arch/m68knommu/mm/fault.c:39: WARNING: space prohibited between function name and open parenthesis '('
arch/m68knommu/mm/fault.c:47: WARNING: braces {} are not necessary for any arm of this statement
arch/m68knommu/mm/fault.c:51: ERROR: space required after that ',' (ctx:VxV)
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
While it is explained in the long help text, meaning of '0' for RAMSIZE
is easily overlooked because is not mentioned in the short help text.
Add that.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Remove the un-used mcfsmc.h. All ColdFire platforms that use SMC ethernet
devices are platform enabled to use the smc91x driver.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire based NETtel boards use the SMC9196 ethernet devices.
Switch to using a platform setup for these parts using the smc91x driver.
The init code is taken strait out of arch/m68k/include/asm/mcfsmc.h,
just cleaned up a bit.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The Freescale M5249EVB board is fitted with an SMC LAN91c11 ethernet
device. Add platform support to the M5249EVB setup code to support this.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The TASK_SIZE define is used in some places as a limit on the size of
the virtual address space of a process. On non-MMU systems those addresses
used in comparison will be physical addresses, and they could be anywhere
in the 32bit physical address space. So for !CONFIG_MMU systems set the
TASK_SIZE to the maximum physical address.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Commit 8b505ca8e2 ("serial: 68328serial.c:
remove BAUD_TABLE_SIZE macro") misses one use of BAUD_TABLE_SIZE. So the
resulting 68328serial.c does not compile:
drivers/serial/68328serial.c: In function ‘m68328_console_setup’:
drivers/serial/68328serial.c:1439: error: ‘BAUD_TABLE_SIZE’ undeclared (first use in this function)
drivers/serial/68328serial.c:1439: error: (Each undeclared identifier is reported only once
drivers/serial/68328serial.c:1439: error: for each function it appears in.)
Fix that last use of it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Cc: <stable@kernel.org>
Add DMA Engine API driver for the PL330 DMAC.
This driver is supposed to be reusable by various
platforms that have one or more PL330 DMACs.
Atm, DMA_SLAVE and DMA_MEMCPY capabilities have been
implemented.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Reviewed-by: Linus Walleij <linus.walleij@stericsson.com>
[dan.j.williams@intel.com: missing slab.h and ->device_control() fixups]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The hists__tty_browse_tree function was created with the loop to print
all events, and its equivalent, hists__tui_browse_tree, was created in a
similar fashion, where it is possible to switch among the multiple
events, if present, using TAB to go the next event, and shift+TAB
(UNTAB) to go to the previous.
The report TUI now shows as the window title the name of the event and a
leak was fixed wrt pstacks.
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Cc: Tom Zanussi <tzanussi@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It was assuming that the cache was always available and also wasn't
checking if the file found in the build id cache was just a kallsyms
file, that is not supported by objdump for disassembly.
Reported-by: Ingo Molnar <mingo@elte.hu>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Cc: Tom Zanussi <tzanussi@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
drivers/gpu/drm/nouveau/nv40_graph.c: In function `nv40_graph_init':
drivers/gpu/drm/nouveau/nv40_graph.c:400: warning: the frame size of 1184 bytes is larger than 1024 bytes
drivers/gpu/drm/radeon/radeon_atombios.c: In function `radeon_get_atom_connector_info_from_supported_devices_table':
drivers/gpu/drm/radeon/radeon_atombios.c:857: warning: the frame size of 1872 bytes is larger than 1024 bytes
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When CONFIG_ACPI_BUTTON=m (and probably when ACPI_BUTTON is not enabled)
and NOUVEAU is built-in (not as a loadable module):
nouveau_connector.c:(.text+0xe17ce): undefined reference to `acpi_lid_open'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I think it's good to release the AGP bridge at suspend
and reacquire it at resume. Also fix :
https://bugzilla.kernel.org/show_bug.cgi?id=15969
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The current SH7372 setup code registers 7 SCIF ports, which is wrong.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SCIFB ports have a slightly different register layout and a different FIFO
size from SCIFA ports, in DMA mode they have to be treated just like SCIFA.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
ap4evb uses an LCD, connected to the SoC over the MIPI bus. This patch adds
platform data to configure this display and a static clock activation.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some SH-mobile SoCs have a MIPI DSI controller, that can be used to connect
MIPI displays to LCDC. This patch adds a platform driver for SH-mobile MIPI DSI
unit. It uses existing hooks in the sh_mobile_lcdcfb.c driver for display
activation and deactivation.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The LCDC block is allowed to use one of the two output data formats, when used
with MIPI DSI: RGB24 and YUV422. YUV422 is not currently handled by the LCDC
driver, but we have to add a define for it for MIPI.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Define clock objects for switching on and off clocks for LCDC0, LCDC1 and MIPI
DSI-Tx.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This header adds defines for MIPI DSI and DCS commands and data formats. See
http://www.mipi.org/ for details.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The build scripts inadvertently dropped this down to 29-bit, fix it
back up.
Reported-by: Raul Porcel <armin76@gentoo.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fixup the defconfig post the latest moves, so ARCH_S5PC1XX becomes
ARCH_S5PC100 which is sufficient to get the system building.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Between problems with Kconfig and merging commits from several
different sources, it seems the s5pc100 build's move from plat-s5pc11
has had a few problems.
Since I do not have the trees to rebuild this quickly, the easiest
thing is to simply fix the errors found once the s5pc100_defconfig
actually builds.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Samsung's Soc S5PC100 has three PL330 DMACs. First is dedicated for
Memory->Memory data transfer while the other two meant for data
transfer with peripherals.
Define and add latter two PL330 DMACs as platform devices on the
S5PC100 platform.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Somewhere during the latest platform cleanups the IRQ_EINT definition
got broken, so fix it by replacing it in <mach/irqs.h>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
When saving GPIOs during suspend/resume we need skip missing GPIO banks, not
trying get corresponding chip again and again in infinite loop.
Signed-off-by: Jiri Pinkava <jiri.pinkava@vscht.cz>
[ben-linux@fluff.org: shorten subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Get rid of the duplicated entries in prefix_codes[]
to eliminate redundant checks by skip_prefix().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Pekka Paalanen <pq@iki.fi>
LKML-Reference: <1274140110-5841-1-git-send-email-akinobu.mita@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Only read potentially matching names into the target buffer, all
obviously non matching names don't need to be read into the
target buffer.
Signed-off-by: Phillip Lougher <phillip@lougher.demon.co.uk>
The timeout value is in jiffies, so it should be using HZ, not a plain
number. As '10000' is ambiguous, 1HZ is used as conservative default.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Valentin Yakovenkov <yakovenkov@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Architectures that handle DMA-non-coherent memory need to set
ARCH_KMALLOC_MINALIGN to make sure that kmalloc'ed buffer is DMA-safe:
the buffer doesn't share a cache with the others.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
