Clock and Power Domain definitions for the Renesas RZ/G1H (R8A7742) SoC,
shared by driver and DT source files.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCXqfi5AAKCRCKwlD9ZEnx
cJcxAP4+fAavWGp1dyIyDdECbmUUNLe6Cw8DN1SVWBlxvy1gugD/TR4Q0QR7dgUZ
ZpeuRTyM7iBDL57TiChwdLyjuFwqpgw=
=l1L1
-----END PGP SIGNATURE-----
Merge tag 'renesas-r8a7742-dt-binding-defs-tag' into clk-renesas-for-v5.8
Renesas RZ/G1H DT Binding Definitions
Clock and Power Domain definitions for the Renesas RZ/G1H (R8A7742) SoC,
shared by driver and DT source files.
mx25u51245g is a mass production for new design and
replace mx66u51235f(phase out).
Validated by read, erase, read back, write and read back
on Xilinx Zynq PicoZed FPGA board which included
Macronix SPI Host (driver/spi/spi-mxic.c).
Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
If probing the LP885x backlight fails after the regulators have been
enabled, then the following warning is seen when releasing the
regulators ...
WARNING: CPU: 1 PID: 289 at drivers/regulator/core.c:2051 _regulator_put.part.28+0x158/0x160
Modules linked in: tegra_xudc lp855x_bl(+) host1x pwm_tegra ip_tables x_tables ipv6 nf_defrag_ipv6
CPU: 1 PID: 289 Comm: systemd-udevd Not tainted 5.6.0-rc2-next-20200224 #1
Hardware name: NVIDIA Jetson TX1 Developer Kit (DT)
...
Call trace:
_regulator_put.part.28+0x158/0x160
regulator_put+0x34/0x50
devm_regulator_release+0x10/0x18
release_nodes+0x12c/0x230
devres_release_all+0x34/0x50
really_probe+0x1c0/0x370
driver_probe_device+0x58/0x100
device_driver_attach+0x6c/0x78
__driver_attach+0xb0/0xf0
bus_for_each_dev+0x68/0xc8
driver_attach+0x20/0x28
bus_add_driver+0x160/0x1f0
driver_register+0x60/0x110
i2c_register_driver+0x40/0x80
lp855x_driver_init+0x20/0x1000 [lp855x_bl]
do_one_initcall+0x58/0x1a0
do_init_module+0x54/0x1d0
load_module+0x1d80/0x21c8
__do_sys_finit_module+0xe8/0x100
__arm64_sys_finit_module+0x18/0x20
el0_svc_common.constprop.3+0xb0/0x168
do_el0_svc+0x20/0x98
el0_sync_handler+0xf4/0x1b0
el0_sync+0x140/0x180
Fix this by ensuring that the regulators are disabled, if enabled, on
probe failure.
Finally, ensure that the vddio regulator is disabled in the driver
remove handler.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
mx25l51245g is a mass production for new design and
replace mx66l51235l(phase out).
Validated by read, erase, read back, write and read back
on Xilinx Zynq PicoZed FPGA board which included
Macronix SPI Host (driver/spi/spi-mxic.c).
Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
When spi_nor_info_init_params(), spi_nor_sfdp_init_params(), and
spi_nor_init_params() were added, the kernel-doc for them contained
a typo: 'struct spi-nor' instead of 'struct spi_nor' -- fix them.
Fixes: 1c1d8d98e1 ("mtd: spi-nor: Split spi_nor_init_params()")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
When spi_nor_manufacturer_init_params() was added, the kernel-doc for it
contained a typo: 'struct spi-nor' instead of 'struct spi_nor' -- fix it.
Fixes: ce0b6f3f3c ("mtd: spi-nor: Add default_init() hook to tweak flash parameters")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
When adding the 'spimem' field to 'struct spi_nor', a grammar mistake
("point" instead of "pointer") was made -- fix it and convert the SPI
acronym to uppercase and fully spell out "memory", while at it...
Fixes: b35b9a1036 ("mtd: spi-nor: Move m25p80 code in spi-nor.c")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
When adding the 'info' field to 'struct spi_nor', some acronyms were in
lower case and some in upper case and the JEDEC acronym mistyped -- fix
these issues.
