Some platform based configuration setup of spi-imx SPI devices does
not set the "chip_select" to the actual hardware chip select used.
This works because the cs_gpio mapping that is associated with this
platform setup maps the chip_select offset used to the appropriate
hardware chip select. The spi-imx driver uses the chip_select as an
index into the cs_gpio array and ultimately gets the correct hardware
chip select for its hardware setup.
The motivation is to be able to eventually modify the spi-imx code to
use the "chip_select" directly for harwdare setup instead of indirectly
via the cs_gpio mapping array.
This change only affects platforms using the hardware chip select
addressing method for their SPI devices (sometimes called native chip
select). The majority of devices using the spi-imx driver use the GPIO
addressing method.
The change to use the correct "chip_select" is strait forward. But the
cs_gpio mapping arrary also needs to be modifed to match that change. In
simple terms the cs_gpio mapping should always have the hardware chip
select number at its same index offset.
There is no functional change with these patches. The three affected
platforms should work exactly as before. However I don't have any of
these platforms (or access to them) and so I can't test them. So this
patch is compile tested only.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The kvmgt code keeps a pointer to the struct kvm associated with the
device, but doesn't actually hold a reference to it. If we do unclean
shutdown testing (ie. killing the user process), then we can see the
kvm association to the device unset, which causes kvmgt to trigger a
device release via a work queue. Naturally we cannot guarantee that
the cached struct kvm pointer is still valid at this point without
holding a reference. The observed failure in this case is a stuck
cpu trying to acquire the spinlock from the invalid reference, but
other failure modes are clearly possible. Hold a reference to avoid
this.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: stable@vger.kernel.org #v4.10
Cc: Jike Song <jike.song@intel.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Zhi Wang <zhi.a.wang@intel.com>
Reviewed-by: Jike Song <jike.song@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
- Initial support for the Prefetch Resolve Engine/Gasket on i.MX6QP,
improving linear scanout buffer memory bandwidth utilization. This
will in the future grow reordering support and allow direct scanout
of Vivante tiled renderbuffers from the GPU.
- Deferred plane disabling gets rid of some busy waiting in the atomic
plane disable and crtc disable paths that lead to wait_for_vblank
timeouts.
- Add support for RGBA formats with a separate alpha plane, that can
reduce memory bandwidth utilization for mostly transparent overlay
planes by skipping color reads for completely transparent regions.
- Allow moving an active overlay plane without enforcing a modeset.
- Add 8-bit and 16-bit bayer formats to ipu_cpmem_set_image.
- Set the base address in ipu_cpmem_set_image even for invalid formats
to increase robustness against errors.
- Use drm_plane_helper_check_state in plane atomic_check.
- Some cleanup.
-----BEGIN PGP SIGNATURE-----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=dyZf
-----END PGP SIGNATURE-----
Merge tag 'imx-drm-next-2017-03-17' of git://git.pengutronix.de/git/pza/linux into drm-next
imx-drm PRE/PRG support, deferred plane disabling, separate alpha support
- Initial support for the Prefetch Resolve Engine/Gasket on i.MX6QP,
improving linear scanout buffer memory bandwidth utilization. This
will in the future grow reordering support and allow direct scanout
of Vivante tiled renderbuffers from the GPU.
- Deferred plane disabling gets rid of some busy waiting in the atomic
plane disable and crtc disable paths that lead to wait_for_vblank
timeouts.
- Add support for RGBA formats with a separate alpha plane, that can
reduce memory bandwidth utilization for mostly transparent overlay
planes by skipping color reads for completely transparent regions.
- Allow moving an active overlay plane without enforcing a modeset.
- Add 8-bit and 16-bit bayer formats to ipu_cpmem_set_image.
- Set the base address in ipu_cpmem_set_image even for invalid formats
to increase robustness against errors.
- Use drm_plane_helper_check_state in plane atomic_check.
- Some cleanup.
* tag 'imx-drm-next-2017-03-17' of git://git.pengutronix.de/git/pza/linux: (22 commits)
drm/imx: Remove unneeded definition for structure imx_drm_component
drm/imx: use PRG/PRE when possible
drm/imx: enable/disable PRG on CRTC enable/disable
gpu: ipu-v3: only set non-zero AXI ID for IC when PRG is absent
gpu: ipu-v3: hook up PRG unit
gpu: ipu-v3: document valid IPUv3 compatibles and extend for i.MX6 QuadPlus
gpu: ipu-v3: add driver for Prefetch Resolve Gasket
gpu: ipu-v3: add DT binding for the Prefetch Resolve Gasket
gpu: ipu-v3: add driver for Prefetch Resolve Engine
gpu: ipu-v3: add DT binding for the Prefetch Resolve Engine
drm/imx: ipuv3-plane: add support for separate alpha planes
drm/imx: extend drm_plane_state_to_eba for separate channel support
gpu: ipu-v3: add support for separate alpha channels
drm: add RGB formats with separate alpha plane
drm/imx: add deferred plane disabling
drm/imx: don't wait for vblank and stop calling cleanup_planes in commit_tail
gpu: ipu-v3: add unsynchronised DP channel disabling
gpu: ipu-v3: remove IRQ dance on DC channel disable
gpu: ipu-cpmem: add bayer formats to ipu_cpmem_set_image
gpu: ipu-cpmem: set image base address even for incorrect formats
...
