If two streams are started immediately after one another (such as a
playback and a recording stream), the call to set hw params fails with
EBUSY. This patch makes the call succeed, so playback and recording will
work properly.
Signed-off-by: David Henningsson <launchpad.web@epost.diwic.se>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The chipsets with the isa_dma_bridge_buggy set do not stop DMA during
DMA counter reads. The DMA counter is read in two 8-bit read steps
on x86 platform. Sometimes, such reads happen during higher byte
change so the lower byte is already decremented (rolled over) but
the higher byte is not. It introduces an error that position is
moved 256 bytes ahead of the true position. Thus, the next DMA
position read can return a lower value then the previous read.
If the DMA position is decreased (reversed) the ALSA subsystem is
tricked into the playback underrun error and resets the playback.
It results in a "pop" during a playback.
Work around the issue by reading the counter twice and choosing a higher
value.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The C4231 control set is a superset of the AD1848 control
set so reuse the CS4231 controls definitions for the AD1848.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
According to customer request, hp should be default to redirected mode,
i.e. PW4 connect select default to to MW0.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Logan Li <loganli@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To via_control_templates[].
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Logan Li <loganli@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As init verbs, vt17xx_volume_init_verb is a better place to hold them.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Logan Li <loganli@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With snd_hda_override_amp_caps.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Logan Li <loganli@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Rewrite nid_vol/mute assignment for clearity, and check line connection
before adding control for it.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Logan Li <loganli@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Rewrite nid_vol/mute assignment for clearity, and check line connection
before adding control for it.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Logan Li <loganli@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replaced with via_playback_multi_pcm_prepare/cleanup to support
multi-stream operations
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Logan Li <loganli@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
like seqassoc 0xff, seqassoc 0xf0 of vt1708 should override Port
Connectivity field into 'AC_JACK_PORT_COMPLEX'
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Logan Li <loganli@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
VT1708 does not support unsolicited response, but we need hp detect to
automute speaker. Implemented in workqueue.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Logan Li <loganli@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Smart 5.1 is for 3-jacks model, to reuse input pins as outputs.
While off, they act as "line out" / "line in" / "mic in".
While on, they acts as "line out" / "back left/right" / "center/lfe".
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Logan Li <loganli@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use hp_independent_mode_index to store hp index, and simplify function
via_independent_hp_put with it.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Logan Li <loganli@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For VT1708S and VT1702, deactivate "Headphone Playback Volume" and
"Headphone Playback Mute" control if "Independent HP" mode is OFF.
and rename VT1702 "Independent HP" text.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Logan Li <loganli@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For VT1708B, VT1708S and VT1702, enter low current mode if no analog
stream is opened and all aa path mute.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Logan Li <loganli@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enter low power state if AA-Path volume is muted.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Logan Li <loganli@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
according to customer request, VT1702 AA-Path max volume (12 dB) is too
high, so limit to 0 dB.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Logan Li <loganli@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
IS_VT17*_VENDORID macros are used nowhere, so clean them up.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Logan Li <loganli@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pass a module's .eh_frame section to the DWARF unwinder at module load
time so that the section's FDEs and CIEs can be registered with the
DWARF unwinder. This allows us to unwind the stack through module code
when generating backtraces.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Seemingly this support was missed when highmem was added, so
DEBUG_HIGHMEM wouldn't have checked the kmap_atomic type.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Bit testing (test, testset, testclear, testchange) for bit numbers
known at compile time returns a word with the tested-for bit set.
Change it to return a true boolean value so to make it consistent with
the out-of-line path and all the other bitops implementations.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make die() better match x86:
- add printing of the last accessed sysfs file
- ensure console_verbose() is called under the lock
- ensure we panic outside of oops_exit()
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
dump_mem and dump_backtrace were both using multiple printk statements
to print each line. With DEBUG_LL enabled, this causes OOPS to become
very difficult to read. Solve this by only using one printk per line.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In the multi-evt conversion for the SH-X3 proto CPU, IRLs were dropped
down to a single unique masking source, which ended up blowing up on
ILSEL-based IRQs which have special semantics that otherwise confuse the
intc code. While this does result in intc spewing about not having a
unique masking source, we don't really care.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The initialisation process differs for CONFIG_PMB and for
CONFIG_PMB_FIXED. For CONFIG_PMB_FIXED we need to register the PMB
entries that were allocated by the bootloader.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We need to map the gap between 0x00000000 and __MEMORY_START in the PMB,
as well as RAM.
With this change my 7785LCR board can switch to 32bit MMU mode at
runtime.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Eventually we'll have complete control over what physical memory gets
mapped where and we can probably do other interesting things. For now
though, when the MMU is in 32-bit mode, we map physical memory into the
P1 and P2 virtual address ranges with the same semantics as they have in
29-bit mode.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Unfortunately, at the time during in boot when we want to be setting up
the PMB entries, the kmem subsystem hasn't been initialised.
We now match pmb_map slots with pmb_entry_list slots. When we find an
empty slot in pmb_map, we set the bit, thereby acquiring the
corresponding pmb_entry_list entry. There is a benefit in using this
static array of struct pmb_entry's; we don't need to acquire any locks
in order to traverse the list of struct pmb_entry's.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There's no need to export the internal PMB functions for allocating,
freeing and modifying PMB entries, etc. This way we can restrict the
interface for PMB.
Also remove the static from pmb_init() so that we have more freedom in
setting up the initial PMB entries and turning on MMU 32bit mode.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
CONFIG_PMB will eventually allow the MMU to be switched between 29-bit
and 32-bit mode dynamically at runtime.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
To allow the MMU to be switched between 29bit and 32bit mode at runtime
some constants need to swapped for functions that return a runtime
value.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Replace the use of PHYSADDR() with __pa(). PHYSADDR() is based on the
idea that all addresses in P1SEG are untranslated, so we can access an
address's physical page as an offset from P1SEG. This doesn't work for
CONFIG_PMB/CONFIG_PMB_FIXED because pages in P1SEG and P2SEG are used
for PMB mappings and so can be translated to any physical address.
Likewise, replace a P1SEGADDR() use with virt_to_phys().
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Simplify set_pmb_entry() by removing the possibility of not finding a
free slot in the PMB. Instead we now allocate a slot in pmb_alloc() so
that if there are no free slots we fail at allocation time, rather than
in set_pmb_entry().
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>