Fixes: 46dde01f6b ("mtd: spi-nor: add spi_nor_init() function")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
When adding the '{read|write|reg}_proto' fields to 'struct spi_nor', a
colon was missed in the comment for the spi_nor::reg_proto' -- add it.
Fixes: cfc5604c48 ("mtd: spi-nor: introduce SPI 1-2-2 and SPI 1-4-4 protocols")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
When embedding 'struct mtd_info' within 'struct spi_nor', the kernel-doc
comment was forgotten. Fix it by dropping the "pointer to" part from the
comment.
Fixes: 1976367173 ("mtd: spi-nor: embed struct mtd_info within struct spi_nor")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
When introducing 'struct spi_nor', a number of issues was added in its
kernel-doc comment:
- double article in the heading kernel-doc comment;
- "point" instead of "pointer" for the 'mtd' and 'dev' fields;
- "a" articles instead of "an" for the 'dev' field;
- acronyms in the lower case for the 'dev' field;
- missing "pointer to" for the 'priv' field.
Fix all of those at once...
Fixes: 6e602ef733 ("mtd: spi-nor: add the basic data structures")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The SM8250 UFS PHY can run off the same initialization sequence as
SM8150, but add the compatible to allow future changes.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When building the mult_v7_defconfig, ARM_TI_CPUFREQ doesn't get enabled
evenwhen ARCH_OMAP(3|4) is selected. Build ARM_TI_CPUFREQ by default for
ARCH_OMAP2PLUS.
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Commit ed830385a2 ("scsi: ibmvfc: Avoid loss of all paths during SVC node
reboot") introduced a regression where when the client resets or re-enables
its CRQ with the hypervisor there is a chance that if the server side
doesn't issue its INIT handshake quick enough the client can issue an
Implicit Logout prior to doing an NPIV Login. The server treats this
scenario as a protocol violation and closes the CRQ on its end forcing the
client through a reset that gets the client host state and next host action
out of agreement leading to a BUG assert.
ibmvfc 30000003: Partner initialization complete
ibmvfc 30000002: Partner initialization complete
ibmvfc 30000002: Host partner adapter deregistered or failed (rc=2)
ibmvfc 30000002: Partner initialized
------------[ cut here ]------------
kernel BUG at ../drivers/scsi/ibmvscsi/ibmvfc.c:4489!
Oops: Exception in kernel mode, sig: 5 [#1]
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
Supported: No, Unreleased kernel
CPU: 16 PID: 1290 Comm: ibmvfc_0 Tainted: G OE X 5.3.18-12-default
NIP: c00800000d84a2b4 LR: c00800000d84a040 CTR: c00800000d84a2a0
REGS: c00000000cb57a00 TRAP: 0700 Tainted: G OE X (5.3.18-12-default)
MSR: 800000000282b033 <SF,VEC,VSX,EE,FP,ME,IR,DR,RI,LE> CR: 24000848 XER: 00000001
CFAR: c00800000d84a070 IRQMASK: 1
GPR00: c00800000d84a040 c00000000cb57c90 c00800000d858e00 0000000000000000
GPR04: 0000000000000000 0000000000000000 0000000000000000 00000000000000a0
GPR08: c00800000d84a074 0000000000000001 0000000000000014 c00800000d84d7d0
GPR12: 0000000000000000 c00000001ea28200 c00000000016cd98 0000000000000000
GPR16: c00800000d84b7b8 0000000000000000 0000000000000000 c00000542c706d68
GPR20: 0000000000000005 c00000542c706d88 5deadbeef0000100 5deadbeef0000122
GPR24: 000000000000000c 000000000000000b c00800000d852180 0000000000000001
GPR28: 0000000000000000 c00000542c706da0 c00000542c706860 c00000542c706828
NIP [c00800000d84a2b4] ibmvfc_work+0x3ac/0xc90 [ibmvfc]
LR [c00800000d84a040] ibmvfc_work+0x138/0xc90 [ibmvfc]
This scenario can be prevented by rejecting any attempt to send an Implicit
Logout if the client adapter is not logged in yet.
