Geminilake platform sports a native HDMI 2.0 controller, and is
capable of driving pixel-clocks upto 594Mhz. HDMI 2.0 spec
mendates scrambling for these higher clocks, for reduced RF footprint.
This patch checks if the monitor supports scrambling, and if required,
enables it during the modeset.
V2: Addressed review comments from Ville:
- Do not track scrambling status in DRM layer, track somewhere in
driver like in intel_crtc_state.
- Don't talk to monitor at such a low layer, set monitor scrambling
in intel_enable_ddi() before enabling the port.
V3: Addressed review comments from Jani
- In comments, function names, use "sink" instead of "monitor",
so that the implementation could be close to the language of
HDMI spec.
V4: Addressed review comment from Maarten
- scrambling -> hdmi_scrambling
- high_tmds_clock_ratio -> hdmi_high_tmds_clock_ratio
V5: Addressed review comments from Ville and Ander
- Do not modifiy the crtc_state after compute_config. Move all
scrambling and tmds_clock_ratio calcutations to compute_config.
- While setting scrambling for source/sink, do not check the
conditions again, just go by the crtc_state flags. This will
simplyfy the condition checks.
V6: Addressed review comments from Ville
- Do not add IS_GLK check in disable/enable function, instead add it
in compute_config, while setting state flags.
- Remove unnecessary paranthesis.
- Simplyfy handle_sink_scrambling function as suggested.
- Add readout code for scrambling status in get_ddi_config and add a
check for the same in pipe_config_compare.
V7: Addressed review comments from Ander/Ville
- No separate function for source scrambling, make it inline
- Align the last line of the macro TRANS_DDI_HDMI_SCRAMBLING_MASK
- Do not add platform check while setting source scrambling
- Use pipe_config instead of crtc->config to set sink scrambling
- To readout scrambling status, Compare with SCRAMBLING_MASK
not any of its bits
- Remove platform check in intel_pipe_config_compare while checking
scrambling status
V8: Fixed mege conflict, Addressed review comments from Ander
- Remove the desciption/comment about scrambling fom the caller, move
it to the function
- Move the IS_GLK check into scrambling function
- Fix alignment
V9: Fixed review comments from Ville, Ander
- Pass the scrambling state variables as bool input to the sink_scrambling
function and let the disable call be unconditional.
- Fix alignments in function calls and debug messages.
- Add kernel doc for function intel_hdmi_handle_sink_scrambling
V10: Rebase
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1489404244-16608-6-git-send-email-shashank.sharma@intel.com
This is just a defensive precaution: do not register notifiers with a
priority which would disrupt the error handling in the notifiers with
prio higher than MCE_PRIO_EDAC.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170327093304.10683-7-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Move all code relating to /dev/mcelog to a separate source file.
/dev/mcelog driver can now operate from the machine check notifier with
lowest prio.
Signed-off-by: Tony Luck <tony.luck@intel.com>
[ Move the mce_helper and trigger functionality behind CONFIG_X86_MCELOG_LEGACY. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170327093304.10683-6-bp@alien8.de
[ Renamed CONFIG_X86_MCELOG to CONFIG_X86_MCELOG_LEGACY. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Introduce a simple data structure for collecting correctable errors
along with accessors. More detailed description in the code itself.
The error decoding is done with the decoding chain now and
mce_first_notifier() gets to see the error first and the CEC decides
whether to log it and then the rest of the chain doesn't hear about it -
basically the main reason for the CE collector - or to continue running
the notifiers.
When the CEC hits the action threshold, it will try to soft-offine the
page containing the ECC and then the whole decoding chain gets to see
the error.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170327093304.10683-5-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
It is confusing when staring at "struct mce_log mcelog" and then there's
also a function called mce_log(). So call the buffer what it is.
No functionality change.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170327093304.10683-4-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We call it everywhere "struct mce *m". Adjust that here too to avoid
confusion.