This BUG_ON() triggered for me once at shutdown, and I don't see a
reason for the check. The code correctly checks whether the swap slot
cache is usable or not, so an uninitialized swap slot cache is not
actually problematic afaik.
I've temporarily just switched the BUG_ON() to a WARN_ON_ONCE(), since
I'm not sure why that seemingly pointless check was there. I suspect
the real fix is to just remove it entirely, but for now we'll warn about
it but not bring the machine down.
Cc: "Huang, Ying" <ying.huang@intel.com>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Wire up statx() syscall
- Don't print a warning on memory hotplug when HPT resizing isn't available
Thanks to:
David Gibson, Chandan Rajendra.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=TfiW
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.11-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull more powerpc fixes from Michael Ellerman:
"A couple of minor powerpc fixes for 4.11:
- wire up statx() syscall
- don't print a warning on memory hotplug when HPT resizing isn't
available
Thanks to: David Gibson, Chandan Rajendra"
* tag 'powerpc-4.11-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/pseries: Don't give a warning when HPT resizing isn't available
powerpc: Wire up statx() syscall
Pull parisc fixes from Helge Deller:
- Mikulas Patocka added support for R_PARISC_SECREL32 relocations in
modules with CONFIG_MODVERSIONS.
- Dave Anglin optimized the cache flushing for vmap ranges.
- Arvind Yadav provided a fix for a potential NULL pointer dereference
in the parisc perf code (and some code cleanups).
- I wired up the new statx system call, fixed some compiler warnings
with the access_ok() macro and fixed shutdown code to really halt a
system at shutdown instead of crashing & rebooting.
* 'parisc-4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix system shutdown halt
parisc: perf: Fix potential NULL pointer dereference
parisc: Avoid compiler warnings with access_ok()
parisc: Wire up statx system call
parisc: Optimize flush_kernel_vmap_range and invalidate_kernel_vmap_range
parisc: support R_PARISC_SECREL32 relocation in modules
Pull SCSI target fixes from Nicholas Bellinger:
"The bulk of the changes are in qla2xxx target driver code to address
various issues found during Cavium/QLogic's internal testing (stable
CC's included), along with a few other stability and smaller
miscellaneous improvements.
There are also a couple of different patch sets from Mike Christie,
which have been a result of his work to use target-core ALUA logic
together with tcm-user backend driver.
Finally, a patch to address some long standing issues with
pass-through SCSI export of TYPE_TAPE + TYPE_MEDIUM_CHANGER devices,
which will make folks using physical (or virtual) magnetic tape happy"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (28 commits)
qla2xxx: Update driver version to 9.00.00.00-k
qla2xxx: Fix delayed response to command for loop mode/direct connect.
qla2xxx: Change scsi host lookup method.
qla2xxx: Add DebugFS node to display Port Database
qla2xxx: Use IOCB interface to submit non-critical MBX.
qla2xxx: Add async new target notification
qla2xxx: Export DIF stats via debugfs
qla2xxx: Improve T10-DIF/PI handling in driver.
qla2xxx: Allow relogin to proceed if remote login did not finish
qla2xxx: Fix sess_lock & hardware_lock lock order problem.
qla2xxx: Fix inadequate lock protection for ABTS.
qla2xxx: Fix request queue corruption.
qla2xxx: Fix memory leak for abts processing
qla2xxx: Allow vref count to timeout on vport delete.
tcmu: Convert cmd_time_out into backend device attribute
tcmu: make cmd timeout configurable
tcmu: add helper to check if dev was configured
target: fix race during implicit transition work flushes
target: allow userspace to set state to transitioning
target: fix ALUA transition timeout handling
...
Pull device-dax fixes from Dan Williams:
"The device-dax driver was not being careful to handle falling back to
smaller fault-granularity sizes.
The driver already fails fault attempts that are smaller than the
device's alignment, but it also needs to handle the cases where a
larger page mapping could be established. For simplicity of the
immediate fix the implementation just signals VM_FAULT_FALLBACK until
fault-size == device-alignment.
One fix is for -stable to address pmd-to-pte fallback from the
original implementation, another fix is for the new (introduced in
4.11-rc1) pud-to-pmd regression, and a typo fix comes along for the
ride.
These have received a build success notification from the kbuild
robot"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
device-dax: fix debug output typo
device-dax: fix pud fault fallback handling
device-dax: fix pmd/pte fault fallback handling
Callers must provide a valid port group to alua_rtpg_queue(). Issue a
kernel warning if that is not the case.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Tang Junhui <tang.junhui@zte.com.cn>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Callers of scsi_dh_activate(), e.g. dm-mpath, assume that this function
either returns an error code or calls the completion function. Make
alua_activate() call the completion function even if scsi_device_get()
fails.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Tang Junhui <tang.junhui@zte.com.cn>
Cc: <stable@vger.kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For mysterious historical reasons, struct user_desc doesn't indicate
whether segments are accessed. set_thread_area() has always programmed
segments as non-accessed, so the first write will set the accessed bit.
