The HIDP specs define an idle-timeout which automatically disconnects a
device. This has always been implemented in the HIDP layer and forced a
synchronous shutdown of the hidp-scheduler. This works just fine, but
lacks a forced disconnect on the underlying l2cap channels. This has been
broken since:
commit 5205185d46
Author: David Herrmann <dh.herrmann@gmail.com>
Date: Sat Apr 6 20:28:47 2013 +0200
Bluetooth: hidp: remove old session-management
The old session-management always forced an l2cap error on the ctrl/intr
channels when shutting down. The new session-management skips this, as we
don't want to enforce channel policy on the caller. In other words, if
user-space removes an HIDP device, the underlying channels (which are
*owned* and *referenced* by user-space) are still left active. User-space
needs to call shutdown(2) or close(2) to release them.
Unfortunately, this does not work with idle-timeouts. There is no way to
signal user-space that the HIDP layer has been stopped. The API simply
does not support any event-passing except for poll(2). Hence, we restore
old behavior and force EUNATCH on the sockets if the HIDP layer is
disconnected due to idle-timeouts (behavior of explicit disconnects
remains unmodified). User-space can still call
getsockopt(..., SO_ERROR, ...)
..to retrieve the EUNATCH error and clear sk_err. Hence, the channels can
still be re-used (which nobody does so far, though). Therefore, the API
still supports the new behavior, but with this patch it's also compatible
to the old implicit channel shutdown.
Cc: <stable@vger.kernel.org> # 3.10+
Reported-by: Mark Haun <haunma@keteu.org>
Reported-by: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For the Apple Bluetooth devices, read the USB product information and
print them. This allows for easy mapping of chip and USB details.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The calculation for the firmware version number is off by one bit.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For the older controllers like Wilkens Peak and Stone Peak, enabling the
traces requires to switch into manufacturer mode first. This patch does
exactly that, but only for these older controllers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For Intel controllers the diagnostics settings are not persistent over
HCI Reset. So set the quirk to programm them again on every power up.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If the diagnostic settings are not persistent over HCI Reset, then this
quirk can be used to tell the Bluetoth core about it. This will ensure
that the settings are programmed correctly when the controller is
powered up.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The change to bpa10x to use the h4_recv_buf helper added a dependency
on BT_HCIUART. This was incorrectly added to Kconfig by adding a
'select' statement, which now in turn causes build failures
when CONFIG_TTY is not set:
warning: (BT_HCIBPA10X) selects BT_HCIUART which has unmet direct dependencies (NET && BT && TTY)
vers/built-in.o: In function `hci_uart_tty_receive':
fpga-mgr.c:(.text+0x282824): undefined reference to `tty_unthrottle'
drivers/built-in.o: In function `hci_uart_tty_ioctl':
fpga-mgr.c:(.text+0x282aa0): undefined reference to `n_tty_ioctl_helper'
drivers/built-in.o: In function `hci_uart_flush':
This replaces the 'select BT_HCIUART' dependency with 'depends on', which
does not have this kind of problem. Alternatively, one could add 'depends
on TTY', but avoiding 'select' on user-visible options is generally the
preferred choice as that does not introduce the potential for dependency
loops or incomplete dependency chains.
Fixes: 9148991924 ("Bluetooth: bpa10x: Fix missing BT_HCIUART dependency")
Fixes: 943cc59219 ("Bluetooth: bpa10x: Use h4_recv_buf helper for frame reassembly")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The lock states from Intel SfP controllers can only be read once before
loading the firmware. So for debugging purposes, print them out.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There are LE devices on the market that start off by announcing their
public address and then once paired switch to using private address.
To be interoperable with such devices we should simply trust the fact
that we're receiving an IRK from them to indicate that they may use
private addresses in the future. Instead, simply tie the persistency
to the bonding/no-bonding information the same way as for LTKs and
CSRKs.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sending diagnostic messages directly to the monitor socket might cause
issues for devices processing their messages in interrupt context. So
instead of trying to directly forward them, queue them up with the other
HCI packets and lets them be processed by the sockets at the same time.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When using the HCI_CHANNEL_RAW, restrict the packet types to valid ones
from the Bluetooth specification.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The HCI_VENDOR_PKT quirk was needed for BPA-100/105 devices that send
these messages. Now that there is support for proper diagnostic channel
this quirk is no longer needed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For Intel controllers with firmware that allows tracing of baseband
functionality this allows enabling it via set_diag driver callback.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Selecting just BT_HCIUART_H4 is not enough and it also needs to select
BT_HCIUART to avoid this warning:
warning: (BT_HCIBPA10X) selects BT_HCIUART_H4 which has unmet direct
dependencies (NET && BT && BT_HCIUART)
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
ftrace_match parameters are very related and I reduce the number of local
variables & parameters with it.
