T10-PI and FC-NVMe are not mutually exclusive. This patch removes
restrictions where if FC-NVMe is enabled T10-PI defaults to disabled.
Link: https://lore.kernel.org/r/20200226224022.24518-16-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For N2N, fc_port struct is created during report id acquisition. At
later time, the loop resync (fabric, n2n, loop) would trigger the rest
of the login using the created fc_port struct. The loop resync logic
can trigger another fc_port allocation if the 1st allocation was not
able to execute. This patch prevents the 2nd allocation trigger.
Link: https://lore.kernel.org/r/20200226224022.24518-15-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NPIV re-enable code was blocked after FW had been initialized. The
blocking check was too broad. Reduce the check to make sure if FW is
initialized or not.
Link: https://lore.kernel.org/r/20200226224022.24518-14-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
RPD information failed to display by switch cli command. This is
caused by driver failure to properly format RDP response data with
data descriptor to allow switch to parse it correctly.
Link: https://lore.kernel.org/r/20200226224022.24518-13-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For single port 28XX adapter, the second core can still run in the
background. The flash semaphore can be held by the non-active core.
This patch tell MPI FW to check for this case and clear the semaphore
from the non-active core.
Link: https://lore.kernel.org/r/20200226224022.24518-12-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Per FW request, MB 1-7 should be logged for 8002 error.
Link: https://lore.kernel.org/r/20200226224022.24518-11-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
commit e4e3a2ce95 ("scsi: qla2xxx: Add ability to autodetect SFP
type") takes a heavy handed approach to BPM (Buffer Plus Management)
enablement:
1) During hardware initialization, if an LR-capable transceiver is
recognized, the driver schedules a disruptive post-initialization
chip-reset (ISP-ABORT) to allow the BPM settings to be sent to the
firmware. This chip-reset will result in (short-term) path-loss to
all fc-rports and their attached SCSI devices.
2) LR-detection is triggered during any link-up event, resulting in a
refresh and potential chip-reset
Based on firmware-team guidance, upon LR-capable transceiver
recognition, the driver's hardware initialization code will now
re-execute firmware with the new BPM settings, then continue on with
driver initialization. To address the second issue, the driver
performs LR-capable detection upon the driver receiving a
transceiver-insertion asynchronous event from firmware. No short-term
path loss is needed with this new semantic.
Link: https://lore.kernel.org/r/20200226224022.24518-10-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Andrew Vasquez <andrewv@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes issue where current and original exchanges count
were swapped for intiator and targets.
Also fix IOCB count for current and original which were swapped.
Link: https://lore.kernel.org/r/20200226224022.24518-9-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There's no point checking flags.disable_msix_handshake in the
interrupt handler hot-path. Instead perform the check during
queue-pair instantiation and use the proper interrupt handler.
Link: https://lore.kernel.org/r/20200226224022.24518-8-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Andrew Vasquez <andrewv@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch ensures flash updates API calls return possible failure
status through BSG interface to the application.
Link: https://lore.kernel.org/r/20200226224022.24518-7-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Michael Hernandez <mhernandez@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch improved message for Secure Flash support. No
functionality has been changed.
Link: https://lore.kernel.org/r/20200226224022.24518-6-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Michael Hernandez <mhernandez@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes issue where incorrect flag was used for sending
switch commands.
Link: https://lore.kernel.org/r/20200226224022.24518-5-hmadhani@marvell.com
Fixes: e8c72ba51a ("[SCSI] qla2xxx: Use GFF_ID to check FCP-SCSI FC4 type before logging into Nx_Ports")
Fixes: a4239945b8 ("scsi: qla2xxx: Add switch command to simplify fabric discovery")
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch uses generic firmware update options for FCoE based
adapters as well to reduce code duplication.
Link: https://lore.kernel.org/r/20200226224022.24518-4-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch moves ql2xrdpenable check earlier to avoids setting
fw_option once again before exiting qla24xx_update_fw_options.
Link: https://lore.kernel.org/r/20200226224022.24518-3-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch allows sparse to verify the endianness of the arguments passed
to make_handle().
