After the change from mdio polling to irq, it became necessary to
restore the interrupt mask after resetting the chip in fec_stop().
Otherwise, with all irqs disabled, no communication with the PHY will be
possible after e.g. un-/replugging the cable and the device gets
stalled.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_iomap() can fail, handle this case and return -ENOMEM from probe
function.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Workqueue can now handle high concurrency. Use system_nrt_wq
instead of slow-work.
* Updated is_valid_oplock_break() to not call cifs_oplock_break_put()
as advised by Steve French. It might cause deadlock. Instead,
reference is increased after queueing succeeded and
cifs_oplock_break() briefly grabs GlobalSMBSeslock before putting
the cfile to make sure it doesn't put before the matching get is
finished.
* Anton Blanchard reported that cifs conversion was using now gone
system_single_wq. Use system_nrt_wq which provides non-reentrance
guarantee which is enough and much better.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Steve French <sfrench@samba.org>
Cc: Anton Blanchard <anton@samba.org>
Make fscache operation to use only workqueue instead of combination of
workqueue and slow-work. FSCACHE_OP_SLOW is dropped and
FSCACHE_OP_FAST is renamed to FSCACHE_OP_ASYNC and uses newly added
fscache_op_wq workqueue to execute op->processor().
fscache_operation_init_slow() is dropped and fscache_operation_init()
now takes @processor argument directly.
* Unbound workqueue is used.
* fscache_retrieval_work() is no longer necessary as OP_ASYNC now does
the equivalent thing.
* sysctl fscache.operation_max_active added to control concurrency.
The default value is nr_cpus clamped between 2 and
WQ_UNBOUND_MAX_ACTIVE.
* debugfs support is dropped for now. Tracing API based debug
facility is planned to be added.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David Howells <dhowells@redhat.com>
Make fscache object state transition callbacks use workqueue instead
of slow-work. New dedicated unbound CPU workqueue fscache_object_wq
is created. get/put callbacks are renamed and modified to take
@object and called directly from the enqueue wrapper and the work
function. While at it, make all open coded instances of get/put to
use fscache_get/put_object().
* Unbound workqueue is used.
* work_busy() output is printed instead of slow-work flags in object
debugging outputs. They mean basically the same thing bit-for-bit.
* sysctl fscache.object_max_active added to control concurrency. The
default value is nr_cpus clamped between 4 and
WQ_UNBOUND_MAX_ACTIVE.
* slow_work_sleep_till_thread_needed() is replaced with fscache
private implementation fscache_object_sleep_till_congested() which
waits on fscache_object_wq congestion.
* debugfs support is dropped for now. Tracing API based debug
facility is planned to be added.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David Howells <dhowells@redhat.com>
It turns out that there is a bit in the _CST for Intel FFH C3
that tells the OS if we should be checking BM_STS or not.
Linux has been unconditionally checking BM_STS.
If the chip-set is configured to enable BM_STS,
it can retard or completely prevent entry into
deep C-states -- as illustrated by turbostat:
http://userweb.kernel.org/~lenb/acpi/utils/pmtools/turbostat/
ref: Intel Processor Vendor-Specific ACPI Interface Specification
table 4 "_CST FFH GAS Field Encoding"
Bit 1: Set to 1 if OSPM should use Bus Master avoidance for this C-state
https://bugzilla.kernel.org/show_bug.cgi?id=15886
Signed-off-by: Len Brown <len.brown@intel.com>
We should always go to the MDS for readdir on the hidden snapdir. The
set of snapshots can change at any time; the client can't trust its cache
for that.
Signed-off-by: Sage Weil <sage@newdream.net>
Add a new rt attribute, RTA_MARK, and use it in
rt_fill_info()/inet_rtm_getroute() to support following commands :
ip route get 192.168.20.110 mark NUMBER
ip route get 192.168.20.108 from 192.168.20.110 iif eth1 mark NUMBER
ip route list cache [192.168.20.110] mark NUMBER
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the interface has IPv6 disabled, don't add a multicast or
link-local route since we won't be adding a link-local address.
Reported-by: Mahesh Kelkar <maheshkelkar@gmail.com>
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once a work starts execution, its data contains the cpu number it was
on instead of pointing to cwq. This is added by commit 7a22ad75
(workqueue: carry cpu number in work data once execution starts) to
reliably determine the work was last on even if the workqueue itself
was destroyed inbetween.
Whether data points to a cwq or contains a cpu number was
distinguished by comparing the value against PAGE_OFFSET. The
assumption was that a cpu number should be below PAGE_OFFSET while a
pointer to cwq should be above it. However, on architectures which
use separate address spaces for user and kernel spaces, this doesn't
hold as PAGE_OFFSET is zero.
