Though the tegra-kbc driver should/will continue to support the legacy
"nvidia,wakeup-source" property to enable keyboard as the wakeup source,
we need to add support for the new standard property "wakeup-source".
This patch adds support for "wakeup-source" property in addition to the
existing "nvidia,wakeup-source" property.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The arcnet device has no interrupt to detect if the link has changed
from disconnected to connected. This patch adds an timer to toggle the
link detection. The timer will get retriggered as long as the
reconnection interrupts accure. If the recon interrupts hold off
for >1s we define the connection stable again.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
The EAE PLX-PCI card has special leds on the the main io pci resource
bar. This patch adds support to trigger the conflict and data leds with
the packages.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
The EAE PLX-PCI card has a special rotary encoder
to configure the address of every card individually.
We take this information for the initial setup of
the cards dev_id.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
This patch sets the dev_port according to the index of
the card. This can be used by udev to name the ports
in userspace.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
This patch changes the driver to properly work with the linux netif
interface. The controller gets enabled on open and disabled on close.
Therefor it removes every bogus start of the xceiver. It only gets
enabled on com20020_open and disabled on com20020_close.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
The call for dev_free_skb is done only once. This patch
moves its call to its only user and removes the obsolete
condition variable.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
p_start() and p_stop() are seq_file functions that match. Teach sparse to
know that rcu_read_lock_sched() that is taken by p_start() is released by
p_stop.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When using the Rx clock for both, transmitter and receiver, the
transmitter needs to be set to synchronous with receiver.
This reverts 855675f6e6 ("ASoC: fsl_sai: Set SYNC bit of TCR2 to
Asynchronous Mode"), which, judiging from the commit log, seems to
mixed up between the two synchronous modes: The boolean
sai->synchronous[TX] is indicating wheather the SAI should work in
Rx synchronous mode (sync Tx with Rx), hence if the value is true,
the SYNC field of TCR2 needs to be set to 0x1 ("Synchronous with
receiver").
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Lets fix this obvious coding style issues in the SCO module and bring it
in line with the rest of the Bluetooth subsystem.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There is no point in wrapping hci_sock_dev_event around hci_notify. It
is an empty wrapper which adds no value. So remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The SKB context buffer for HCI request is really not just for requests,
information in their are preserved for the whole HCI layer. So it makes
more sense to actually rename it into bt_cb()->hci and also call it then
struct hci_ctrl.
In addition that allows moving the decoded opcode for outgoing packets
into that struct. So far it was just consuming valuable space from the
main shared items. And opcode are not valid for L2CAP packets.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There are two checks that are still using (MSG_OOB) instead of just
MSG_OOB and so lets just fix them.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Struct of gem object in exynos_drm driver is struct exynos_drm_gem_obj.
It's too long and we can know its meaning of name without _obj postfix.
We use several names to variable name of gem object for exynos_drm -
exynos_gem_obj, gem_obj and obj. Especially "obj" name can cause
misunderstanding with variable name "obj" of struct drm_gem_object.
This will clean about name of gem object for exynos_drm as follows.
s/struct exynos_drm_gem_obj/struct exynos_drm_gem
s/exynos_gem_obj or gem_obj or obj/exynos_gem
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The arm_iommu_detach_device() is a function to detach device of iommu
attached by arm_iommu_attach_device(). The exynos-drm uses
arm_iommu_attach_device() so it should use arm_iommu_detach_device() to
detach device of iommu, not iommu_detach_device().
The drm_release_iommu_mapping() is a function to release mapping of
iommu created by arm_iommu_create_mapping(). It is called by
exynos_drm_unload() so shouldn't be called by drm_iommu_detach_device().
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Set one of the planes for each crtc driver as a cursor plane enabled
window managers to fully work on exynos.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Define DEFAULT_WIN as zero to help set the primary plane on all CRTCs.
Some CRTCs were defining a variable to store the default window, but that
is not necessary as the default (primary) window is always the window zero.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch fixes calling usleep_range() after taking reg_slock
using spin_lock_irqsave(). The mdelay() is used instead.
Waiting in atomic context is not the best idea in general.
Hopefully, waiting occurs only when Video Processor fails
to reset correctly.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Simple formula can be used to calculate CTS and N coefficients.
Additionaly ACR registers have different offsets for different versions
of IP.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Inline function is safer than macro, also the name has been changed to
be consistent with other inline function encoder_to_hdmi.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
hdmi_resources structure was filled by old platform data code and is not
necessary anymore. The patch removes it at groups together resource related
fields in hdmi_context.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The patch converts API to gpiod and moves initialization code
to hdmi_resources_init.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Driver tries to disable sclk_hdmi during re-parenting, to avoid possible
glitches. It is ineffective as the clock is used also by other devices (mixer).
