commit 0d9cfc9b8c upstream.
The Gemalto Cinterion PLS83-W modem (cdc_ether) is emitting confusing link
up and down events when the WWAN interface is activated on the modem-side.
Interrupt URBs will in consecutive polls grab:
* Link Connected
* Link Disconnected
* Link Connected
Where the last Connected is then a stable link state.
When the system is under load this may cause the unlink_urbs() work in
__handle_link_change() to not complete before the next usbnet_link_change()
call turns the carrier on again, allowing rx_submit() to queue new SKBs.
In that event the URB queue is filled faster than it can drain, ending up
in a RCU stall:
rcu: INFO: rcu_sched detected expedited stalls on CPUs/tasks: { 0-.... } 33108 jiffies s: 201 root: 0x1/.
rcu: blocking rcu_node structures (internal RCU debug):
Sending NMI from CPU 1 to CPUs 0:
NMI backtrace for cpu 0
Call trace:
arch_local_irq_enable+0x4/0x8
local_bh_enable+0x18/0x20
__netdev_alloc_skb+0x18c/0x1cc
rx_submit+0x68/0x1f8 [usbnet]
rx_alloc_submit+0x4c/0x74 [usbnet]
usbnet_bh+0x1d8/0x218 [usbnet]
usbnet_bh_tasklet+0x10/0x18 [usbnet]
tasklet_action_common+0xa8/0x110
tasklet_action+0x2c/0x34
handle_softirqs+0x2cc/0x3a0
__do_softirq+0x10/0x18
____do_softirq+0xc/0x14
call_on_irq_stack+0x24/0x34
do_softirq_own_stack+0x18/0x20
__irq_exit_rcu+0xa8/0xb8
irq_exit_rcu+0xc/0x30
el1_interrupt+0x34/0x48
el1h_64_irq_handler+0x14/0x1c
el1h_64_irq+0x68/0x6c
_raw_spin_unlock_irqrestore+0x38/0x48
xhci_urb_dequeue+0x1ac/0x45c [xhci_hcd]
unlink1+0xd4/0xdc [usbcore]
usb_hcd_unlink_urb+0x70/0xb0 [usbcore]
usb_unlink_urb+0x24/0x44 [usbcore]
unlink_urbs.constprop.0.isra.0+0x64/0xa8 [usbnet]
__handle_link_change+0x34/0x70 [usbnet]
usbnet_deferred_kevent+0x1c0/0x320 [usbnet]
process_scheduled_works+0x2d0/0x48c
worker_thread+0x150/0x1dc
kthread+0xd8/0xe8
ret_from_fork+0x10/0x20
Get around the problem by delaying the carrier on to the scheduled work.
This needs a new flag to keep track of the necessary action.
The carrier ok check cannot be removed as it remains required for the
LINK_RESET event flow.
Fixes: 4b49f58fff ("usbnet: handle link change")
Cc: stable@vger.kernel.org
Signed-off-by: John Ernberg <john.ernberg@actia.se>
Link: https://patch.msgid.link/20250723102526.1305339-1-john.ernberg@actia.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bdc877ba6b ]
The moduleparam code allows modules to provide their own definition of
MODULE_PARAM_PREFIX, instead of using the default KBUILD_MODNAME ".".
Commit 730b69d225 ("module: check kernel param length at compile time,
not runtime") added a check to ensure the prefix doesn't exceed
MODULE_NAME_LEN, as this is what param_sysfs_builtin() expects.
Later, commit 58f86cc89c ("VERIFY_OCTAL_PERMISSIONS: stricter checking
for sysfs perms.") removed this check, but there is no indication this was
intentional.
Since the check is still useful for param_sysfs_builtin() to function
properly, reintroduce it in __module_param_call(), but in a modernized form
using static_assert().
While here, clean up the __module_param_call() comments. In particular,
remove the comment "Default value instead of permissions?", which comes
from commit 9774a1f54f ("[PATCH] Compile-time check re world-writeable
module params"). This comment was related to the test variable
__param_perm_check_##name, which was removed in the previously mentioned
commit 58f86cc89c.
Fixes: 58f86cc89c ("VERIFY_OCTAL_PERMISSIONS: stricter checking for sysfs perms.")
Signed-off-by: Petr Pavlu <petr.pavlu@suse.com>
Reviewed-by: Daniel Gomez <da.gomez@samsung.com>
Link: https://lore.kernel.org/r/20250630143535.267745-4-petr.pavlu@suse.com
Signed-off-by: Daniel Gomez <da.gomez@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 12c409aa1e ]
Because pps_cdev_poll() returns unconditionally EPOLLIN,
a user space program that calls select/poll get always an immediate data
ready-to-read response. As a result the intended use to wait until next
data becomes ready does not work.
User space snippet:
struct pollfd pollfd = {
.fd = open("/dev/pps0", O_RDONLY),
.events = POLLIN|POLLERR,
.revents = 0 };
while(1) {
poll(&pollfd, 1, 2000/*ms*/); // returns immediate, but should wait
if(revents & EPOLLIN) { // always true
struct pps_fdata fdata;
memset(&fdata, 0, sizeof(memdata));
ioctl(PPS_FETCH, &fdata); // currently fetches data at max speed
}
}
Lets remember the last fetch event counter and compare this value
in pps_cdev_poll() with most recent event counter
and return 0 if they are equal.