Fix it by using an explicit flag, WORK_STRUCT_CWQ, to mark what the
data field contains. If the flag is set, it's pointing to a cwq;
otherwise, it contains a cpu number.
Reported on s390 and microblaze during linux-next testing.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Sachin Sant <sachinp@in.ibm.com>
Reported-by: Michal Simek <michal.simek@petalogix.com>
Reported-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Tested-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Tested-by: Michal Simek <monstr@monstr.eu>
make version 3.80 doesn't support "else ifdef" on the same line, also it
doesn't support unindented nested constructs.
Build fails with:
Makefile:608: Extraneous text after `else' directive
Makefile:611: *** only one `else' per conditional. Stop.
This patch fixes the build for make 3.80.
Cc: Ingo Molnar <mingo@elte.hu>,
Cc: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <1278430783-17259-1-git-send-email-conny.seidel@amd.com>
Signed-off-by: Conny Seidel <conny.seidel@amd.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Make pskb_expand_head() check ip_summed to make sure csum_start is really
csum_start and not csum before adjusting it.
This fixes a bug I encountered using a Sun Quad-Fast Ethernet card and VLANs.
On my configuration, the sunhme driver produces skbs with differing amounts
of headroom on receive depending on the packet size. See line 2030 of
drivers/net/sunhme.c; packets smaller than RX_COPY_THRESHOLD have 52 bytes
of headroom but packets larger than that cutoff have only 20 bytes.
When these packets reach the VLAN driver, vlan_check_reorder_header()
calls skb_cow(), which, if the packet has less than NET_SKB_PAD (== 32) bytes
of headroom, uses pskb_expand_head() to make more.
Then, pskb_expand_head() needs to adjust a lot of offsets into the skb,
including csum_start. Since csum_start is a union with csum, if the packet
has a valid csum value this will corrupt it, which was the effect I observed.
The sunhme hardware computes receive checksums, so the skbs would be created
by the driver with ip_summed == CHECKSUM_COMPLETE and a valid csum field, and
then pskb_expand_head() would corrupt the csum field, leading to an "hw csum
error" message later on, for example in icmp_rcv() for pings larger than the
sunhme RX_COPY_THRESHOLD.
On the basis of the comment at the beginning of include/linux/skbuff.h,
I believe that the csum_start skb field is only meaningful if ip_csummed is
CSUM_PARTIAL, so this patch makes pskb_expand_head() adjust it only in that
case to avoid corrupting a valid csum value.
Please see my more in-depth disucssion of tracking down this bug for
more details if you like:
http://puellavulnerata.livejournal.com/112186.htmlhttp://puellavulnerata.livejournal.com/112567.htmlhttp://puellavulnerata.livejournal.com/112891.htmlhttp://puellavulnerata.livejournal.com/113096.htmlhttp://puellavulnerata.livejournal.com/113591.html
I am not subscribed to this list, so please CC me on replies.
Signed-off-by: Andrea Shepard <andrea@persephoneslair.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark Wagner reported OOM symptoms when sending UDP traffic over
a macvtap link to a kvm receiver.
This appears to be caused by the fact that macvtap packet queues
are unlimited in length. This means that if the receiver can't
keep up with the rate of flow, then we will hit OOM. Of course
it gets worse if the OOM killer then decides to kill the receiver.
This patch imposes a cap on the packet queue length, in the same
way as the tuntap driver, using the device TX queue length.
Please note that macvtap currently has no way of giving congestion
notification, that means the software device TX queue cannot be
used and packets will always be dropped once the macvtap driver
queue fills up.
This shouldn't be a great problem for the scenario where macvtap
is used to feed a kvm receiver, as the traffic is most likely
external in origin so congestion notification can't be applied
anyway.
Of course, if anybody decides to complain about guest-to-guest
UDP packet loss down the track, then we may have to revisit this.
Incidentally, this patch also fixes a real memory leak when
macvtap_get_queue fails.
Chris Wright noticed that for this patch to work, we need a
non-zero TX queue length. This patch includes his work to change
the default macvtap TX queue length to 500.
Reported-by: Mark Wagner <mwagner@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use %p instead of %08x in printk().
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Acked-by: David Brown <davidb@codeaurora.org>
Acked-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
protocol drivers such as BT, FM and GPS when registering
to ST now provide their own private data which they expect
when their functions namely registration completed & receive
are called.
Also upon tty_close, set protos_registered count to 0, although
all protocols are marked un-registered.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
cleanup the code commenting in the headers/structures,
also cleanup few inline commenting in the function
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace looping on the data buffers and printk-ing by
print_hex_dump.
Also replace most of the pr_info by pr_debug to reduce logging at
default loglevels (7 in our case..)
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
remove custom error code definitions from the header and
make use of the agreed upon linux error codes.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>