Show length of analyzed sample time and rate of idle task running.
This also takes care of time range given by --time option.
$ perf sched timehist -sI | tail
Samples do not have callchains.
Idle stats:
CPU 0 idle for 930.316 msec ( 92.93%)
CPU 1 idle for 963.614 msec ( 96.25%)
CPU 2 idle for 885.482 msec ( 88.45%)
CPU 3 idle for 938.635 msec ( 93.76%)
Total number of unique tasks: 118
Total number of context switches: 2337
Total run time (msec): 3718.048
Total scheduling time (msec): 1001.131 (x 4)
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20161222060350.17655-3-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Commit f1c131b454: "crypto: xts - Convert to skcipher" now fails
the setkey operation if the AES key is the same as the tweak key.
Previously this check was only done if FIPS mode is enabled. Now this
check is also done if weak key checking was requested. This is
reasonable, but since we were using the dummy key which was a constant
series of 0x42 bytes, it now caused dummy encrpyption test mode to
fail.
Fix this by using 0x42... and 0x24... for the two keys, so they are
different.
Fixes: f1c131b454
Cc: stable@vger.kernel.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Currently gpio modules are runtime-resumed at probe time. This means the
gpio module will be active all the time (except during system suspend,
if not configured as a wake-up source).
While an R-Car Gen2 gpio module retains pins configured for output at
the requested level while put in standby mode, gpio register cannot be
accessed while suspended. Unfortunately pm_runtime_get_sync() cannot be
called from all contexts where gpio register access is needed. Hence
move the Runtime PM handling from probe/remove time to gpio request/free
time, which is probably the best we can do.
On r8a7791/koelsch, gpio modules 0, 1, 3, and 4 are now suspended during
normal use (gpio2 is used for LEDs and regulators, gpio5 for keys, gpio6
for SD-Card CD & WP, gpio7 for keys and regulators).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[Niklas: s/gpio_to_priv(chip)/gpiochip_get_data(chip)/]
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This enables Runtime PM handling for interrupts.
By setting the parent_device in struct irq_chip genirq will call the
pm_runtime_get/put APIs when an IRQ is requested/freed.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The patch introducing the g5 pinctrl driver implemented a smattering of
pins to flesh out the implementation of the core and provide bare-bones
support for some OpenPOWER platforms and the AST2500 evaluation board.
Now, update the bindings document to reflect the complete functionality
and implement the necessary pin configuration tables in the driver.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull networking fixes from David Miller:
1) Various ipvlan fixes from Eric Dumazet and Mahesh Bandewar.
The most important is to not assume the packet is RX just because
the destination address matches that of the device. Such an
assumption causes problems when an interface is put into loopback
mode.
2) If we retry when creating a new tc entry (because we dropped the
RTNL mutex in order to load a module, for example) we end up with
-EAGAIN and then loop trying to replay the request. But we didn't
reset some state when looping back to the top like this, and if
another thread meanwhile inserted the same tc entry we were trying
to, we re-link it creating an enless loop in the tc chain. Fix from
Daniel Borkmann.
3) There are two different WRITE bits in the MDIO address register for
the stmmac chip, depending upon the chip variant. Due to a bug we
could set them both, fix from Hock Leong Kweh.
4) Fix mlx4 bug in XDP_TX handling, from Tariq Toukan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: stmmac: fix incorrect bit set in gmac4 mdio addr register
r8169: add support for RTL8168 series add-on card.
net: xdp: remove unused bfp_warn_invalid_xdp_buffer()
openvswitch: upcall: Fix vlan handling.
ipv4: Namespaceify tcp_tw_reuse knob
net: korina: Fix NAPI versus resources freeing
net, sched: fix soft lockup in tc_classify
net/mlx4_en: Fix user prio field in XDP forward
tipc: don't send FIN message from connectionless socket
ipvlan: fix multicast processing
ipvlan: fix various issues in ipvlan_process_multicast()
The patch introducing the g4 pinctrl driver implemented a smattering of
pins to flesh out the implementation of the core and provide bare-bones
support for some OpenPOWER platforms. Now, update the bindings document
to reflect the complete functionality and implement the necessary pin
configuration tables in the driver.