Signed-off-by: Denis OSTERLAND-HEIM <denis.osterland@diehl.com>
Co-developed-by: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Rodolfo Giometti <giometti@enneenne.com>
Fixes: eae9d2ba0c ("LinuxPPS: core support")
Link: https://lore.kernel.org/all/f6bed779-6d59-4f0f-8a59-b6312bd83b4e@enneenne.com/
Acked-by: Rodolfo Giometti <giometti@enneenne.com>
Link: https://lore.kernel.org/r/c3c50ad1eb19ef553eca8a57c17f4c006413ab70.camel@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ffaf1bf373 ]
The macro takes a parameter called "p" but references "fc" internally.
This happens to compile as long as callers pass a variable named fc,
but breaks otherwise. Rename the first parameter to “fc” to match the
usage and to be consistent with warnfc() / errorfc().
Fixes: a3ff937b33 ("prefix-handling analogues of errorf() and friends")
Signed-off-by: RubenKelevra <rubenkelevra@gmail.com>
Link: https://lore.kernel.org/20250617230927.1790401-1-rubenkelevra@gmail.com
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 42a20f86dc upstream.
Having a stable wchan means the process must be blocked and for it to
stay that way while performing stack unwinding.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> [arm]
Tested-by: Mark Rutland <mark.rutland@arm.com> [arm64]
Link: https://lkml.kernel.org/r/20211008111626.332092234@infradead.org
Signed-off-by: Siddhi Katage <siddhi.katage@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d7b896acbd ]
This commit adds the needed definitions for using the klm_umr_wqe.
UMR stands for user-mode memory registration, is a mechanism to alter
address translation properties of MKEY by posting WorkQueueElement
aka WQE on send queue.
MKEY stands for memory key, MKEY are used to describe a region in memory that
can be later used by HW.
KLM stands for {Key, Length, MemVa}, KLM_MKEY is indirect MKEY that enables
to map multiple memory spaces with different sizes in unified MKEY.
klm_umr_wqe is a UMR that use to update a KLM_MKEY.
SHAMPO feature uses KLM_MKEY for memory registration of his header buffer.
Signed-off-by: Ben Ben-Ishay <benishay@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Stable-dep-of: 531d0d32de ("net/mlx5: Correctly set gso_size when LRO is used")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c921ff373b ]
Abstract the complexity of iterating over all the fences
in a dma_resv object.
The new loop handles the whole RCU and retry dance and
returns only fences where we can be sure we grabbed the
right one.
v2: fix accessing the shared fences while they might be freed,
improve kerneldoc, rename _cursor to _iter, add
dma_resv_iter_is_exclusive, add dma_resv_iter_begin/end
v3: restructor the code, move rcu_read_lock()/unlock() into the
iterator, add dma_resv_iter_is_restarted()
v4: fix NULL deref when no explicit fence exists, drop superflous
rcu_read_lock()/unlock() calls.
v5: fix typos in the documentation
v6: fix coding error when excl fence is NULL
v7: one more logic fix
v8: fix index check in dma_resv_iter_is_exclusive()
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> (v7)
Link: https://patchwork.freedesktop.org/patch/msgid/20211005113742.1101-2-christian.koenig@amd.com
Stable-dep-of: 2b95a7db6e ("dma-buf: fix timeout handling in dma_resv_wait_timeout v2")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d8010d4ba4 upstream.
Add the required features detection glue to bugs.c et all in order to
support the TSA mitigation.
Co-developed-by: Kim Phillips <kim.phillips@amd.com>
Signed-off-by: Kim Phillips <kim.phillips@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit adfdfcbdbd ]
This is simillar as fixed-regulator.
Used to extract regulator parent from the device tree.
Without that property used, the parent regulator can be shut down (if not an always on).
Thus leading to inappropriate behavior:
On am62-SP-SK this fix is required to avoid tps65219 ldo1 (SDMMC rail) to be shut down after boot completion.
Signed-off-by: Jerome Neanne <jneanne@baylibre.com>
Link: https://lore.kernel.org/r/20220929132526.29427-2-jneanne@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: c9764fd88b ("regulator: gpio: Fix the out-of-bounds access to drvdata::gpiods")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit af4db5a35a upstream.
A poorly implemented DisplayPort Alt Mode port partner can indicate
that its pin assignment capabilities are greater than the maximum
value, DP_PIN_ASSIGN_F. In this case, calls to pin_assignment_show
will cause a BRK exception due to an out of bounds array access.
Prevent for loop in pin_assignment_show from accessing
invalid values in pin_assignments by adding DP_PIN_ASSIGN_MAX
value in typec_dp.h and using i < DP_PIN_ASSIGN_MAX as a loop
condition.
Fixes: 0e3bb7d689 ("usb: typec: Add driver for DisplayPort alternate mode")
Cc: stable <stable@kernel.org>
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250618224943.3263103-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 2b572c4098 which is
commit a18dfa9925 upstream.
A regression was introduced when backporting this to the stable kernels
without applying previous commits in this series.
