp_session_get()) to
atomically lookup a session and take a reference on it. Callers then
have to manually drop this reference.
Fixes: fd558d186d ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since sctp reconf was added in sctp, the real cnt of in/out stream
have not been c.sinit_max_instreams and c.sinit_num_ostreams any
more.
This patch is to replace them with stream->in/outcnt.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the udp_sock struct, the 'forward_deficit' and 'pcflag' fields
share the same cacheline. While the first is dirtied by
udp_recvmsg, the latter is read, possibly several times, by the
bottom half processing to discriminate between udp and udplite
sockets.
With this patch, sk->sk_protocol is used to check is the socket is
really an udplite one, avoiding some cache misses per
packet and improving the performance under udp_flood with
small packet up to 10%.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull parisc fixes from Helge Deller:
"Al Viro reported that - in case of read faults - our copy_from_user()
implementation may claim to have copied more bytes than it actually
did. In order to fix this bug and because of the way how gcc optimizes
register usage for inline assembly in C code, we had to replace our
pa_memcpy() function with a pure assembler implementation.
While fixing the memcpy bug we noticed some other issues with our
get_user() and put_user() functions, e.g. nested faults may return
wrong data. This is now fixed by a common fixup handler for
get_user/put_user in the exception handler which additionally makes
generated code smaller and faster.
The third patch is a trivial one-line fix for a patch which went in
during 4.11-rc and which avoids stalled CPU warnings after power
shutdown (for parisc machines which can't plug power off themselves).
Due to the rewrite of pa_memcpy() into assembly this patch got bigger
than what I wanted to have sent at this stage.
Those patches have been running in production during the last few days
on our debian build servers without any further issues"
* 'parisc-4.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Avoid stalled CPU warnings after system shutdown
parisc: Clean up fixup routines for get_user()/put_user()
parisc: Fix access fault handling in pa_memcpy()
After commit 96567d5dac ("net: dsa: dsa2: Add basic support of devlink")
I see the following link error with CONFIG_NET_DSA=y and CONFIG_NET_DEVLINK=m:
net/built-in.o: In function 'dsa_register_switch':
(.text+0xe226b): undefined reference to `devlink_alloc'
net/built-in.o: In function 'dsa_register_switch':
(.text+0xe2284): undefined reference to `devlink_register'
net/built-in.o: In function 'dsa_register_switch':
(.text+0xe243e): undefined reference to `devlink_port_register'
net/built-in.o: In function 'dsa_register_switch':
(.text+0xe24e1): undefined reference to `devlink_port_register'
net/built-in.o: In function 'dsa_register_switch':
(.text+0xe24fa): undefined reference to `devlink_port_type_eth_set'
net/built-in.o: In function 'dsa_dst_unapply.part.8':
dsa2.c:(.text.unlikely+0x345): undefined reference to 'devlink_port_unregister'
dsa2.c:(.text.unlikely+0x36c): undefined reference to 'devlink_port_unregister'
dsa2.c:(.text.unlikely+0x38e): undefined reference to 'devlink_port_unregister'
dsa2.c:(.text.unlikely+0x3f2): undefined reference to 'devlink_unregister'
dsa2.c:(.text.unlikely+0x3fb): undefined reference to 'devlink_free'
Fix this by adding a dependency on MAY_USE_DEVLINK so that CONFIG_NET_DSA
get switched to be build as module when CONFIG_NET_DEVLINK=m.
Fixes: 96567d5dac ("net: dsa: dsa2: Add basic support of devlink")
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
