Currently rx tid setup is happening for TID 0 and TID 16
during peer setup. And if other TID packets received for
the peer it will be redirected to rx error ring and not through
reo ring. And this rx tid configuration cannot be done
in the rx error ring path since it is a atomic context.
So moving the rx tid setup for all tids during the peer setup.
This is required to enable PN offload functionality to route
all packets through reo ring.
Co-developed-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Before this change, after writing "warm_hw_reset" debugfs file, host
will send chip reset command to FW even though FW do not support this
service getting a warning print.
Though there is no FW impact before this change, this patch restricts
chip reset command sent to FW only if FW advertises the support via WMI
service bit.
Removed the redundant check and ath10k_warn() print as well.
New version FW will report chip reset service bit to host. Host allow user
to trigger WLAN chip reset only when fw report this service bit.
For older NON-TLV FW, since it do not report chip reset service bit, host
will not send chip reset command. For older TLV FW, since it report chip
reset service bit, host will send chip reset command.
Tested HW: QCA9984, WCN3990
QCA9984 FW version: WLAN.BL.3.9.0.2-00042-S-1
Signed-off-by: Yingying Tang <yintang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When running simulate crash stress test, it happened
"failed to read from address 0x800: -110".
Test steps:
1. Run command continuous
echo soft > /sys/kernel/debug/ieee80211/phy0/ath10k/simulate_fw_crash
2. error happened and it did not begin recovery for long time.
[74377.334846] ath10k_sdio mmc1:0001:1: simulating soft firmware crash
[74378.378217] ath10k_sdio mmc1:0001:1: failed to read from address 0x800: -110
[74378.378371] ath10k_sdio mmc1:0001:1: failed to process pending SDIO interrupts: -110
It has sdio errors since it can not read MBOX_HOST_INT_STATUS_ADDRESS,
then it has to do recovery process to recovery ath10k.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add hardware parameters for QCA9377 sdio devices, it's now properly supported.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This does three inter-related things to clarify the usage of the
platform device dma_mask field. In the process, fix the bug introduced
by cdfee56232 ("driver core: initialize a default DMA mask for
platform device") that caused Artem Tashkinov's laptop to not boot with
newer Fedora kernels.
This does:
- First off, rename the field to "platform_dma_mask" to make it
greppable.
We have way too many different random fields called "dma_mask" in
various data structures, where some of them are actual masks, and
some of them are just pointers to the mask. And the structures all
have pointers to each other, or embed each other inside themselves,
and "pdev" sometimes means "platform device" and sometimes it means
"PCI device".
So to make it clear in the code when you actually use this new field,
give it a unique name (it really should be something even more unique
like "platform_device_dma_mask", since it's per platform device, not
per platform, but that gets old really fast, and this is unique
enough in context).
To further clarify when the field gets used, initialize it when we
actually start using it with the default value.
- Then, use this field instead of the random one-off allocation in
platform_device_register_full() that is now unnecessary since we now
already have a perfectly fine allocation for it in the platform
device structure.
- The above then allows us to fix the actual bug, where the error path
of platform_device_register_full() would unconditionally free the
platform device DMA allocation with 'kfree()'.
That kfree() was dont regardless of whether the allocation had been
done earlier with the (now removed) kmalloc, or whether
setup_pdev_dma_masks() had already been used and the dma_mask pointer
pointed to the mask that was part of the platform device.
It seems most people never triggered the error path, or only triggered
it from a call chain that set an explicit pdevinfo->dma_mask value (and
thus caused the unnecessary allocation that was "cleaned up" in the
error path) before calling platform_device_register_full().
Robin Murphy points out that in Artem's case the wdat_wdt driver failed
in platform_device_add(), and that was the one that had called
platform_device_register_full() with pdevinfo.dma_mask = 0, and would
have caused that kfree() of pdev.dma_mask corrupting the heap.
A later unrelated kmalloc() then oopsed due to the heap corruption.
