When VBUS is not discovered within PD_T_PS_SOURCE_ON although Rp
is detected on CC, TCPM switches the port to SNK_UNATTACHED
state. SNK_UNATTACHED, however does not force TYPEC_CC_OPEN which
makes the partner(source) to think that it is connected.
To overcome this issue, force the port into PORT_RESET state
to make sure the CC lines are open.
Signed-off-by: Badhri Jagan Sridharan <Badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PING messages are used to monitor the connect/disconnect.
However, when PD is carried over CC, so this is not required.
Also, the spec does not clearly say if PD is possible when
Type-c is connected to Type-A/B. So, removing sending
PING messages altogether.
Signed-off-by: Badhri Jagan Sridharan <Badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Once, Rp or Rd is switched, wait for PD_T_CC_DEBOUNCE. If not the
PS_RDY message transmitted might result in failure.
Also, Only wait for PD_T_SRCSWAPSTDBY while in
PR_SWAP_SRC_SNK_TRANSITION_OFF. PD_T_PS_SOURCE_OFF is the overall
time after which the initial sink would issue hard reset.
Signed-off-by: Badhri Jagan Sridharan <Badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the case that the lower layer driver reports a cc change directly
from SINK state to SOURCE state, TCPM doesn't handle these cc change
in SRC_SEND_CAPABILITIES, SRC_READY states. And with SRC_ATTACHED
state, the change is not handled as the port is still considered
connected.
[49606.131672] state change DRP_TOGGLING -> SRC_ATTACH_WAIT
[49606.131701] pending state change SRC_ATTACH_WAIT -> SRC_ATTACHED @
200 ms
[49606.329952] state change SRC_ATTACH_WAIT -> SRC_ATTACHED [delayed 200
ms]
[49606.329978] polarity 0
[49606.329989] Requesting mux mode 1, config 0, polarity 0
[49606.349416] vbus:=1 charge=0
[49606.372274] pending state change SRC_ATTACHED -> SRC_UNATTACHED @ 480
ms
[49606.372431] VBUS on
[49606.372488] state change SRC_ATTACHED -> SRC_STARTUP
...
(the lower layer driver reports a direct change from source to sink)
[49606.536927] pending state change SRC_SEND_CAPABILITIES ->
SRC_SEND_CAPABILITIES @ 150 ms
[49606.547244] CC1: 2 -> 5, CC2: 0 -> 0 [state SRC_SEND_CAPABILITIES,
polarity 0, connected]
This can happen when the lower layer driver and/or the hardware
handles a portion of the Type-C state machine work, and quietly goes
through the unattached state.
Originally-from: Yueyao Zhu <yueyao@google.com>
Signed-off-by: Badhri Jagan Sridharan <Badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While performing PORT_RESET, upon receiving the cc disconnect
signal from the underlaying tcpc device, TCPM transitions into
unattached state. Consider the current type of port while determining
the unattached state.
In the below logs, although the port_type was set to sink, TCPM
transitioned into SRC_UNATTACHED.
[ 762.290654] state change SRC_READY -> PORT_RESET
[ 762.324531] Setting voltage/current limit 0 mV 0 mA
[ 762.327912] polarity 0
[ 762.334864] cc:=0
[ 762.347193] pending state change PORT_RESET -> PORT_RESET_WAIT_OFF @ 100 ms
[ 762.347200] VBUS off
[ 762.347203] CC1: 2 -> 0, CC2: 0 -> 0 [state PORT_RESET, polarity 0, disconnected]
[ 762.347206] state change PORT_RESET -> SRC_UNATTACHED
Signed-off-by: Badhri Jagan Sridharan <Badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the spec:
"4.5.2.2.10.2 Exiting from TryWait.SNK State
The port shall transition to Attached.SNK after tCCDebounce if or when VBUS
is detected. Note the Source may initiate USB PD communications which will
cause brief periods of the SNK.Open state on both the CC1 and CC2 pins,
but this event will not exceed tPDDebounce. The port shall transition to
Unattached.SNK when the state of both of the CC1 and CC2 pins is SNK.Open
for at least tPDDebounce."
