Make nvkm_secboot_falcon_name publicly visible as other subdevs will
need to use it for debug messages.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ideally we'd be able to keep these at a more obvious error level, as
they're a good indication of us doing something wrong.
However, NVIDIA's FECS/GPCCS firmware touches registers that trigger
priv ring faults, and we can't do anything to fix that ourselves due
to the need for them to be signed by NVIDIA.
This issue was reported a while back, but hasn't been fixed, so, for
now we will hide the messages to prevent spamming Optimus users with
messages whenever the NVIDIA GPU is powered off and on again.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Current Audio-DMAC is assigned "rx" as Audio-DMAC0, "tx" as Audio-DMAC1.
Thus, DVC "tx" should be assigned as Audio-DMAC1, instead of Audio-DMAC0.
Because of this, current platform board (using SRC/DVC/SSI)
Playback/Capture both will use same Audio-DMAC0
(but it depends on audio data path).
First note is that this "rx" and "tx" are from each IP point,
it doesn't mean Playback/Capture.
Second note is that Audio DMAC assigned on DT is only for
Audio-DMAC, Audio-DMAC-peri-peri has no entry.
=> Audio-DMAC
-> Audio-DMAC-peri-peri
-- HW connection
Playback case
[Mem] => [SRC]--[DVC] -> [SSI]--[Codec]
rx ~~~~~~~~~~~~
Capture
[Mem] <= [DVC]--[SRC] <- [SSI]--[Codec]
tx ~~~~~~~~~~~~
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The EthernetAVB should not depend on the bootloader to setup correct
drive-strength values. Values for drive-strength where found by
examining the registers after the bootloader has configured the
registers and successfully used the EthernetAVB.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Cortex-A57 cache controller is an integrated controller, and thus
the device node representing it should not have a unit-addresses or reg
property.
Fixes: 1561f20760 ("arm64: dts: r8a7796: Add Renesas R8A7796 SoC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Cortex-A57/A53 cache controllers are integrated controllers, and
thus the device nodes representing them should not have unit-addresses
or reg properties.
Fixes: 6f7bf82cc9 ("arm64: dts: r8a7795: Fix W=1 dtc warnings")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
>From PSCI v1.0, Suspend-to-RAM is supported via SYSTEM_SUSPEND PSCI
function call. Hence, upgrade PSCI version for R-Car M3-W to support
Suspend-to-RAM.
The Suspend-to-RAM is highly dependent on ARM Trusted Firwmare support
since necessary callback functions will be registered after a query
to ARM Trusted Firmware about SYSTEM_SUSPEND support.
Since PSCI v1.0 is backward compatible with PSCI v0.2, CPU Hotplug and
CPUIdle should be able to work normally with this change.
Signed-off-by: Khiem Nguyen <khiem.nguyen.xt@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Keep "arm,psci-0.2"]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
>From PSCI v1.0, Suspend-to-RAM is supported via SYSTEM_SUSPEND PSCI
function call. Hence, upgrade PSCI version for R-Car H3 to support
Suspend-to-RAM.
The Suspend-to-RAM is highly dependent on ARM Trusted Firwmare support
since necessary callback functions will be registered after a query
to ARM Trusted Firmware about SYSTEM_SUSPEND support.
Since PSCI v1.0 is backward compatible with PSCI v0.2, CPU Hotplug and
CPUIdle should be able to work normally with this change.
Signed-off-by: Khiem Nguyen <khiem.nguyen.xt@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Keep "arm,psci-0.2"]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the performance monitor unit for the Cortex-A53 cores on the
R8A7795 SoC.
Extracted from a patch by Takeshi Kihara in the BSP.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds Cortex-A53 CPU cores to r8a7795 SoC for a total of 8
cores (4 x Cortex-A57 + 4 x Cortex-A53).
Based on work by Takeshi Kihara and Dirk Behme.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enables the SCIF hooked up to the DEBUG1 connector.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device nodes for all R-Car H3 SCIF serial ports, incl. clocks
and power domain.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device nodes for all HSCIF serial ports, incl. clocks, and
power domain.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
[simon: express register size in hex; refer to power domain in changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Current Audio-DMAC is assigned "rx" as Audio-DMAC0, "tx" as Audio-DMAC1.
Thus, DVC "tx" should be assigned as Audio-DMAC1, instead of Audio-DMAC0.
Because of this, current platform board (using SRC/DVC/SSI)
Playback/Capture both will use same Audio-DMAC0
(but it depends on data path).
First note is that this "rx" and "tx" are from each IP point,
it doesn't mean Playback/Capture.
Second note is that Audio DMAC assigned on DT is only for
Audio-DMAC, Audio-DMAC-peri-peri has no entry.
