The A31 Hummingbird has a mini USB OTG port, and uses GPIO pins from the
SoC for ID pin and VBUS detection and VBUS control. The PMIC can also do
VBUS detection and control.
Here we prefer to use the PMIC's DRIVEVBUS function to control VBUS for
USB OTG, as that is the hardware default.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In the past, all the MMC pins had
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
which was actually a no-op. We were relying on U-boot to set the bias
pull up for us. These properties were removed as part of the fix up to
actually support no bias on the pins. During the transition some boards
experienced regular MMC time-outs during normal operation, while others
completely failed to initialize the SD card.
Given that MMC starts in open-drain mode and the pull-ups are required,
it's best to enable it for all the pin settings.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Fixed warning reported by kbuild test robot.
When reading current resource usage value, when no resources are
allocated, its possible that it can report a uninitialized value
for current resource usage.
This fix avoids it by initializing it to zero as no resource is
allocated.
Signed-off-by: Parav Pandit <pandit.parav@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The access to fd from anon_inode is always failed because there is
no set xattr operations. So this patch fixes to ignore private
inode including anon_inode for file functions.
It was only ignored for smack_file_receive() to share dma-buf fd,
but dma-buf has other functions like ioctl and mmap.
Reference: https://lkml.org/lkml/2015/4/17/16
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Since 4b936885a (v2.6.32) all inodes on sockfs and pipefs are disconnected.
It caused filesystem specific code in smack_d_instantiate to be skipped,
because all inodes on those pseudo filesystems were treated as root inodes.
As a result all sockfs inodes had the Smack label set to floor.
In most cases access checks for sockets use socket_smack data so the inode
label is not important. But there are special cases that were broken.
One example would be calling fcntl with F_SETOWN command on a socket fd.
Now smack_d_instantiate expects all pipefs and sockfs inodes to be
disconnected and has the logic in appropriate place.
Signed-off-by: Rafal Krypa <r.krypa@samsung.com>
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
smack_file_open() is first checking the capability of calling subject,
this check will skip the SMACK logging for success case. Use smk_tskacc()
for proper logging and SMACK access check.
Signed-off-by: Himanshu Shukla <himanshu.sh@samsung.com>
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
In smack_from_secattr function,"smack_known_list" is being traversed
using list_for_each_entry macro, although it is a rcu protected
structure. So it should be traversed using "list_for_each_entry_rcu"
macro to fetch the rcu protected entry.
Signed-off-by: Vishal Goel <vishal.goel@samsung.com>
Signed-off-by: Himanshu Shukla <himanshu.sh@samsung.com>
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
There is race condition issue while freeing the i_security blob in SMACK
module. There is existing condition where i_security can be freed while
inode_permission is called from path lookup on second CPU. There has been
observed the page fault with such condition. VFS code and Selinux module
takes care of this condition by freeing the inode and i_security field
using RCU via call_rcu(). But in SMACK directly the i_secuirty blob is
being freed. Use call_rcu() to fix this race condition issue.
Signed-off-by: Himanshu Shukla <himanshu.sh@samsung.com>
Signed-off-by: Vishal Goel <vishal.goel@samsung.com>
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
smk_copy_rules() and smk_copy_relabel() are initializing list_head though
they have been initialized already in new_task_smack() function. Delete
repeated initialization.
Signed-off-by: Himanshu Shukla <himanshu.sh@samsung.com>
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
"smk_set_access()" function adds a new rule entry in subject label specific
list(rule_list) and in global rule list(smack_rule_list) both. Mutex lock
(rule_lock) is used to avoid simultaneous updates. But this lock is subject
label specific lock. If 2 processes tries to add different rules(i.e with
different subject labels) simultaneously, then both the processes can take
the "rule_lock" respectively. So it will cause a problem while adding
entries in master rule list.
Now a new mutex lock(smack_master_list_lock) has been taken to add entry in
smack_rule_list to avoid simultaneous updates of different rules.
