We are about to re-use those for the exec_op() implementation which
will not rely on au1550_hwcontrol(). Let's patch those helpers to
simply use the iomem address stored in the context.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200419193037.1544035-2-boris.brezillon@collabora.com
The Denali IP have several registers to specify how many clock cycles
should be waited between falling/rising signals. You can improve the
NAND access performance by programming these registers with optimized
values.
Because struct nand_sdr_timings represents the device requirement
in pico seconds, denali_setup_data_interface() computes the register
values by dividing the device timings with the clock period.
Marek Vasut reported this driver in the latest kernel does not work
on his SOCFPGA board. (The on-board NAND chip is mode 5)
The suspicious parameter is acc_clks, so this commit relaxes it.
The Denali NAND Flash Memory Controller User's Guide describes this
register as follows:
acc_clks
signifies the number of bus interface clk_x clock cycles,
controller should wait from read enable going low to sending
out a strobe of clk_x for capturing of incoming data.
Currently, acc_clks is calculated only based on tREA, the delay on the
chip side. This does not include additional delays that come from the
data path on the PCB and in the SoC, load capacity of the pins, etc.
This relatively becomes a big factor on faster timing modes like mode 5.
Before supporting the ->setup_data_interface() hook (e.g. Linux 4.12),
the Denali driver hacks acc_clks in a couple of ways [1] [2] to support
the timing mode 5.
We would not go back to the hard-coded acc_clks, but we need to include
this factor into the delay somehow. Let's say the amount of the additional
delay is 10000 pico sec.
In the new calculation, acc_clks is determined by timings->tREA_max +
data_setup_on_host.
Also, prolong the RE# low period to make sure the data hold is met.
Finally, re-center the data latch timing for extra safety.
[1] https://github.com/torvalds/linux/blob/v4.12/drivers/mtd/nand/denali.c#L276
[2] https://github.com/torvalds/linux/blob/v4.12/drivers/mtd/nand/denali.c#L282
Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200317071821.9916-1-yamada.masahiro@socionext.com
->exec_op() is passed a check_only argument that encodes when the
controller should just check whether the operation is supported or not
without executing it. Some controllers simply ignore this arguments,
others don't but keep modifying some of the registers before returning.
Let's fix all those drivers.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200418194217.1016060-1-boris.brezillon@collabora.com
Remove including <linux/version.h> that don't need it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200417101129.35556-1-yuehaibing@huawei.com
Fix sparse warning:
drivers/mtd/nand/raw/cadence-nand-controller.c:2595:5:
warning: symbol 'cadence_nand_attach_chip' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200410115228.30440-1-yuehaibing@huawei.com
Fix sparse warning:
drivers/mtd/nand/raw/ingenic/ingenic_nand_drv.c:105:32:
warning: symbol 'qi_lb60_ooblayout_ops' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200410115121.11852-1-yuehaibing@huawei.com
No need to use expensive atomic change_bit() on dat[] and err_idx[]:
1. fsmc_bch8_correct_data() is called while mutex chip->lock is held
2. err_idx[] is a local variable.
To avoid big endian concern due to type cast to unsigned long, directly
change the bit in the specified byte instead of using non-atomic
__change_bit().
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1576886755-9788-1-git-send-email-fenghua.yu@intel.com
- Ensure that direct mapping alias is always flushed when changing page
attributes. The optimization for small ranges failed to do so when
the virtual address was in the vmalloc or module space.
- Unbreak the trace event registration for syscalls without arguments
caused by the refactoring of the SYSCALL_DEFINE0() macro.
- Move the printk in the TSC deadline timer code to a place where it is
guaranteed to only be called once during boot and cannot be rearmed by
clearing warn_once after boot. If it's invoked post boot then lockdep
rightfully complains about a potential deadlock as the calling context
is different.
- A series of fixes for objtool and the ORC unwinder addressing variety
of small issues:
Stack offset tracking for indirect CFAs in objtool ignored subsequent
pushs and pops
Repair the unwind hints in the register clearing entry ASM code
Make the unwinding in the low level exit to usermode code stop after
switching to the trampoline stack. The unwind hint is not longer valid
and the ORC unwinder emits a warning as it can't find the registers
anymore.