Cc: Timothy Pearson <tpearson@raptorengineering.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The System Control Unit IP block in the Aspeed SoCs is typically where
the pinmux configuration is found, but not always. A number of pins
depend on state in one of LPC Host Control (LHC) or SoC Display
Controller (GFX) IP blocks, so the Aspeed pinmux drivers should have the
means to adjust these as necessary.
We use syscon to cast a regmap over the GFX and LPC blocks, which is
used as an arbitration layer between the relevant driver and the pinctrl
subsystem. The regmaps are then exposed to the SoC-specific pinctrl
drivers by phandles in the devicetree, and are selected during a mux
request by querying a new 'ip' member in struct aspeed_sig_desc.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reference the SoC-specific compatible string in the examples as
required.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current driver code gives the crash or gets hang while switching
the CPU frequency some time. The APSS CPU Clock divider is not glitch
free so it the APPS clock need to be switched for stable clock during
the change.
This patch adds the frequency change notifier for APSS CPU clock. It
changes the parent of this clock to stable PLL FEPLL500 for
PRE_RATE_CHANGE event. This event will be generated before actual
clock set operations. The clock set operation will again change its
corresponding parent by getting the same from frequency table.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
[sboyd@codeaurora.org: Indent less in probe]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
msleep (1~20) may not do what the caller intends, and will often sleep
longer. (~20 ms actual sleep for any value given in the 1~20ms range) This
is not the desired behaviour for many cases like device resume time, device
suspend time, device enable time, etc. Thus, change msleep to usleep_range
for precise wakeups.
Signed-off-by: Aniroop Mathur <a.mathur@samsung.com>
Acked by: Albert Zhang <xu.zhang@bosch-sensortec.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since F03 is a boolean, "depends" on symbols that can be modules
do not work quite right. We can enable F03 if SERIO is built-in or
if both RMI core and SERIO core are modules. If SERIO core is module,
but RMI is built-in, we'll get:
drivers/built-in.o: In function `rmi_f03_attention':
rmi_f03.c:(.text+0xf8ef8): undefined reference to `serio_interrupt'
rmi_f03.c:(.text+0xf8fbd): undefined reference to `serio_interrupt'
drivers/built-in.o: In function `rmi_f03_remove':
rmi_f03.c:(.text+0xf9082): undefined reference to `serio_unregister_port'
drivers/built-in.o: In function `rmi_f03_probe':
rmi_f03.c:(.text+0xf9260): undefined reference to `__serio_register_port'
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
currently the controllers get the same product id as the wireless
receiver. However the controllers actually have their own product id.
The patch makes the driver expose the same product id as the windows
driver.
This improves compatibility when running applications with WINE.
see https://github.com/paroj/xpad/issues/54
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In the actual implementation ether_addr_equal function tests for equality to 0
when returning. It seems in commit 0d74c4 it is somehow overlooked to change
this operator to reflect the actual function.
Signed-off-by: Cihangir Akturk <cakturk@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The 80211.tmpl DocBook file was removed in commit 819bf59376 ("docs-rst:
sphinxify 802.11 documentation"), but the 80211.xml target was re-added to
the Makefile by commit 7ddedebb03 ("ALSA: doc: ReSTize
writing-an-alsa-driver document"), leading to a failure when building the
documentation:
*** No rule to make target 'Documentation/DocBook/80211.xml', needed by
'Documentation/DocBook/80211.aux.xml'.