No functionality change.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170327093304.10683-3-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Since:
cd9c57cad3 ("x86/MCE: Dump MCE to dmesg if no consumers")
all MCEs are printed even when mcelog is running. Fix the regression to
not print to dmesg when mcelog is running as it is a consumer too.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
[ Massage commit message. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: stable@vger.kernel.org # 4.10..
Fixes: cd9c57cad3 ("x86/MCE: Dump MCE to dmesg if no consumers")
Link: http://lkml.kernel.org/r/20170327093304.10683-2-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
0day testing by Fengguang Wu triggered this crash while running Trinity:
kernel BUG at include/linux/pagemap.h:151!
...
CPU: 0 PID: 458 Comm: trinity-c0 Not tainted 4.11.0-rc2-00251-g2947ba0 #1
...
Call Trace:
__get_user_pages_fast()
get_user_pages_fast()
get_futex_key()
futex_requeue()
do_futex()
SyS_futex()
do_syscall_64()
entry_SYSCALL64_slow_path()
It' VM_BUG_ON() due to false-negative in_atomic(). We call
page_cache_get_speculative() with disabled local interrupts.
It should be atomic enough.
So let's check for disabled interrupts in the VM_BUG_ON() condition
too, to resolve this.
( This got triggered by the conversion of the x86 GUP code to the
generic GUP code. )
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: LKP <lkp@01.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20170324114709.pcytvyb3d6ajux33@black.fi.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
New features:
- Handle inline functions in callchains (Jin Yao)
- Enable sorting by srcline as key (Milian Wolff)
Fixes:
- Fix no_size logic in addr_filter__resolve_kernel_syms() in the
auxtrace code (Adrian Hunter)
- Fix some thread refcount leaks in 'perf trace' (Arnaldo Carvalho de Melo)
- Fix divide by zero when calculating percent for an event in a group in
the annotate by source line code (Taeung Song)
- build-id files now aren't anymore symlinks, their parent directories
are, so readlink the later (Taeung Song)
- Assorted fixes for null termination problems, mostly related to
readlink, detected by valgrind (Tommi Rantala)
Infrastructure:
- Make vfs_getname probe point logic in 'perf trace' more robust
wrt length of pathname (Arnaldo Carvalho de Melo)
- Remove unused 'prefix' parameter from builtins main functions (Arnaldo Carvalho de Melo)
- Show 'perf list sdt' option in man page (Ravi Bangoria)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Lm/M
-----END PGP SIGNATURE-----
Merge tag 'perf-core-for-mingo-4.12-20170327' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
New features:
- Handle inline functions in callchains (Jin Yao)
- Enable sorting by srcline as key (Milian Wolff)
Fixes:
- Fix no_size logic in addr_filter__resolve_kernel_syms() in the
auxtrace code (Adrian Hunter)
- Fix some thread refcount leaks in 'perf trace' (Arnaldo Carvalho de Melo)
- Fix divide by zero when calculating percent for an event in a group in
the annotate by source line code (Taeung Song)
- build-id files now aren't anymore symlinks, their parent directories
are, so readlink the later (Taeung Song)
- Assorted fixes for null termination problems, mostly related to
readlink, detected by valgrind (Tommi Rantala)
Infrastructure changes:
- Make vfs_getname probe point logic in 'perf trace' more robust
wrt length of pathname (Arnaldo Carvalho de Melo)
- Remove unused 'prefix' parameter from builtins main functions (Arnaldo Carvalho de Melo)
- Show 'perf list sdt' option in man page (Ravi Bangoria)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
While reviewing the -stable patch for commit 86ef58a4e3 "nfit,
libnvdimm: fix interleave set cookie calculation" Ben noted:
"This is returning an int, thus it's effectively doing a 32-bit
comparison and not the 64-bit comparison you say is needed."
Update the compare operation to be immune to this integer demotion problem.
Cc: <stable@vger.kernel.org>
Cc: Nicholas Moulin <nicholas.w.moulin@linux.intel.com>
Fixes: 86ef58a4e3 ("nfit, libnvdimm: fix interleave set cookie calculation")
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Avoid un-intended DCTI Couples. Use of DCTI couples is deprecated.
Also address the "Programming Note" for optimal performance.