Signed-off-by: Badhri Jagan Sridharan <Badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to spec:
" 4.5.2.2.9.2 Exiting from Try.SRC State:
The port shall transition to Attached.SRC when the SRC.Rd
state is detected on exactly one of the CC1 or CC2 pins for
at least tPDDebounce. The port shall transition to
TryWait.SNK after tDRPTry and the SRC.Rd state has not been
detected."
Signed-off-by: Badhri Jagan Sridharan <Badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According the spec, the following is the conditions for exiting Try.SNK
state:
"The port shall wait for tDRPTry and only then begin monitoring the CC1 and
CC2 pins for the SNK.Rp state. The port shall then transition to
Attached.SNK when the SNK.Rp state is detected on exactly one of the CC1
or CC2 pins for at least tPDDebounce and V BUS is detected. Alternatively,
the port shall transition to TryWait.SRC if SNK.Rp state is not detected
for tPDDebounce."
Signed-off-by: Badhri Jagan Sridharan <Badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the spec the following is the condition
for exiting TryWait.SRC:
"The port shall transition to Attached.SRC when V BUS is at vSafe0V
and the SRC.Rd state is detected on exactly one of the CC pins for at
least tCCDebounce. The port shall transition to Unattached.SNK after
tDRPTry if neither of the CC1 or CC2 pins are in the SRC.Rd state"
TCPM at present keeps re-entering the SRC_TRYWAIT and keeps restarting
tDRPTry if the CC presents Rp and disconnects within tCCDebounce.
For example:
[ 447.164308] pending state change SRC_TRYWAIT -> SRC_ATTACHED @ 200 ms
[ 447.164386] CC1: 2 -> 0, CC2: 0 -> 0 [state SRC_TRYWAIT, polarity 0, disconnected]
[ 447.164406] state change SRC_TRYWAIT -> SRC_TRYWAIT
[ 447.164573] cc:=3
[ 447.191408] pending state change SRC_TRYWAIT -> SRC_TRYWAIT_UNATTACHED @ 100 ms
[ 447.191478] CC1: 0 -> 0, CC2: 0 -> 0 [state SRC_TRYWAIT, polarity 0, disconnected]
[ 447.207261] CC1: 0 -> 2, CC2: 0 -> 0 [state SRC_TRYWAIT, polarity 0, connected]
[ 447.207306] state change SRC_TRYWAIT -> SRC_TRYWAIT
[ 447.207485] cc:=3
[ 447.237283] pending state change SRC_TRYWAIT -> SRC_ATTACHED @ 200 ms
[ 447.237357] CC1: 2 -> 0, CC2: 0 -> 0 [state SRC_TRYWAIT, polarity 0, disconnected]
[ 447.237379] state change SRC_TRYWAIT -> SRC_TRYWAIT
[ 447.237532] cc:=3
[ 447.263219] pending state change SRC_TRYWAIT -> SRC_TRYWAIT_UNATTACHED @ 100 ms
[ 447.263289] CC1: 0 -> 0, CC2: 0 -> 0 [state SRC_TRYWAIT, polarity 0, disconnected]
[ 447.280926] CC1: 0 -> 2, CC2: 0 -> 0 [state SRC_TRYWAIT, polarity 0, connected]
[ 447.280970] state change SRC_TRYWAIT -> SRC_TRYWAIT
[ 447.281158] cc:=3
[ 447.307767] pending state change SRC_TRYWAIT -> SRC_ATTACHED @ 200 ms
[ 447.307838] CC1: 2 -> 0, CC2: 0 -> 0 [state SRC_TRYWAIT, polarity 0, disconnected]
[ 447.307858] state change SRC_TRYWAIT -> SRC_TRYWAIT
In TCPM, tDRPTry is set tp 100ms (min 75ms and max 150ms)
and tCCdebounce is set to 200ms (min 100ms and max 200ms).