cc: stable@vger.kernel.org
Signed-off-by: John Brooks <john@fastquake.com>
Mea-culpa-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
kn->priv which is a void * is used as a RCU pointer by cgroup. When
dereferencing it, it was passing kn->priv to rcu_derefreence() without
casting it into a RCU pointer triggering address space mismatch
warning from sparse. Fix them.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Acked-by: Zefan Li <lizefan@huawei.com>
get/put_css_set() get exposed in cgroup-internal.h in the process.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Acked-by: Zefan Li <lizefan@huawei.com>
Now that the v1 mount code is split into separate functions, move them
to kernel/cgroup/cgroup-v1.c along with the mount option handling
code. As this puts all v1-only kernfs_syscall_ops in cgroup-v1.c,
move cgroup1_kf_syscall_ops to cgroup-v1.c too.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Acked-by: Zefan Li <lizefan@huawei.com>
Currently, cgroup_kf_syscall_ops is shared by v1 and v2 and the
specific methods test the version and take different actions. Split
out v1 functions and put them in cgroup1_kf_syscall_ops and remove the
now unnecessary explicit branches in specific methods.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Acked-by: Zefan Li <lizefan@huawei.com>
While sharing some mechanisms, the mount paths of v1 and v2 are
substantially different. Their implementations were mixed in
cgroup_mount(). This patch splits them out so that they're easier to
follow and organize.
This patch causes one functional change - the WARN_ON(new_sb) gets
lost. This is because the actual mounting gets moved to
cgroup_do_mount() and thus @new_sb is no longer accessible by default
to cgroup1_mount(). While we can add it as an explicit out parameter
to cgroup_do_mount(), this part of code hasn't changed and the warning
hasn't triggered for quite a while. Dropping it should be fine.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Acked-by: Zefan Li <lizefan@huawei.com>
cgroup.c is getting too unwieldy. Let's move out cgroup v1 specific
code along with the debug controller into kernel/cgroup/cgroup-v1.c.
v2: cgroup_mutex and css_set_lock made available in cgroup-internal.h
regardless of CONFIG_PROVE_RCU.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Acked-by: Zefan Li <lizefan@huawei.com>
They're growing to be too many and planned to get split further. Move
them under their own directory.
kernel/cgroup.c -> kernel/cgroup/cgroup.c
kernel/cgroup_freezer.c -> kernel/cgroup/freezer.c
kernel/cgroup_pids.c -> kernel/cgroup/pids.c
kernel/cpuset.c -> kernel/cgroup/cpuset.c
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Acked-by: Zefan Li <lizefan@huawei.com>
Reorder css_set fields so that they're roughly in the order of how hot
they are. The rough order is
1. the actual csses
2. reference counter and the default cgroup pointer.
3. task lists and iterations
4. fields used during merge including css_set lookup
5. the rest
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Acked-by: Zefan Li <lizefan@huawei.com>
cgroup_pid_fry() was added to mangle cgroup.procs pid listing order on
v2 to make it clear that the output is not sorted. Now that v2 now
uses a separate "cgroup.procs" read method, this is no longer used.
Remove it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Acked-by: Zefan Li <lizefan@huawei.com>
On v1, "tasks" and "cgroup.procs" are expected to be sorted which
makes the implementation expensive and unnecessarily complicated
involving result cache management.
v2 doesn't have the sorting requirement, so it can just iterate and
print processes one by one. seq_files are either read sequentially or
reset to position zero, so the implementation doesn't even need to
worry about seeking.
This keeps the css_task_iter across multiple read(2) calls and
migrations of new processes always append won't miss processes which
are newly migrated in before each read(2).
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Acked-by: Zefan Li <lizefan@huawei.com>
Pipe the newly added kernfs->open/release() callbacks through cftype.
While at it, as cleanup operations now can be performed from
->release() instead of ->seq_stop(), make the latter optional.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Acked-by: Zefan Li <lizefan@huawei.com>
Add ->open/release() methods to kernfs_ops. ->open() is called when
the file is opened and ->release() when the file is either released or
severed. These callbacks can be used, for example, to manage
persistent caching objects over multiple seq_file iterations.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Acked-by: Zefan Li <lizefan@huawei.com>
More kernfs_open_file->mutex synchronized flags are planned to be
added. Convert ->mmapped to a bitfield in preparation.
