This patch adds a new flags argument to bitbang_txrx_be_cpha0 and
bitbang_txrx_be_cpha1 transfer functions. This enables support for
SPI_MASTER_NO_{TX,RX} transfer modes. The change should have no impact
on speed of the existing drivers. bitbank_txrx_* functions are usually
inlined into the drivers. When the argument is equal to constant zero,
the optimizer would be able to eliminate the dead code (flags checks)
easily. Tested on ARM and GCC 4.4.x and in all cases the checks were
eliminated in the inlined function.
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This change fixes 8-bit transfers and RX-only transfers. The
SPI100k framework requires minimum 16-bit words to be written, so 8-bit
transfers must be shited by 8 bits and sent out as a 16-bit word.
Additionally, receive-only transfers were failing due to the
perceived need to fill the TX buffer with something. This is in
fact not needed.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Modification of the mmc_spi driver to use the SPI bus locking API.
With this, the mmc_spi driver can be used together with other SPI
devices on the same SPI bus. The exclusive access to the SPI bus is
now managed in the SPI layer. The counting of chip selects in the probe
function is no longer needed.
Signed-off-by: Ernst Schwab <eschwab@online.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Matt Fleming <matt@console-pimps.org>
Tested-by: Antonio Ospite <ospite@studenti.unina.it>
As the kernel has no way to know whether a key was released
while the system was asleep, keys need to be reported released
as the system is resumed, lest autorepeat set in.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
ADS7845 is a controller for 5-wire touch screens and somewhat
different from 7846. It requires three serial communications to
accomplish one complete conversion. Unlike 7846 it doesn't allow
Z1-/Z2- position measurement.
The patch extends the ads7846 driver to also support ads7845.
The packet struct is extended to contain needed command and
conversion buffers. ads7846_rx() and ads7846_rx_val() now
differentiate between 7845 and 7846 case. ads7846_probe() is
modified to setup ads7845 specific command and conversion
messages and to switch ads7845 into power-down mode, since
this is needed to be prepared to respond to pendown interrupts.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Suspending and resuming the device should be separate from enabling
and disabling it through sysfs attribute and thus should not alter
ac->disabled flag.
[michael.hennerich@analog.com: various fixups]
Tested-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some input events users such as Android require BTN_TOUCH events.
Implement EV_KEY/BTN_TOUCH and make sure that the release event
is not erroneous scheduled without a preceding valid touch.
Avoid duplicated BTN_TOUCH events, even though input core filters
them.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The ad7879 driver is using the old bus method of only supporting one
at a time (I2C or SPI). So refactor it like the other input drivers
that support multiple busses simultaneously.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
While doing some performance counter validation tests on some
assembly language programs I noticed that the "branches:u"
count was very wrong on AMD machines.
It looks like the wrong event was selected.
Signed-off-by: Vince Weaver <vweaver1@eecs.utk.edu>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: <stable@kernel.org>
LKML-Reference: <alpine.DEB.2.00.1007011526010.23160@cl320.eecs.utk.edu>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
virtio net will never try to overflow the TX ring, so the only reason
add_buf may fail is out of memory. Thus, we can not stop the
device until some request completes - there's no guarantee anything
at all is outstanding.
Make the error message clearer as well: error here does not
indicate queue full.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (...and avoid TX_BUSY)
Cc: stable@kernel.org # .34.x (s/virtqueue_/vi->svq->vq_ops->/)
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently fill all of RX ring, then add_buf
returns ENOSPC, which gets mis-detected as an out of
memory condition and causes us to reschedule the work,
and so on forever. Fix this by oom = err == -ENOMEM;
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org # .34.x
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resolves a number of issues in the statistics gathering of
the s2io driver.
On Xframe adapters, the received multicast statistics counter includes
pause frames which are not indicated to the driver. This can cause
issues where the multicast packet count is higher than what has actually
been received, possibly higher than the number of packets received.
The driver software counters are replaced with the adapter hardware
statistics for rx_packets, rx_bytes, and tx_bytes. It also uses the
overflow registers to determine if the statistics wrapped the 32bit
register (removing the window of having a statistic value less than the
previous call). rx_length_errors statistic now includes undersized
packets in addition to oversized packets in its counting. Finally,
rx_crc_errors are now being counted.
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix kernel-doc warnings in linux/net.h:
Warning(include/linux/net.h:151): No description found for parameter 'wq'
Warning(include/linux/net.h:151): Excess struct/union/enum/typedef member 'fasync_list' description in 'socket'
Warning(include/linux/net.h:151): Excess struct/union/enum/typedef member 'wait' description in 'socket'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reducing real_num_queues needs to flush the qdisc otherwise
skbs with queue_mappings greater then real_num_tx_queues can
be sent to the underlying driver.
The flow for this is,
dev_queue_xmit()
dev_pick_tx()
skb_tx_hash() => hash using real_num_tx_queues
skb_set_queue_mapping()
...
qdisc_enqueue_root() => enqueue skb on txq from hash
...
dev->real_num_tx_queues -= n
...
sch_direct_xmit()
dev_hard_start_xmit()
ndo_start_xmit(skb,dev) => skb queue set with old hash
skbs are enqueued on the qdisc with skb->queue_mapping set
0 < queue_mappings < real_num_tx_queues. When the driver
decreases real_num_tx_queues skb's may be dequeued from the
qdisc with a queue_mapping greater then real_num_tx_queues.
