This platform is completely probed by device tree nowadays, so
we need to do a bigger cleanup removing all the non-DT codepaths.
This cleanup must however go in as a fix since it fixes a
regression.
Currently when Ux500 audio is enabled, dmesg complains like
this:
entry->name == "prealloc"
entry->name == "prealloc_max"
entry->name == "prealloc"
------------[ cut here ]------------
WARNING: CPU: 0 PID: 95 at ../fs/proc/generic.c:346
proc_register+0xf0/0x110
proc_dir_entry 'sub0/prealloc' already registered
(...)
entry->name == "prealloc_max"
------------[ cut here ]------------
WARNING: CPU: 0 PID: 95 at ../fs/proc/generic.c:346
proc_register+0xf0/0x110
proc_dir_entry 'sub0/prealloc_max' already registered
(...)
snd-soc-mop500 soc🔉 ab8500-codec-dai.0 <->
80124000.msp mapping ok
entry->name == "prealloc"
entry->name == "prealloc_max"
entry->name == "prealloc"
------------[ cut here ]------------
WARNING: CPU: 0 PID: 95 at ../fs/proc/generic.c:346
proc_register+0xf0/0x110
proc_dir_entry 'sub0/prealloc' already registered
(...)
entry->name == "prealloc_max"
------------[ cut here ]------------
WARNING: CPU: 0 PID: 95 at ../fs/proc/generic.c:346
proc_register+0xf0/0x110
proc_dir_entry 'sub0/prealloc_max' already registered
snd-soc-mop500 soc🔉 ab8500-codec-dai.1 <->
80125000.msp mapping ok
This is because PCMs are created twice for the same hardware,
and this happens because both "platform" and "CPU" DAI links
are specified.
But platform/CPU is an either/or pair, not a both/and pair.
This has maybe worked in the past, but it is causing trouble
now, so let us begin the cleanups by removing the platform
assignment and silencing the boot noise, and make a proper DT
cleanup for the next kernel cycle.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are new iterator macros that annotate whether the new or old
state should be used. This is better than using a state that depends on
whether it's called before or after swap. For clarity, also rename the
variables from $obj_state to (old,new)_$obj_state as well.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487256430-7625-6-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
This is a straightforward conversion that converts all the users of
get_existing_state in atomic core to use get_old_state or get_new_state
Changes since v1:
- Fix using the wrong state in drm_atomic_helper_update_legacy_modeset_state.
Changes since v2:
- Use the correct state in disable_outputs()
Changes since v3:
- Rebase for link status training.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/df91a9f9-005e-bcbd-1f74-03c38e1e21dd@linux.intel.com
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The CPPR (Current Processor Priority Register) of a XICS interrupt
presentation controller contains a value N, such that only interrupts
with a priority "more favoured" than N will be received by the CPU,
where "more favoured" means "less than". So if the CPPR has the value 5
then only interrupts with a priority of 0-4 inclusive will be received.
In theory the CPPR can support a value of 0 to 255 inclusive.
In practice Linux only uses values of 0, 4, 5 and 0xff. Setting the CPPR
to 0 rejects all interrupts, setting it to 0xff allows all interrupts.
The values 4 and 5 are used to differentiate IPIs from external
interrupts. Setting the CPPR to 5 allows IPIs to be received but not
external interrupts.
The CPPR emulation in the OPAL XICS implementation only directly
supports priorities 0 and 0xff. All other priorities are considered
equivalent, and mapped to a single priority value internally. This means
when using icp-opal we can not allow IPIs but not externals.
This breaks Linux's use of priority values when a CPU is hot unplugged.
After migrating IRQs away from the CPU that is being offlined, we set
the priority to 5, meaning we still want the offline CPU to receive
IPIs. But the effect of the OPAL XICS emulation's use of a single
priority value is that all interrupts are rejected by the CPU. With the
CPU offline, and not receiving IPIs, we may not be able to wake it up to
bring it back online.