When sending IPv6 UDP packets larger than MTU, EMSGSIZE was returned
instead of fragmenting the packets as expected.
As there is no compelling reason for this commit to be present in the
stable kernels it should be reverted.
Signed-off-by: Brett A C Sheffield <bacs@librecast.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8d5cc8eed7 ]
The non-zero (true) return value from consw::con_switch() means a redraw
is needed. So make this return type a bool explicitly instead of int.
The latter might imply that -Eerrors are expected. They are not.
And document the hook.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: linux-fbdev@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-parisc@vger.kernel.org
Tested-by: Helge Deller <deller@gmx.de> # parisc STI console
Link: https://lore.kernel.org/r/20240122110401.7289-31-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 03bcbbb399 ("dummycon: Trigger redraw when switching consoles with deferred takeover")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 559f01a0ee ]
In consw::con_clear():
* Height is always 1, so drop it.
* Offsets and width are always unsigned values, so re-type them as such.
This needs a new __fbcon_clear() in the fbcon code to still handle
height which might not be 1 when called internally.
Note that tests for negative count/width are left in place -- they are
taken care of in the next patches.
And document the hook.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: linux-fbdev@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-parisc@vger.kernel.org
Tested-by: Helge Deller <deller@gmx.de> # parisc STI console
Link: https://lore.kernel.org/r/20240122110401.7289-22-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 03bcbbb399 ("dummycon: Trigger redraw when switching consoles with deferred takeover")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dae3e6b618 ]
The 'init' parameter of consw::con_init() is true for the first call of
the hook on a particular console. So make the parameter a bool.
And document the hook.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: linux-fbdev@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-parisc@vger.kernel.org
Tested-by: Helge Deller <deller@gmx.de> # parisc STI console
Link: https://lore.kernel.org/r/20240122110401.7289-21-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 03bcbbb399 ("dummycon: Trigger redraw when switching consoles with deferred takeover")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4173f018aa ]
struct uni_pagedir contains 32 unicode page directories, so the name of
the structure is a bit misleading. Rename the structure to uni_pagedict,
so it looks like this:
struct uni_pagedict
-> 32 page dirs
-> 32 rows
-> 64 glyphs
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 03bcbbb399 ("dummycon: Trigger redraw when switching consoles with deferred takeover")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8c4bd6c6e ]
Add a function to query for the preferred ring buffer size of VMBus
device. This will allow the drivers (eg. UIO) to allocate the most
optimized ring buffer size for devices.
Signed-off-by: Saurabh Sengar <ssengar@linux.microsoft.com>
Reviewed-by: Long Li <longli@microsoft.com>
Link: https://lore.kernel.org/r/1711788723-8593-2-git-send-email-ssengar@linux.microsoft.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 0315fef2af ("uio_hv_generic: Align ring size to system page")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 59d9094df3 upstream.
The folio refcount may be increased unexpectly through try_get_folio() by
caller such as split_huge_pages. In huge_pmd_unshare(), we use refcount
to check whether a pmd page table is shared. The check is incorrect if
the refcount is increased by the above caller, and this can cause the page
table leaked:
BUG: Bad page state in process sh pfn:109324
page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x66 pfn:0x109324
flags: 0x17ffff800000000(node=0|zone=2|lastcpupid=0xfffff)
page_type: f2(table)
raw: 017ffff800000000 0000000000000000 0000000000000000 0000000000000000
raw: 0000000000000066 0000000000000000 00000000f2000000 0000000000000000
page dumped because: nonzero mapcount
...
CPU: 31 UID: 0 PID: 7515 Comm: sh Kdump: loaded Tainted: G B 6.13.0-rc2master+ #7
Tainted: [B]=BAD_PAGE
Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
Call trace:
show_stack+0x20/0x38 (C)
dump_stack_lvl+0x80/0xf8
dump_stack+0x18/0x28
bad_page+0x8c/0x130
free_page_is_bad_report+0xa4/0xb0
free_unref_page+0x3cc/0x620
__folio_put+0xf4/0x158
split_huge_pages_all+0x1e0/0x3e8
split_huge_pages_write+0x25c/0x2d8
full_proxy_write+0x64/0xd8
vfs_write+0xcc/0x280
ksys_write+0x70/0x110
__arm64_sys_write+0x24/0x38
invoke_syscall+0x50/0x120
el0_svc_common.constprop.0+0xc8/0xf0
do_el0_svc+0x24/0x38
el0_svc+0x34/0x128
el0t_64_sync_handler+0xc8/0xd0
el0t_64_sync+0x190/0x198
The issue may be triggered by damon, offline_page, page_idle, etc, which
will increase the refcount of page table.
1. The page table itself will be discarded after reporting the
"nonzero mapcount".
2. The HugeTLB page mapped by the page table miss freeing since we
treat the page table as shared and a shared page table will not be
unmapped.
Fix it by introducing independent PMD page table shared count. As
described by comment, pt_index/pt_mm/pt_frag_refcount are used for s390
gmap, x86 pgds and powerpc, pt_share_count is used for x86/arm64/riscv
pmds, so we can reuse the field as pt_share_count.
