The current URL mentioned in iwlwifi's W entry is outdated and
currently pointing to a dead link. Change it so that it points to the
correct Wiki page directly.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* Fix a locking issue in time events handling;
* A fix in rate-scaling;
* Fix for a potential NULL pointer deref;
* Enable antenna diversity in some devices that were erroneously not
doing it;
* Allow FW dumps to continue when the FW is stuck;
* A fix in the HE capabilities handling;
* Another fix for FW dumps where we were reading wrong addresses.
-----BEGIN PGP SIGNATURE-----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=0Le+
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-kalle-2020-03-08' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
First batch of fixes intended for v5.6
* Fix a locking issue in time events handling;
* A fix in rate-scaling;
* Fix for a potential NULL pointer deref;
* Enable antenna diversity in some devices that were erroneously not
doing it;
* Allow FW dumps to continue when the FW is stuck;
* A fix in the HE capabilities handling;
* Another fix for FW dumps where we were reading wrong addresses.
The Logitech G Powerplay has a lightspeed receiver with a static HID++
device with ID 7 attached to it to. It is used to configure the led on
the mat. For this reason I increased the max number of devices.
Signed-off-by: Filipe Laíns <lains@archlinux.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This makes it possible to test the error path in blk_mq_realloc_hw_ctxs()
and also several error paths in null_blk.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: Johannes Thumshirn <jth@kernel.org>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If null_add_dev() fails then null_del_dev() is called with a NULL argument.
Make null_del_dev() handle this scenario correctly. This patch fixes the
following KASAN complaint:
null-ptr-deref in null_del_dev+0x28/0x280 [null_blk]
Read of size 8 at addr 0000000000000000 by task find/1062
Call Trace:
dump_stack+0xa5/0xe6
__kasan_report.cold+0x65/0x99
kasan_report+0x16/0x20
__asan_load8+0x58/0x90
null_del_dev+0x28/0x280 [null_blk]
nullb_group_drop_item+0x7e/0xa0 [null_blk]
client_drop_item+0x53/0x80 [configfs]
configfs_rmdir+0x395/0x4e0 [configfs]
vfs_rmdir+0xb6/0x220
do_rmdir+0x238/0x2c0
__x64_sys_unlinkat+0x75/0x90
do_syscall_64+0x6f/0x2f0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Cc: Johannes Thumshirn <jth@kernel.org>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Instead of initializing null_blk hardware queues explicitly after the
request queue has been created, provide .init_hctx() and .exit_hctx()
callback functions. The latter functions are not only called during
request queue allocation but also when the number of hardware queues
changes. Allocate nr_cpu_ids queues during initialization to support
increasing the number of hardware queues above the initial hardware
queue count.
This change fixes increasing the number of hardware queues above the
initial number of hardware queues and also keeps nullb->nr_queues in
sync with the number of hardware queues.
Fixes: 45919fbfe1 ("null_blk: Enable modifying 'submit_queues' after an instance has been configured")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: Johannes Thumshirn <jth@kernel.org>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Although it is not clear to me why UBSAN complains when 'memory_backed'
is set, this patch suppresses the UBSAN complaint that is triggered when
setting that configfs attribute.