Signed-off-by: Vishal Goel <vishal.goel@samsung.com>
Signed-off-by: Himanshu Shukla <himanshu.sh@samsung.com>
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Fix the issue of wrong SMACK label (SMACK64IPIN) update when a second bind
call is made to same IP address & port, but with different SMACK label
(SMACK64IPIN) by second instance of server. In this case server returns
with "Bind:Address already in use" error but before returning, SMACK label
is updated in SMACK port-label mapping list inside smack_socket_bind() hook
To fix this issue a new check has been added in smk_ipv6_port_label()
function before updating the existing port entry. It checks whether the
socket for matching port entry is closed or not. If it is closed then it
means port is not bound and it is safe to update the existing port entry
else return if port is still getting used. For checking whether socket is
closed or not, one more field "smk_can_reuse" has been added in the
"smk_port_label" structure. This field will be set to '1' in
"smack_sk_free_security()" function which is called to free the socket
security blob when the socket is being closed. In this function, port entry
is searched in the SMACK port-label mapping list for the closing socket.
If entry is found then "smk_can_reuse" field is set to '1'.Initially
"smk_can_reuse" field is set to '0' in smk_ipv6_port_label() function after
creating a new entry in the list which indicates that socket is in use.
Signed-off-by: Vishal Goel <vishal.goel@samsung.com>
Signed-off-by: Himanshu Shukla <himanshu.sh@samsung.com>
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Permission denied error comes when 2 IPv6 servers are running and client
tries to connect one of them. Scenario is that both servers are using same
IP and port but different protocols(Udp and tcp). They are using different
SMACK64IPIN labels.Tcp server is using "test" and udp server is using
"test-in". When we try to run tcp client with SMACK64IPOUT label as "test",
then connection denied error comes. It should not happen since both tcp
server and client labels are same.This happens because there is no check
for protocol in smk_ipv6_port_label() function while searching for the
earlier port entry. It checks whether there is an existing port entry on
the basis of port only. So it updates the earlier port entry in the list.
Due to which smack label gets changed for earlier entry in the
"smk_ipv6_port_list" list and permission denied error comes.
Now a check is added for socket type also.Now if 2 processes use same
port but different protocols (tcp or udp), then 2 different port entries
will be added in the list. Similarly while checking smack access in
smk_ipv6_port_check() function, port entry is searched on the basis of
both port and protocol.
Signed-off-by: Vishal Goel <vishal.goel@samsung.com>
Signed-off-by: Himanshu Shukla <Himanshu.sh@samsung.com>
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Add the rcu synchronization mechanism for accessing smk_ipv6_port_list
in smack IPv6 hooks. Access to the port list is vulnerable to a race
condition issue,it does not apply proper synchronization methods while
working on critical section. It is possible that when one thread is
reading the list, at the same time another thread is modifying the
same port list, which can cause the major problems.
To ensure proper synchronization between two threads, rcu mechanism
has been applied while accessing and modifying the port list. RCU will
also not affect the performance, as there are more accesses than
modification where RCU is most effective synchronization mechanism.
Signed-off-by: Vishal Goel <vishal.goel@samsung.com>
Signed-off-by: Himanshu Shukla <himanshu.sh@samsung.com>
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
MAD and HFI1 have different naming convention, this patch
simplifies and unifies their defines and names.
As part of cleanup, the HFI1 _NUM() macro and command indexes
were removed (controversial). This will cause intentional (and
arguably unnecessary) breakage to the PSM user space library.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Move hfi1 ioctl definitions to a new header which can be included by
both the hfi1 and qib drivers to avoid a duplicate enum definition
as shown in this build error for qib:
CC [M] drivers/infiniband/hw/qib/qib_sysfs.o
In file included from ./include/uapi/rdma/rdma_user_ioctl.h:39:0,
from include/uapi/rdma/ib_user_mad.h:38,
from include/rdma/ib_mad.h:43,
from include/rdma/ib_pma.h:38,
from drivers/infiniband/hw/qib/qib_mad.h:37,
from drivers/infiniband/hw/qib/qib_init.c:49:
./include/uapi/rdma/hfi/hfi1_user.h:370:2: error: redeclaration of
enumerator ‘ur_rcvhdrtail’
ur_rcvhdrtail = 0,
Move hfi1 structures to separate file to avoid this failure.