Link: https://lkml.kernel.org/r/20241216071147.3984217-1-liushixin2@huawei.com
Fixes: 39dde65c99 ("[PATCH] shared page table for hugetlb page")
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Ken Chen <kenneth.w.chen@intel.com>
Cc: Muchun Song <muchun.song@linux.dev>
Cc: Nanyong Sun <sunnanyong@huawei.com>
Cc: Jane Chu <jane.chu@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[backport note: struct ptdesc did not exist yet, stuff it equivalently
into struct page instead]
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 081056dc00 upstream.
Currently, __split_vma() triggers hugetlb page table unsharing through
vm_ops->may_split(). This happens before the VMA lock and rmap locks are
taken - which is too early, it allows racing VMA-locked page faults in our
process and racing rmap walks from other processes to cause page tables to
be shared again before we actually perform the split.
Fix it by explicitly calling into the hugetlb unshare logic from
__split_vma() in the same place where THP splitting also happens. At that
point, both the VMA and the rmap(s) are write-locked.
An annoying detail is that we can now call into the helper
hugetlb_unshare_pmds() from two different locking contexts:
1. from hugetlb_split(), holding:
- mmap lock (exclusively)
- VMA lock
- file rmap lock (exclusively)
2. hugetlb_unshare_all_pmds(), which I think is designed to be able to
call us with only the mmap lock held (in shared mode), but currently
only runs while holding mmap lock (exclusively) and VMA lock
Backporting note:
This commit fixes a racy protection that was introduced in commit
b30c14cd61 ("hugetlb: unshare some PMDs when splitting VMAs"); that
commit claimed to fix an issue introduced in 5.13, but it should actually
also go all the way back.
[jannh@google.com: v2]
Link: https://lkml.kernel.org/r/20250528-hugetlb-fixes-splitrace-v2-1-1329349bad1a@google.com
Link: https://lkml.kernel.org/r/20250528-hugetlb-fixes-splitrace-v2-0-1329349bad1a@google.com
Link: https://lkml.kernel.org/r/20250527-hugetlb-fixes-splitrace-v1-1-f4136f5ec58a@google.com
Fixes: 39dde65c99 ("[PATCH] shared page table for hugetlb page")
Signed-off-by: Jann Horn <jannh@google.com>
Cc: Liam Howlett <liam.howlett@oracle.com>
Reviewed-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org> [b30c14cd61: hugetlb: unshare some PMDs when splitting VMAs]
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[stable backport: code got moved around, VMA splitting is in
__vma_adjust, hugetlb lock wasn't used back then]
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe7f7ac8e0 upstream.
Update struct hid_descriptor to better reflect the mandatory and
optional parts of the HID Descriptor as per USB HID 1.11 specification.
Note: the kernel currently does not parse any optional HID class
descriptors, only the mandatory report descriptor.
Update all references to member element desc[0] to rpt_desc.
Add test to verify bLength and bNumDescriptors values are valid.
Replace the for loop with direct access to the mandatory HID class
descriptor member for the report descriptor. This eliminates the
possibility of getting an out-of-bounds fault.
Add a warning message if the HID descriptor contains any unsupported
optional HID class descriptors.
Reported-by: syzbot+c52569baf0c843f35495@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=c52569baf0c843f35495
Fixes: f043bfc98c ("HID: usbhid: fix out-of-bounds bug")
Cc: stable@vger.kernel.org
Signed-off-by: Terry Junge <linuxhid@cosmicgizmosystems.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Terry Junge <linuxhid@cosmicgizmosystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7851263998 upstream.
In vcc_sendmsg(), we account skb->truesize to sk->sk_wmem_alloc by
atm_account_tx().
It is expected to be reverted by atm_pop_raw() later called by
vcc->dev->ops->send(vcc, skb).
However, vcc_sendmsg() misses the same revert when copy_from_iter_full()
fails, and then we will leak a socket.
Let's factorise the revert part as atm_return_tx() and call it in
the failure path.
Note that the corresponding sk_wmem_alloc operation can be found in
alloc_tx() as of the blamed commit.
$ git blame -L:alloc_tx net/atm/common.c c55fa3cccb~
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Simon Horman <horms@kernel.org>
Closes: https://lore.kernel.org/netdev/20250614161959.GR414686@horms.kernel.org/
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250616182147.963333-3-kuni1840@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 59529bbe64 ]
SDEI usually initialize with the ACPI table, but on platforms where
ACPI is not used, the SDEI feature can still be used to handle
specific firmware calls or other customized purposes. Therefore, it
is not necessary for ARM_SDE_INTERFACE to depend on ACPI_APEI_GHES.
In commit dc4e8c07e9 ("ACPI: APEI: explicit init of HEST and GHES
in acpi_init()"), to make APEI ready earlier, sdei_init was moved
into acpi_ghes_init instead of being a standalone initcall, adding
ACPI_APEI_GHES dependency to ARM_SDE_INTERFACE. This restricts the
flexibility and usability of SDEI.
This patch corrects the dependency in Kconfig and splits sdei_init()
into two separate functions: sdei_init() and acpi_sdei_init().
sdei_init() will be called by arch_initcall and will only initialize
the platform driver, while acpi_sdei_init() will initialize the
device from acpi_ghes_init() when ACPI is ready. This allows the
initialization of SDEI without ACPI_APEI_GHES enabled.