UBSAN: Undefined behaviour in drivers/block/null_blk_main.c:327:1
load of value 16 is not a valid value for type '_Bool'
CPU: 2 PID: 8396 Comm: check Not tainted 5.6.0-rc1-dbg+ #14
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
Call Trace:
dump_stack+0xa5/0xe6
ubsan_epilogue+0x9/0x26
__ubsan_handle_load_invalid_value+0x6d/0x76
nullb_device_memory_backed_store.cold+0x2c/0x38 [null_blk]
configfs_write_file+0x1c4/0x250 [configfs]
__vfs_write+0x4c/0x90
vfs_write+0x145/0x2c0
ksys_write+0xd7/0x180
__x64_sys_write+0x47/0x50
do_syscall_64+0x6f/0x2f0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Cc: Johannes Thumshirn <jth@kernel.org>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
q->nr_hw_queues must only be updated once it is known that
blk_mq_realloc_hw_ctxs() has succeeded. Otherwise it can happen that
reallocation fails and that q->nr_hw_queues is larger than the number of
allocated hardware queues. This patch fixes the following crash if
increasing the number of hardware queues fails:
BUG: KASAN: null-ptr-deref in blk_mq_map_swqueue+0x775/0x810
Write of size 8 at addr 0000000000000118 by task check/977
CPU: 3 PID: 977 Comm: check Not tainted 5.6.0-rc1-dbg+ #8
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
Call Trace:
dump_stack+0xa5/0xe6
__kasan_report.cold+0x65/0x99
kasan_report+0x16/0x20
check_memory_region+0x140/0x1b0
memset+0x28/0x40
blk_mq_map_swqueue+0x775/0x810
blk_mq_update_nr_hw_queues+0x468/0x710
nullb_device_submit_queues_store+0xf7/0x1a0 [null_blk]
configfs_write_file+0x1c4/0x250 [configfs]
__vfs_write+0x4c/0x90
vfs_write+0x145/0x2c0
ksys_write+0xd7/0x180
__x64_sys_write+0x47/0x50
do_syscall_64+0x6f/0x2f0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Fixes: ac0d6b926e ("block: Reduce the amount of memory required per request queue")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Cc: Keith Busch <kbusch@kernel.org>
Cc: Johannes Thumshirn <jth@kernel.org>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blk_mq_map_queues() and multiple .map_queues() implementations expect that
set->map[HCTX_TYPE_DEFAULT].nr_queues is set to the number of hardware
queues. Hence set .nr_queues before calling these functions. This patch
fixes the following kernel warning:
WARNING: CPU: 0 PID: 2501 at include/linux/cpumask.h:137
Call Trace:
blk_mq_run_hw_queue+0x19d/0x350 block/blk-mq.c:1508
blk_mq_run_hw_queues+0x112/0x1a0 block/blk-mq.c:1525
blk_mq_requeue_work+0x502/0x780 block/blk-mq.c:775
process_one_work+0x9af/0x1740 kernel/workqueue.c:2269
worker_thread+0x98/0xe40 kernel/workqueue.c:2415
kthread+0x361/0x430 kernel/kthread.c:255
Fixes: ed76e329d7 ("blk-mq: abstract out queue map") # v5.0
Reported-by: syzbot+d44e1b26ce5c3e77458d@syzkaller.appspotmail.com
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Cc: Johannes Thumshirn <jth@kernel.org>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The 'hctx_list' member of struct blk_mq_hw_ctx is not a list head but
instead an entry in q->unused_hctx_list. Fix the comment above this
struct member.
Fixes: d386732bc1 ("blk-mq: fill header with kernel-doc")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Cc: André Almeida <andrealmeid@collabora.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
v5.4 changes in soc-core tightened the checks on soc_dapm_add_routes,
which results in the ASoC card probe failing.
Introduce a flag to be set in machine drivers to prevent the probe
from stopping in case of incomplete topologies or missing routes. This
flag is for backwards compatibility only and shall not be used for
newer machine drivers.
Example with an HDaudio card with a bad topology:
[ 236.177898] skl_hda_dsp_generic skl_hda_dsp_generic: ASoC: Failed to
add route iDisp1_out -> direct -> iDisp1 Tx
[ 236.177902] skl_hda_dsp_generic skl_hda_dsp_generic:
snd_soc_bind_card: snd_soc_dapm_add_routes failed: -19
with the disable_route_checks set:
[ 64.031657] skl_hda_dsp_generic skl_hda_dsp_generic: ASoC: Failed to
add route iDisp1_out -> direct -> iDisp1 Tx
[ 64.031661] skl_hda_dsp_generic skl_hda_dsp_generic:
snd_soc_bind_card: disable_route_checks set, ignoring errors on
add_routes
Fixes: daa480bde6 ("ASoC: soc-core: tidyup for snd_soc_dapm_add_routes()")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20200309192744.18380-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
User space cannot disable interrupts any longer so trace return to user space
unconditionally as IRQS_ON.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexandre Chartre <alexandre.chartre@oracle.com>
Link: https://lkml.kernel.org/r/20200308222609.314596327@linutronix.de
MCP2221 is a USB HID to I2C/SMbus host bridge device. This
commit implements i2c and smbus host adapter support. 7-bit
address and i2c multi-message transaction is also supported.
Signed-off-by: Rishi Gupta <gupt21@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If a GPIO we are trying to use is not available and we are deferring
the probe, don't output an error message.
This seems to have been the intent of commit 05c7477885
("i2c: gpio: Add support for named gpios in DT") but the error was
still output due to not checking the updated 'retdesc'.
Fixes: 05c7477885 ("i2c: gpio: Add support for named gpios in DT")
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit af503716ac made sure OF devices get an OF style modalias with
I2C events. It assumed all in-tree users were converted, yet it missed
some Macintosh drivers.