Here is the complete text from Oracle SPARC Architecture Specs.
6.3.4.7 DCTI Couples
"A delayed control transfer instruction (DCTI) in the delay slot of
another DCTI is referred to as a “DCTI couple”. The use of DCTI couples
is deprecated in the Oracle SPARC Architecture; no new software should
place a DCTI in the delay slot of another DCTI, because on future Oracle
SPARC Architecture implementations DCTI couples may execute either
slowly or differently than the programmer assumes it will.
SPARC V8 and SPARC V9 Compatibility Note
The SPARC V8 architecture left behavior undefined for a DCTI couple. The
SPARC V9 architecture defined behavior in that case, but as of
UltraSPARC Architecture 2005, use of DCTI couples was deprecated.
Software should not expect high performance from DCTI couples, and
performance of DCTI couples should be expected to decline further in
future processors.
Programming Note
As noted in TABLE 6-5 on page 115, an annulled branch-always
(branch-always with a = 1) instruction is not architecturally a DCTI.
However, since not all implementations make that distinction, for
optimal performance, a DCTI should not be placed in the instruction word
immediately following an annulled branch-always instruction (BA,A or
BPA,A)."
Signed-off-by: Babu Moger <babu.moger@oracle.com>
Reviewed-by: Rob Gardner <rob.gardner@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I encountered this bug when using /proc/kcore to examine the kernel. Plus a
coworker inquired about debugging tools. We computed pa but did
not use it during the maximum physical address bits test. Instead we used
the identity mapped virtual address which will always fail this test.
I believe the defect came in here:
[bpicco@zareason linus.git]$ git describe --contains bb4e6e85da
v3.18-rc1~87^2~4
.
Signed-off-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series provides a fail-safe mechanism to allow safely re-configuring
mlx5e netdevice and provides a resiliency against sporadic
configuration failures.
To enable this we do some refactoring and code reorganizing to allow
breaking the drivers open/close flows to stages:
open -> activate -> deactivate -> close.
In addition we need to allow creating fresh HW ring resources
(mlx5e_channels) with their own "new" set of parameters, while keeping
the current ones running and active until the new channels are
successfully created with the new configuration, and only then we can
safly replace (switch) old channels with new ones.
For that we introduce mlx5e_channels object and an API to manage it:
- channels = open_channels(new_params):
open fresh TX/RX channels
- activate_channels(channels):
redirect traffic to them and attach them to the netdev
- deactivate_channes(channels)
stop traffic and detach from netdev
- close(channels)
Free the TX/RX HW resources of those channels
With the above strategy it is straightforward to achieve the desired
behavior of fail-safe configuration. In pseudo code:
make_new_config(new_params)
{
old_channels = current_active_channels;
new_channels = create_channels(new_params);
if (!new_channels)
return "Failed, but current channels are still active :)"
deactivate_channels(old_channels); /* Can't fail */
set_hw_new_state(); /* If needed */
activate_channels(new_channels); /* Can't fail */
close_channels(old_channels);
current_active_channels = new_channels;
return "SUCCESS";
}
At the top of this series, we change the following flows to be fail-safe:
ethtool:
- ring parameters
- coalesce parameters
- tx copy break parameters
- cqe compressing/moderation mode setting (priv flags)
ndos:
- tc setup
- set features: LRO
- change mtu
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJY2XfKAAoJEEg/ir3gV/o+6fAIAKBsqf+EYhbHA0JoTnV1sm3G
PSGjj5VCMNTZPyDlTWLEpY2S5TIDRPvICC04i5jWFjo5SOmsRMR6ZV0llHukKC4k
SAkAYU4A78Ds7UhmWzokebwzWa8VA48eqLRxXV60EAhJ0BOgzZnG09KIpzdplE7A
pco+F/c/qzJa0NP1KQBBrYIcXbGMrCFcYM8d6lJ8TRfVDdZZpeTB/wvxRixKfe1L
Ji6+k5tbDynDD3+HWkWq+chAkw4yldN7q8fC8FaN2r0mtWYsYbVSPuP+BlL0XN4R
oluZEJjnyaCePaqUMW+ZYVb1hCGP7pOoJkBb901XdOnX5M2fU9vK3VufWErYF/s=
=r6Qw
-----END PGP SIGNATURE-----
Merge tag 'mlx5e-failsafe' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5e-failsafe 27-03-2017
This series provides a fail-safe mechanism to allow safely re-configuring
mlx5e netdevice and provides a resiliency against sporadic
configuration failures.