Fix the unwind hints in switch_to_asm() and rewind_stack_do_exit()
which caused objtool to generate bogus ORC data.
Prevent unwinder warnings when dumping the stack of a non-current
task as there is no way to be sure about the validity because the
dumped stack can be a moving target.
Make the ORC unwinder behave the same way as the frame pointer
unwinder when dumping an inactive tasks stack and do not skip the
first frame.
Prevent ORC unwinding before ORC data has been initialized
Immediately terminate unwinding when a unknown ORC entry type is
found.
Prevent premature stop of the unwinder caused by IRET frames.
Fix another infinite loop in objtool caused by a negative offset which
was not catched.
Address a few build warnings in the ORC unwinder and add missing
static/ro_after_init annotations
-----BEGIN PGP SIGNATURE-----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=0rCi
-----END PGP SIGNATURE-----
Merge tag 'x86-urgent-2020-05-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of fixes for x86:
- Ensure that direct mapping alias is always flushed when changing
page attributes. The optimization for small ranges failed to do so
when the virtual address was in the vmalloc or module space.
- Unbreak the trace event registration for syscalls without arguments
caused by the refactoring of the SYSCALL_DEFINE0() macro.
- Move the printk in the TSC deadline timer code to a place where it
is guaranteed to only be called once during boot and cannot be
rearmed by clearing warn_once after boot. If it's invoked post boot
then lockdep rightfully complains about a potential deadlock as the
calling context is different.
- A series of fixes for objtool and the ORC unwinder addressing
variety of small issues:
- Stack offset tracking for indirect CFAs in objtool ignored
subsequent pushs and pops
- Repair the unwind hints in the register clearing entry ASM code
- Make the unwinding in the low level exit to usermode code stop
after switching to the trampoline stack. The unwind hint is no
longer valid and the ORC unwinder emits a warning as it can't
find the registers anymore.
- Fix unwind hints in switch_to_asm() and rewind_stack_do_exit()
which caused objtool to generate bogus ORC data.
- Prevent unwinder warnings when dumping the stack of a
non-current task as there is no way to be sure about the
validity because the dumped stack can be a moving target.
- Make the ORC unwinder behave the same way as the frame pointer
unwinder when dumping an inactive tasks stack and do not skip
the first frame.
- Prevent ORC unwinding before ORC data has been initialized
- Immediately terminate unwinding when a unknown ORC entry type
is found.
- Prevent premature stop of the unwinder caused by IRET frames.
- Fix another infinite loop in objtool caused by a negative
offset which was not catched.
- Address a few build warnings in the ORC unwinder and add
missing static/ro_after_init annotations"
* tag 'x86-urgent-2020-05-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/unwind/orc: Move ORC sorting variables under !CONFIG_MODULES
x86/apic: Move TSC deadline timer debug printk
ftrace/x86: Fix trace event registration for syscalls without arguments
x86/mm/cpa: Flush direct map alias during cpa
objtool: Fix infinite loop in for_offset_range()
x86/unwind/orc: Fix premature unwind stoppage due to IRET frames
x86/unwind/orc: Fix error path for bad ORC entry type
x86/unwind/orc: Prevent unwinding before ORC initialization
x86/unwind/orc: Don't skip the first frame for inactive tasks
x86/unwind: Prevent false warnings for non-current tasks
x86/unwind/orc: Convert global variables to static
x86/entry/64: Fix unwind hints in rewind_stack_do_exit()
x86/entry/64: Fix unwind hints in __switch_to_asm()
x86/entry/64: Fix unwind hints in kernel exit path
x86/entry/64: Fix unwind hints in register clearing code
objtool: Fix stack offset tracking for indirect CFAs
search which can be triggered when building the kernel with
-ffunction-sections.