The actual move of the ioctl definitions comes in a follow on patch.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch provides one common file (rdma_user_ioctl.h)
for all RDMA UAPI IOCTLs.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The node name for the power seq pin is mmc2@0 like the mmc2_pins_a one.
This makes the original node (mmc2_pins_a) scrapped out of the dtb and
result in a unusable eMMC if U-Boot didn't configured the pins to the
correct functions.
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
If srp_transfer_data fails within ibmvscsis_write_pending, then
the most likely scenario is that the client timed out the op and
removed the TCE mapping. Thus it will loop forever retrying the
op that is pretty much guaranteed to fail forever. A better return
code would be EIO instead of EAGAIN.
Cc: stable@vger.kernel.org
Reported-by: Steven Royer <seroyer@linux.vnet.ibm.com>
Tested-by: Steven Royer <seroyer@linux.vnet.ibm.com>
Signed-off-by: Bryant G. Ly <bgly@us.ibm.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Now that we disable the display engine by default, we need to re-enable
it for the Hummingbird A31, which already had its display pipeline
enabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
While we now support the internal display pipeline found on sun6i, it
is possible that we are unable to enable the display for some boards,
due to a lack of drivers for the panels or bridges found on them. If
the display pipeline is enabled, the driver will try to enable, and
possibly screw up the simple framebuffer U-boot had configured.
Disable the display pipeline by default.
Fixes: 6d0e5b70be ("ARM: dts: sun6i: Add device nodes for first
display pipeline")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
MUSB driver now has runtime PM support, but the debugfs driver misses
the PM _get/_put() calls, which could cause MUSB register access
failure.
Cc: stable@vger.kernel.org # 4.9+
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Preserve chip operation mode if no mode is specified via devicetree. This
enables operation when chip configuration is done by BIOS/ROMMON.
Signed-off-by: Alexander Koch <mail@alexanderkoch.net>
Acked-by: Michael Hornung <mhornung.linux@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Track the user visible fields of a CPU feature register. This will be
used for exposing the value to the userspace. All the user visible
fields of a feature register will be passed on as it is, while the
others would be filled with their respective safe value.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Add support for operation modes 1-3 of the ADC128D818 (see datasheet sec.
8.4.1). These differ in the number and type of the available input signals,
requiring the driver to selectively hide sysfs nodes according to the
operation mode configured via devicetree.
Signed-off-by: Alexander Koch <mail@alexanderkoch.net>
Acked-by: Michael Hornung <mhornung.linux@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add a helper to extract the register field from a given
instruction.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Define helper macros to extract op0, op1, CRn, CRm & op2
for a given sys_reg id. While at it remove the explicit
masking only used for Op0.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Document the rules for choosing the safe value for different types
of features.
Cc: Dave Martin <dave.martin@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch does the following clean ups :
1) All undescribed fields of a register are now treated as 'strict'
with a safe value of 0. Hence we could leave an empty table for
describing registers which are RAZ.
2) ID_AA64DFR1_EL1 is RAZ and should use the table for RAZ register.
3) ftr_generic32 is used to represent a register with a 32bit feature
value. Rename this to ftr_singl32 to make it more obvious. Since
we don't have a 64bit singe feature register, kill ftr_generic.
Based on a patch by Mark Rutland.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We currently have some RAZ fields described explicitly in our
arm64_ftr_bits arrays. These are inconsistently commented, grouped,
and/or applied, and maintaining these is error-prone.
Luckily, we don't need these at all. We'll never need to inspect RAZ
fields to determine feature support, and init_cpu_ftr_reg() will ensure
that any bits without a corresponding arm64_ftr_bits entry are treated
as RES0 with strict matching requirements. In check_update_ftr_reg()
we'll then compare these bits from the relevant cpuinfo_arm64
structures, and need not store them in a arm64_ftr_reg.