Link: https://lore.kernel.org/r/20200220043441.20504-5-bvanassche@acm.org
Cc: Roman Bolshakov <r.bolshakov@yadro.com>
Cc: Daniel Wagner <dwagner@suse.de>
Cc: Martin Wilck <mwilck@suse.com>
Cc: Quinn Tran <qutran@marvell.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes the following sparse warnings:
drivers/scsi/qla2xxx/qla_mbx.c:120:21: warning: restricted pci_channel_state_t degrades to integer
drivers/scsi/qla2xxx/qla_mbx.c:120:37: warning: restricted pci_channel_state_t degrades to integer
>From include/linux/pci.h:
enum pci_channel_state {
/* I/O channel is in normal state */
pci_channel_io_normal = (__force pci_channel_state_t) 1,
/* I/O to channel is blocked */
pci_channel_io_frozen = (__force pci_channel_state_t) 2,
/* PCI card is dead */
pci_channel_io_perm_failure = (__force pci_channel_state_t) 3,
};
Link: https://lore.kernel.org/r/20200220043441.20504-4-bvanassche@acm.org
Cc: Roman Bolshakov <r.bolshakov@yadro.com>
Cc: Martin Wilck <mwilck@suse.com>
Cc: Quinn Tran <qutran@marvell.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of changing endianness in-place, write the data in CPU endian
format in another buffer and copy that buffer back. This patch does not
change any functionality but silences some sparse endianness warnings.
Link: https://lore.kernel.org/r/20200220043441.20504-3-bvanassche@acm.org
Cc: Roman Bolshakov <r.bolshakov@yadro.com>
Cc: Martin Wilck <mwilck@suse.com>
Cc: Quinn Tran <qutran@marvell.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since the SCSI core does not reuse the tag of the SCSI command that is
being aborted by .eh_abort() before .eh_abort() has finished it is not
necessary to check from inside that callback whether or not the SCSI
command has already completed. Instead, rely on the firmware to return an
error code when attempting to abort a command that has already
completed. Additionally, rely on the firmware to return an error code when
attempting to abort an already aborted command.
In qla2x00_abort_srb(), use blk_mq_request_started() instead of
sp->completed and sp->aborted.
Link: https://lore.kernel.org/r/20200220043441.20504-2-bvanassche@acm.org
Cc: Martin Wilck <mwilck@suse.com>
Cc: Quinn Tran <qutran@marvell.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Link speed 32.0 GT/s is supported in PCIe r5.0. Add this speed to
PCIE_SPEED2STR() and PCIE_SPEED2MBS_ENC() to correctly decode it.
This is complementary to de76cda215 ("PCI: Decode PCIe 32 GT/s link
speed").
Link: https://lore.kernel.org/r/1581937984-40353-2-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pinctrl_register_mappings is called in the pdata case, however a call to
pinctrl_unregister_mappings is missing causing the mappings to be leaked
on driver unbind. Add the missing call to correct this issue.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200228154214.13916-1-ckeepax@opensource.cirrus.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
kref_init starts with the reference count at 1, which will be balanced
by the pinctrl_put in pinctrl_unregister. The additional kref_get in
pinctrl_claim_hogs will increase this count to 2 and cause the hogs to
not get freed when pinctrl_unregister is called.
Fixes: 6118714275 ("pinctrl: core: Fix pinctrl_register_and_init() with pinctrl_enable()")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200228154142.13860-1-ckeepax@opensource.cirrus.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200227185837.GA4469@embeddedor
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Contributors for this file are :
Chris Wilson <chris@chris-wilson.co.uk>
Denis Efremov <efremov@linux.com>
Jani Nikula <jani.nikula@intel.com>
Maxime Ripard <mripard@kernel.org>
Noralf Trønnes <noralf@tronnes.org>
Sam Ravnborg <sam@ravnborg.org>
Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Denis Efremov <efremov@linux.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Emmanuel Vadot <manu@FreeBSD.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200215180911.18299-2-manu@FreeBSD.org
Here are the following optimizations have been done:
- break the loop after first found requested line
- due to above, drop redundant boolean variable
- replace open coded variant of gpiochip_is_requested()
- due to above, drop redundant pointer to struct gpio_desc
- use 'unsigned int' instead of 'unsigned' for loop counter
Note, pointer to struct gpio_chip followed by pointer to struct gpio_device
is still valid, back link is not.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200225114725.839-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Oleg wrote a very informative comment, but with the removal of
proc_cleanup_work it is no longer accurate.