-----BEGIN PGP SIGNATURE-----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=0+2v
-----END PGP SIGNATURE-----
Merge tag 'objtool-urgent-2020-05-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull objtool fix from Thomas Gleixner:
"A single fix for objtool to prevent an infinite loop in the
jump table search which can be triggered when building the
kernel with '-ffunction-sections'"
* tag 'objtool-urgent-2020-05-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Fix infinite loop in find_jump_table()
With those changes GCC9 fails to analyze arch_futex_atomic_op_inuser()
correctly and emits a 'maybe unitialized' warning. While we usually ignore
compiler stupidity the conditional store is pointless anyway because the
correct case has to store. For the fault case the extra store does no harm.
-----BEGIN PGP SIGNATURE-----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=Va5K
-----END PGP SIGNATURE-----
Merge tag 'locking-urgent-2020-05-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fix from Thomas Gleixner:
"A single fix for the fallout of the recent futex uacess rework.
With those changes GCC9 fails to analyze arch_futex_atomic_op_inuser()
correctly and emits a 'maybe unitialized' warning. While we usually
ignore compiler stupidity the conditional store is pointless anyway
because the correct case has to store. For the fault case the extra
store does no harm"
* tag 'locking-urgent-2020-05-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ARM: futex: Address build warning
Including:
- The race condition fixes for the AMD IOMMU driver. This are 5
patches fixing two race conditions around
increase_address_space(). The first race condition was around
the non-atomic update of the domain page-table root pointer
and the variable containing the page-table depth (called
mode). This is fixed now be merging page-table root and mode
into one 64-bit field which is read/written atomically.
The second race condition was around updating the page-table
root pointer and making it public before the hardware caches
were flushed. This could cause addresses to be mapped and
returned to drivers which are not reachable by IOMMU hardware
yet, causing IO page-faults. This is fixed too by adding the
necessary flushes before a new page-table root is published.
Related to the race condition fixes these patches also add a
missing domain_flush_complete() barrier to update_domain() and
a fix to bail out of the loop which tries to increase the
address space when the call to increase_address_space() fails.
Qian was able to trigger the race conditions under high load
and memory pressure within a few days of testing. He confirmed
that he has seen no issues anymore with the fixes included
here.
- Fix for a list-handling bug in the VirtIO IOMMU driver.
-----BEGIN PGP SIGNATURE-----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=gqwr
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v5.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
- Race condition fixes for the AMD IOMMU driver.
These are five patches fixing two race conditions around
increase_address_space(). The first race condition was around the
non-atomic update of the domain page-table root pointer and the
variable containing the page-table depth (called mode). This is fixed
now be merging page-table root and mode into one 64-bit field which
is read/written atomically.
The second race condition was around updating the page-table root
pointer and making it public before the hardware caches were flushed.
This could cause addresses to be mapped and returned to drivers which
are not reachable by IOMMU hardware yet, causing IO page-faults. This
is fixed too by adding the necessary flushes before a new page-table
root is published.
Related to the race condition fixes these patches also add a missing
domain_flush_complete() barrier to update_domain() and a fix to bail
out of the loop which tries to increase the address space when the
call to increase_address_space() fails.
Qian was able to trigger the race conditions under high load and
memory pressure within a few days of testing. He confirmed that he
has seen no issues anymore with the fixes included here.
- Fix for a list-handling bug in the VirtIO IOMMU driver.
* tag 'iommu-fixes-v5.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/virtio: Reverse arguments to list_add
iommu/amd: Do not flush Device Table in iommu_map_page()
iommu/amd: Update Device Table in increase_address_space()
iommu/amd: Call domain_flush_complete() in update_domain()
iommu/amd: Do not loop forever when trying to increase address space
iommu/amd: Fix race in increase_address_space()/fetch_pte()
There is a soft dependency against dsa_loop_bdinfo.ko which sets up the
MDIO device registration, since there are no symbols referenced by
dsa_loop.ko, there is no automatic loading of dsa_loop_bdinfo.ko which
is needed.