To overcome the issue, record the time at which the port
enters TryWait.SRC(SRC_TRYWAIT) and re-enter SRC_TRYWAIT
only when CC keeps debouncing within tDRPTry.
Signed-off-by: Badhri Jagan Sridharan <Badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable Try.SRC or Try.SNK only when port_type is
DRP. Try.SRC or Try.SNK state machines are not
valid for SRC only or SNK only ports.
Signed-off-by: Badhri Jagan Sridharan <Badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port type callback call enquires the tcpc_dev if
the requested port type is supported. If supported, then
performs a tcpm reset if required after setting the tcpm
internal port_type variable.
Check against the tcpm port_type instead of checking
against caps.type as port_type reflects the current
configuration.
Signed-off-by: Badhri Jagan Sridharan <Badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we have tty_kopen, we no longer need to export tty_open_by_driver.
This patch makes this function static.
Signed-off-by: Okash Khawaja <okash.khawaja@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces call to tty_open_by_driver with a tty_kopen and
uses tty_kclose instead of tty_release_struct to close it.
Signed-off-by: Okash Khawaja <okash.khawaja@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 12e84c71b7 ("tty: export tty_open_by_driver") exports
tty_open_by_device to allow tty to be opened from inside kernel which
works fine except that it doesn't handle contention with user space or
another kernel-space open of the same tty. For example, opening a tty
from user space while it is kernel opened results in failure and a
kernel log message about mismatch between tty->count and tty's file
open count.
This patch makes kernel access to tty exclusive, so that if a user
process or kernel opens a kernel opened tty, it gets -EBUSY. It does
this by adding TTY_KOPENED flag to tty->flags. When this flag is set,
tty_open_by_driver returns -EBUSY. Instead of overloading
tty_open_by_driver for both kernel and user space, this
patch creates a separate function tty_kopen which closely follows
tty_open_by_driver. tty_kclose closes the tty opened by tty_kopen.
To address the mismatch between tty->count and #fd's, this patch adds
#kopen's to the count before comparing it with tty->count. That way
check_tty_count reflects correct usage count.
Returning -EBUSY on tty open is a change in the interface. I have
tested this with minicom, picocom and commands like "echo foo >
/dev/ttyS0". They all correctly report "Device or resource busy" when
the tty is already kernel opened.
Signed-off-by: Okash Khawaja <okash.khawaja@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make this const as it is only used in a copy operation.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This results in a nice cleanup, and fixes link errors when fbdev support
is disabled.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. Remove module_init()/module_exit() macroes and
visorbus_register_visor_driver/visorbus_unregister_visor_driver
functions.
2. Replace with a short module_driver macro
Signed-off-by: Alex Briskin <br.shurik@gmail.com>
Acked-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"hdr" can't be NULL. We take skb->data which is non-NULL and add an
offset to get "hdr".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove "struct pt_regs *" parameter from interrupt handlers, since
it is no longer passed to interrupt handlers. Also, convert return
types to irqreturn_t.
Additionally, move DIO_irq_handler variable into the setup_GPIO
function, as it's not used outside of this function.
Signed-off-by: Cihangir Akturk <cakturk@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The call to _rtl_dbg_trace via macro HALMAC_RT_TRACE will trigger a null
pointer deference on the null driver_adapter. Fix this by assigning
driver_adapter earlier to halmac_adapter->driver_adapter before the tracing
call so that a non-null driver_adapter is passed instead.
Detected by CoverityScan, CID#1454613 ("Explicit null dereferenced")
Fixes: 938a0447f0 ("staging: r8822be: Add code for halmac sub-driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A memory leak of eeprom_map occurs if the call to halmac_eeprom_parser_88xx
fails. Fix this by kfree'ing it before returning.