This is also preparation for module globbing as it would introduce more
realated variables & parameters.
Link: http://lkml.kernel.org/r/1443545176-3215-3-git-send-email-0x7f454c46@gmail.com
Signed-off-by: Dmitry Safonov <0x7f454c46@gmail.com>
[ Made some formatting changes ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
This was introduced with 9e882242c6
which changed the return value of submit_bio_wait() to return != 0 on
error, but didn't update the caller accordingly.
Fixes: 9e882242c6 ("block: Add submit_bio_wait(), remove from md")
Cc: stable@vger.kernel.org (v3.10)
Reported-by: Bill Kuzeja <William.Kuzeja@stratus.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
This was introduced with 9e882242c6
which changed the return value of submit_bio_wait() to return != 0 on
error, but didn't update the caller accordingly.
Fixes: 9e882242c6 ("block: Add submit_bio_wait(), remove from md")
Cc: stable@vger.kernel.org (v3.10)
Reported-by: Bill Kuzeja <William.Kuzeja@stratus.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Perf will core dump if --per-socket/core -a are applied for perf stat.
The root cause is that cpu_map__build_map set refcnt of evlist's cpu_map
to 1. It should set refcnt for the newly created cpu_map, not evlist's
cpu_map.
Here is the example:
# perf stat -e cycles --per-socket -a sleep 1
Performance counter stats for 'system wide':
S0 36 30,196,257 cycles
S1 28 15,823,536 cycles
1.001126828 seconds time elapsed
*** Error in `./perf': corrupted double-linked list: 0x00000000021f9090 ***
======= Backtrace: =========
/lib64/libc.so.6[0x3002e7bbe7]
/lib64/libc.so.6[0x3002e7d2b5]
./perf(perf_evsel__delete+0x28)[0x485bdd]
./perf[0x4800e8]
./perf(perf_evlist__delete+0x5e)[0x482cd5]
./perf(cmd_stat+0xf25)[0x432328]
./perf[0x4768e0]
./perf[0x476ad6]
./perf[0x476b41]
./perf(main+0x1d0)[0x476db2]
/lib64/libc.so.6(__libc_start_main+0xf5)[0x3002e21b45]
./perf[0x4202c5]
Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Link: http://lkml.kernel.org/r/1444388363-35936-1-git-send-email-kan.liang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The format of the role word has changed through the years and the plugin
was never updated; some VMX exit reasons were missing too.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: kvm@vger.kernel.org
Link: http://lkml.kernel.org/r/1443695293-31127-1-git-send-email-pbonzini@redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add all R-Car H3 Clock Pulse Generator Core Clock Outputs, as listed in
Table 8.2a ("List of Clocks [R-Car H3]") of the R-Car Gen3 datasheet
(rev. 0.5E).
Note that internal CPG clocks (S0, S1, S2, S3, SDSRC, SSPSRC, and
RPCSRC) are not included, as they're used as internal clock sources
only.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Michael Turquette <mturquette@baylibre.com>
Reviewed-by: Magnus Damm <damm+renesas@opensource.se>
On Renesas ARM SoCs (SH/R-Mobile, R-Car, RZ), the CPG (Clock Pulse
Generator) and MSSR (Module Standby and Software Reset) blocks are
intimately connected, and share the same register block.
Hence it makes sense to describe these two blocks using a
single device node in DT, instead of using a hierarchical structure with
multiple nodes, using a mix of generic and SoC-specific bindings.
These new DT bindings are intended to replace the existing DT bindings
for CPG core clocks ("renesas,*-cpg-clocks", "renesas,cpg-div6-clock")
and module clocks ("renesas,*-mstp-clocks"), at least for new SoCs.
This will make it easier to add module reset support later, which is
currently not implemented, and difficult to achieve using the existing
bindings due to the intertwined register layout.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Michael Turquette <mturquette@baylibre.com>
Reviewed-by: Magnus Damm <damm+renesas@opensource.se>
Users expect bmap will give allocated block addresses.
Let's play likewise ext4.
Reviewed-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
When discussing the patches to demux ids in rdma_cm instead of ib_cm, it
was decided that it is best to use the P_Key value in the packet headers.
However, the mlx5 and ipath drivers are currently unable to send correct
P_Key values in GMP headers. They always send using a single P_Key that is
set during the GSI QP initialization.
Change the rdma_cm code to look at the P_Key value that is part of the
packet payload as a workaround. Once the drivers are fixed this patch can
be reverted.