Add an OF module device table for all windfarm drivers to make them
automatically load again.
Fixes: af503716ac ("i2c: core: report OF style module alias for devices registered via OF")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199471
Reported-by: Erhard Furtner <erhard_f@mailbox.org>
Tested-by: Erhard Furtner <erhard_f@mailbox.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org # v4.17+
Now that there is a "real" solution for exfat in the vfs tree queued up
to be merged in 5.7-rc1 the "old" exfat code in staging can be removed.
Many thanks to Valdis for doing the work to get this into the tree in
the first place, it was greatly appreciated.
Acked-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Cc: Pali Rohár <pali@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Namjae Jeon <namjae.jeon@samsung.com>
Cc: Sungjong Seo <sj1557.seo@samsung.com>
Cc: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20200310105421.GA2810679@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
IRQ levels are now handled within the IRQ core. Remove the forgotten
references from the documentation.
Fixes: 9b9f2b8bc2 ("i2c: i2c-smbus: Use threaded irq for smbalert")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Only few drivers use this call, so drivers and I2C core are converted at
once with this patch. By simply using i2c_new_client_device() instead of
i2c_new_device(), we easily can return an ERRPTR for this function as
well. To make out of tree users aware that something changed, the
function is renamed to i2c_new_smbus_alert_device().
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add a new stm32mp15 specific compatible to handle FastMode+
registers handling which is different on the stm32mp15 compared
to the stm32f7 or stm32h7.
Indeed, on the stm32mp15, the FastMode+ set and clear registers
are separated while on the other platforms (F7 or H7) the control
is done in a unique register.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Defer the initial enabling of the Fast Mode Plus bits after the
stm32f7_i2c_setup_timing call in probe function in order to avoid
enabling them if speed is downgraded.
Clear & restore the Fast Mode Plus bits in the suspend/resume
handlers of the driver.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Always wait on the start of the signaler request to reduce the problem
of dequeueing the bonded pair too early -- we want both payloads to
start at the same time, with no latency, and yet still allow others to
make full use of the slack in the system. This reduce the amount of time
we spend waiting on the semaphore used to synchronise the start of the
bonded payload.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306133852.3420322-3-chris@chris-wilson.co.uk
In Pete Goodliffe words, "You can improve a system by adding new code. You
can also improve a system by removing code" - In this case, commit
"202b52b7fb" added new code to initialize end of the node. So, there
is no need for duplicated initialization, and this patch simply removes it.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200309151156.25040-1-akeem.g.abodunrin@intel.com
The HDMI blocks in the BCM2771 have an i2c controller to retrieve the
EDID. This block is split into two parts, the BSC and the AUTO_I2C,
lying in two separate register areas.
The AUTO_I2C block has a mailbox-like interface and will take away the
BSC control from the CPU if enabled. However, the BSC is the actually
the same controller than the one supported by the brcmstb driver, and
the AUTO_I2C doesn't really bring any immediate benefit.
Let's use the BSC then, but let's also tie the AUTO_I2C registers with a
separate compatible so that we can enable AUTO_I2C if needed in the
future.
The AUTO_I2C is enabled by default at boot though, so we first need to
release the BSC from the AUTO_I2C control.
Cc: Kamal Dasu <kdasu.kdev@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The HDMI blocks in the BCM2771 have an i2c controller to retrieve the
EDID. This block is split into two parts, the BSC and the AUTO_I2C,
lying in two separate register areas.
The AUTO_I2C block has a mailbox-like interface and will take away the
BSC control from the CPU if enabled. However, the BSC is the actually
the same controller than the one supported by the brcmstb driver, and
the AUTO_I2C doesn't really bring any immediate benefit.
We can model it in the DT as a single device with two register range,
which will allow us to use or or the other in the driver without
changing anything in the DT.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Switch the DT binding to a YAML schema to enable the DT validation.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Function 'mt7621_pcie_init_virtual_bridges' is a bit mess and can be
refactorized properly in a cleaner way. Introduce new 'pcie_rmw' inline
function helper to do clear and set the correct bits this function needs
to work.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200308091928.17177-1-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the YUV420 output from the Amlogic Meson SoCs
Video Processing Unit to the HDMI Controller.
The YUV420 is obtained by generating a YUV444 pixel stream like
the classic HDMI display modes, but then the Video Encoder output
can be configured to down-sample the YUV444 pixel stream to a YUV420
stream.