Detected by CoverityScan, CID#1454569 ("Resource leak")
Fixes: 938a0447f0 ("staging: r8822be: Add code for halmac sub-driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The obd_init_checks() function can either return -EOVERFLOW or -EINVAL
but we accidentally ignore -EINVAL returns.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The copy_from_user() function returns the number of bytes which we
weren't able to copy. We don't want to return that to the user but
instead we want to return -EFAULT.
Fixes: d7e09d0397 ("staging: add Lustre file system client support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We recently changed from using obd_ioctl_popdata() to calling
copy_to_user() directly. This if statement was supposed to be deleted
but it was over looked. "err" is zero at this point so it means we
return success.
Fixes: b03679f6a4 ("staging: lustre: uapi: remove obd_ioctl_popdata() wrapper")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
calling memcpy immediately after memset with the same region of memory
makes memset redundant.
Build successfully.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The changes in this commit are also being sent to the main rtlwifi
drivers in wireless-next; however, these changes will also be useful for
any debugging of r8822be before it gets moved into the main tree.
Use debugfs to dump register and btcoex status, and also write registers
and h2c.
We create topdir in /sys/kernel/debug/rtlwifi/, and use the MAC address
as subdirectory with several entries to dump mac_reg, bb_reg, rf_reg etc.
An example is
/sys/kernel/debug/rtlwifi/00-11-22-33-44-55-66/mac_0
This change permits examination of device registers in a dynamic manner,
a feature not available with the current debug mechanism.
We use seq_file to replace RT_TRACE to dump status, then we can use 'cat'
to access btcoex's status through debugfs.
(i.e. /sys/kernel/debug/rtlwifi/00-11-22-33-44-55-66/btcoex)
Other related changes are
1. implement btc_disp_dbg_msg() to access btcoex's common status.
2. remove obsolete field bt_exist
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Smatch is distrustful of the "capab" value and marks it as user
controlled. I think it actually comes from the firmware? Anyway, I
looked at other drivers and they added a bounds check and it seems like
a harmless thing to have so I have added it here as well.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is created to solve the following coding style issue reported
by the checkpatch script.
CHECK: spaces preffered around that '&' (ctx:VxV)
Signed-off-by: Janani Sankara Babu <jananis37@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch solves the following warning shown by the checkpatch script
WARNING: Comparisons should place the constants on the right side of
the test
Signed-off-by: Janani Sankara Babu <jananis37@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Another fix, this time in common IOMMU sysfs code
- In the conversion from the old iommu sysfs-code to the
iommu_device_register interface, I missed to update the
release path for the struct device associated with an IOMMU.
It freed the 'struct device', which was a pointer before, but
is now embedded in another struct. Freeing from the middle of
allocated memory had all kinds of nasty side effects when an
IOMMU was unplugged. Unfortunatly nobody unplugged and IOMMU
until now, so this was not discovered earlier. The fix is to
make the 'struct device' a pointer again.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJZor4gAAoJECvwRC2XARrj3CUP/3/rhNhHfuvq0C+Nz+ikzZSg
xavSSbZztC3SQnr9bgky5TP8Djf9zXzD6DiEGhJoOr98K7R/nvFyaR1NfYnIwHi3
ofngfOcEuuNzInO9L0huHlkqlbUxEwcWTi/QbrFm+W2iL6vOgYejlspFLXAPviDo
BlSzJTHzeyXJPZqKDuKB2oO+fVk/xor7KEelsh5fsRrBwFl/JclH5SwIusv4ORfJ
sY+02Z8MfLx5+NUvSDj/APoGOlYn0T+XipvduIp2wDtQBmDvN332KWqB1JnAKVdM
j27l0BnHABbe5TjQMzj3opAl2v2ZsUqRzolfJdvrh8Gr3gLT1LyMn8A3CRzelBDI
jzNsPp9BG2z8enUrppy6yZwv95uxEvNrwrc7jmX46UK12Gf7eBlNGLSe4u+5Ctj5
5e6Eui5y5g/4/DW+BbXt+DjYZHwqJdC1+KAI9XR6sMPRweEmdLhclqgtYhTjGGX9
w2swhpWjcZ7bte8EF/Mlg2Dl6//WTcqFBeyZbHe+HwzWP33EIXpHdfwJCtWpfD/+
lvdDvI2DUrDUiMVcJwnYrWbRuHtdE/fjI0BtmYA01JL0Oe4+kxB3vS4MnlmH8ENc
i7KThAEDdyrqeX1DTPmef1YTuhprGAB/pj2GYGe/93QDXMDOPMG3pvYm6Up02MzD
a2UNL/JvCEQloABXFyIM
=/lXQ
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v4.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fix from Joerg Roedel:
"Another fix, this time in common IOMMU sysfs code.