Fixes: 98cd1552ea ("net: dsa: Mock-up driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=73nU
-----END PGP SIGNATURE-----
Merge tag 'block-5.7-2020-05-09' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- a small series fixing a use-after-free of bdi name (Christoph,Yufen)
- NVMe fix for a regression with the smaller CQ update (Alexey)
- NVMe fix for a hang at namespace scanning error recovery (Sagi)
- fix race with blk-iocost iocg->abs_vdebt updates (Tejun)
* tag 'block-5.7-2020-05-09' of git://git.kernel.dk/linux-block:
nvme: fix possible hang when ns scanning fails during error recovery
nvme-pci: fix "slimmer CQ head update"
bdi: add a ->dev_name field to struct backing_dev_info
bdi: use bdi_dev_name() to get device name
bdi: move bdi_dev_name out of line
vboxsf: don't use the source name in the bdi name
iocost: protect iocg->abs_vdebt with iocg->waitq.lock
The variable status is being initializeed with a value that is never read
and it is being updated later with a new value. The initialization
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The variable ret is being initializeed with a value that is never read
and it is being updated later with a new value. The initialization
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The variable ret is being initializeed with a value that is never read
and it is being updated later with a new value. The initialization
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The framework is unhappy about them, because it uses the names in sysfs
attributes:
power_supply olpc-ac: hwmon: 'olpc-ac' is not a valid name attribute, please fix
power_supply olpc-battery: hwmon: 'olpc-battery' is not a valid name attribute, please fix
See also commit 648cd48c9e ("hwmon: Do not accept invalid name
attributes") and commit 74d3b64197 ("hwmon: Relax name attribute
validation for new APIs").
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This delay-fix is picked up from downstream driver,
we measured that 25 - 35 ms delay ensure that we get required data.
Tested on SMB347 on Nexus 7 2012. Otherwise IRQSTAT_E fails to provide
correct information.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix failure when USB cable is connected:
smb347 2-006a: reading IRQSTAT_D failed
Fixes: 1502cfe19b ("smb347-charger: Fix battery status reporting logic for charger faults")
Tested-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There is a repeated pattern in multiple drivers where they want to switch
the bandwidth between zero and some other value. This is happening often
in the suspend/resume callbacks. Let's add helper functions to enable and
disable the path, so that callers don't have to take care of remembering
the bandwidth values and handle this in the framework instead.
With this patch the users can call icc_disable() and icc_enable() to lower
their bandwidth request to zero and then restore it back to it's previous
value.
Suggested-by: Evan Green <evgreen@chromium.org>
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20200507120846.8354-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
In case of error, the function of_parse_phandle() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: f0d8048525 ("interconnect: Add imx core driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Link: https://lore.kernel.org/r/20200509030214.14435-1-weiyongjun1@huawei.com
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Fireface UFX was shipped by RME GmbH in 2010, and now discontinued.
Although this model has some enhanced feature which Fireface 802
doesn't have (e.g. on-board USB mass storage device class, configuration
interface with color display), the functionality relevant to
packet communication on IEEE 1394 bus seems to be the same as
Fireface 802 (e.g. available number of channels for PCM frame in
each sampling transfer frequency).
With the assumption, this commit adds support for Fireface UFX. In ALSA
fireface driver, these two models are handled as the same one.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20200510074301.116224-7-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fireface 802 was shipped by RME GmbH in 2014. This model supports later
protocol for management of isochronous communication and synchronization
of sampling transmission frequency.
This model consists of below ICs:
* TI TSB41AB2
* Xilinx Spartan-6 FPGA XC6SLX16
* TI TMS320 C6747
* SMSC USB3250
Especially, this model just supports IEEE 1394a, against its name which
evokes Fireface 800.
This commit adds support for Fireface 802 (tested). Userspace applications
can transfer PCM frames and MIDI messages via ALSA PCM/Rawmidi interface.
I note that 4 channels for ADAt1 and ADAT2 are disabled at higher sampling
transfer frequency since isochronous resources reservation fails due to
bandwidth limitation of IEEE 1394a.
The value read from LATTER_SYNC_STATUS register is slightly different
from the one of Fireface UCX. The higher 4 bits and lower 4 bits are
swapped within the same byte.
Without any assist of userspace application, transmitted MIDI messages
from the device are not going to be processed. For detail, please refer
to my comment in code of latter protocol.
