If interface is down, mac address request are not sent to fw
but it is getting add in driver mac list.
Driver mac list should be in sync with fw i.e addresses communicated
to fw.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported in <https://bugzilla.kernel.org/show_bug.cgi?id=15355>, r6040_
multicast_list currently crashes. This is due a wrong maximum of multicast
entries. This patch fixes the following issues with multicast:
- number of maximum entries if off-by-one (4 instead of 3)
- the writing of the hash table index is not necessary and leads to invalid
values being written into the MCR1 register, so the MAC is simply put in a non
coherent state
- when we exceed the maximum number of mutlticast address, writing the
broadcast address should be done in registers MID_1{L,M,H} instead of
MID_O{L,M,H}, otherwise we would loose the adapter's MAC address
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I don't think this can be abused in this case but do things properly.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
write is optional for a tty device. Check that we have a write op rather
than calling NULL.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As pointed by Randy Dunlap, we must include linux/proc_fs.h in
net/core/dev_addr_lists.c, regardless of CONFIG_PROC_FS
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>,
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first argument should be called ha, not mclist. All callers use the
name "ha", but if they used a different name, there would be a compile
error.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an unused hook in SMACK so remove it.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: James Morris <jmorris@namei.org>
trying to grep everything that messes with a sk_security_struct isn't easy
since we don't always call it sksec. Just rename everything sksec.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
rwsems can be used with IRQs disabled, particularily in early boot
before IRQs are enabled. Currently the spin_unlock_irq() usage in the
slow-patch will unconditionally enable interrupts and cause problems
since interrupts are not yet initialized or enabled.
This patch uses save/restore versions of IRQ spinlocks in the slowpath
to ensure interrupts are not unintentionally disabled.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If nfs atomic open implementation ends up doing open request from
->d_revalidate() codepath and gets an error from server, return that error
to caller explicitly and don't bother with lookup_instantiate_filp() at all.
->d_revalidate() can return an error itself just fine...
See
http://bugzilla.kernel.org/show_bug.cgi?id=15674http://marc.info/?l=linux-kernel&m=126988782722711&w=2
for original report.
Reported-by: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The intent here is to check the "mfrpl->mapped_page_list" allocation.
We checked "mfrpl->ibfrpl.page_list" earlier.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
cap.max_inline_data is incorrectly set in init_attr instead of attr.
Set it in attr so subsequent init_attr.cap assignment will get the
correct value.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When manually assigning the path records to use for a connection, save
the number of paths that were set. Otherwise, checks against num_path
will show 0, even though path record data is available.
This was discovered by manually setting the path records from user
space, then querying the kernel to see if the correct path records
were assigned, only to discover that the kernel returned 0 path
records to the query.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
WEP crypto was broken, but upon finding the problem
it is evident that other things were broken by the
paged RX patch as well.
To fix it, for now move the linearising in front.
This means that we linearise all frames, which is
not at all what we want, but at least it fixes the
problem for now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
98e12b5a6e ("ARM: Fix decompressor's kernel size estimation for
ROM=y") broke the Thumb-2 decompressor because it added an entry in the
LC0 table but didn't adjust the offset the Thumb-2 code uses to load the
SP from that table. Fix it.
Cc: stable <stable@kernel.org>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The functions ep93xx_gpio_update_int_params and ep93xx_gpio_int_mask
are not exported and should be static. This was overlooked when
moving the code from core.c.
Also, change a comment to better indicate what the code is for.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds myself as maintainer of the U300 machine and associated
system-on-chip drivers.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Added missing down on the memMap->lock semaphore. Also fixed a return
statement so that we always exit with an up (i.e. early exit via return
is not allowed)
Signed-off-by: Leo Hao Chen <leochen@broadcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A few places in mac80211 do not currently acquire
the sta lock for RX aggregation, but they should.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The aggregation code has a number of quirks, like
inventing an unneeded WLAN_BACK_TIMER value and
leaking memory under certain circumstances during
station destruction. Fix these issues by using
the regular aggregation session teardown code and
blocking new aggregation sessions, all before the
station is really destructed.
As a side effect, this gets rid of the long code
block to destroy aggregation safely.
Additionally, rename tid_state_rx which can only
have the values IDLE and OPERATIONAL to
tid_active_rx to make it easier to understand
that there is no bitwise stuff going on on the
RX side -- the TX side remains because it needs
to keep track of the driver and peer states.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I want to use it during station destruction as well
so rename it to WLAN_STA_BLOCK_BA which is also the
only use of it now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All callers of ieee80211_sta_stop_rx_ba_session can
just call __ieee80211_stop_rx_ba_session instead
because they already have the station struct, so do
that and remove ieee80211_sta_stop_rx_ba_session.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All other places except one in the TX path, which
has BHs disabled, and it also cannot be locked from
interrupts so disabling IRQs is not necessary.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a station w/o a key is destroyed, or when
a driver submits work for a station and thereby
references it again, it seems like potentially
we could reference the station structure while
it is being destroyed.