In the conversion from the old iommu sysfs-code to the
iommu_device_register interface, I missed to update the release path
for the struct device associated with an IOMMU. It freed the 'struct
device', which was a pointer before, but is now embedded in another
struct.
Freeing from the middle of allocated memory had all kinds of nasty
side effects when an IOMMU was unplugged. Unfortunatly nobody
unplugged and IOMMU until now, so this was not discovered earlier. The
fix is to make the 'struct device' a pointer again"
* tag 'iommu-fixes-v4.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu: Fix wrong freeing of iommu_device->dev
Here is a single misc driver fix for 4.13-rc7. It resolves a reported
problem in the Android binder driver due to previous patches in 4.13-rc.
It's been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWaJyTQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk3GgCgi/suT2Mqfun8Ohmz9i4fMwjJ7UwAn2s3XxeH
3b+zwqeZD1+zB/w6hZ2v
=9B01
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fix from Greg KH:
"Here is a single misc driver fix for 4.13-rc7. It resolves a reported
problem in the Android binder driver due to previous patches in
4.13-rc.
It's been in linux-next with no reported issues"
* tag 'char-misc-4.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
ANDROID: binder: fix proc->tsk check.
Here are few small staging driver fixes, and some more IIO driver fixes
for 4.13-rc7. Nothing major, just resolutions for some reported
problems.
All of these have been in linux-next with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWaJy4A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynWcACgxpL4f0LeykFayPprtrciey5OOGoAnAhfG7Lq
LCuaIj8AtUVfwoWXVwBA
=RSsO
-----END PGP SIGNATURE-----
Merge tag 'staging-4.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/iio fixes from Greg KH:
"Here are few small staging driver fixes, and some more IIO driver
fixes for 4.13-rc7. Nothing major, just resolutions for some reported
problems.
All of these have been in linux-next with no reported problems"
* tag 'staging-4.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
iio: magnetometer: st_magn: remove ihl property for LSM303AGR
iio: magnetometer: st_magn: fix status register address for LSM303AGR
iio: hid-sensor-trigger: Fix the race with user space powering up sensors
iio: trigger: stm32-timer: fix get trigger mode
iio: imu: adis16480: Fix acceleration scale factor for adis16480
PATCH] iio: Fix some documentation warnings
staging: rtl8188eu: add RNX-N150NUB support
Revert "staging: fsl-mc: be consistent when checking strcmp() return"
iio: adc: stm32: fix common clock rate
iio: adc: ina219: Avoid underflow for sleeping time
iio: trigger: stm32-timer: add enable attribute
iio: trigger: stm32-timer: fix get/set down count direction
iio: trigger: stm32-timer: fix write_raw return value
iio: trigger: stm32-timer: fix quadrature mode get routine
iio: bmp280: properly initialize device for humidity reading
transport, improperly bringing down the link if SPADs are corrupted, and
an out-of-order issue regarding link negotiation and data passing.