This fixes a case in ixgbe where this was occurring with DCB
and FCoE. Because the driver is using queue_mapping to map
skbs to tx descriptor rings we can potentially map skbs to
rings that no longer exist.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calling qdisc_reset() the qdisc lock needs to be held. In
this case there is at least one driver i4l which is using this
without holding the lock. Add the locking here.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some ocasions the function qlge_io_resume() tries to add a
pending timer, which causes the system to hit the BUG() on
add_timer() function.
This patch removes the timer during the EEH recovery.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently qlge driver calls add_timer() instead of mod_timer().
This patch changes add_timer() to mod_timer(), which seems a better
solution.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev_printk() follows the net_device's parent device pointer, so
we must set that earlier than we previously did.
Reported-by: Luís Picciochi Oliveira <pitxyoki@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit c17b274dc2.
That change was reported to break rndis_wlan support for the WUSB54GS.
Reported-by: Luís Picciochi Oliveira <pitxyoki@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert ppc4xx adma driver to use new node pointer location
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
While here, fixes the mailing list for i5400_edac
Acked-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As Nehalem/Nehalem-EP/Westmere devices uses several devices for the same
functionality (memory controller), the default way of proping devices doesn't
work. So, instead of a per-device probe, all devices should be probed at once.
This means that we should block any new attempt of probe, otherwise, it will
try to register the same device several times.
Acked-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On Nehalem/Nehalem-EP/Westmere, the first QPI device is the last PCI bus.
The last bus is generally at 0x3f or 0xff, but there are also other systems
using different setups. For example, HP Z800 has 0x7f as the last bus.
This patch adds a logic to discover the last bus, dynamically detecting it
at runtime.
Acked-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For newer devices (6000g2a and 6000g2b), the sensitivity table send to
uCode require additional table entries to help sensitivity calibration.
All the additional entries has fix data for now, but do expect the value
will be change in the future when device become more stable.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Code clean up to change name from having 5000 as part of name which easy
to confuse and think it is for 5000 series devices to more
generic _agn name since it is being used by multiple _agn devices.
No functional changes.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
"Flush" request can come from two different sources, it can either from
mac80211, or from device when the operation is needed. Here
adding the support for device issue "flush" request.
When receive tx complete with status is TX_STATUS_FAIL_RFKILL_FLUSH,
issue REPLY_TXFIFO_FLUSH command to uCode to flush out all the tx frames
in queues.
In this condition, since mac80211 has no knowledge of "flush" operation,
driver need to stop all the tx queues and wait for the operation
completed before wake up the queues for frames transmission.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Adding flush callback support in the driver. Two type of flush can be
issued by mac80211:
1. drop = true: frame drop is ok, issue REPLY_TXFIFO_FLUSH host command
to uCode to drop all the frames in tx fifo queues; then return the
control back to mac80211
2. drop = false: wait for either all the frames in tx fifo queues been
transmitted, or timeout; then return the control back to mac80211
If the flush request coming from mac80211, mac80211 will make sure there
are no additional frames push down to driver before flush operation is
completed.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When parsing TLV during loading firmware, if encounter any TLV error,
log the error message to help debugging.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
fw_restart module parameter was broken by the recent check for stuck
queue patch, driver check the fx_restart module parameter
before reload the firmware; but the stuck queue timer kick in after
firmware error and reload the firmware even fw_restart=0. In this case,
driver should not reload the firmware, it is important to help debugging
uCode error.
The only case we can ignore the module parameter is when user request
firmware reload from debugfs, which can bypass the checking and perform
firmware reload all the time.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The check should be against current top2 rate, instead of
current top rate.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The throughput should be considered when updating rate
with best probability.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit eed8e22f01 added support for using
multicast key lookup to support per-vif/sta keys for AP and ad-hoc.
Unfortunately, it also introduced a crash in ad-hoc mode when the sta
pointer is NULL, which happens when setting up an interface with WEP
keys. This patch fixes it by falling back to the assigned key index.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_check_alive() occasionally returns false, as the hardware
is still processing data in a specific state. Fix this issue by
repeating the test a few times with longer delay inbetween attempts.
This gets rid of excessive hardware resets that appear frequently on
some AR9132 based devices, but could also happen on AR9280.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Björn Smedman <bjorn.smedman@venatech.se>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This refactors the noise floor range checks to make them generic,
and adds proper ranges for each supported chip type.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This includes the following changes/fixes:
- a bugfix for stuck beacon issues
- timing changes for improved performance
- AGC setting improvements
- fixes for high temperature issues on some chips
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This format is generated by the initval tool, available at:
git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/initvals-tool.git
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When there is a firmware error or the firmware is reloaded for some other
reason we currently clear all station information, including keys
associated with them. A problem is that we do not clear some other
information regarding keys that are not stored in the station structs.
The consequence of this is that when the device is reconfigured after the
firmware reload we can, among other things, run out of key indices.
This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=16232http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2221
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