=> Audio-DMAC
-> Audio-DMAC-peri-peri
-- HW connection
Playback case
[Mem] => [SRC]--[DVC] -> [SSI]--[Codec]
rx ~~~~~~~~~~~~
Capture
[Mem] <= [DVC]--[SRC] <- [SSI]--[Codec]
tx ~~~~~~~~~~~~
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Cortex-A7 cache controller is an integrated controller, and thus the
device node representing it should not have a unit-addresses or reg
property.
Fixes: 34ea4b4a82 ("ARM: dts: r8a7794: Fix W=1 dtc warnings")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Cortex-A15 cache controller is an integrated controller, and thus
the device node representing it should not have a unit-addresses or reg
property.
Fixes: ad53f5f00b ("ARM: dts: r8a7793: Fix W=1 dtc warnings")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Cortex-A15 cache controller is an integrated controller, and thus
the device node representing it should not have a unit-addresses or reg
property.
Fixes: 7c4163aae3 ("ARM: dts: r8a7792: initial SoC device tree")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Cortex-A15 cache controller is an integrated controller, and thus
the device node representing it should not have a unit-addresses or reg
property.
Fixes: 6f9314ce25 ("ARM: dts: r8a7791: Fix W=1 dtc warnings")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Cortex-A15/A7 cache controllers are integrated controllers, and thus
the device nodes representing them should not have unit-addresses or reg
properties.
Fixes: 2c3de36700 ("ARM: dts: r8a7790: Fix W=1 dtc warnings")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Cortex-A7 cache controller is an integrated controller, and thus the
device node representing it should not have a unit-addresses or reg
property.
Fixes: c95360247b ("ARM: dts: r8a7745: initial SoC device tree")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Cortex-A15 cache controller is an integrated controller, and thus
the device node representing it should not have a unit-addresses or reg
property.
Fixes: 34e8d993a6 ("ARM: dts: r8a7743: initial SoC device tree")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Cortex-A15/A7 cache controllers are integrated controllers, and thus
the device nodes representing them should not have unit-addresses or reg
properties.
Fixes: b0da45c60d ("ARM: dts: r8a73a4: Fix W=1 dtc warnings")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch replace "is is " with "is". The replacement couldn't be
automated because sometimes the first "is" was meant to be another
word.
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
udelay is impelmented using a busy-wait loop and consumes CPU cycles
while usleep_range is implemented using interrupts.cls_flush_uart_write()
is called after a channel lock is acquired i.e. an atomic context.
Hence delay in this method should use udelay instead of usleep_range.
Signed-off-by: Aishwarya Pant <aishpant@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ktermios structure is a local default termios struct. All ports
are initially created with this termios. Since, the structure is
never modified, it can be declared as const.
Coccinelle Script:
@r disable optional_qualifier@
identifier s,i;
position p;
@@
static struct ktermios i@p = { ... };
@ok1@
identifier r.i;
expression e;
position p;
@@
e = i@p
@bad@
position p != {r.p,ok1.p};
identifier r.i;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct ktermios i = { ... };
File Size before:
text data bss dec hex filename
25469 2048 256 27773 6c7d drivers/staging/dgnc/dgnc_tty.o
File Size after:
text data bss dec hex filename
25636 2016 256 27908 6d04 drivers/staging/dgnc/dgnc_tty.o
Signed-off-by: Gargi Sharma <gs051095@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Call qxl_add_monitors_config_modes() unconditionally. Do all sanity
checks in that function.
Fix sanity checks. monitors_config is the current monitor
configuration, whereas client_monitors_config is the configuration
requested by the spice client. So when filling the mode list, based on
the spice client request, we need to look at
client_monitors_config->count not monitors_config->count.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1488363154-6889-5-git-send-email-kraxel@redhat.com
Try to read the client monitors config at driver load time, even without
explicit notification. So in case that info was filled before the driver
loaded and we've missed the notifications because of that the settings
will still be used.
With that place we now have to take care to properly handle a empty client
monitors config, so we don't trip over an uninitialized client monitors
config.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1488363154-6889-4-git-send-email-kraxel@redhat.com
When reading the monitor config fails, don't retry forever. If it fails
ten times in a row just give up to avoid the driver hangs. Also add a
small delay after each attempt, so the host has a chance to complete a
partial update.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1488363154-6889-3-git-send-email-kraxel@redhat.com
very old qxl hardware revisions (predating qxl ksm support by a few
years) supported a fixed list of video modes only. The list is still
provided by the virtual hardware, for backward compatibility reasons.
The qxl kms driver never ever looks at it, except for dumping it to
the kernel log at load time in case debug logging is enabled. Drop
that pointless code.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1488363154-6889-2-git-send-email-kraxel@redhat.com
This patch fixes the checkpatch issue:
CHECK: Logical continuations should be on the previous line.