$ python crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 0404ffff bus_info_length 4, crc_length 4, crc 65535 (should be 26805)
404 31333934 bus_name "1394"
408 20008000 irmc 0, cmc 0, isc 1, bmc 0, cyc_clk_acc 0, max_rec 8 (512)
40c 000a3504 company_id 000a35 |
410 38077423 device_id 0438077423 | EUI-64 000a350438077423
root directory
-----------------------------------------------------------------
414 0005ffff directory_length 5, crc 65535 (should be 9514)
418 0c0083c0 node capabilities per IEEE 1394
41c 03000a35 vendor
420 8100000b --> descriptor leaf at 44c
424 8d000007 --> eui-64 leaf at 440
428 d1000001 --> unit directory at 42c
unit directory at 42c
-----------------------------------------------------------------
42c 0004ffff directory_length 4, crc 65535 (should be 45134)
430 12000a35 specifier id
434 13000005 version
438 17101800 model
43c 81000008 --> descriptor leaf at 45c
eui-64 leaf at 440
-----------------------------------------------------------------
440 0002ffff leaf_length 2, crc 65535 (should be 60131)
444 000a3504 company_id 000a35 |
448 38077423 device_id 0438077423 | EUI-64 000a350438077423
descriptor leaf at 44c
-----------------------------------------------------------------
44c 0003ffff leaf_length 3, crc 65535 (should be 469)
450 00000000 textual descriptor
454 00000000 minimal ASCII
458 524d4521 "RME!"
descriptor leaf at 45c
-----------------------------------------------------------------
45c 0005ffff leaf_length 5, crc 65535 (should be 10561)
460 00000000 textual descriptor
464 00000000 minimal ASCII
468 46697265 "Fire"
46c 66616365 "face"
470 20383032 " 802"
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20200510074301.116224-6-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In RME fireface series, version field of unit directory in configuration
ROM is used to distinguish each model. The value of field is known and
it's better to use enumeration constants for code representation.
This commit adds enumeration constants for model identification.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20200510074301.116224-4-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the latter models of RME Fireface series, device start to transfer
packets several dozens of milliseconds. On the other hand, ALSA fireface
driver starts IR context 2 milliseconds after the start. This results
in loss to handle incoming packets on the context.
This commit changes to start IR context immediately instead of
postponement. For Fireface 800, this affects nothing because the device
transfer packets 100 milliseconds or so after the start and this is
within wait timeout.
Cc: <stable@vger.kernel.org>
Fixes: acfedcbe1c ("ALSA: firewire-lib: postpone to start IR context")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20200510074301.116224-3-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
128000 and 192000 are congruence modulo 32000, thus it's wrong to
distinguish them as multiple of 32000 and 48000 by modulo 32000 at
first.
Additionally, used condition statement to detect quadruple speed can
cause missing bit flag.
Furthermore, counter to ensure the configuration is wrong and it
causes false positive.
This commit fixes the above three bugs.
Cc: <stable@vger.kernel.org>
Fixes: 60aec494b3 ("ALSA: fireface: support allocate_resources operation in latter protocol")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20200510074301.116224-2-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This looks really unusual to have a 'get_device()' hidden in a 'dev_err()'
call.
Remove it.
While at it add a missing \n at the end of the message.
Fixes: 574fb258d6 ("Staging: IIO: VTI sca3000 series accelerometer driver (spi)")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make lux_per_bit and lux_per_bit_base_it settings stored in struct
cm32181_chip instead of a hardcoded (defined) values.
This is a preparation patch for reading some ACPI tables which specify
a device specific lux_per_bit value.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use units of 1/100000th for calibscale and lux_per_bit. The similar
cm3232 driver already uses 1/100000th as unit for calibscale.
This allows for higher-accuracy and makes it easier to add support
for getting device-specific calibscale and lux_per_bit values from
a device's ACPI tables, as the values in the ACPI tables also use
1/100000th units.