Fixes: dc4e8c07e9 ("ACPI: APEI: explicit init of HEST and GHES in apci_init()")
Cc: Shuai Xue <xueshuai@linux.alibaba.com>
Signed-off-by: Huang Yiwei <quic_hyiwei@quicinc.com>
Reviewed-by: Shuai Xue <xueshuai@linux.alibaba.com>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20250507045757.2658795-1-quic_hyiwei@quicinc.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f661f71fd ]
With some Infineon chips the timeouts in tpm_tis_send_data (both B and
C) can reach up to about 2250 ms.
Timeout C is retried since
commit de9e33df77 ("tpm, tpm_tis: Workaround failed command reception on Infineon devices")
Timeout B still needs to be extended.
The problem is most commonly encountered with context related operation
such as load context/save context. These are issued directly by the
kernel, and there is no retry logic for them.
When a filesystem is set up to use the TPM for unlocking the boot fails,
and restarting the userspace service is ineffective. This is likely
because ignoring a load context/save context result puts the real TPM
state and the TPM state expected by the kernel out of sync.
Chips known to be affected:
tpm_tis IFX1522:00: 2.0 TPM (device-id 0x1D, rev-id 54)
Description: SLB9672
Firmware Revision: 15.22
tpm_tis MSFT0101:00: 2.0 TPM (device-id 0x1B, rev-id 22)
Firmware Revision: 7.83
tpm_tis MSFT0101:00: 2.0 TPM (device-id 0x1A, rev-id 16)
Firmware Revision: 5.63
Link: https://lore.kernel.org/linux-integrity/Z5pI07m0Muapyu9w@kitsune.suse.cz/
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b5325b2a27 upstream.
Give userspace a way to instruct the kernel to install a pidfd into the
usermode helper process. This makes coredump handling a lot more
reliable for userspace. In parallel with this commit we already have
systemd adding support for this in [1].
We create a pidfs file for the coredumping process when we process the
corename pattern. When the usermode helper process is forked we then
install the pidfs file as file descriptor three into the usermode
helpers file descriptor table so it's available to the exec'd program.
Since usermode helpers are either children of the system_unbound_wq
workqueue or kthreadd we know that the file descriptor table is empty
and can thus always use three as the file descriptor number.
Note, that we'll install a pidfd for the thread-group leader even if a
subthread is calling do_coredump(). We know that task linkage hasn't
been removed due to delay_group_leader() and even if this @current isn't
the actual thread-group leader we know that the thread-group leader
cannot be reaped until @current has exited.
[brauner: This is a backport for the v5.14 series. Upstream has
significantly changed and backporting all that infra is a non-starter.
So simply backport the pidfd_prepare() helper and waste the file
descriptor we allocated. Then we minimally massage the umh coredump
setup code.]
Link: https://github.com/systemd/systemd/pull/37125 [1]
Link: https://lore.kernel.org/20250414-work-coredump-v2-3-685bf231f828@kernel.org
Tested-by: Luca Boccassi <luca.boccassi@gmail.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ae930d9db upstream.
Add a new helper that allows to reserve a pidfd and allocates a new
pidfd file that stashes the provided struct pid. This will allow us to
remove places that either open code this function or that call
pidfd_create() but then have to call close_fd() because there are still
failure points after pidfd_create() has been called.
Reviewed-by: Jan Kara <jack@suse.cz>
Message-Id: <20230327-pidfd-file-api-v1-1-5c0e9a3158e4@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ad6b5b73ff ]
rcu_all_qs() is defined for !CONFIG_PREEMPT_RCU but the declaration
is conditioned on CONFIG_PREEMPTION.
With CONFIG_PREEMPT_LAZY, CONFIG_PREEMPTION=y does not imply
CONFIG_PREEMPT_RCU=y.
Decouple the two.
Cc: Paul E. McKenney <paulmck@kernel.org>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Ankur Arora <ankur.a.arora@oracle.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 848b09d53d ]
The Dell AW1022z is an RTL8156B based 2.5G Ethernet controller.
Add the vendor and product ID values to the driver. This makes Ethernet
work with the adapter.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://patch.msgid.link/20250206224033.980115-1-olek2@wp.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a6f18f286 ]
GCC can see that the value range for "order" is capped, but this leads
it to consider that it might be negative, leading to a false positive
warning (with GCC 15 with -Warray-bounds -fdiagnostics-details):
../drivers/net/ethernet/mellanox/mlx4/alloc.c:691:47: error: array subscript -1 is below array bounds of 'long unsigned int *[2]' [-Werror=array-bounds=]
691 | i = find_first_bit(pgdir->bits[o], MLX4_DB_PER_PAGE >> o);
| ~~~~~~~~~~~^~~
'mlx4_alloc_db_from_pgdir': events 1-2
691 | i = find_first_bit(pgdir->bits[o], MLX4_DB_PER_PAGE >> o); | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
| | | | | (2) out of array bounds here
| (1) when the condition is evaluated to true In file included from ../drivers/net/ethernet/mellanox/mlx4/mlx4.h:53,
from ../drivers/net/ethernet/mellanox/mlx4/alloc.c:42:
../include/linux/mlx4/device.h:664:33: note: while referencing 'bits'
664 | unsigned long *bits[2];
| ^~~~
Switch the argument to unsigned int, which removes the compiler needing
to consider negative values.