To enable this we do some refactoring and code reorganizing to allow
breaking the drivers open/close flows to stages:
open -> activate -> deactivate -> close.
In addition we need to allow creating fresh HW ring resources
(mlx5e_channels) with their own "new" set of parameters, while keeping
the current ones running and active until the new channels are
successfully created with the new configuration, and only then we can
safly replace (switch) old channels with new ones.
For that we introduce mlx5e_channels object and an API to manage it:
- channels = open_channels(new_params):
open fresh TX/RX channels
- activate_channels(channels):
redirect traffic to them and attach them to the netdev
- deactivate_channes(channels)
stop traffic and detach from netdev
- close(channels)
Free the TX/RX HW resources of those channels
With the above strategy it is straightforward to achieve the desired
behavior of fail-safe configuration. In pseudo code:
make_new_config(new_params)
{
old_channels = current_active_channels;
new_channels = create_channels(new_params);
if (!new_channels)
return "Failed, but current channels are still active :)"
deactivate_channels(old_channels); /* Can't fail */
set_hw_new_state(); /* If needed */
activate_channels(new_channels); /* Can't fail */
close_channels(old_channels);
current_active_channels = new_channels;
return "SUCCESS";
}
At the top of this series, we change the following flows to be fail-safe:
ethtool:
- ring parameters
- coalesce parameters
- tx copy break parameters
- cqe compressing/moderation mode setting (priv flags)
ndos:
- tc setup
- set features: LRO
- change mtu
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Mahesh Bandewar says:
====================
link-status fixes for mii-monitoring
The mii monitoring is divided into two phases - inspect and commit. The
inspect phase technically should not make any changes to the state and
defer it to the commit phase. However detected link state inconsistencies
on several machines and discovered that it's the result of some
inconsistent update to link states and assumption that you *always* get
rtnl-mutex. In reality when trylock() fails to acquire rtnl-mutex, the
commit phase is postponed until next mii-mon run. At the next round
because of the state change performed in the previous inspect-run, this
round does not detect any changes and would skip calling commit phase.
This would result in an inconsistent state until next link event happens
(if it ever happens).
During the the commit phase, it's always assumed that speed and duplex
fetch is always successful, but that's always not the case. However the
slave state is marked UP irrespective of speed / duplex fetch operation.
If the speed / duplex fetch operation results in insane values for either
of these two fields, then keeping internal link state UP is not going to
provide fruitful results either.
Please see into individual patches for more details.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
bond_miimon_commit() marks the link UP after attempting to get the speed
and duplex settings for the link. There is a possibility that
bond_update_speed_duplex() could fail. This is another place where it
could result into an inconsistent bonding link state.
With this patch the link will be marked UP only if the speed and duplex
values retrieved have sane values and processed further.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bond_update_speed_duplex() retrieves speed and duplex settings. There
is a possibility of failure in retrieving these values but caller has
to assume it's always successful. This leads to having inconsistent
slave link settings. If these (speed, duplex) values cannot be
retrieved, then keeping the link UP causes problems.
The updated bond_update_speed_duplex() returns 0 on success if it
retrieves sane values for speed and duplex. On failure it returns 1
and marks the link down.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The primary issue is that mii-inspect phase updates link-state and
expects changes to be committed during the mii-commit phase. After
the inspect phase if it fails to acquire rtnl-mutex, the commit
phase (bond_mii_commit) doesn't get to run. This partially updated
state stays and makes the internal-state inconsistent.
e.g. setup bond0 => slaves: eth1, eth2
eth1 goes DOWN -> UP
mii_monitor()
mii-inspect()
bond_set_slave_link_state(eth1, UP, DontNotify)
rtnl_trylock() <- fails!