-----BEGIN PGP SIGNATURE-----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=qmzC
-----END PGP SIGNATURE-----
Merge tag 'ntb-4.13-bugfixes' of git://github.com/jonmason/ntb
Pull NTB fixes from Jon Mason:
"NTB bug fixes to address an incorrect ntb_mw_count reference in the
NTB transport, improperly bringing down the link if SPADs are
corrupted, and an out-of-order issue regarding link negotiation and
data passing"
* tag 'ntb-4.13-bugfixes' of git://github.com/jonmason/ntb:
ntb: ntb_test: ensure the link is up before trying to configure the mws
ntb: transport shouldn't disable link due to bogus values in SPADs
ntb: use correct mw_count function in ntb_tool and ntb_transport
Kfree on NULL pointer is a no-op and therefore checking is redundant.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
call to memset to assign 0 value immediately after allocating
memory with kzalloc is unnecesaary as kzalloc allocates the memory
filled with 0 value.
Build and tested it.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register with module_driver macro instead of module_init/module_exit.
Signed-off-by: Alex Briskin <br.shurik@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull input fixes from Dmitry Torokhov:
- a tweak to the IBM Trackpoint driver that helps recognizing
trackpoints on never Lenovo Carbons
- a fix to the ALPS driver solving scroll issues on some Dells
- yet another ACPI ID has been added to Elan I2C toucpad driver
- quieted diagnostic message in soc_button_array driver
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ALPS - fix two-finger scroll breakage in right side on ALPS touchpad
Input: soc_button_array - silence -ENOENT error on Dell XPS13 9365
Input: trackpoint - add new trackpoint firmware ID
Input: elan_i2c - add ELAN0602 ACPI ID to support Lenovo Yoga310
Fixes two obvious bugs in virtio pci.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZoG+uAAoJECgfDbjSjVRpvAMIAIoONNPd53SPKDVuyU1ycz7H
hRVJ9dgVqsCyJV7UQNXznTkk1Te+todM3eBOnnWGxBUPyyjjn+nRJY8ObzvPZNtr
GZjBHhuCeWAi1HPcGk3VKFCXB9yzVc7x91YoSZRWRveB1hOoqWCNccuXMlOf1mLC
AAYMdBR7JH9CTA5v73z0n4XmfDPFja9g5qhv3JxYypzS3IrWglsVV8RFFG94zJys
qsg3Ys6SdYnC4whdtT0sdj6zcVV3STqLtutUcWzpBJiPwL+TYprOtGxhjhjG/YdP
vurTYmMk1FZyTlxflfzH0yIRQVZyxARcPGrchhvFv9eE4qN0y4E72FkN8UyyKpU=
=qTWW
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio fixes from Michael Tsirkin:
"Fixes two obvious bugs in virtio pci"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_pci: fix cpu affinity support
virtio_blk: fix incorrect message when disk is resized
Two fixes - one for a 4.13 regression, and the other for an older one:
* Atmel NAND: since we started utilizing ONFI timings, we found that we
were being too restrict at rejecting them, partly due to discrepancies
in ONFI 4.0 and earlier versions. Relax the restriction to keep these
platforms booting. This is a 4.13-rc1 regression.
* nandsim: repeated probe/removal may not work after a failed init,
because we didn't free up our debugfs files properly on the failure
path. This has been around since 3.8, but it's nice to get this fixed
now in a nice easy patch that can target -stable, since there's
already refactoring work (that also fixes the issue) targeted for the
next merge window
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=yDqO
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20170825' of git://git.infradead.org/linux-mtd
Pull MTD fixes from Brian Norris:
"Two fixes - one for a 4.13 regression, and the other for an older one:
- Atmel NAND: since we started utilizing ONFI timings, we found that
we were being too restrict at rejecting them, partly due to
discrepancies in ONFI 4.0 and earlier versions. Relax the
restriction to keep these platforms booting. This is a 4.13-rc1
regression.
- nandsim: repeated probe/removal may not work after a failed init,
because we didn't free up our debugfs files properly on the failure
path. This has been around since 3.8, but it's nice to get this
fixed now in a nice easy patch that can target -stable, since
there's already refactoring work (that also fixes the issue)
targeted for the next merge window"
* tag 'for-linus-20170825' of git://git.infradead.org/linux-mtd:
mtd: nand: atmel: Relax tADL_min constraint
mtd: nandsim: remove debugfs entries in error path
Pull block fixes from Jens Axboe:
"A small batch of fixes that should be included for the 4.13 release.