This units change means that our intermediate values in cm32181_get_lux()
may get quite big, change the type of the lux variable to a u64 to
deal with this.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This is a preparation patch for reading some ACPI tables which give
init values for multiple registers.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Some ACPI systems list 2 I2C resources for the CM3218 sensor. On these
systems the first I2cSerialBus ACPI-resource points to the SMBus Alert
Response Address (ARA, 0x0c) and the second I2cSerialBus ACPI-resource
points to the actual CM3218 sensor address:
Method (_CRS, 0, NotSerialized) // _CRS: Current Resource Settings
{
Name (SBUF, ResourceTemplate ()
{
I2cSerialBusV2 (0x000C, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\_SB.I2C3",
0x00, ResourceConsumer, , Exclusive,
)
I2cSerialBusV2 (0x0048, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\_SB.I2C3",
0x00, ResourceConsumer, , Exclusive,
)
Interrupt (ResourceConsumer, Level, ActiveHigh, Exclusive, ,, )
{
0x00000033,
}
})
Return (SBUF) /* \_SB_.I2C3.ALSD._CRS.SBUF */
}
Detect this and take the following step to deal with it:
1. When a SMBus Alert capable sensor has an Alert asserted, it will
not respond on its actual I2C address. Read a byte from the ARA
to clear any pending Alerts.
2. Create a "dummy" client for the actual I2C address and
use that client to communicate with the sensor.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
3 small cleanups to cm32181_probe():
1. Do not log an error when we fail to allocate memory (as a general
rule drivers do not log errors for this as the kernel will already
have complained loudly that it could not alloc the mem).
2. Remove the i2c_set_clientdata() call, we never use i2c_get_clientdata()
or dev_get_drvdata() anywhere.
3. Add a dev helper variable and use it in various places instead of
&client->dev.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for the CM3218 which is an older version of the
CM32181.
This is based on a newer version of cm32181.c, with a copyright of:
* Copyright (C) 2014 Capella Microsystems Inc.
* Author: Kevin Tsai <ktsai@capellamicro.com>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License version 2, as published
* by the Free Software Foundation.
Which is floating around on the net in various places, but the changes
from this newer version never made it upstream.
This was tested on an Asus T100TA and an Asus T100CHI, which both come
with the CM3218 variant of the light sensor.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These come from a newer version of cm32181.c, which is floating around
the net, with a copyright of:
* Copyright (C) 2014 Capella Microsystems Inc.
* Author: Kevin Tsai <ktsai@capellamicro.com>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License version 2, as published
* by the Free Software Foundation.
Note that this removes the bogus CM32181_CMD_ALS_ENABLE define, there
is no enable bit, only a disable bit and enabled is the absence of
being disabled.
This is a preparation patch for adding support for the older
CM3218 model of the light sensor.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for ACPI enumeration, this has been tested on a HP
HP Pavilion x2 Detachable 10 (Bay Trail model).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Switch to the new style i2c-driver probe_new probe function and drop the
unnecessary i2c_device_id table (we do not have any old style board files
using this).
This is a preparation patch for adding ACPI binding support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The main intent here is to get rid of the iio_buffer_set_attrs() helper, or
at least rework it's usage a bit.
The problem with that helper is that it needs a pointer to the buffer,
which makes supporting multiple buffers per IIO device a bit more
cumbersome.
The hid_sensor_setup_trigger() is pretty much used in the same way:
- iio_triggered_buffer_setup() gets called before
- then hid_sensor_setup_trigger() and hid_sensor_setup_batch_mode() gets
called which may attach some fifo attributes
This change merges the 2 together under the hid_sensor_setup_trigger()
function. Only the &iio_pollfunc_store_time is passed to all devices, so
it's not even required to pass it explicitly outside of the common
hid_sensor_setup_trigger() function.
Moving the devm_iio_triggered_buffer_setup/cleanup() calls into the common
place code can help the rework of the buffer code, since it is in one
place.
One detail of the change is that there are 2 drivers that use
devm_iio_triggered_buffer_setup(). That function gets implicitly
replaced with iio_triggered_buffer_setup()/cleanup(), but since all drivers
call both hid_sensor_setup_trigger9) & hid_sensor_remove_trigger() trigger,
the iio_triggered_buffer_cleanup() piggy backs on the
hid_sensor_remove_trigger() call, which should cover the cleanup.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This adds a new driver for the Cypress CY8CTMA140 touchscreen.