While at it, make kernfs_fop_mmap() use "true" instead of "1" on
->mmapped.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Acked-by: Zefan Li <lizefan@huawei.com>
Use symbolic names MM_TSB_BASE and MM_TSB_HUGE instead of numeric values
0 and 1 in __tsb_context_switch. Code cleanup only, no functional change.
Suggested-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trying to initialize eMMC slot as SDIO or SD cause failure in n900 port of
qemu. eMMC itself is not detected and is not working.
Real Nokia N900 harware does not have this problem. As eMMC is really not
SDIO or SD based such change is harmless and will fix support for qemu.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 5d080aa306 ("ARM: dts: dra72: Add separate dtsi for tps65917")
added a separate dtsi for dra72-evm-tps65917 moving all the voltage supplies
to this file. But it missed adding voltage supplies to usb_phy, mmc,
dss and deleted from dra72-evm-common.dtsi. Adding the voltage supply
phandles to these nodes in dra72-evm-tps65917.dtsi
Fixes: 5d080aa306 ("ARM: dts: dra72: Add separate dtsi for tps65917")
Reported-by: Carlos Hernandez <ceh@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
USB2 port can be operated in dual-role mode but till we
have dual-role support in dwc3 driver let's limit this
port to peripheral mode.
If we don't do so it defaults to host mode. USB1 port
is meant for host only operation and we don't want
both ports in host only mode.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
VBUS detection is available on the board via the palmas PMIC.
Use extcon-palmas driver instead of extcon-gpio-usb driver.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Specify the power button interrupt number which is from the datasheet.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add interrupt specifiers for USB and AC charger input. Interrupt numbers
are from the datasheet.
Fix wrong property for compatible string.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Interrupt numbers are from the datasheet, so no need to keep them in
the ABI. Use the number in the DT file.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use 'interrupt-names' for getting the charger interrupt number.
Fixes: 1934e89a76 ("ARM: dts: am335x: Add the charger interrupt")
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Issue caught with static analysis tool:
"Dangerous usage of 'name' (strncpy doesn't always 0-terminate it)"
Use strlcpy _includes_ the NUL terminator, and strlcat() which ensures
that it won't overflow the buffer.
Reported-by: Maninder Singh <maninder1.s@samsung.com>
Signed-off-by: Vaneet Narang <v.narang@samsung.com>
CC: Russell King <linux@armlinux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The commit 55ee7017ee ("arm: omap2: board-generic: use
omap4_local_timer_init for AM437x") unintentionally changes the
clocksource devices for AM437x from OMAP GP Timer to SyncTimer32K.
Unfortunately, the SyncTimer32K is starving from frequency deviation
as mentioned in commit 5b5c013591 ("ARM: OMAP2+: AM43x: Use gptimer
as clocksource") and, as reported by Franklin [1], even its monotonic
nature is under question (most probably there is a HW issue, but it's
still under investigation).
Taking into account above facts It's reasonable to rollback to the use
of omap3_gptimer_timer_init().
[1] http://www.spinics.net/lists/linux-omap/msg127425.html
Fixes: 55ee7017ee ("arm: omap2: board-generic: use
omap4_local_timer_init for AM437x")
Reported-by: Cooper Jr., Franklin <fcooper@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes: ("ab8dd3aed0 ARM: DTS: Add minimal Support for Logic PD
DM3730 SOM-LV")
This adds the dts file into the Makefile. This should have been included in
the original patch.
V2: Update patch description - same source code
V1: Original patch
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 55871eb6e2 ("ARM: dts: dra7: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 55871eb6e2 ("ARM: dts: dra7: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 06bfb9c199 ("ARM: dts: dm816x: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 06bfb9c199 ("ARM: dts: dm816x: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 76155b378c ("ARM: dts: dm814x: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 76155b378c ("ARM: dts: dm814x: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixing the gmac4 mdio write access to use MII_GMAC4_WRITE only instead of
OR together with MII_WRITE.
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Acked-By: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