This contains:
- Revert of the 4k loop blocksize support. Even with a recent batch
of 4 fixes, we're still not really happy with it. Rather than be
stuck with an API issue, let's revert it and get it right for 4.14.
- Trivial patch from Bart, adding a few flags to the blk-mq debugfs
exports that were added in this release, but not to the debugfs
parts.
- Regression fix for bsg, fixing a potential kernel panic. From
Benjamin.
- Tweak for the blk throttling, improving how we account discards.
From Shaohua"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq-debugfs: Add names for recently added flags
bsg-lib: fix kernel panic resulting from missing allocation of reply-buffer
Revert "loop: support 4k physical blocksize"
blk-throttle: cap discard request size
Pull i2c fixes from Wolfram Sang:
"I2C has some bugfixes for you: mainly Jarkko fixed up a few things in
the designware driver regarding the new slave mode. But Ulf also fixed
a long-standing and now agreed suspend problem. Plus, some simple
stuff which nonetheless needs fixing"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: designware: Fix runtime PM for I2C slave mode
i2c: designware: Remove needless pm_runtime_put_noidle() call
i2c: aspeed: fixed potential null pointer dereference
i2c: simtec: use release_mem_region instead of release_resource
i2c: core: Make comment about I2C table requirement to reflect the code
i2c: designware: Fix standard mode speed when configuring the slave mode
i2c: designware: Fix oops from i2c_dw_irq_handler_slave
i2c: designware: Fix system suspend
irq_create_affinity_masks() can return NULL on non-SMP systems, when there
are not enough "free" vectors available to spread, or if memory allocation
for the CPU masks fails. Only the allocation failure is of interest, and
even then the system will work just fine except for non-optimally spread
vectors. Thus remove the warnings.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
A single fix for tegra210-adma driver to check of_irq_get() error
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ccQ+
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-fix-4.13-rc7' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fix from Vinod Koul:
"A single fix for tegra210-adma driver to check of_irq_get() error"
* tag 'dmaengine-fix-4.13-rc7' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: tegra210-adma: fix of_irq_get() error check
-----BEGIN PGP SIGNATURE-----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=kkM0
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-for-v4.13-rc7' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Fixes for rc7, nothing too crazy, some core, i915, and sunxi fixes,
Intel CI has been responsible for some of these fixes being required"
* tag 'drm-fixes-for-v4.13-rc7' of git://people.freedesktop.org/~airlied/linux:
drm/i915/gvt: Fix the kernel null pointer error
drm: Release driver tracking before making the object available again
drm/i915: Clear lost context-switch interrupts across reset
drm/i915/bxt: use NULL for GPIO connection ID
drm/i915/cnl: Fix LSPCON support.
drm/i915/vbt: ignore extraneous child devices for a port
drm/i915: Initialize 'data' in intel_dsi_dcs_backlight.c
drm/atomic: If the atomic check fails, return its value first
drm/atomic: Handle -EDEADLK with out-fences correctly
drm: Fix framebuffer leak
drm/imx: ipuv3-plane: fix YUV framebuffer scanout on the base plane
gpu: ipu-v3: add DRM dependency
drm/rockchip: Fix suspend crash when drm is not bound
drm/sun4i: Implement drm_driver lastclose to restore fbdev console
Commit 0b0f9dc5 ("Revert "virtio_pci: use shared interrupts for
virtqueues"") removed the adjustment of the pre_vectors for the virtio
MSI-X vector allocation which was added in commit fb5e31d9 ("virtio:
allow drivers to request IRQ affinity when creating VQs"). This will
lead to an incorrect assignment of MSI-X vectors, and potential
deadlocks when offlining cpus.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fixes: 0b0f9dc5 ("Revert "virtio_pci: use shared interrupts for virtqueues")
Reported-by: YASUAKI ISHIMATSU <yasu.isimatu@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>