This driver is inspired by out-of-tree code for the Samsung
GT-S7710 mobile phone.
I have tried to compare the structure and behaviour of this
touchscreen to the existing CYTTSP and CYTTSP4 generics and
it seems pretty different. It is also different in character
from the cy8ctmg110_ts.c. It appears to rather be vaguely
related to the Melfas MMS114 driver, yet distinctly
different.
Dmitry Torokhov rewrote the key scanning code during the
submission process so the driver is a joint work.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200506123435.187432-2-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds device tree bindings for the Cypress CY8CTMA140 touchscreen.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200506123435.187432-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20200507185347.GA14499@embeddedor
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In the current codes, the octeontx2 uses its own method to allocate
the pool buffers, but there are some issues in this implementation.
1. We have to run the otx2_get_page() for each allocation cycle and
this is pretty error prone. As I can see there is no invocation
of the otx2_get_page() in otx2_pool_refill_task(), this will leave
the allocated pages have the wrong refcount and may be freed wrongly.
2. It wastes memory. For example, if we only receive one packet in a
NAPI RX cycle, and then allocate a 2K buffer with otx2_alloc_rbuf()
to refill the pool buffers and leave the remain area of the allocated
page wasted. On a kernel with 64K page, 62K area is wasted.
IMHO it is really unnecessary to implement our own method for the
buffers allocate, we can reuse the napi_alloc_frag() to simplify
our code.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If systemd is configured to use hybrid mode which enables the use of
both cgroup v1 and v2, systemd will create new cgroup on both the default
root (v2) and netprio_cgroup hierarchy (v1) for a new session and attach
task to the two cgroups. If the task does some network thing then the v2
cgroup can never be freed after the session exited.
One of our machines ran into OOM due to this memory leak.
In the scenario described above when sk_alloc() is called
cgroup_sk_alloc() thought it's in v2 mode, so it stores
the cgroup pointer in sk->sk_cgrp_data and increments
the cgroup refcnt, but then sock_update_netprioidx()
thought it's in v1 mode, so it stores netprioidx value
in sk->sk_cgrp_data, so the cgroup refcnt will never be freed.
Currently we do the mode switch when someone writes to the ifpriomap
cgroup control file. The easiest fix is to also do the switch when
a task is attached to a new cgroup.
Fixes: bd1060a1d6 ("sock, cgroup: add sock->sk_cgroup")
Reported-by: Yang Yingliang <yangyingliang@huawei.com>
Tested-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
runqslower doesn't specify include path for uapi/bpf.h. This causes the
following warning:
In file included from runqslower.c:10:
.../tools/testing/selftests/bpf/tools/include/bpf/bpf.h:234:38:
warning: 'enum bpf_stats_type' declared inside parameter list will not
be visible outside of this definition or declaration
234 | LIBBPF_API int bpf_enable_stats(enum bpf_stats_type type);
Fix this by adding -I tools/includ/uapi to the Makefile.
Reported-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Song Liu <songliubraving@fb.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
It seems that for whatever reason, gcc-10 ends up not inlining a couple
of functions that used to be inlined before. Even if they only have one
single callsite - it looks like gcc may have decided that the code was
unlikely, and not worth inlining.
The code generation difference is harmless, but caused a few new section
mismatch errors, since the (now no longer inlined) function wasn't in
the __init section, but called other init functions:
Section mismatch in reference from the function kexec_free_initrd() to the function .init.text:free_initrd_mem()
Section mismatch in reference from the function tpm2_calc_event_log_size() to the function .init.text:early_memremap()
Section mismatch in reference from the function tpm2_calc_event_log_size() to the function .init.text:early_memunmap()
So add the appropriate __init annotation to make modpost not complain.
In both cases there were trivially just a single callsite from another
__init function.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The "default n" is not needed as it is, well, default. Clean
the KConfig by removing "default n".
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Indent the help text as explained in
Documentation/process/coding-style.rst
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