The first part of the fix is in icp_opal_set_cpu_priority(). CPPR values
of 0 to 4 inclusive will correctly cause all interrupts to be rejected,
so we pass those CPPR values through to OPAL. However if we are called
with a CPPR of 5 or greater, the caller is expecting to be able to allow
IPIs but not external interrupts. We know this doesn't work, so instead
of rejecting all interrupts we choose the opposite which is to allow all
interrupts. This is still not correct behaviour, but we know for the
only existing caller (xics_migrate_irqs_away()), that it is the better
option.
The other part of the fix is in xics_migrate_irqs_away(). Instead of
setting priority (CPPR) to 0, and then back to 5 before migrating IRQs,
we migrate the IRQs before setting the priority back to 5. This should
have no effect on an ICP backend with a working set_priority(), and on
icp-opal it means we will keep all interrupts blocked until after we've
finished doing the IRQ migration. Additionally we wait for 5ms after
doing the migration to make sure there are no IRQs in flight.
Fixes: d74361881f ("powerpc/xics: Add ICP OPAL backend")
Cc: stable@vger.kernel.org # v4.8+
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Reported-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Tested-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
[mpe: Rewrote comments and change log, change delay to 5ms]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix not to update the iterator element, instead use list_del to remove
entry from the list.
This fixes the following coccinelle and static checker warning:
sound/soc/codecs/hdac_hdmi.c:1884:2-21:iterator with update on line
1885
sound/soc/codecs/hdac_hdmi.c:2011 hdac_hdmi_dev_remove()
error: potential NULL dereference 'port'.
Fixes: e0e5d3e5a53b('ASoC: hdac_hdmi: Add support for multiple ports to a PCM')
Reported-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Using pin list array iterator outside the iteration of the list can
point to dummy element, which can be invalid. So don't use pin variable
outside the pin list iteration.
This fixes the following coccinelle warning:
sound/soc/codecs/hdac_hdmi.c:1419:5-8: ERROR: invalid reference to the
index variable of the iterator
Fixes: 2acd8309a3a4('ASoC: hdac_hdmi: Add support to handle MST capable pin')
Reported-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After atomic commit, these macros should be used in place of
get_existing_state. Also after commit get_xx_state should no longer
be used because it may not have the required locks.
The calls to drm_atomic_get_existing_$obj_state should no longer be
used, and converted over to these new calls.
Changes since v1:
- Expand commit message.
- Deprecate get_existing_*_state functions in the documentation.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487256430-7625-4-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
This function becomes a lot simpler when having passed both the old and
new state to it. Looking at all callers, it seems that old_plane_state
is never NULL so the check can be dropped.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487256430-7625-3-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Without this I am getting the following messages at boot on my Trimslice:
tlv320aic23-codec 2-001a: Control not supported for path LLINEIN -> [NULL] -> Line Input
tlv320aic23-codec 2-001a: ASoC: no dapm match for LLINEIN --> NULL --> Line Input
tlv320aic23-codec 2-001a: ASoC: Failed to add route LLINEIN -> NULL -> Line Input
tlv320aic23-codec 2-001a: Control not supported for path RLINEIN -> [NULL] -> Line Input
tlv320aic23-codec 2-001a: ASoC: no dapm match for RLINEIN --> NULL --> Line Input
tlv320aic23-codec 2-001a: ASoC: Failed to add route RLINEIN -> NULL -> Line Input
tlv320aic23-codec 2-001a: Control not supported for path MICIN -> [NULL] -> Mic Input
tlv320aic23-codec 2-001a: ASoC: no dapm match for MICIN --> NULL --> Mic Input
tlv320aic23-codec 2-001a: ASoC: Failed to add route MICIN -> NULL -> Mic Input
tegra-snd-trimslice sound: tlv320aic23-hifi <-> 70002800.i2s mapping ok
Signed-off-by: Liviu Dudau <liviu@dudau.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
As the sampling frequency is supported by es8328 in slave mode,
add support for it in the corresponding operation.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are new iterator macros that annotate whether the new or old
state should be used. This is better than using a state that depends on
whether it's called before or after swap. For clarity, also rename the
variables from $obj_state to (old,new)_$obj_state as well.