Fixes: cdfee56232 ("driver core: initialize a default DMA mask for platform device")
Reported-bisected-and-tested-by: Artem S. Tashkinov <aros@gmx.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, OTP is downloaded twice in case of "pre-cal-dt"
and "pre-cal-file" to fetch the board ID and takes around
~2 sec more boot uptime.
First OTP download happens in "ath10k_core_probe_fw" and
second in ath10k_core_start. First boot does not need OTP
download in core start when valid board id acquired.
The second OTP download is required upon core stop/start.
This patch skips the OTP download when first OTP download
has acquired a valid board id. This patch also marks board
id invalid in "ath10k_core_stop", which will force the OTP
download in ath10k_core_start and fetches valid board id.
Tested HW: QCA9984
Tested FW: 10.4-3.6-00104
Signed-off-by: Vikas Patel <vikpatel@codeaurora.org>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Register range of display clocks is 0x10000, as it can be seen from
DE2 documentation.
Fix it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Fixes: 2c796fc8f5 ("arm64: dts: allwinner: a64: add necessary device tree nodes for DE2 CCU")
[wens@csie.org: added fixes tag]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Just dereference bp->b_addr directly and make the code a little
simpler and more clear.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Just dereference bp->b_addr directly and make the code a little
simpler and more clear.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Just dereference bp->b_addr directly and make the code a little
simpler and more clear.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
There is just a single user left, so remove it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
struct xfs_agfl is a header in front of the AGFL entries that exists
for CRC enabled file systems. For not CRC enabled file systems the AGFL
is simply a list of agbno. Make the CRC case similar to that by just
using the list behind the new header. This indirectly solves a problem
with modern gcc versions that warn about taking addresses of packed
structures (and we have to pack the AGFL given that gcc rounds up
structure sizes). Also replace the helper macro to get from a buffer
with an inline function in xfs_alloc.h to make the code easier to
read.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Leaving PF_MEMALLOC set when exiting a kthread causes it to remain set
during do_exit(). That can confuse things. In particular, if BSD
process accounting is enabled, then do_exit() writes data to an
accounting file. If that file has FS_SYNC_FL set, then this write
occurs synchronously and can misbehave if PF_MEMALLOC is set.
For example, if the accounting file is located on an XFS filesystem,
then a WARN_ON_ONCE() in iomap_do_writepage() is triggered and the data
doesn't get written when it should. Or if the accounting file is
located on an ext4 filesystem without a journal, then a WARN_ON_ONCE()
in ext4_write_inode() is triggered and the inode doesn't get written.
Fix this in xfsaild() by using the helper functions to save and restore
PF_MEMALLOC.
This can be reproduced as follows in the kvm-xfstests test appliance
modified to add the 'acct' Debian package, and with kvm-xfstests's
recommended kconfig modified to add CONFIG_BSD_PROCESS_ACCT=y:
mkfs.xfs -f /dev/vdb
mount /vdb
touch /vdb/file
chattr +S /vdb/file
accton /vdb/file
mkfs.xfs -f /dev/vdc
mount /vdc
umount /vdc
It causes:
WARNING: CPU: 1 PID: 336 at fs/iomap/buffered-io.c:1534
CPU: 1 PID: 336 Comm: xfsaild/vdc Not tainted 5.6.0-rc5 #3
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ?-20191223_100556-anatol 04/01/2014
RIP: 0010:iomap_do_writepage+0x16b/0x1f0 fs/iomap/buffered-io.c:1534
[...]