Anyway driver works without disabling sclk_hdmi.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Driver always uses the same number of regulators, so there is no point in
dynamic allocation.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
hdmi-en is an optional regulator so it should be better handled by
devm_regulator_get_optional call.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
DRM device should be destroyed before releasing resources.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Registers are 32-bit, even if only lower 8-bits are used.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Currently driver tries to set specific HDMI-PHY registers in three situations:
- before reset,
- before power off,
- after applying HDMI-PHY configuration.
First two cases seems to be unnecessary - register contents will be lost
anyway. The third case can be merged with HDMI-PHY configuration by fixing
the last byte of configuration data.
The patch has been tested with following platforms:
- exynos4210-universal_c210,
- exynos4412-odroidu3,
- exynos5422-odroidxu3.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The patch moves PLL stabilization check to separate function, adjust timeout
parameters and de-duplicates code common for both HW variants.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Some registers resides at different offsets depending on device version.
This patch adds infrastructure for mapping such registers to proper address
based on hdmi_type. It adds also mappings to some registers.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This compatible was marked as deprecated in Jun 2013 and it is not used since
then. Additionally its driver data points to wrong pll settings, so it
cannot work anyway.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Commit 6894258eda broke drivers that pass NULL as the device pointer
to dma_alloc. The reason is that arch_dma_alloc_attrs() now calls
dma_alloc_coherent_gfp_flags() which in turn calls
dma_alloc_coherent_mask(), where the device pointer is dereferenced
unconditionally.
Fix things by moving the ISA DMA fallback device assignment before the
call to dma_alloc_coherent_gfp_flags().
Fixes: 6894258eda ("dma-mapping: consolidate dma_{alloc,free}_{attrs,coherent}")
Reported-and-tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/1445807503-8920-1-git-send-email-ville.syrjala@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It is useless to start from index 0 when looking for a gate
because only dynamic pipes are retrieved with
ST21NFCA_DM_GETINFO(ST21NFCA_DM_GETINFO_PIPE_LIST).
The first dynamic pipe is present at index 3.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
It is useless to start from index 0 when looking for a gate
because only dynamic pipes are retrieved with
ST_NCI_DM_GETINFO(ST_NCI_DM_GETINFO_PIPE_LIST).
The first dynamic pipe is present at index 3.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NCI_HCI_IDENTITY_MGMT_GATE might be useful to get information
about hardware or firmware version.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When initializing ndev->hci_dev->init_data, only gates field
was set. gate_count needs to be initialized as well.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We need to keep initial st_nci_gates values in order for
nfc_hci_dev_connect_gates to create and open pipe when necessary.
For example after a firmware update CLF pipes are cleared. Changing
pipe values in st21nfca_gates was causing nfc_hci_dev_connect_gates
not using accurate pipes value.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We need to keep initial st_nci_gates values in order for
nci_hci_dev_connect_gates to create and open pipe when necessary.
For example after a firmware update CLF pipes are cleared. Changing
pipe values in st_nci_gates was causing nci_hci_dev_connect_gates
not using accurate pipes value.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFC_HCI_LINK_MGMT_PIPE was never opened in nfc_hci_load_session.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NCI_HCI_LINK_MGMT_PIPE was never opened in st_nci_hci_load_session.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some gates might need to have their pipes explicitly created.
Add a call to nci_hci_create_pipe in nci_hci_connect_gate for
every gate that is different than NCI_HCI_LINK_MGMT_GATE or
NCI_HCI_ADMIN_GATE.
In case of an error when opening a pipe, like in hci layer,
delete the pipe if it was created.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When session_id is filled to 0xff, the pipe configuration is
probably incorrect and needs to be cleared.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
nci_hci_clear_all_pipes might be use full in some cases
for example after a firmware update.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When receiving data in nci_hci_msg_rx_work, extract pipe
value using NCI_HCP_MSG_GET_PIPE macro.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When sending HCI data over NCI, HCI return code is part
of the NCI data. In order to get correctly the HCI return
code, we assume the NCI communication is successful and
extract the return code for the nci_hci functions return code.
This is done because nci_to_errno does not match hci return
code value.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When sending HCI data over NCI, cmd information should be
present only on the first packet.
Each packet shall be specifically allocated and sent to the
NCI layer.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