Next mii-monitor round
eth1: No change
mii_monitor()
mii-inspect()
eth1->link == current-status (ethtool_ops->get_link)
no-change-detected
End result:
eth1:
Link = BOND_LINK_UP
Speed = 0xfffff [SpeedUnknown]
Duplex = 0xff [DuplexUnknown]
This doesn't always happen but for some unlucky machines in a large set
of machines it creates problems.
The fix for this is to avoid making changes during inspect phase and
postpone them until acquiring the rtnl-mutex / invoking commit phase.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split the function into two (a) propose (b) commit phase without
changing the semantics for the original API.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our chosen ic_dev may be anywhere in our list of ic_devs, and we may
free it before attempting to close others. When we compare d->dev and
ic_dev->dev, we're potentially dereferencing memory returned to the
allocator. This causes KASAN to scream for each subsequent ic_dev we
check.
As there's a 1-1 mapping between ic_devs and netdevs, we can instead
compare d and ic_dev directly, which implicitly handles the !ic_dev
case, and avoids the use-after-free. The ic_dev pointer may be stale,
but we will not dereference it.
Original splat:
[ 6.487446] ==================================================================
[ 6.494693] BUG: KASAN: use-after-free in ic_close_devs+0xc4/0x154 at addr ffff800367efa708
[ 6.503013] Read of size 8 by task swapper/0/1
[ 6.507452] CPU: 5 PID: 1 Comm: swapper/0 Not tainted 4.11.0-rc3-00002-gda42158 #8
[ 6.514993] Hardware name: AppliedMicro Mustang/Mustang, BIOS 3.05.05-beta_rc Jan 27 2016
[ 6.523138] Call trace:
[ 6.525590] [<ffff200008094778>] dump_backtrace+0x0/0x570
[ 6.530976] [<ffff200008094d08>] show_stack+0x20/0x30
[ 6.536017] [<ffff200008bee928>] dump_stack+0x120/0x188
[ 6.541231] [<ffff20000856d5e4>] kasan_object_err+0x24/0xa0
[ 6.546790] [<ffff20000856d924>] kasan_report_error+0x244/0x738
[ 6.552695] [<ffff20000856dfec>] __asan_report_load8_noabort+0x54/0x80
[ 6.559204] [<ffff20000aae86ac>] ic_close_devs+0xc4/0x154
[ 6.564590] [<ffff20000aaedbac>] ip_auto_config+0x2ed4/0x2f1c
[ 6.570321] [<ffff200008084b04>] do_one_initcall+0xcc/0x370
[ 6.575882] [<ffff20000aa31de8>] kernel_init_freeable+0x5f8/0x6c4
[ 6.581959] [<ffff20000a16df00>] kernel_init+0x18/0x190
[ 6.587171] [<ffff200008084710>] ret_from_fork+0x10/0x40
[ 6.592468] Object at ffff800367efa700, in cache kmalloc-128 size: 128
[ 6.598969] Allocated:
[ 6.601324] PID = 1
[ 6.603427] save_stack_trace_tsk+0x0/0x418
[ 6.607603] save_stack_trace+0x20/0x30
[ 6.611430] kasan_kmalloc+0xd8/0x188
[ 6.615087] ip_auto_config+0x8c4/0x2f1c
[ 6.619002] do_one_initcall+0xcc/0x370
[ 6.622832] kernel_init_freeable+0x5f8/0x6c4
[ 6.627178] kernel_init+0x18/0x190
[ 6.630660] ret_from_fork+0x10/0x40
[ 6.634223] Freed:
[ 6.636233] PID = 1
[ 6.638334] save_stack_trace_tsk+0x0/0x418
[ 6.642510] save_stack_trace+0x20/0x30
[ 6.646337] kasan_slab_free+0x88/0x178
[ 6.650167] kfree+0xb8/0x478
[ 6.653131] ic_close_devs+0x130/0x154
[ 6.656875] ip_auto_config+0x2ed4/0x2f1c
[ 6.660875] do_one_initcall+0xcc/0x370
[ 6.664705] kernel_init_freeable+0x5f8/0x6c4
[ 6.669051] kernel_init+0x18/0x190
[ 6.672534] ret_from_fork+0x10/0x40
[ 6.676098] Memory state around the buggy address:
[ 6.680880] ffff800367efa600: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 6.688078] ffff800367efa680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 6.695276] >ffff800367efa700: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 6.702469] ^
[ 6.705952] ffff800367efa780: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 6.713149] ffff800367efa800: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 6.720343] ==================================================================
[ 6.727536] Disabling lock debugging due to kernel taint
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: David S. Miller <davem@davemloft.net>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: James Morris <jmorris@namei.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
For the current task, the kernel stack would only tell the last time the
process was rescheduled, if ever. Use the current stack pointer for the
current task.