Signed-off-by: Kees Cook <kees@kernel.org>
Link: https://patch.msgid.link/20250210174504.work.075-kees@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc47f07234 ]
Unlike the decompression code, the compression code in LZO never
checked for output overruns. It instead assumes that the caller
always provides enough buffer space, disregarding the buffer length
provided by the caller.
Add a safe compression interface that checks for the end of buffer
before each write. Use the safe interface in crypto/lzo.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a18dfa9925 ]
When spanning datagram construction over multiple send calls using
MSG_MORE, per datagram settings are configured on the first send.
That is when ip(6)_setup_cork stores these settings for subsequent use
in __ip(6)_append_data and others.
The only flag that escaped this was dontfrag. As a result, a datagram
could be constructed with df=0 on the first sendmsg, but df=1 on a
next. Which is what cmsg_ip.sh does in an upcoming MSG_MORE test in
the "diff" scenario.
Changing datagram conditions in the middle of constructing an skb
makes this already complex code path even more convoluted. It is here
unintentional. Bring this flag in line with expected sockopt/cmsg
behavior.
And stop passing ipc6 to __ip6_append_data, to avoid such issues
in the future. This is already the case for __ip_append_data.
inet6_cork had a 6 byte hole, so the 1B flag has no impact.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250307033620.411611-3-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 196a062641 ]
Binary printing functions are using printf() type of format, and compiler
is not happy about them as is:
kernel/trace/trace.c:3292:9: error: function ‘trace_vbprintk’ might be a candidate for ‘gnu_printf’ format attribute [-Werror=suggest-attribute=format]
kernel/trace/trace_seq.c:182:9: error: function ‘trace_seq_bprintf’ might be a candidate for ‘gnu_printf’ format attribute [-Werror=suggest-attribute=format]
Fix the compilation errors by adding __printf() attribute.
While at it, move existing __printf() attributes from the implementations
to the declarations. IT also fixes incorrect attribute parameters that are
used for trace_array_printk().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Kees Cook <kees@kernel.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20250321144822.324050-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9b19ea630 ]
When CONFIG_NEED_DMA_MAP_STATE is not defined, dma-mapping clients might
report unused data compilation warnings for dma_unmap_*() calls
arguments. Redefine macros for those calls to let compiler to notice that
it is okay when the provided arguments are not used.
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250415075659.428549-1-m.szyprowski@samsung.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 872df34d7c upstream.
ITS mitigation moves the unsafe indirect branches to a safe thunk. This
could degrade the prediction accuracy as the source address of indirect
branches becomes same for different execution paths.
To improve the predictions, and hence the performance, assign a separate
thunk for each indirect callsite. This is also a defense-in-depth measure
to avoid indirect branches aliasing with each other.
As an example, 5000 dynamic thunks would utilize around 16 bits of the
address space, thereby gaining entropy. For a BTB that uses
32 bits for indexing, dynamic thunks could provide better prediction
accuracy over fixed thunks.
Have ITS thunks be variable sized and use EXECMEM_MODULE_TEXT such that
they are both more flexible (got to extend them later) and live in 2M TLBs,
just like kernel code, avoiding undue TLB pressure.
[ pawan: CONFIG_EXECMEM and CONFIG_EXECMEM_ROX are not supported on
backport kernel, made changes to use module_alloc() and
set_memory_*() for dynamic thunks. ]
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Alexandre Chartre <alexandre.chartre@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4818881c4 upstream.
Indirect Target Selection (ITS) is a bug in some pre-ADL Intel CPUs with
eIBRS. It affects prediction of indirect branch and RETs in the
lower half of cacheline. Due to ITS such branches may get wrongly predicted
to a target of (direct or indirect) branch that is located in the upper
half of the cacheline.
Scope of impact
===============
Guest/host isolation
--------------------
When eIBRS is used for guest/host isolation, the indirect branches in the
VMM may still be predicted with targets corresponding to branches in the
guest.
Intra-mode
----------
cBPF or other native gadgets can be used for intra-mode training and
disclosure using ITS.
User/kernel isolation
---------------------
When eIBRS is enabled user/kernel isolation is not impacted.
Indirect Branch Prediction Barrier (IBPB)
-----------------------------------------
After an IBPB, indirect branches may be predicted with targets
corresponding to direct branches which were executed prior to IBPB. This is
mitigated by a microcode update.
Add cmdline parameter indirect_target_selection=off|on|force to control the
mitigation to relocate the affected branches to an ITS-safe thunk i.e.
located in the upper half of cacheline. Also add the sysfs reporting.
When retpoline mitigation is deployed, ITS safe-thunks are not needed,
because retpoline sequence is already ITS-safe. Similarly, when call depth
tracking (CDT) mitigation is deployed (retbleed=stuff), ITS safe return
thunk is not used, as CDT prevents RSB-underflow.