Rewrite the comment so that it only talks about the details
that are still relevant, and hopefully is a little clearer.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
We monitor the health of the system via periodic heartbeat pulses. The
pulses also provide the opportunity to perform garbage collection.
However, we interpret an incomplete pulse (a missed heartbeat) as an
indication that the system is no longer responsive, i.e. hung, and
perform an engine or full GPU reset. Given that the preemption
granularity can be very coarse on a system, we let the sysadmin override
our legacy timeouts which were "optimised" for desktop applications.
The heartbeat interval can be adjusted per-engine using,
/sys/class/drm/card?/engine/*/heartbeat_interval_ms
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Steve Carbonari <steven.carbonari@intel.com>
Tested-by: Steve Carbonari <steven.carbonari@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228131716.3243616-7-chris@chris-wilson.co.uk
After initialising a preemption request, we give the current resident a
small amount of time to vacate the GPU. The preemption request is for a
higher priority context and should be immediate to maintain high
quality of service (and avoid priority inversion). However, the
preemption granularity of the GPU can be quite coarse and so we need a
compromise.
The preempt timeout can be adjusted per-engine using,
/sys/class/drm/card?/engine/*/preempt_timeout_ms
and can be disabled by setting it to 0.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Steve Carbonari <steven.carbonari@intel.com>
Tested-by: Steve Carbonari <steven.carbonari@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228131716.3243616-6-chris@chris-wilson.co.uk
When we allow ourselves to sleep before a GPU reset after disabling
submission, even for a few milliseconds, gives an innocent context the
opportunity to clear the GPU before the reset occurs. However, how long
to sleep depends on the typical non-preemptible duration (a similar
problem to determining the ideal preempt-reset timeout or even the
heartbeat interval). As this seems of a hard policy decision, punt it to
userspace.
The timeout can be adjusted using
/sys/class/drm/card?/engine/*/stop_timeout_ms
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Reviewed-by: Steve Carbonari <steven.carbonari@intel.com>
Tested-by: Steve Carbonari <steven.carbonari@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228131716.3243616-5-chris@chris-wilson.co.uk
We busywait on an inflight request (one that is currently executing on
HW, and so might complete quickly) prior to setting up an interrupt and
sleeping. The trade off is that we keep an expensive CPU core busy in
order to avoid wake up latency: where that trade off should lie is best
left to the sysadmin.
The busywait mechanism can be compiled out with
./scripts/config --set-val DRM_I915_SPIN_REQUEST 0
The maximum busywait duration can be adjusted per-engine using,
/sys/class/drm/card?/engine/*/ms_busywait_duration_ns
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Steve Carbonari <steven.carbonari@intel.com>
Tested-by: Steve Carbonari <steven.carbonari@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228131716.3243616-4-chris@chris-wilson.co.uk
Execlists uses a scheduling quantum (a timeslice) to alternate execution
between ready-to-run contexts of equal priority. This ensures that all
users (though only if they of equal importance) have the opportunity to
run and prevents livelocks where contexts may have implicit ordering due
to userspace semaphores.
The timeslicing mechanism can be compiled out with
./scripts/config --set-val DRM_I915_TIMESLICE_DURATION 0
The timeslice duration can be adjusted per-engine using,
/sys/class/drm/card?/engine/*/timeslice_duration_ms
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Steve Carbonari <steven.carbonari@intel.com>
Tested-by: Steve Carbonari <steven.carbonari@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228131716.3243616-3-chris@chris-wilson.co.uk
Use the per-engine sysfs directory to let userspace discover the
mmio_base of each engine. Prior to recent generations, the user
accessible registers on each engine are at a fixed offset relative to
each engine -- but require absolute addressing. As the absolute address
depends on the actual physical engine, this is not always possible to
determine from userspace (for example icl may expose vcs1 or vcs2 as the
second vcs engine). Make this easy for userspace to discover by
providing the mmio_base in sysfs.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Steve Carbonari <steven.carbonari@intel.com>
Tested-by: Steve Carbonari <steven.carbonari@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228131716.3243616-2-chris@chris-wilson.co.uk
Preliminary stub to add engines underneath /sys/class/drm/cardN/, so
that we can expose properties on each engine to the sysadmin.