Fixes: 4c21b5bcef ("IB/cma: Add net_dev and private data checks to
RDMA CM")
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
c8sectpfe driver selects CONFIG_FW_LOADER_USER_HELPER_FALLBACK by some
reason, but this option is known to be harmful, leading to minutes of
stalls at boot time. The option was intended for only compatibility
for an old exotic system that mandates the udev interaction, and not a
thing a driver selects by itself. Let's remove it.
Fixes: 850a3f7d59 ('[media] c8sectpfe: Add Kconfig and Makefile for the driver')
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Update the copyright year to 2015 in media_api.tmpl.
- Main version number of the spec updated to 4.4.
- Version 3.21 was used for one changelog, this should be 4.1.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert ivtv_yuv_prep_user_dma() to use get_user_pages_unlocked() so
that we don't unnecessarily leak knowledge about mm locking into drivers
code.
CC: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Since commit 5d0360a4f0 it's not possible
anymore to set auto clusters from auto to manual using VIDIOC_S_CTRL.
For example, setting autogain to manual with gspca/ov534 driver and this
sequence of commands does not work:
v4l2-ctl --set-ctrl=gain_automatic=1
v4l2-ctl --list-ctrls | grep gain_automatic
# The following does not work
v4l2-ctl --set-ctrl=gain_automatic=0
v4l2-ctl --list-ctrls | grep gain_automatic
Changing the value using VIDIOC_S_EXT_CTRLS (like qv4l2 does) works
fine.
The apparent cause by looking at the changes in 5d0360a and comparing
with the code path for VIDIOC_S_EXT_CTRLS seems to be that the code in
v4l2-ctrls.c::set_ctrl() is not calling user_to_new() anymore after
calling update_from_auto_cluster(master).
However the root cause of the problem is that calling
update_from_auto_cluster(master) overrides also the _master_ control
state calling cur_to_new() while it was supposed to only update the
volatile controls.
Calling user_to_new() after update_from_auto_cluster(master) was just
masking the original bug by restoring the correct new value of the
master control before making the changes permanent.
Fix the original bug by making update_from_auto_cluster() not override
the new master control value.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Cc: <stable@vger.kernel.org> # for v3.17 and up
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add SDR specific notes to G_MODULATOR / S_MODULATOR documentation.
Signed-off-by: Antti Palosaari <crope@iki.fi>
[hans.verkuil@cisco.com: add quotes in "The term 'modulator'"]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add SDR specific notes to G_TUNER / S_TUNER documentation.
Add V4L2_TUNER_SDR and V4L2_TUNER_RF to supported tuner types to
table.
Signed-off-by: Antti Palosaari <crope@iki.fi>
[hans.verkuil@cisco.com: add quotes in "The term 'tuner'"]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Format names are set by core nowadays. Remove name from driver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
HackRF SDR device has both receiver and transmitter. There is limitation
that receiver and transmitter cannot be used at the same time
(half-duplex operation). That patch implements transmitter support to
existing receiver only driver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
[hans.verkuil@cisco.com: fix krobot unused variable warning]
[hans.verkuil@cisco.com: add back s_modulator from PATCHv4]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Implement single funtion, hackrf_set_params(), which handles all
needed settings. Controls and other IOCTLs are just wrappers to that
function. That way we can get easily better control what we could do
on different device states - sleeping, receiving, transmitting.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There is Avago MGA-81563 amplifier just right after antenna connector.
It could be turned on/off and its gain is around 12dB.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add new modulator type field to documentation.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add type field to that struct like it counterpart v4l2_tuner
already has. We need type field to distinguish different tuner
types from each others for transmitter too.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add new RF tuner gain control named RF Gain. That is aimed for first
amplifier chip right after antenna connector.
There is existing LNA Gain control, which is quite same, but it is
aimed for cases amplifier is integrated to tuner chip. Some designs
have both, as almost all recent tuner silicons has integrated LNA/RF
amplifier in any case.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Allocating a workqueue might fail, which wasn't checked so far and would
lead to NULL ptr derefs when an attempt to use it was made.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
SDR receiver has ADC (Analog-to-Digital Converter) and SDR transmitter
has DAC (Digital-to-Analog Converter). Originally I though it could
be good idea to have own type for receiver and transmitter, but now I
feel one common type for SDR is enough. So lets rename it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: this was added in 4.4, so update 4.2 to 4.4]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The vivid_fb_ioctl() code fails to initialize the 16 _reserved bytes of
struct fb_vblank after the ->hcount member. Add an explicit
memset(0) before filling the structure to avoid the info leak.
Signed-off-by: Salva Peiró <speirofr@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