Otherwise, every once in a while, the stacktrace printed when reading
/proc/self/stack would look like the process is running in userspace,
while it's not, which some may consider as a bug.
This is also consistent with some other architectures, like x86 and arm,
at least.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Seems like coefficient values for m, b and R under power have been
put in the wrong order. Rearranging them properly to get correct
values of coefficients for power.
For specs, please refer to table 7 (page 35) on
http://www.analog.com/media/en/technical-documentation/data-sheets/ADM1075.pdf
Fixes: 904b296f30 ("hwmon: (adm1275) Introduce configuration data structure for coeffcients")
Signed-off-by: Shikhar Dogra <shidogra@cisco.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The email address is undeliverable for some time now, so just remove it.
Signed-off-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Version 11.4.0.0
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update Broadcom Copyright markings in all files.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Data in buffers are gathered into a single buffer before giving to iSCSI
layer. Though less likely to have payload more than 8K in ASYNC PDU, the
data length is provide by FW and check is missing for overrun.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With previous patch adding ASYNC Rx buffers to free_list is not
required. Remove all free_list related operations.
Add in_use to track if buffer posted is being processed by driver and
purge all buffers received for connection if found so.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
FW runs out of buffer if buffers are not posted back soon. ASYNC Rx CQE
indicates that FW has consumed 8 RQEs. Use it to post back buffers
instead of waiting for buffers to be processed and freed by driver.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, ASYNC PDU default queue size is set to max connections. This
leaves only one buffer per connection for any ASYNC PDUs from targets.
Double the size of the default queue.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi_flush_work flushes workqueue for the Scsi_Host. In iSCSI offload
enabled host, this would wait for all other sessions under the host.
Use flush_work for the session being removed instead.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
spin_unlock_bh back_lock is used in beiscsi_eh_device_reset instead of
spin_lock.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
CID needs to be freed even when invalidate or upload connection fails.
Attempt to close connection 3 times before freeing CID.
Set cleanup_type to INVALIDATE instead of force TCP_RST. This
unnecessarily is terminating connection with reset instead of gracefully
closing it.
Set save_cfg to 0 - session not to be saved on flash.
Add delay and process CQ before uploading connection.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
These aren't really falling through to anywhere meaningful.
Signed-off-by: Tomohiro Kusumi <tkusumi@tuxera.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We don't call the remove() function unless probe() succeeds so "oud"
can't be NULL here. Plus, if it were NULL, we dereference it on the
next line so it would crash anyway.
[mkp: applied by hand]
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Boaz Harrosh <ooo@electrozaur.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are same conditions for checking whether supporting clkscaling or
not. When ufshcd is supporting clkscaling, active_reqs should be
decreased by one.
[mkp: addressed comment from Bartlomiej]
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-03-27
This series contains updates to i40e and i40evf only.
Alex updates the driver code so that we can do bulk updates of the page
reference count instead of just incrementing it by one reference at a
time. Fixed an issue where we were not resetting skb back to NULL when
we have freed it. Cleaned up the i40e_process_skb_fields() to align with
other Intel drivers. Removed FCoE code, since it is not supported in any
of the Fortville/Fortpark hardware, so there is not much point of carrying
the code around, especially if it is broken and untested.