In addition if pixel stream down-sampling, the Y Cb Cr components must
also be mapped differently to align with the HDMI2.0 specifications.
This mode needs a different clock generation scheme since the TMDS PHY
clock must match the 10x ratio with the YUV420 pixel clock, but
the video encoder must run at 2x the pixel clock.
This patch enables the bridge bus format negociation, and handles
the YUV420 case if selected by the negociation.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-12-narmstrong@baylibre.com
This patch adds clocking support for the YUV420 output from the
Amlogic Meson SoCs Video Processing Unit to the HDMI Controller.
The YUV420 is obtained by generating a YUV444 pixel stream like
the classic HDMI display modes, but then the Video Encoder output
can be configured to down-sample the YUV444 pixel stream to a YUV420
stream.
This mode needs a different clock generation scheme since the TMDS PHY
clock must match the 10x ratio with the YUV420 pixel clock, but
the video encoder must run at 2x the pixel clock.
This patch adds the TMDS PHY clock value in all the video clock setup
in order to better support these specific uses cases and switch
to the Common Clock framework for clocks handling in the future.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-11-narmstrong@baylibre.com
This patch adds encoding support for the YUV420 output from the
Amlogic Meson SoCs Video Processing Unit to the HDMI Controller.
The YUV420 is obtained by generating a YUV444 pixel stream like
the classic HDMI display modes, but then the Video Encoder output
can be configured to down-sample the YUV444 pixel stream to a YUV420
stream.
In addition if pixel stream down-sampling, the Y Cb Cr components must
also be mapped differently to align with the HDMI2.0 specifications.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-10-narmstrong@baylibre.com
To allow using formats from negotiation, stop enforcing input_bus_format
in the private dw-plat-data struct.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-9-narmstrong@baylibre.com
Switch the dw-hdmi driver to drm_bridge_funcs by implementing a new local
bridge, connecting it to the dw-hdmi bridge, then implement the
atomic_get_input_bus_fmts/atomic_get_output_bus_fmts.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-8-narmstrong@baylibre.com
Before switching to bridge funcs, make sure drm_display_mode is passed
as const to the venc functions.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-7-narmstrong@baylibre.com
Now the DW-HDMI Controller supports the HDMI2.0 modes, enable support
for these modes in the connector if the platform supports them.
We limit these modes to DW-HDMI IP version >= 0x200a which
are designed to support HDMI2.0 display modes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-6-narmstrong@baylibre.com
Add the atomic_get_output_bus_fmts, atomic_get_input_bus_fmts to negociate
the possible output and input formats for the current mode and monitor,
and use the negotiated formats in a basic atomic_check callback.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-5-narmstrong@baylibre.com
Add the max_bpc property to the dw-hdmi connector to prepare support
for 10, 12 & 16bit output support.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-3-narmstrong@baylibre.com
When softsynthu device fails the register, "/dev/softsynthu" should be
printed instead of "/dev/softsynth".
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@gmail.com>
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Chris Brannon <chris@the-brannons.com>
Cc: Kirk Reiser <kirk@reisers.ca>
Link: https://lore.kernel.org/r/20200305072151.403-1-zhenzhong.duan@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mac80211 is the only user of in_use to start it and should
not be true when so.
So internal toggling of this variable is not relevant.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Link: https://lore.kernel.org/r/69585034-4318-4bec-7d9b-f64a167df237@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In a recent change to the SPI subsystem in commit <bebcfd272d>
("spi: introduce `delay` field for `spi_transfer` +
spi_transfer_delay_exec()"), a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Link: https://lore.kernel.org/r/20200304074319.22107-1-sergiu.cuciurean@analog.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In a recent change to the SPI subsystem in commit <bebcfd272d>
("spi: introduce `delay` field for `spi_transfer` +
spi_transfer_delay_exec()"), a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Link: https://lore.kernel.org/r/20200304073746.19664-1-sergiu.cuciurean@analog.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a new API devm_platform_ioremap_resource() to simplify code.
Signed-off-by: chenqiwu <chenqiwu@xiaomi.com>
Tested-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use kobj_to_dev() API instead of container_of().
Signed-off-by: chenqiwu <chenqiwu@xiaomi.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add space around & operator for improving the code
readability.
Signed-off-by: Shreeya Patel <shreeya.patel23498@gmail.com>
Acked-by: Julia Lawall <julia.lawall@inria.fr>
Link: https://lore.kernel.org/r/20200308192152.26403-1-shreeya.patel23498@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