Link: https://lore.kernel.org/r/20200427214824.6890-1-tyreld@linux.ibm.com
Fixes: ed830385a2 ("scsi: ibmvfc: Avoid loss of all paths during SVC node reboot")
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix a use-after-free noticed by running with KASAN enabled. If
rmi_irq_fn() is run twice in a row, then rmi_f11_attention() (among
others) will end up reading from drvdata->attn_data.data, which was
freed and left dangling in rmi_irq_fn().
Commit 55edde9fff ("Input: synaptics-rmi4 - prevent UAF reported by
KASAN") correctly identified and analyzed this bug. However the attempted
fix only NULLed out a local variable, missing the fact that
drvdata->attn_data is a struct, not a pointer.
NULL out the correct pointer in the driver data to prevent the attention
functions from copying from it.
Fixes: 55edde9fff ("Input: synaptics-rmi4 - prevent UAF reported by KASAN")
Fixes: b908d3cd81 ("Input: synaptics-rmi4 - allow to add attention data")
Signed-off-by: Evan Green <evgreen@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200427145537.1.Ic8f898e0147beeee2c005ee7b20f1aebdef1e7eb@changeid
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This reverts commit 1893150646. From Kevin
Locke:
"... nomux only appeared to fix the issue because the controller
continued working after warm reboots. After more thorough testing from
both warm and cold start, I now believe the entry should be added to
i8042_dmi_reset_table rather than i8042_dmi_nomux_table as i8042.reset=1
alone is sufficient to avoid the issue from both states while
i8042.nomux is not."
Allow the firmware to specify the mapping between the scan code and the
linux keycode. This takes the form of a "linux,keymap" property which is
an array of u32 values, each value specifying mapping for a key.
Signed-off-by: Rajat Jain <rajatja@google.com>
Link: https://lore.kernel.org/r/20200427210259.91330-3-rajatja@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Certain keyboards have their top-row keys intended for actions such as
"Browser back", "Browser Refresh", "Fullscreen" etc as their primary mode,
thus they will send scan codes for those actions. Further, they don't
have a dedicated "Fn" key so don't have the capability to generate
function key codes (e.g. F1, F2 etc..). However in this case, if
userspace still wants to "synthesize" those function keys using the top
row action keys, it needs to know the physical position of the top row
keys. (Essentially a mapping between usage codes and a physical location
in the top row).
This patch enhances the atkbd driver to receive such a mapping from the
firmware / device tree, and expose it to userspace in the form of a
function-row-physmap attribute. The attribute would be a space separated
ordered list of physical codes, for the keys in the function row, in
left-to-right order.
The attribute will only be present if the kernel knows about such mapping,
otherwise the attribute shall not be visible.
Signed-off-by: Rajat Jain <rajatja@google.com>
Link: https://lore.kernel.org/r/20200427210259.91330-2-rajatja@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Attach the firmware node to the serio i8042 kbd device so that device
properties can be passed from the firmware.
Signed-off-by: Rajat Jain <rajatja@google.com>
Link: https://lore.kernel.org/r/20200427210259.91330-1-rajatja@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch allows you to NAT the network address prefix onto another
network address prefix, a.k.a. netmapping.
Userspace must specify the NF_NAT_RANGE_NETMAP flag and the prefix
address through the NFTA_NAT_REG_ADDR_MIN and NFTA_NAT_REG_ADDR_MAX
netlink attributes.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Instead of EINVAL which should be used for malformed netlink messages.
Fixes: eb31628e37 ("netfilter: nf_tables: Add support for IPv6 NAT")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Despite of functions being documented, they are not in the kernel-doc
specification, and could not be included in kernel documentation. Change
the style of functions comments to be compliant to the kernel-doc style.
When the function comments are outdated, update then.
[mkp: a few edits]
Link: https://lore.kernel.org/r/20200419050148.33371-1-andrealmeid@collabora.com
Signed-off-by: André Almeida <andrealmeid@collabora.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The write performance of TLC NAND is considerably lower than SLC NAND.