To not overcomplicate things, ITS mitigation is not supported with
spectre-v2 lfence;jmp mitigation. Moreover, it is less practical to deploy
lfence;jmp mitigation on ITS affected parts anyways.
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@kernel.org>
Reviewed-by: Alexandre Chartre <alexandre.chartre@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e4ca0e59c3 ]
Some user may want to use aligned signed 64-bit type.
Provide it for them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20240903180218.3640501-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stable-dep-of: 5097eaae98 ("iio: adc: dln2: Use aligned_s64 for timestamp")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 608723c41c ]
The kvfree_rcu() and kfree_rcu() APIs are hazardous in that if you forget
the second argument, it works, but might sleep. This sleeping can be a
correctness bug from atomic contexts, and even in non-atomic contexts
it might introduce unacceptable latencies. This commit therefore adds
kvfree_rcu_mightsleep() and kfree_rcu_mightsleep(), which will replace
the single-argument kvfree_rcu() and kfree_rcu(), respectively.
This commit enables a series of commits that switch from single-argument
kvfree_rcu() and kfree_rcu() to their _mightsleep() counterparts. Once
all of these commits land, the single-argument versions will be removed.
Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Stable-dep-of: 511e64e13d ("can: gw: fix RCU/BH usage in cgw_create_job()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Ricardo reported a KASAN discovered use after free in v6.6-stable.
The syzbot starts a BPF program via xdp_test_run_batch() which assigns
ri->tgt_value via dev_hash_map_redirect() and the return code isn't
XDP_REDIRECT it looks like nonsense. So the output in
bpf_warn_invalid_xdp_action() appears once.
Then the TUN driver runs another BPF program (on the same CPU) which
returns XDP_REDIRECT without setting ri->tgt_value first. It invokes
bpf_trace_printk() to print four characters and obtain the required
return value. This is enough to get xdp_do_redirect() invoked which
then accesses the pointer in tgt_value which might have been already
deallocated.
This problem does not affect upstream because since commit
401cb7dae8 ("net: Reference bpf_redirect_info via task_struct on PREEMPT_RT.")
the per-CPU variable is referenced via task's task_struct and exists on
the stack during NAPI callback. Therefore it is cleared once before the
first invocation and remains valid within the RCU section of the NAPI
callback.
Instead of performing the huge backport of the commit (plus its fix ups)
here is an alternative version which only resets the variable in
question prior invoking the BPF program.
Acked-by: Toke Høiland-Jørgensen <toke@kernel.org>
Reported-by: Ricardo Cañuelo Navarro <rcn@igalia.com>
Closes: https://lore.kernel.org/all/20250226-20250204-kasan-slab-use-after-free-read-in-dev_map_enqueue__submit-v3-0-360efec441ba@igalia.com/
Fixes: 97f91a7cf0 ("bpf: add bpf_redirect_map helper routine")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c14f7ccc9f ]
Replace assignment of PCI domain IDs from atomic_inc_return() to
ida_alloc().
Use two IDAs, one for static domain allocations (those which are defined in
device tree) and second for dynamic allocations (all other).
During removal of root bus / host bridge, also release the domain ID. The
released ID can be reused again, for example when dynamically loading and
unloading native PCI host bridge drivers.
This change also allows to mix static device tree assignment and dynamic by
kernel as all static allocations are reserved in dynamic pool.
[bhelgaas: set "err" if "bus->domain_nr < 0"]
Link: https://lore.kernel.org/r/20220714184130.5436-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Stable-dep-of: 804443c1f2 ("PCI: Fix reference leak in pci_register_host_bridge()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c072c4ef7e ]
Old Exynos SoCs have both Product ID and Revision ID in one single
register, while new SoCs tend to have two separate registers for those
IDs. Implement handling of both cases by passing Revision ID register
offsets in driver data.
Previously existing macros for Exynos4210 (removed in this patch) were
incorrect:
#define EXYNOS_SUBREV_MASK (0xf << 4)
#define EXYNOS_MAINREV_MASK (0xf << 0)
Actual format of PRO_ID register in Exynos4210 (offset 0x0):
[31:12] Product ID
[9:8] Package information
[7:4] Main Revision Number
[3:0] Sub Revision Number
This patch doesn't change the behavior on existing platforms, so
'/sys/devices/soc0/revision' will show the same string as before.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Tested-by: Henrik Grimler <henrik@grimler.se>
Link: https://lore.kernel.org/r/20211014133508.1210-1-semen.protsenko@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Stable-dep-of: c8222ef6cf ("soc: samsung: exynos-chipid: Add NULL pointer check in exynos_chipid_probe()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit dfd6200a09 upstream.
A new field 'online' is added to blkg_policy_data to fix following
2 problem:
1) In blkcg_activate_policy(), if pd_alloc_fn() with 'GFP_NOWAIT'
failed, 'queue_lock' will be dropped and pd_alloc_fn() will try again
without 'GFP_NOWAIT'. In the meantime, remove cgroup can race with
it, and pd_offline_fn() will be called without pd_init_fn() and
pd_online_fn(). This way null-ptr-deference can be triggered.