This patch removes the unnecessary arm64_ftr_bits entries for RES0 bits.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Any fields not defined in an arm64_ftr_bits entry are propagated to the
system-wide register value in init_cpu_ftr_reg(), and while we require
that these strictly match for the sanity checks, we don't update them in
update_cpu_ftr_reg().
Generally, the lack of an arm64_ftr_bits entry indicates that the bits
are currently RES0 (as is the case for the upper 32 bits of all
supposedly 32-bit registers).
A better default would be to use zero for the system-wide value of
unallocated bits, making all register checking consistent, and allowing
for subsequent simplifications to the arm64_ftr_bits arrays.
This patch updates init_cpu_ftr_reg() to treat unallocated bits as RES0
for the purpose of the system-wide safe value. These bits will still be
sanity checked with strict match requirements, as is currently the case.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Implement operation mode selection using the optional 'ti,mode' devicetree
property (see [1]). The ADC128D818 supports four operation modes differing
in the number and type of input readings (see datasheet, sec. 8.4.1), of
which mode 0 is the default.
We only add handling of the 'ti,mode' property here, the driver still
supports nothing else than the default mode 0.
[1] Documentation/devicetree/bindings/hwmon/adc128d818.txt
Signed-off-by: Alexander Koch <mail@alexanderkoch.net>
Acked-by: Michael Hornung <mhornung.linux@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add bindings documentation for the ADC128D818 driver, featuring default I2C
properties along with the optional 'mode' property for chip operation mode
selection (see datasheet, sec. 8.4.1).
Signed-off-by: Alexander Koch <mail@alexanderkoch.net>
Acked-by: Michael Hornung <mhornung.linux@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
[groeck: Fixed whitespace error]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
tmp401 separately read/wrote high and low bytes of temperature values while
the hardware supports reading/writing those values in one operation. Driver
has been modified to use word operations where possible.
Tested with a tmp432 sensor on a mips64 platform.
Signed-off-by: Jeroen De Wachter <jeroen.de_wachter.ext@nokia.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Writes into limit attributes can overflow due to multplications and
additions with unbound input values. Writing into fan limit attributes
can result in a crash with a division by zero if very large values are
written and the fan divider is larger than 1.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Writes into limit attributes can overflow due to additions and
multiplications with unchecked parameters.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Writes into voltage limit, temperature limit, temperature hysteresis,
and temperature zone attributes can overflow due to unclamped parameters
to multiplications, additions, and subtractions.
Cc: Juerg Haefliger <juergh@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Hayes Wang says:
====================
r8152: fix autosuspend issue
Avoid rx is split into two parts when runtime suspend occurs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pause the rx and make sure the rx fifo is empty when the autosuspend
occurs.
If the rx data comes when the driver is canceling the rx urb, the host
controller would stop getting the data from the device and continue
it after next rx urb is submitted. That is, one continuing data is
split into two different urb buffers. That let the driver take the
data as a rx descriptor, and unexpected behavior happens.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split rtl8152_suspend() into rtl8152_system_suspend() and
rtl8152_rumtime_suspend().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed the following checkpatch warnings by deleting blank lines
Blank lines aren't necessary before a close brace '}'
Blank lines aren't necessary after an open brace '{'
Please don't use multiple blank lines
Signed-off-by: Scott Matheina <scott@matheina.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed Alignment should match open parenthesis from checkpatch
Signed-off-by: Scott Matheina <scott@matheina.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed Alignment should match open parenthesis checkpatch CHECK
Signed-off-by: Scott Matheina <scott@matheina.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed Alignment should match open parenthesis checkpatch CHECK
Signed-off-by: Scott Matheina <scott@matheina.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes the space coding styles issues complained by checkpatch.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This should fix the indentation issues found by checkpatch.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
