check_topology() doesn't actually require alloc info - and running it
first means other passes don't have to catch btree read errors.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
The Volume Down & Power buttons are controlled by the PMIC via
the PON hardware, and the Volume Up is connected to a PMIC gpio.
Enable the necessary hardware and setup the GPIO state for the
Volume Up gpio key.
Signed-off-by: Hui Liu <quic_huliu@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240311-gpio-keys-v5-1-08823582f6c9@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
>From what I can tell, the camera buttons are not part of Z2 Tablet
hardware even though other devices based on 'shinano' do have them.
Fixes: ab80661883 ("ARM: dts: qcom: msm8974: Add Sony Xperia Z2 Tablet")
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240306-castor-changes-v1-3-2286eaf85fff@z3ntu.xyz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Clean up some easy things do prepare the dts for further changes.
* Move pinctrl-names below pinctrl-*
* Move status as last property
* Remove default linux,input-type value
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240306-castor-changes-v1-1-2286eaf85fff@z3ntu.xyz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Plug in USB-C related bits and pieces to enable USB role switching and
USB-C orientation handling for the Qualcomm RB1 board.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240304-pm4125-typec-v4-2-f3601a16f9ea@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add node to support the QUP UART6 controller inside of IPQ8074.
Used by some routers to communicate with a Bluetooth controller.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://lore.kernel.org/r/20240229205426.232205-1-frut3k7@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Include the PMIC dedicated file and add regulators to each one of
those 3 eUSB2 repeaters. Tie up the repeaters to their corresponding
USB HS PHY.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240222-x1e80100-dts-smb2360-v3-4-85a691d4f68a@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Include the PMIC dedicated file and add regulators to each one of
those 3 eUSB2 repeaters. Tie up the repeaters to their corresponding
USB HS PHY.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240222-x1e80100-dts-smb2360-v3-3-85a691d4f68a@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The X1E80100 platform implements the v7 SPMI arbiter, which means it
implements two separate buses. The difference, when compared to existing
platforms that also implement v7 SPMI arbiter, is that this is the first
platform that actually has boards with secondary bus populated with some
PMICs. This is why it needs to have 2 separate buses as child nodes of
the arbiter.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240222-x1e80100-dts-smb2360-v3-1-85a691d4f68a@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the definition for the USB-C connector found on this phone and hook
up the relevant bits. This enables USB role switching.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20240220-fp3-typec-v1-1-1930cad81139@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add crypto engine (CE) and CE BAM related nodes and definitions for this
SoC.
For reference:
[ 2.297419] qcrypto 1dfa000.crypto: Crypto device found, version 5.5.1
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20240219-sm6350-qce-v2-1-7acb8838f248@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
This solves the issue when touchpad gets stuck on right or middle
click. This also makes touchpad working smoother.
Signed-off-by: Anton Bambura <jenneron@postmarketos.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240203191200.99185-6-jenneron@postmarketos.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Split keyboard and touchpad pinctrl nodes since they are for different
devices and move keyboard, touchpad and touchscreen pinctrl references to
appropriate nodes.
Signed-off-by: Anton Bambura <jenneron@postmarketos.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240203191200.99185-4-jenneron@postmarketos.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Set names, so they correspond to devices connected to these interfaces.
Signed-off-by: Anton Bambura <jenneron@postmarketos.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240203191200.99185-3-jenneron@postmarketos.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Document the QCM6490 compatible used to describe the pmic glink on this
platform.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20240208-fp5-pmic-glink-v2-1-4837d4abd5a4@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Without explicitly specifying names for the regulators they are named
based on the DeviceTree node name. This results in multiple regulators
with the same name, making debug prints and regulator_summary impossible
to reason about.
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240227-rb3gen2-regulator-names-v1-1-63ceb845dcc8@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Qualcomm X1E80100-CRD board uses shared reset GPIOs for speakers: each
pair out of four speakers share the GPIO. Enable the reset-gpio driver
which handles such case seamlessly.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240227142725.625561-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Each pair of WSA8845 speakers share the powerdown SD_N GPIO, thus this
GPIO is specified twice in each WSA8845 device node. Such DTS was added
hoping non-exclusive GPIO usage would be accepted, but it turned out
otherwise: it is not supported by the Linux kernel.
Linux kernel however supports sharing reset GPIOs, when used bia the
reset controller framework as implemented in commit 26c8a435fc ("ASoC:
dt-bindings: qcom,wsa8840: Add reset-gpios for shared line") and
commit c721f189e8 ("reset: Instantiate reset GPIO controller for
shared reset-gpios").
Convert the property with shutdown GPIO to "reset-gpios" to use
mentioned Linux kernel feature. This allows to bring all four speakers
out of reset.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240227142725.625561-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Correct the SWR1 Soundwire controller port block pack mode to match
reference code. Not sure if this has any impact.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240227142725.625561-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add a node for the Limits Management Hardware to ensure it can be
configured by the operating system.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
[Konrad: add commit msg, rebase]
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240308-topic-rb1_lmh-v2-3-bac3914b0fe3@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Killing the platform with a single write and no firmware involvement is
pretty cool, add support for it.
Note that due to restart notifier priority settings, PSCI reset will
be used instead, unless:
a) PSCI is not exposed by the firmware (e.g. because the fw was replaced)
or
b) PSCI restart fails for some reason
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240307-topic-8280_nodes-v1-3-4eba20e08902@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add usb pd negotiation, but charging is controlled by pm8150b pmic,
so it can only charge battery with 5W,
Signed-off-by: Jianhua Lu <lujianhua000@gmail.com>
Link: https://lore.kernel.org/r/20240302131025.13741-1-lujianhua000@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The DWC PCIe controller can be used with its internal MSI controller or
with an external one such as the GICv3 Interrupt Translation Service
(ITS).
Add the msi-map properties needed to use the GIC ITS. This will also
make Linux switch to the ITS implementation, which allows for assigning
affinity to individual MSIs.
Note that using the GIC ITS on SC8280XP will cause Advanced Error
Reporting (AER) interrupts to be received on errors unlike when using
the internal MSI controller. This will specifically lead to
notifications about Correctable Errors being logged for the Wi-Fi
controller on the Lenovo ThinkPad X13s when ASPM L0s is enabled.
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240306095651.4551-6-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
this fixes an assertion pop in
bch2_check_snapshot_trees() ->
check_snapshot_tree() ->
bch2_snapshot_tree_master_subvol() ->
bch2_snapshot_is_ancestor()
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Nested transaction restart handling is typically best avoided; when the
inner context handles a transaction restart it invalidates the outer
transaction context, so we need to make sure to return a
transaction_restart_nested error.
This code wasn't doing that, and hit the assertion in
for_each_btree_key() that checks for that via trans->restart_count.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
This fixes a deadlock due to using btree_interior_update_worker for non
interior updates - async btree node rewrites were blocking, and then
blocking other interior updates.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
After keys have passed bkey_ops.key_invalid we should never see invalid
extent entry types - but .key_invalid itself needs to cope with them.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