This will fault if the GDT is read-only.
Fix it by making TLS segments start out accessed.
If this ends up breaking something, we could, in principle, leave TLS
segments non-accessed and fix them up when we get the page fault. I'd be
surprised, though -- AFAIK all the nasty legacy segmented programs (DOSEMU,
Wine, things that run on DOSEMU and Wine, etc.) do their nasty segmented
things using the LDT and not the GDT. I assume this is mainly because old
OSes (Linux and otherwise) didn't historically provide APIs to do nasty
things in the GDT.
Fixes: 45fc8757d1 ("x86: Make the GDT remapping read-only on 64-bit")
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Thomas Garnier <thgarnie@google.com>
Link: http://lkml.kernel.org/r/62b7748542df0164af7e0a5231283b9b13858c45.1489900519.git.luto@kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The IIO subsystem is redefining iio_dev->mlock to be used by
the IIO core only for protecting device operating mode changes.
ie. Changes between INDIO_DIRECT_MODE, INDIO_BUFFER_* modes.
In this driver, mlock was being used to protect hardware state
changes. Replace it with a lock in the devices global data.
Signed-off-by: Gargi Sharma <gs051095@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fix checkpatch warning:
Statements should start on a tabstop.
Signed-off-by: Miguel Robles <miguel.robles@farole.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fix checkpatch warnings:
Symbolic permissions 'S_IWUSR' are not preferred.
Signed-off-by: Miguel Robles <miguel.robles@farole.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The function adis16209_read_raw() is safe to be run in parallel.
The call to adis_read_reg_16() is safe since adis_read_reg() uses the
txrx_lock from struct adis to protect simultaneous changes.
Remove mutex.h inclusion since it is no longer needed.
Signed-off-by: Narcisa Ana Maria Vasile <narcisaanamaria12@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver has a OF device ID table but the struct i2c_driver
.of_match_table field is not set.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Crt Mori <cmo@melexis.com>
Acked-by: Crt Mori <cmo@melexis.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fixes: 290a6ce11d (iio: imu: add support to lsm6dsx driver)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fix checkpatch warnings:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
Signed-off-by: Miguel Robles <miguel.robles@farole.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In the driver adis16201 read raw does not require an iio_dev->mlock for
reads. It can run concurrently as adis_read_reg_16() is protected by a
transaction lock.
Signed-off-by: Aishwarya Pant <aishpant@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Current driver wait for FW to be in the ready state before
processing in-coming commands. For Arbitrated Loop or
Point-to- Point (not switch), FW Ready state can take a while.
FW will transition to ready state after all Nports have been
logged in. In the mean time, certain initiators have completed
the login and starts IO. Driver needs to start processing all
queues if FW is already started.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
For target mode, when new scsi command arrive, driver first performs
a look up of the SCSI Host. The current look up method is based on
the ALPA portion of the NPort ID. For Cisco switch, the ALPA can
not be used as the index. Instead, the new search method is based
on the full value of the Nport_ID via btree lib.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The Mailbox interface is currently over subscribed. We like
to reserve the Mailbox interface for the chip managment and
link initialization. Any non essential Mailbox command will
be routed through the IOCB interface. The IOCB interface is
able to absorb more commands.
Following commands are being routed through IOCB interface
- Get ID List (007Ch)
- Get Port DB (0064h)
- Get Link Priv Stats (006Dh)
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If the remote port have started the login process, then the
PLOGI and PRLI should be back to back. Driver will allow
the remote port to complete the process. For the case where
the remote port decide to back off from sending PRLI, this
local port sets an expiration timer for the PRLI. Once the
expiration time passes, the relogin retry logic is allowed
to go through and perform login with the remote port.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The main lock that needs to be held for CMD or TMR submission
to upper layer is the sess_lock. The sess_lock is used to
serialize cmd submission and session deletion. The addition
of hardware_lock being held is not necessary. This patch removes
hardware_lock dependency from CMD/TMR submission.
Use hardware_lock only for error response in this case.
Path1
CPU0 CPU1
---- ----
lock(&(&ha->tgt.sess_lock)->rlock);
lock(&(&ha->hardware_lock)->rlock);
lock(&(&ha->tgt.sess_lock)->rlock);
lock(&(&ha->hardware_lock)->rlock);
Path2/deadlock
*** DEADLOCK ***
Call Trace:
dump_stack+0x85/0xc2
print_circular_bug+0x1e3/0x250
__lock_acquire+0x1425/0x1620
lock_acquire+0xbf/0x210
_raw_spin_lock_irqsave+0x53/0x70
qlt_sess_work_fn+0x21d/0x480 [qla2xxx]
process_one_work+0x1f4/0x6e0
Cc: <stable@vger.kernel.org>
Cc: Bart Van Assche <Bart.VanAssche@sandisk.com>
Reported-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Normally, ABTS is sent to Target Core as Task MGMT command.
In the case of error, qla2xxx needs to send response, hardware_lock
is required to prevent request queue corruption.
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