Harshitha fixes a bug in the driver where the calculation of the RSS size
was not taking into account the number of traffic classes enabled.
Robert fixes a potential race condition during VF reset by eliminating
IOMMU DMAR Faults caused by VF hardware and when the OS initiates a VF
reset and before the reset is finished we modify the VF's settings.
Bimmy removes a delay that is no longer needed, since it was only needed
for preproduction hardware.
Colin King fixes null pointer dereference, where VSI was being
dereferenced before the VSI NULL check.
Jake fixes an issue with the recent addition of the "client code" to the
driver, where we attempt to use an uninitialized variable, so correctly
initialize the params variable by calling i40e_client_get_params().
v2: dropped patch 5 of the original series from Carolyn since we need
more documentation and reason why the added delay, so Carolyn is
taking the time to update the patch before we re-submit it for
kernel inclusion.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We switched from "struct task_struct"->security to "struct cred"->security
in Linux 2.6.29. But not all LSM modules were happy with that change.
TOMOYO LSM module is an example which want to use per "struct task_struct"
security blob, for TOMOYO's security context is defined based on "struct
task_struct" rather than "struct cred". AppArmor LSM module is another
example which want to use it, for AppArmor is currently abusing the cred
a little bit to store the change_hat and setexeccon info. Although
security_task_free() hook was revived in Linux 3.4 because Yama LSM module
wanted to release per "struct task_struct" security blob,
security_task_alloc() hook and "struct task_struct"->security field were
not revived. Nowadays, we are getting proposals of lightweight LSM modules
which want to use per "struct task_struct" security blob.
We are already allowing multiple concurrent LSM modules (up to one fully
armored module which uses "struct cred"->security field or exclusive hooks
like security_xfrm_state_pol_flow_match(), plus unlimited number of
lightweight modules which do not use "struct cred"->security nor exclusive
hooks) as long as they are built into the kernel. But this patch does not
implement variable length "struct task_struct"->security field which will
become needed when multiple LSM modules want to use "struct task_struct"->
security field. Although it won't be difficult to implement variable length
"struct task_struct"->security field, let's think about it after we merged
this patch.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: John Johansen <john.johansen@canonical.com>
Acked-by: Serge Hallyn <serge@hallyn.com>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
Tested-by: Djalal Harouni <tixxdz@gmail.com>
Acked-by: José Bollo <jobol@nonadev.net>
Cc: Paul Moore <paul@paul-moore.com>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: Eric Paris <eparis@parisplace.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: James Morris <james.l.morris@oracle.com>
Cc: José Bollo <jobol@nonadev.net>
Signed-off-by: James Morris <james.l.morris@oracle.com>
cpu_ready_for_interrupts() is called after feature patching, so there's
no need to use early_cpu_has_feature().
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The config option for the POWER8 crc32c recently changed from
CONFIG_CRYPT_CRC32C_VPMSUM to CONFIG_CRYPTO_CRC32C_VPMSUM. Update
the configs.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Most people use perf these days, so save about 31kB by making oprofile
a module.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It turns out cloud-config uses ISO9660 filesystems to inject
configuration data into cloud images. The cloud-config failures when
ISO9660_FS is not enabled are cryptic, and building it in makes
mainline testing easier, so re-enable it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER9 adds form 1 scoms. The form of the indirection is specified in
the top nibble of the scom address.
Currently we do some (ugly) bit mangling so that we can fit a 64 bit
scom address into the debugfs interface. The current code only shifts
the top bit (indirect bit).
This patch changes it to shift the whole top nibble so that the form
of the indirection is also shifted.
This patch is backwards compatible with older scoms.
(This change isn't required in the arch/powerpc/platforms/powernv/opal-prd.c
scom interface as it passes the whole 64bit scom address without any bit
mangling)
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently the code to perform an OPAL call is duplicated between the
normal path and path taken when tracepoints are enabled. There's no
real need for this and combining them makes opal_tracepoint_entry
considerably easier to understand.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
