Add the possibility to route a mix of the two channels of stereo data to
the center and LFE outputs. Due to a WM8766 restriction, all surround
and back channels also get the mixed L/R signal in this case.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Automatically mute the speaker outputs as long as a headphone is plugged.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now that the polarity of the headphone detection pin is known, replace
the debugging message with a proper jack plug input device.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the correct number, register bits, and names for the input switches.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The check for the volume update latch bit was accidentally in the wrong
function, where it would prevent the MSB from being written, instead of
correctly ignoring it for cached values.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If we are busy, then we may have woken up the wait_request handler but
not yet serviced it before the hang check fires. So in hang check,
double check that the i915_gem_do_wait_request() is still pending the
wake-up before declaring all hope lost.
Fixes regression with e78d73b16b.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30073
Reported-and-tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The copy of /proc/vmcore to a user buffer proceeds much faster
if the kernel addresses memory as cached.
With this patch we have seen an increase in transfer rate from
less than 15MB/s to 80-460MB/s, depending on size of the
transfer. This makes a big difference in time needed to save a
system dump.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: kexec@lists.infradead.org
Cc: <stable@kernel.org> # as far back as it would apply
LKML-Reference: <E1OtMLz-0001yp-Ia@eag09.americas.sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
By adding the subwoofer as a speaker pin, it is treated correctly when auto-muting.
BugLink: https://launchpad.net/bugs/611803
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If we pass in a device which is higher than SNDRV_RAWMIDI_DEVICES then
the "next device" should be -1. This function just returns device + 1.
But the main thing is that "device + 1" can lead to a (harmless) integer
overflow and that annoys static analysis tools.
[fix the case for device == SNDRV_RAWMIDI_DEVICE by tiwai]
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It would be nice if people tested their patches before sending
them to me...
Cc: Henry Ptasinski <henryp@broadcom.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Nohee Ko <noheek@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The PL022 SPI bus is sometimes used for early stuff like
regulators that need to be present at module_init() time, so
we move this to a subsys_initcall().
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Use netdev_alloc_skb_ip_align() helper and do correct allocation
Tested-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 30fff923 introduced in linux-2.6.33 (udp: bind() optimisation)
added a secondary hash on UDP, hashed on (local addr, local port).
Problem is that following sequence :
fd = socket(...)
connect(fd, &remote, ...)
not only selects remote end point (address and port), but also sets
local address, while UDP stack stored in secondary hash table the socket
while its local address was INADDR_ANY (or ipv6 equivalent)
Sequence is :
- autobind() : choose a random local port, insert socket in hash tables
[while local address is INADDR_ANY]
- connect() : set remote address and port, change local address to IP
given by a route lookup.
When an incoming UDP frame comes, if more than 10 sockets are found in
primary hash table, we switch to secondary table, and fail to find
socket because its local address changed.
One solution to this problem is to rehash datagram socket if needed.
We add a new rehash(struct socket *) method in "struct proto", and
implement this method for UDP v4 & v6, using a common helper.
This rehashing only takes care of secondary hash table, since primary
hash (based on local port only) is not changed.
Reported-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Chris Snook <chris.snook@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use cmpxchg() to get rid of spinlocks in inet_add_protocol() and
friends.
inet_protos[] & inet6_protos[] are moved to read_mostly section
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a patch to the adl_pci9111.c file that fixes up multiple please,
no space for starting a line warnings, found by the checkpatch.pl tool
Signed-off-by: Maurice Dawson <mauricedawson2699@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ignore ADSL routers, which can have the same vendor and product IDs
as ADSL modems but should be handled by the cx82310_eth driver.
This intentionally ignores device IDs that aren't currently handled
by cx82310_eth. There may be other device IDs that perhaps shouldn't
be claimed by cxacru.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving the AR6002 hw 2.0 specific register definitions files from
the hw.0 directory to a new directory, 'hw' within hw2.0.
Signed-off-by: Vipin Mehta <vmehta@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Sprint 4G network uses a Wimax dongle with Beecem
chipset. The driver is typical of out of tree drivers, but
maybe useful for people, and the hardware is readily available.
Here is a staging ready version (i.e warts and all)
0. Started with Rel_5.2.7.3P1_USB from Sprint4GDeveloperPack-1.1
1. Consolidated files in staging
2. Remove Dos cr/lf
3. Remove unnecessary ioctl from usbbcm_fops
Applied patches that were in the developer pack, surprising
there were ones for 2.6.35 already.
This is compile tested only, see TODO for what still needs
to be done.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace e.g. u_int32_t types with the more common uint32_t.
Reported-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Also, a number of changes were made based on the assumption that
rds.h wasn't exported, so roll these back.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Add two CMSGs for masked versions of cswp and fadd. args
struct modified to use a union for different atomic op type's
arguments. Change IB to do masked atomic ops. Atomic op type
in rds_message similarly unionized.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
This prints the constant identifier for work completion status and rdma
cm event types, like we already do for IB event types.
A core string array helper is added that each string type uses.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
Nothing was canceling the send and receive work that might have been
queued as a conn was being destroyed.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
rds_conn_shutdown() can return before the connection is shut down when
it encounters an existing state that it doesn't understand. This lets
rds_conn_destroy() then start tearing down the conn from under paths
that are still using it.
It's more reliable the shutdown work and wait for krdsd to complete the
shutdown callback. This stopped some hangs I was seeing where krdsd was
trying to shut down a freed conn.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
Right now there's nothing to stop the various paths that use
rs->rs_transport from racing with rmmod and executing freed transport
code. The simple fix is to have binding to a transport also hold a
reference to the transport's module, removing this class of races.
We already had an unused t_owner field which was set for the modular
transports and which wasn't set for the built-in loop transport.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
rs_transport is now also used by the rdma paths once the socket is
bound. We don't need this stale comment to tell us what cscope can.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
rds_conn_destroy() can race with all other modifications of the
rds_conn_count but it was modifying the count without locking.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
The RDS IB device list wasn't protected by any locking. Traversal in
both the get_mr and FMR flushing paths could race with additon and
removal.
List manipulation is done with RCU primatives and is protected by the
write side of a rwsem. The list traversal in the get_mr fast path is
protected by a rcu read critical section. The FMR list traversal is
more problematic because it can block while traversing the list. We
protect this with the read side of the rwsem.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
It's nice to not have to go digging in the code to see which event
occurred. It's easy to throw together a quick array that maps the ib
event enums to their strings. I didn't see anything in the stack that
does this translation for us, but I also didn't look very hard.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
Flushing FMRs is somewhat expensive, and is currently kicked off when
the interrupt handler notices that we are getting low. The result of
this is that FMR flushing only happens from the interrupt cpus.
This spreads the load more effectively by triggering flushes just before
we allocate a new FMR.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
We're seeing bugs today where IB connection shutdown clears the send
ring while the tasklet is processing completed sends. Implementation
details cause this to dereference a null pointer. Shutdown needs to
wait for send completion to stop before tearing down the connection. We
can't simply wait for the ring to empty because it may contain
unsignaled sends that will never be processed.
This patch tracks the number of signaled sends that we've posted and
waits for them to complete. It also makes sure that the tasklet has
finished executing.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
We are *definitely* counting cycles as closely as DaveM, so
ensure hwcache alignment for our recv ring control structs.
Signed-off-by: Andy Grover <andy.grover@oracle.com>