Call Trace:
write_cache_pages+0x189/0x4d0 mm/page-writeback.c:2238
iomap_writepages+0x1c/0x33 fs/iomap/buffered-io.c:1642
xfs_vm_writepages+0x65/0x90 fs/xfs/xfs_aops.c:578
do_writepages+0x41/0xe0 mm/page-writeback.c:2344
__filemap_fdatawrite_range+0xd2/0x120 mm/filemap.c:421
file_write_and_wait_range+0x71/0xc0 mm/filemap.c:760
xfs_file_fsync+0x7a/0x2b0 fs/xfs/xfs_file.c:114
generic_write_sync include/linux/fs.h:2867 [inline]
xfs_file_buffered_aio_write+0x379/0x3b0 fs/xfs/xfs_file.c:691
call_write_iter include/linux/fs.h:1901 [inline]
new_sync_write+0x130/0x1d0 fs/read_write.c:483
__kernel_write+0x54/0xe0 fs/read_write.c:515
do_acct_process+0x122/0x170 kernel/acct.c:522
slow_acct_process kernel/acct.c:581 [inline]
acct_process+0x1d4/0x27c kernel/acct.c:607
do_exit+0x83d/0xbc0 kernel/exit.c:791
kthread+0xf1/0x140 kernel/kthread.c:257
ret_from_fork+0x27/0x50 arch/x86/entry/entry_64.S:352
This bug was originally reported by syzbot at
https://lore.kernel.org/r/0000000000000e7156059f751d7b@google.com.
Reported-by: syzbot+1f9dc49e8de2582d90c2@syzkaller.appspotmail.com
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
If regular inode has no compressed cluster, allow using 'chattr -c'
to remove its compress flag, recovering it to a non-compressed file.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Compressed cluster can be generated during dirty data writeback,
if there is dirty pages on compressed inode, it needs to disable
converting compressed inode to non-compressed one.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
stat_inc_compr_inode() needs to check FI_COMPRESSED_FILE flag, so
in f2fs_disable_compressed_file(), we should call stat_dec_compr_inode()
before clearing FI_COMPRESSED_FILE flag.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Legacy mips soc platforms that have controller v5.0 and 6.0 use
flash-edu block for dma transfers. This change adds support for
nand dma transfers using the EDU block.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200122213313.35820-4-kdasu.kdev@gmail.com
Nand controller v5.0 and v6.0 have nand edu blocks that enable
dma nand flash transfers. This allows for faster read and write
access.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Acked-by: Paul Burton <paulburton@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200122213313.35820-3-kdasu.kdev@gmail.com
Increase bad block marker size from one byte to two bytes.
Bad block marker is handled by skip bytes feature of HPNFC.
Controller expects this value to be an even number.
Fixes: ec4ba01e89 ("mtd: rawnand: Add new Cadence NAND driver to MTD subsystem")
Cc: stable@vger.kernel.org
Signed-off-by: Piotr Sroka <piotrs@cadence.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1581328530-29966-3-git-send-email-piotrs@cadence.com
The value of cdns_chip->sector_count is not known at the moment
of the derivation of ecc_size, leading to a zero value. Fix
this by assigning ecc_size later in the code.
Fixes: ec4ba01e89 ("mtd: rawnand: Add new Cadence NAND driver to MTD subsystem")
Cc: stable@vger.kernel.org
Signed-off-by: Piotr Sroka <piotrs@cadence.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1581328530-29966-2-git-send-email-piotrs@cadence.com
Add checking size of BCH meta data size in capabilities registers
instead of using fixed value. BCH meta data is used to keep data
from NAND flash OOB area.
Signed-off-by: Piotr Sroka <piotrs@cadence.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1581328530-29966-1-git-send-email-piotrs@cadence.com
This driver has no arch-specific instructions but is only ever useful
on MIPS; so disable this driver if we're not compiling for MIPS, unless
the driver is compile-tested.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200302184509.10666-1-paul@crapouillou.net
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
Use using dma_request_chan() directly and inform user of error in case the
DMA request failed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200227123749.24064-8-peter.ujfalusi@ti.com
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
Use using dma_request_chan() directly to return the real error code.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200227123749.24064-7-peter.ujfalusi@ti.com
In case when DMA channel request or alloc_bam_transaction() fails,
dma_unmap_single() and any channels already requested should be released.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200227123749.24064-6-peter.ujfalusi@ti.com
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200227123749.24064-5-peter.ujfalusi@ti.com
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
Use using dma_request_chan() directly to return the real error code.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200227123749.24064-4-peter.ujfalusi@ti.com
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
Use using dma_request_chan() directly to return the real error code.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200227123749.24064-2-peter.ujfalusi@ti.com
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200226222722.GA18020@embeddedor
Currently when marking a block, we use spinand_erase_op() to erase
the block before writing the marker to the OOB area. Doing so without
waiting for the operation to finish can lead to the marking failing
silently and no bad block marker being written to the flash.