Using SLC NAND as a WriteBooster Buffer enables the write request to be
processed with lower latency and improves the overall write performance.
Adds support for shared-buffer mode WriteBooster.
WriteBooster enable: SW enables it when clocks are scaled up, thus it's
enabled only in high load conditions.
WriteBooster disable: SW will disable the feature, when clocks are scaled
down. Thus writes would go as normal writes.
To keep the endurance of the WriteBooster Buffer at a maximum, this
load-based toggling is adopted.
Link: https://lore.kernel.org/r/2871444d9083b0e9323ef6d8ff1b544b7784adc9.1587591527.git.asutoshd@codeaurora.org
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the following coccicheck warning:
drivers/scsi/ufs/ufshcd.c:4140:6-14: WARNING: Assignment of 0/1 to bool
variable.
Link: https://lore.kernel.org/r/20200426094305.24083-1-yanaijie@huawei.com
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch makes the sr code slightly easier to read.
Link: https://lore.kernel.org/r/20200427014844.12109-1-bvanassche@acm.org
Cc: Merlijn Wajer <merlijn@archive.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If 'scsi_host_alloc()' or 'kcalloc()' fail, 'error' is known to be 0. Set
it explicitly to -ENOMEM before branching to the error handling path.
While at it, remove 2 useless assignments to 'error'. These values are
overwridden a few lines later.
Link: https://lore.kernel.org/r/20200412094039.8822-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix to return negative error code -ENOMEM from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 60abd3181d ("selinux: convert cond_list to array")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
tcp_bpf_recvmsg() invokes sk_psock_get(), which returns a reference of
the specified sk_psock object to "psock" with increased refcnt.
When tcp_bpf_recvmsg() returns, local variable "psock" becomes invalid,
so the refcount should be decreased to keep refcount balanced.
The reference counting issue happens in several exception handling paths
of tcp_bpf_recvmsg(). When those error scenarios occur such as "flags"
includes MSG_ERRQUEUE, the function forgets to decrease the refcnt
increased by sk_psock_get(), causing a refcnt leak.
Fix this issue by calling sk_psock_put() or pulling up the error queue
read handling when those error scenarios occur.
Fixes: e7a5f1f1cd ("bpf/sockmap: Read psock ingress_msg before sk_receive_queue")
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/1587872115-42805-1-git-send-email-xiyuyang19@fudan.edu.cn
-----BEGIN PGP SIGNATURE-----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=Tbyq
-----END PGP SIGNATURE-----
Merge tag 'for-5.7-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- regression fixes:
- transaction leak when deleting unused block group
- log cleanup after transaction abort
- fix block group leak when removing fails
- transaction leak if relocation recovery fails
- fix SPDX header
* tag 'for-5.7-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: fix transaction leak in btrfs_recover_relocation
btrfs: fix block group leak when removing fails
btrfs: drop logs when we've aborted a transaction
btrfs: fix memory leak of transaction when deleting unused block group
btrfs: discard: Use the correct style for SPDX License Identifier
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEIbPD0id6easf0xsudhRwX5BBoF4FAl6mwOETHHdlaS5saXVA
a2VybmVsLm9yZwAKCRB2FHBfkEGgXrFLB/4yKsrl41WwYRbTKgiir576/LA0vGxQ
cZjUQwkVv3S5/AfhvpwiGFV4dBV6j81KtNhRE6luaa3FBHObnjrx5tNqMw/P8a0j
HZGZ68n4qE+OPVtTxj54s81iWIi9vgT/La92GPYhuXoiVPTd5zJ2lwY3so04BSFJ
p30+RZFKNkTjNYZNZSHcoodr+js4Uws8JSn8OmpCJr8Gt+FJqkujQROG3HMKhJlk
KlJlCJhV48tj/nlgcbGHBF0Yy5l8DVCaKIz+MiF5F/i+P8r0cErfyihc9Ene0/un
LNFhIVGn8/MTi0CVrltcnur2qFH1qPCuLolKSpd/FKd6H2UDgK16XgAd
=NJP/
-----END PGP SIGNATURE-----
Merge tag 'hyperv-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull Hyper-V fixes from Wei Liu:
- Two patches from Dexuan fixing suspension bugs
- Three cleanup patches from Andy and Michael
* tag 'hyperv-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
hyper-v: Remove internal types from UAPI header
hyper-v: Use UUID API for exporting the GUID
x86/hyperv: Suspend/resume the VP assist page for hibernation
Drivers: hv: Move AEOI determination to architecture dependent code
Drivers: hv: vmbus: Fix Suspend-to-Idle for Generation-2 VM