Changes since v1:
- Use old/new_*_state for variable names as much as possible. (pinchartl)
- Expand commit message.
Changes since v2:
- Rebase on top of link training patches.
- free -> cleanup (pinchartl)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: http://patchwork.freedesktop.org/patch/msgid/aafa0d4d-474d-441f-3685-fa6c042ef37e@linux.intel.com
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
As the sampling frequency is supported by es8328 in slave mode,
add support for it in the corresponding operation.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The master and slave modes don't share the same table for MCLK/LRCLK
ratios. The slaves mode has bigger ratios that allow to use BCLK that
matche sampling frequency of 192khz.
This commit enables this rate only for slave mode, i.e it does not
declare this frequency in sysclk_contraints, resulting to an error in
master mode (not supported CLK).
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently most of the standard rates are supported by this driver.
Instead of defining each supported rate one by one, we use the SND macro
SNDRV_PCM_RATE_8000_48000. Also adds support for 88.2khz as the codec
supports it and the sys clocks are already supported.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In master mode, SCLK and LRCLK signals are generated by the CODEC when
any of the ADC/DAC are enabled. SCLK is derived from MCLK via a
programmable division set by BLK_DIV, LRCLK is derived from MCLK via
another programmable division set by ADCFsRatio/DACFsRatio.
In slave mode, SCLK and LRCLK signals are received as inputs and
supplied externally. LRCLK and SCLK must be synchronously derived from
MCLK with specific rates. The device can auto detect MCLK/LRCLK ratio
according to a predefined table. LRCLK/SCLK ratio is usually 64 (SCLK =
64 * LRCLK)
This commits adds support to let to device auto detect and decide which
ratio to use. The mclkdiv2 and BCLK_DIV ratio and put to zero.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Many boards form list of spi_board_info entries depending on config,
and it is possible to end up with empty list. Do not report error
in such cases.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Generic device properties support statically defined property sets. For
them to be usable, we need to attach these property sets before devices
are registered and probed. Allowing to attach property list to
spi_board_info structure will allow non-ACPI non-DT boards switch to using
generic properties and get rid of custom platform data.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Our GICv3 emulation always presents ICC_SRE_EL1 with DIB/DFB set to
zero, which implies that there is a way to bypass the GIC and
inject raw IRQ/FIQ by driving the CPU pins.
Of course, we don't allow that when the GIC is configured, but
we fail to indicate that to the guest. The obvious fix is to
set these bits (and never let them being changed again).
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When invalidating guest TLBs, special care must be taken to
actually shoot the guest TLBs and not the host ones if we're
running on a VHE system. This is controlled by the HCR_EL2.TGE
bit, which we forget to clear before invalidating TLBs.
Address the issue by introducing two wrappers (__tlb_switch_to_guest
and __tlb_switch_to_host) that take care of both the VTTBR_EL2
and HCR_EL2.TGE switching.
Reported-by: Tomasz Nowicki <tnowicki@caviumnetworks.com>
Tested-by: Tomasz Nowicki <tnowicki@caviumnetworks.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Introduces linaro prefix and adds bindings for ARM TrustZone based OP-TEE
implementation.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Replaced x == NULL with !x, by using the following coccinelle script:
@disable is_null@
expression e;
@@
-e==NULL
+!e
This patch fixes the checkpatch issue.
Signed-off-by: Varsha Rao <rvarsha016@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Correct the spelling of initialize. This patch fixes the checkpatch
issue.
Signed-off-by: Varsha Rao <rvarsha016@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Usage of unsigned int is preferred over unsigned and this patch fixes the
checkpatch issue.