Wait for an RCU grace period to elapse before
finishing destroying the station after we have
removed the station from the driver and from
the hash table etc., even in the case where no
key is associated with the station.
Also, there's no point in deleting the plink
timer here since it'll be properly deleted just
a bit later.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for a modified newer version of AR9285
chipsets.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211 is quite strict on allowing authentication and association
commands only in certain states. In order to meet these requirements,
user space applications may need to clear authentication or
association state in some cases. Currently, this can be done with
deauth/disassoc command, but that ends up sending out Deauthentication
or Disassociation frame unnecessarily. Add a new nl80211 attribute to
allow this sending of the frame be skipped, but with all other
deauth/disassoc operations being completed.
Similar state change is also needed for IEEE 802.11r FT protocol in
the FT-over-DS case which does not use Authentication frame exchange
in a transition to another BSS. For this to work with cfg80211, an
authentication entry needs to be created for the target BSS without
sending out an Authentication frame. The nl80211 authentication
command can be used for this purpose, too, with the new attribute to
indicate that the command is only for changing local state. This
enables wpa_supplicant to complete FT-over-DS transition successfully.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Better use the macro for consistency, the content is the same anyway.
Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is an Adaptive Noise Imunity (ANI) implementation for ath5k. I have looked
at both ath9k and HAL sources (they are nearly the same), and even though i
have implemented some things differently, the basic algorithm is practically
the same, for now. I hope that this can serve as a clean start to improve the
algorithm later.
This also adds a possibility to manually control ANI settings, right now only
thru a debugfs file:
* set lowest sensitivity (=highest noise immunity):
echo sens-low > /sys/kernel/debug/ath5k/phy0/ani
* set highest sensitivity (=lowest noise immunity):
echo sens-high > /sys/kernel/debug/ath5k/phy0/ani
* automatically control immunity (default):
echo ani-on > /sys/kernel/debug/ath5k/phy0/ani
* to see the parameters in use and watch them change:
cat /sys/kernel/debug/ath5k/phy0/ani
Manually setting sensitivity will turn the automatic control off. You can also
control each of the five immunity parameters (noise immunity, spur immunity,
firstep, ofdm weak signal detection, cck weak signal detection) manually thru
the debugfs file.
This is tested on AR5414 and nearly doubles the thruput in a noisy 2GHz band.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-tip:
x86: Fix double enable_IR_x2apic() call on SMP kernel on !SMP boards
x86: Increase CONFIG_NODES_SHIFT max to 10
ibft, x86: Change reserve_ibft_region() to find_ibft_region()
x86, hpet: Fix bug in RTC emulation
x86, hpet: Erratum workaround for read after write of HPET comparator
bootmem, x86: Fix 32bit numa system without RAM on node 0
nobootmem, x86: Fix 32bit numa system without RAM on node 0
x86: Handle overlapping mptables
x86: Make e820_remove_range to handle all covered case
x86-32, resume: do a global tlb flush in S4 resume
This hushes the following warning:
arch/arm/mach-davinci/include/mach/da8xx.h:104: warning: ‘struct platform_device’
declared inside parameter list
arch/arm/mach-davinci/include/mach/da8xx.h:104: warning: its scope is only this
definition or declaration, which is probably not what you want
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Slab lacks any memory hotplug support for nodes that are hotplugged
without cpus being hotplugged. This is possible at least on x86
CONFIG_MEMORY_HOTPLUG_SPARSE kernels where SRAT entries are marked
ACPI_SRAT_MEM_HOT_PLUGGABLE and the regions of RAM represent a seperate
node. It can also be done manually by writing the start address to
/sys/devices/system/memory/probe for kernels that have
CONFIG_ARCH_MEMORY_PROBE set, which is how this patch was tested, and
then onlining the new memory region.
When a node is hotadded, a nodelist for that node is allocated and
initialized for each slab cache. If this isn't completed due to a lack
of memory, the hotadd is aborted: we have a reasonable expectation that
kmalloc_node(nid) will work for all caches if nid is online and memory is
available.
Since nodelists must be allocated and initialized prior to the new node's
memory actually being online, the struct kmem_list3 is allocated off-node
due to kmalloc_node()'s fallback.
When an entire node would be offlined, its nodelists are subsequently
drained. If slab objects still exist and cannot be freed, the offline is
aborted. It is possible that objects will be allocated between this
drain and page isolation, so it's still possible that the offline will
still fail, however.