In case of error, the function gen_pool_create() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: 93a7653031 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a number of consumer mainboards where the BIOS leaves the PHY
in a state that it's reporting an invalid PHY ID. To detect such cases
add the PHY ID to the error message if no dedicated PHY driver is found.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Except for a few of the networking hooks called from modular ipv4
or ipv6 code, all of hooks are just called from guaranteed to be
built-in code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrey Ignatov <rdna@fb.com>
Link: https://lore.kernel.org/bpf/20200424064338.538313-2-hch@lst.de
While we support using both tx slots for sideband transmissions, it
appears that DisplayPort devices in the field didn't end up doing a very
good job of supporting it. From section 5.2.1 of the DP 2.0
specification:
There are MST Sink/Branch devices in the field that do not handle
interleaved message transactions.
To facilitate message transaction handling by downstream devices, an
MST Source device shall generate message transactions in an atomic
manner (i.e., the MST Source device shall not concurrently interleave
multiple message transactions). Therefore, an MST Source device shall
clear the Message_Sequence_No value in the Sideband_MSG_Header to 0.
This might come as a bit of a surprise since the vast majority of hubs
will support using both tx slots even if they don't support interleaved
message transactions, and we've also been using both tx slots since MST
was introduced into the kernel.
However, there is one device we've had trouble getting working
consistently with MST for so long that we actually assumed it was just
broken: the infamous Dell P2415Qb. Previously this monitor would appear
to work sometimes, but in most situations would end up timing out
LINK_ADDRESS messages almost at random until you power cycled the whole
display. After reading section 5.2.1 in the DP 2.0 spec, some closer
investigation into this infamous display revealed it was only ever
timing out on sideband messages in the second TX slot.
Sure enough, avoiding the second TX slot has suddenly made this monitor
function perfectly for the first time in five years. And since they
explicitly mention this in the specification, I doubt this is the only
monitor out there with this issue. This might even explain explain the
seemingly harmless garbage sideband responses we would occasionally see
with MST hubs!
So - rewrite our sideband TX handlers to only support one TX slot. In
order to simplify our sideband handling now that we don't support
transmitting to multiple MSTBs at once, we also move all state tracking
for down replies from mstbs to the topology manager.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: ad7f8a1f9c ("drm/helper: add Displayport multi-stream helper (v0.6)")
Cc: Sean Paul <sean@poorly.run>
Cc: "Lin, Wayne" <Wayne.Lin@amd.com>
Cc: <stable@vger.kernel.org> # v3.17+
Reviewed-by: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20200424181308.770749-1-lyude@redhat.com
- bump version strings, by Simon Wunderlich
- fix spelling error, by Sven Eckelmann
- drop unneeded types.h include, by Sven Eckelmann
- change random number generation to prandom_u32_max(),
by Sven Eckelmann
- remove unused function batadv_arp_change_timeout(), by Yue Haibing
-----BEGIN PGP SIGNATURE-----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=5bKt
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20200427' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- fix spelling error, by Sven Eckelmann
- drop unneeded types.h include, by Sven Eckelmann
- change random number generation to prandom_u32_max(),
by Sven Eckelmann
- remove unused function batadv_arp_change_timeout(), by Yue Haibing
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- fix random number generation in network coding, by George Spelvin
- fix reference counter leaks, by Xiyu Yang (3 patches)
-----BEGIN PGP SIGNATURE-----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=fNPb
-----END PGP SIGNATURE-----
Merge tag 'batadv-net-for-davem-20200427' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here are some batman-adv bugfixes:
- fix random number generation in network coding, by George Spelvin
- fix reference counter leaks, by Xiyu Yang (3 patches)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