2) In order to synchronize pd_free_fn() from blkg_free_workfn() and
blkcg_deactivate_policy(), 'list_del_init(&blkg->q_node)' will be
delayed to blkg_free_workfn(), hence pd_offline_fn() can be called
first in blkg_destroy(), and then blkcg_deactivate_policy() will
call it again, we must prevent it.
The new field 'online' will be set after pd_online_fn() and will be
cleared after pd_offline_fn(), in the meantime pd_offline_fn() will only
be called if 'online' is set.
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230119110350.2287325-3-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Bin Lan <bin.lan.cn@windriver.com>
Signed-off-by: He Zhe <zhe.he@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cd35b6cb46 ]
nfs.ko, nfsd.ko, and lockd.ko all use crc32_le(), which is available
only when CONFIG_CRC32 is enabled. But the only NFS kconfig option that
selected CONFIG_CRC32 was CONFIG_NFS_DEBUG, which is client-specific and
did not actually guard the use of crc32_le() even on the client.
The code worked around this bug by only actually calling crc32_le() when
CONFIG_CRC32 is built-in, instead hard-coding '0' in other cases. This
avoided randconfig build errors, and in real kernels the fallback code
was unlikely to be reached since CONFIG_CRC32 is 'default y'. But, this
really needs to just be done properly, especially now that I'm planning
to update CONFIG_CRC32 to not be 'default y'.
Therefore, make CONFIG_NFS_FS, CONFIG_NFSD, and CONFIG_LOCKD select
CONFIG_CRC32. Then remove the fallback code that becomes unnecessary,
as well as the selection of CONFIG_CRC32 from CONFIG_NFS_DEBUG.
Fixes: 1264a2f053 ("NFS: refactor code for calculating the crc32 hash of a filehandle")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Anna Schumaker <anna.schumaker@oracle.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e59fb6749e ]
lockd needs to be able to hash filehandles for tracepoints. Move the
nfs_fhandle_hash() helper to a common nfs include file.
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Stable-dep-of: cd35b6cb46 ("nfs: add missing selections of CONFIG_CRC32")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9e888998ea upstream.
inode_to_wb() is used also for filesystems that don't support cgroup
writeback. For these filesystems inode->i_wb is stable during the
lifetime of the inode (it points to bdi->wb) and there's no need to hold
locks protecting the inode->i_wb dereference. Improve the warning in
inode_to_wb() to not trigger for these filesystems.
Link: https://lkml.kernel.org/r/20250412163914.3773459-3-agruenba@redhat.com
Fixes: aaa2cacf81 ("writeback: add lockdep annotation to inode_to_wb()")
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Reviewed-by: Andreas Gruenbacher <agruenba@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 09f37f2d7b ]
sched_smt_active() can be called from noinstr code, so it should always
be inlined. The CONFIG_SCHED_SMT version already has __always_inline.
Do the same for its !CONFIG_SCHED_SMT counterpart.
Fixes the following warning:
vmlinux.o: error: objtool: intel_idle_ibrs+0x13: call to sched_smt_active() leaves .noinstr.text section
Fixes: 321a874a7e ("sched/smt: Expose sched_smt_present static key")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/1d03907b0a247cf7fb5c1d518de378864f603060.1743481539.git.jpoimboe@kernel.org
Closes: https://lore.kernel.org/r/202503311434.lyw2Tveh-lkp@intel.com/
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb50844d72 ]
Currently, the following two macros have different values:
// The maximal argument count for firmware node reference
#define NR_FWNODE_REFERENCE_ARGS 8
// The maximal argument count for DT node reference
#define MAX_PHANDLE_ARGS 16
It may cause firmware node reference's argument count out of range if
directly assign DT node reference's argument count to firmware's.
drivers/of/property.c:of_fwnode_get_reference_args() is doing the direct
assignment, so may cause firmware's argument count @args->nargs got out
of range, namely, in [9, 16].
Fix by increasing NR_FWNODE_REFERENCE_ARGS to 16 to meet DT requirement.
Will align both macros later to avoid such inconsistency.
Fixes: 3e3119d308 ("device property: Introduce fwnode_property_get_reference_args")
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://lore.kernel.org/r/20250225-fix_arg_count-v4-1-13cdc519eb31@quicinc.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87886b32d6 ]
disable_irq_nosync_lockdep() disables interrupts with lockdep enabled to
avoid false positive reports by lockdep that a certain lock has not been
acquired with disabled interrupts. The user of this macros expects that
a lock can be acquried without disabling interrupts because the IRQ line
triggering the interrupt is disabled.
This triggers a warning on PREEMPT_RT because after
disable_irq_nosync_lockdep.*() the following spinlock_t now is acquired
with disabled interrupts.
On PREEMPT_RT there is no difference between spin_lock() and
spin_lock_irq() so avoiding disabling interrupts in this case works for
the two remaining callers as of today.
Don't disable interrupts on PREEMPT_RT in disable_irq_nosync_lockdep.*().
Closes: https://lore.kernel.org/760e34f9-6034-40e0-82a5-ee9becd24438@roeck-us.net
Fixes: e8106b941c ("[PATCH] lockdep: core, add enable/disable_irq_irqsave/irqrestore() APIs")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Suggested-by: "Steven Rostedt (Google)" <rostedt@goodmis.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20250212103619.2560503-2-bigeasy@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