In fact we don't need to do an erase at all before writing the BBM.
The ECC is disabled for raw accesses to the OOB data and we don't
need to work around any issues with chips reporting ECC errors as it
is known to be the case for raw NAND.
Fixes: 7529df4652 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200218100432.32433-4-frieder.schrempf@kontron.de
When writing the bad block marker to the OOB area the access mode
should be set to MTD_OPS_RAW as it is done for reading the marker.
Currently this only works because req.mode is initialized to
MTD_OPS_PLACE_OOB (0) and spinand_write_to_cache_op() checks for
req.mode != MTD_OPS_AUTO_OOB.
Fix this by explicitly setting req.mode to MTD_OPS_RAW.
Fixes: 7529df4652 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200218100432.32433-3-frieder.schrempf@kontron.de
For reading and writing the bad block markers, spinand->oobbuf is
currently used as a buffer for the marker bytes. During the
underlying read and write operations to actually get/set the content
of the OOB area, the content of spinand->oobbuf is reused and changed
by accessing it through spinand->oobbuf and/or spinand->databuf.
This is a flaw in the original design of the SPI NAND core and at the
latest from 13c15e07ee ("mtd: spinand: Handle the case where
PROGRAM LOAD does not reset the cache") on, it results in not having
the bad block marker written at all, as the spinand->oobbuf is
cleared to 0xff after setting the marker bytes to zero.
To fix it, we now just store the two bytes for the marker on the
stack and let the read/write operations copy it from/to the page
buffer later.
Fixes: 7529df4652 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200218100432.32433-2-frieder.schrempf@kontron.de
Macronix NANDs support randomizer operation for user data scrambled,
which can be enabled with a SET_FEATURE.
User data written to the NAND device without randomizer is still readable
after randomizer function enabled.
The penalty of randomizer are subpage accesses prohibited and more time
period is needed in program operation and entering deep power-down mode.
i.e., tPROG 300us to 340us(randomizer enabled)
For more high-reliability concern, if subpage write not available with
hardware ECC and then to enable randomizer is recommended by default.
Driver checks byte 167 of Vendor Blocks in ONFI parameter page table
to see if this high-reliability function is supported. By adding a new
specific DT property in children nodes to enable randomizer function.
Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1581922600-25461-2-git-send-email-masonccyang@mxic.com.tw
In order to be merged with "gpio-nand", the driver must support custom
(non-GPIO) I/O accessors.
Allow platforms to omit data GPIO port as well as NWE pin info from
device setup. For the driver to still work on such platform, custom
I/O accessors as well as a custom probe function which initialises the
driver private structure with those accessors must be added to the
driver.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200212003929.6682-14-jmkrzyszt@gmail.com
For consistency with adjacent code patterns used in the driver probe
function, store data GPIO array pointer directly in a respective field
of the driver private structure instead of storing it intermediately
in a local variable for error checking.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200212003929.6682-13-jmkrzyszt@gmail.com
In preparation for extending the driver with custom I/O support, try to
obtain device specific initialisation routine from a matching device
table entry and run it as an additional step of device probe.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200212003929.6682-12-jmkrzyszt@gmail.com
In preparation for merging the driver with "gpio-nand", introduce
module device tables where new device models can be accommodated as
soon as respective support is added.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200212003929.6682-11-jmkrzyszt@gmail.com
Add the new A33 SS compatible to the crypto node.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