Signed-off-by: Arushi Singhal <arushisinghal19971997@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
function prototype argument should have an identifier name as reported
by checkpatch.pl.
Signed-off-by: Arushi Singhal <arushisinghal19971997@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Revise lpfc version number to 11.2.0.10
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch addresses the smatch issues identified by Dan Carpenter
in http://www.spinics.net/lists/linux-scsi/msg105665.html
The issues are:
drivers/scsi/lpfc/lpfc_ct.c:943 lpfc_cmpl_ct_cmd_gft_id()
error: we previously assumed 'ndlp' could be null (see line 928)
Action: moved under if check
drivers/scsi/lpfc/lpfc_nvmet.c:1694 lpfc_nvmet_unsol_issue_abort()
error: we previously assumed 'ndlp' could be null (see line 1690)
Action: conditionalized arg in printf stmt
drivers/scsi/lpfc/lpfc_nvmet.c:1792 lpfc_nvmet_sol_fcp_issue_abort()
error: we previously assumed 'ndlp' could be null (see line 1788)
Action: conditionalized arg in printf stmt
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch addresses the smatch issues identified by Dan Carpenter
in http://www.spinics.net/lists/linux-scsi/msg105663.html
The issues are:
drivers/scsi/lpfc/lpfc_hbadisc.c:316 lpfc_dev_loss_tmo_handler()
warn: we tested 'vport->load_flag & 2' before and it was 'false'
Action: removed item from test
drivers/scsi/lpfc/lpfc_hbadisc.c:701 lpfc_work_done()
warn: test_bit() takes a bit number
Action: changed definition so bit number
drivers/scsi/lpfc/lpfc_hbadisc.c:2206 lpfc_mbx_cmpl_fcf_scan_read_fcf_rec()
error: uninitialized symbol 'vlan_id'.
drivers/scsi/lpfc/lpfc_hbadisc.c:2582 lpfc_mbx_cmpl_fcf_rr_read_fcf_rec()
error: uninitialized symbol 'vlan_id'.
drivers/scsi/lpfc/lpfc_hbadisc.c:2683 lpfc_mbx_cmpl_read_fcf_rec() error:
uninitialized symbol 'vlan_id'.
Action: initilized value
drivers/scsi/lpfc/lpfc_hbadisc.c:4025 lpfc_register_remote_port()
error: we previously assumed 'rdata' could be null (see line 4023)
Action: refactored check block
drivers/scsi/lpfc/lpfc_hbadisc.c:4613 lpfc_sli4_dequeue_nport_iocbs()
error: double unlock 'irq:'
Action: removed inner irq reference
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVME merge reverted diag port names to the physical port.
They should be the vport.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove nvme teardown calls that should not be there on sli3 devices
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Correct a merge error that had debug data printed twice for the
same element
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Without apriori understanding of what the define is, the name gives
a very different impression of what it is (a max delay value
for an EQ). Rename the define so it reflects what it is: the number
of EQ IDs that can be set in one instance of the MODIFY_EQ_DELAY
mbx command.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reworked Kconfig so that lfpc only requires the scsi stack.
NVME Initiator and NVME Target support can be enabled if
the other NVMe subsystems have been enabled.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph's prior patch missed the template for the sli3 adapters,
which is now the "no host reset" template. Add the transport
eh_timed_out handler to the no host reset template
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A previous change unilaterally removed the hba reset entry point
from the sli3 host template. This was done to allow tape devices
being used for back up from being removed. Why was this done ?
When there was non-responding device on the fabric, the error
escalation policy would escalate to the reset handler. When the
reset handler was called, it would reset the adapter, dropping
link, thus logging out and terminating all i/o's - on any target.
If there was a tape device on the same adapter that wasn't in
error, it would kill the tape i/o's, effectively killing the
tape device state. With the reset point removed, the adapter
reset avoided the fabric logout, allowing the other devices to
continue to operate unaffected. A hack - yes. Hint: we really
need a transport I_T nexus reset callback added to the eh process
(in between the SCSI target reset and hba reset points), so a
fc logout could occur to the one bad target only and stop the error
escalation process.
This patch commonizes the approach so it can be used for sli3 and sli4
adapters, but mandates the admin, via module parameter, specifically
identify which adapters the resets are to be removed for. Additionally,
bus_reset, which sends Target Reset TMFs to all targets, is also removed
from the template as it too has the same effect as the adapter reset.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
previous code did little more than log a message.
This patch adds abort path support, modeled after the SCSI code paths.
Currently addresses only the initiator path. Target path under
development, but stubbed out.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
nvme bufs get allocated even when the registration fails.
Move allocation into the rsgistration success path.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For both initiator and target: if WQ is full, return -EBUSY.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