Signed-off-by: Varsha Rao <rvarsha016@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the checkpatch issue by removing the Free Software
Foundation's mailing address from the sample GPL notice. Because the FSF
has changed address in the past, and may change again. Linux already
includes a copy of the GPL.
Signed-off-by: Varsha Rao <rvarsha016@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Used kernel preferred block commenting style, to fix the following
checkpatch issue:
WARNING: Block comments use a trailing */ on a separate line
Signed-off-by: Varsha Rao <rvarsha016@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replaced 'uint32_t' with kernel type u32, to fix the checkpatch issue.
Signed-off-by: Varsha Rao <rvarsha016@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Line over 80 characters are split to fix the following checkpatch issue:
WARNING: line over 80 characters
Signed-off-by: Varsha Rao <rvarsha016@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removed parentheses on the right hand side of assignment, as they are
not required. The following coccinelle script is used to fix this issue:
@@
binary operator op = {<<,>>,+,/};
local idexpression id;
expression e1, e2;
@@
id =
-(
e1 op e2
-)
Signed-off-by: Varsha Rao <rvarsha016@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SSI8 is is sharing pin with SSI7, and nothing to do for SSI_MODEx.
It is special pin and it needs special settings whole system,
but we can't confirm it, because we never have SSI8 available board.
This patch fixup SSI_MODEx settings error for SSI8 on connection test,
but should be confirmed behavior on real board in the future.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
drivers/staging/media/atomisp/i2c/imx/../ov8858.c:2199:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/staging/media/atomisp/platform/clock/vlv2_plat_clock.c:248:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/staging/media/atomisp/i2c/ov2722.c:1352:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/staging/media/atomisp/i2c/ov5693/ov5693.c:2066:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/staging/media/atomisp/i2c/lm3554.c:986:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/staging/media/atomisp/i2c/mt9m114.c:1946:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/staging/media/atomisp/i2c/gc0310.c:1470:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/staging/media/atomisp/i2c/imx/imx.c:2486:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/staging/media/atomisp/i2c/gc2235.c:1208:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/staging/media/atomisp/i2c/ap1302.c:1250:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some SPI nodes are missing #address-cells and #size-cells. This is
causing warning at device tree compilation when some SPI device
sub-nodes are defined.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Per PCI specification, Configuration Register has different types (RO,
RW, RW1C, Rsvd). For RO Register bits are read-only and cannot be
altered by software. For RW1C Register bits indicate status when read.
A Set bit indicates a status event which is Cleared by writing a 1b.
Writing a 0b to RW1C bits has no effect. Reserved Register is for future
implementations, and they are read-only and must return zero when read.
Current vGPU configuration write emulation just copy the value as it is.
So we haven't emulated RO, RW1C and Rsvd Registers correctly. This patch
is following the Spec to correct emulation logic. We add a function
vgpu_cfg_mem_write to wrap the access to vGPU configuration memory.
The write function uses a RW Register bitmap to avoid RO bits be
overwritten, and emulate RW1C behavior for the particular status Register.
v2:
new = src[i] --> new = src[i] & mask (zhenyu)
Signed-off-by: Changbin Du <changbin.du@intel.com>
Cc: Xiaoguang Chen <xiaoguang.chen@intel.com>
Cc: Zhiyuan Lv <zhiyuan.lv@intel.com>
Cc: Min He <min.he@intel.com>
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Currently i915 has a request replay mechanism which can make sure
the request can be replayed after a GPU reset. With this mechanism,
gvt should wait until the GVT request seqno passed before complete
the current workload. So that there should be a context switch interrupt
come before gvt free the workload. In this way, workload lifecylce
matches with the i915 request lifecycle. The workload can only be freed
after the request is completed.
v2: use gvt_dbg_sched instead of gvt_err to print when wait again
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Tighten the depends on the various AllWinn SoCs so we don't
inadvertantly get clock drivers when we're not wanting them
like 32 bit SoC clocks for 64 bit configs. Ensure there's
still test coverage though.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