To start with we have basic analogues of the i915_query ioctl so that we
can pretty print engine discovery from the shell, and flesh out the
directory structure. Later we will add writeable sysadmin properties such
as per-engine timeout controls.
An example tree of the engine properties on Braswell:
/sys/class/drm/card0
└── engine
├── bcs0
│ ├── capabilities
│ ├── class
│ ├── instance
│ ├── known_capabilities
│ └── name
├── rcs0
│ ├── capabilities
│ ├── class
│ ├── instance
│ ├── known_capabilities
│ └── name
├── vcs0
│ ├── capabilities
│ ├── class
│ ├── instance
│ ├── known_capabilities
│ └── name
└── vecs0
├── capabilities
├── class
├── instance
├── known_capabilities
└── name
v2: Include stringified capabilities
v3: Include all known capabilities for futureproofing.
v4: Combine the two caps loops into one
v5: Hide underneath Kconfig.unstable for wider discussion
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Tested-by: Steve Carbonari <steven.carbonari@intel.com>
Reviewed-by: Steve Carbonari <steven.carbonari@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228131716.3243616-1-chris@chris-wilson.co.uk
This adds a message lock to the smu_send_smc_msg* implementations to
protect against concurrent access to the mmu registers used to
communicate with the SMU
v2: Implement for smu_v12_0 as well
v3: Add mutex_init for message_lock
Signed-off-by: Matt Coffin <mcoffin13@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The new interface reads the argument in the call to send the message, so
this is no longer needed, and shouldn't be used for concurrency safety
reasons.
Signed-off-by: Matt Coffin <mcoffin13@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move the responsibility for reading argument registers into the
smu_send_smc_msg* implementations, so that adding a message-sending lock
to protect the SMU registers will result in the lock still being held
when the argument is read.
v2: transition smu_v12_0, it's asics, and vega20
Signed-off-by: Matt Coffin <mcoffin13@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dc to pplib interface is changed for navi1x, renoir.
display_config_changed is not called by dc anymore.
smu_write_watermarks_table is not executed for navi1x, renoir
during boot up.
solution: call smu_write_watermarks_table just after dc pass
watermark clock settings to pplib
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
SPM_VMID is a global resource, SPM access the video memory according to
SPM_VMID. The initial valude of SPM_VMID is 0 which is used by kernel.
That means UMD can overwrite the memory of VMID0 by enabling SPM, that
is really dangerous.
Initialize SPM_VMID with 0xf, it messes up other user mode process at
most.
v2: squash in indentation fix
Signed-off-by: Jacob He <jacob.he@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For vega10 sriov, the register is blocked, use
copy data command to fix the issue.
v2: Rename amdgpu_kiq_read_clock to gfx_v9_0_kiq_read_clock.
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
SDMA MQD memory type is NC that causes MQD data overwritten
accidentally by an old stable cache line. Changing it to UC
default for GART will fix the issue.
The mqd_gfx9 parameter is meant for control stacks that are
allocated together with user mode queue MQDs. Setting
mqd_gfx9 to true maps the control stack pages as NC.
Here it was accidentally applied to SDMA MQDs,
which are allocated together with the HIQ MQD. Setting
the mqd_gfx9 to false avoids that.
Signed-off-by: Eric Huang <jinhuieric.huang@amd.com>
Acked-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Given we can query all the asic specific information from amdgpu_gfx_config,
we can make get_tile_config() generic.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The two members will be used by KFD later.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The assert_mmap_offset() returns type bool so if we return an error
pointer that is "return true;" or success. If we have an error, then
we should return false.
Fixes: 3d81d589d6 ("drm/i915: Test exhaustion of the mmap space")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228141413.qfjf4abr323drlo4@kili.mountain
Fix all the warnings in the DT binding schema examples when built with
'W=1'. This is in preparation to make that the default for examples.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