Acked-by: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: mixart: range checking proc file
ALSA: hda - Fix a wrong array range check in patch_realtek.c
ALSA: ASoC: move dma_data from snd_soc_dai to snd_soc_pcm_stream
ALSA: hda - Enable amplifiers on Acer Inspire 6530G
ASoC: Only do WM8994 bias off transition from standby
ASoC: Don't use DCS_DATAPATH_BUSY for WM hubs devices
ASoC: Don't do runtime wm_hubs DC servo updates if using offset correction
ASoC: Support second DC servo readback method for wm_hubs
ASoC: Avoid wraparound in wm_hubs DC servo correction
ALSA: echoaudio - Eliminate use after free
ALSA: i2c: cleanup: change parameter to pointer
ALSA: hda - Add MSI blacklist for Aopen MZ915-M
ASoC: OMAP: Fix capture pointer handling for OMAP1510 to work correctly with recent ALSA PCM code
ALSA: hda - Update document about MSI and interrupts
ALSA: hda: Fix 0 dB offset for Lenovo Thinkpad models using AD1981
ALSA: hda - Add missing printk argument in previous patch
ASoC: Fix passing platform_data to ac97 bus users and fix a leak
ALSA: hda - Fix ADC/MUX assignment of ALC269 codec
ALSA: hda - Fix invalid bit values passed to snd_hda_codec_amp_stereo()
ASoC: wm8994: playback => capture
Order the debugfs statistics correctly. The values displayed through a
seq_printf() statement should be in the same order as the names in the
format string.
In the 'Lookups' line, objects created ('crt=') and lookups timed out
('tmo=') have their values transposed.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In NOMMU mode, the FRV segment handling is broken because KERNEL_DS ==
USER_DS. This causes tests of the following sort:
/* don't pin down non-user-based iovecs */
if (segment_eq(get_fs(), KERNEL_DS))
return NULL;
to malfunction.
To fix this, make USER_DS the top of RAM instead of the top of the non-IO
address space, and make KERNEL_DS one more than the top of the non-IO
address space.
Also get rid of FRV's __addr_ok() as nothing uses it.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hide uncached_access() when pgprot_noncached is not #defined. This prevents
the following warning:
CC drivers/char/mem.o
drivers/char/mem.c:229: warning: 'uncached_access' defined but not used
Repairs d7d4d849b4 ("drivers/char/mem.c:
cleanups").
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On exit paths in mxc_rtc_probe() method some resources are not freed
correctly.
This patch fixes:
* unrequested memory region containing imx RTC registers
* iounmap() isn't called on exit_free_pdata branch
* clock get rate is called for freed clock source
* clock isn't disabled on exit_put_clk branch
To simplify the fix managed device resources are used.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Presently, memcg's FILE_MAPPED accounting has following race with
move_account (happens at rmdir()).
increment page->mapcount (rmap.c)
mem_cgroup_update_file_mapped() move_account()
lock_page_cgroup()
check page_mapped() if
page_mapped(page)>1 {
FILE_MAPPED -1 from old memcg
FILE_MAPPED +1 to old memcg
}
.....
overwrite pc->mem_cgroup
unlock_page_cgroup()
lock_page_cgroup()
FILE_MAPPED + 1 to pc->mem_cgroup
unlock_page_cgroup()
Then,
old memcg (-1 file mapped)
new memcg (+2 file mapped)
This happens because move_account see page_mapped() which is not guarded
by lock_page_cgroup(). This patch adds FILE_MAPPED flag to page_cgroup
and move account information based on it. Now, all checks are synchronous
with lock_page_cgroup().
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reviewed-by: Balbir Singh <balbir@in.ibm.com>
Reviewed-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Andrea Righi <arighi@develer.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When we look into pagemap using page-types with option -p, the value of
pfn for hugepages looks wrong (see below.) This is because pte was
evaluated only once for one vma although it should be updated for each
hugepage. This patch fixes it.
$ page-types -p 3277 -Nl -b huge
voffset offset len flags
7f21e8a00 11e400 1 ___U___________H_G________________
7f21e8a01 11e401 1ff ________________TG________________
^^^
7f21e8c00 11e400 1 ___U___________H_G________________
7f21e8c01 11e401 1ff ________________TG________________
^^^
One hugepage contains 1 head page and 511 tail pages in x86_64 and each
two lines represent each hugepage. Voffset and offset mean virtual
address and physical address in the page unit, respectively. The
different hugepages should not have the same offset value.
With this patch applied:
$ page-types -p 3386 -Nl -b huge
voffset offset len flags
7fec7a600 112c00 1 ___UD__________H_G________________
7fec7a601 112c01 1ff ________________TG________________
^^^
7fec7a800 113200 1 ___UD__________H_G________________
7fec7a801 113201 1ff ________________TG________________
^^^
OK
More info:
- This patch modifies walk_page_range()'s hugepage walker. But the
change only affects pagemap_read(), which is the only caller of hugepage
callback.
- Without this patch, hugetlb_entry() callback is called per vma, that
doesn't match the natural expectation from its name.
- With this patch, hugetlb_entry() is called per hugepte entry and the
callback can become much simpler.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The log of commit edaac8e316 ("ratelimit:
Fix/allow use in atomic contexts"), indicates that we want to suppress the
callback when the trylock fails.
Signed-off-by: Yong Zhang <yong.zhang@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When __ratelimit() returns 1 this means that we can go ahead.
Signed-off-by: Yong Zhang <yong.zhang@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
