'eth_zero_addr()' is already called in the error handling path. This is
harmless, but there is no point in calling it twice, so remove one.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
When used in Extended SPI mode on LS1021A, the DSPI controller wants to
have the least significant 16-bit word written first to the TX FIFO.
In fact, the LS1021A reference manual says:
33.5.2.4.2 Draining the TX FIFO
When Extended SPI Mode (DSPIx_MCR[XSPI]) is enabled, if the frame size
of SPI Data to be transmitted is more than 16 bits, then it causes two
Data entries to be popped from TX FIFO simultaneously which are
transferred to the shift register. The first of the two popped entries
forms the 16 least significant bits of the SPI frame to be transmitted.
So given the following TX buffer:
+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+
| 0x0 | 0x1 | 0x2 | 0x3 | 0x4 | 0x5 | 0x6 | 0x7 | 0x8 | 0x9 | 0xa | 0xb |
+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+
| 32-bit word 1 | 32-bit word 2 | 32-bit word 3 |
+-----------------------+-----------------------+-----------------------+
The correct way that a little-endian system should transmit it on the
wire when bits_per_word is 32 is:
0x03020100
0x07060504
0x0b0a0908
But it is actually transmitted as following, as seen with a scope:
0x01000302
0x05040706
0x09080b0a
It appears that this patch has been submitted at least once before:
https://lkml.org/lkml/2018/9/21/286
but in that case Chuanhua Han did not manage to explain the problem
clearly enough and the patch did not get merged, leaving XSPI mode
broken.
Fixes: 8fcd151d26 ("spi: spi-fsl-dspi: XSPI FIFO handling (in TCFQ mode)")
Cc: Esben Haabendal <eha@deif.com>
Cc: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20191228135536.14284-1-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
When system wide suspend happens, ACP will be powered off
and when system resumes,for audio usecase to continue,all
the runtime configuration data needs to be programmed again.
Added resume pm call back to ACP pm ops and also added runtime
PM operations for ACP3x PCM platform device.
Device will enter into D3 state when there is no activity
on audio I2S lines.
Signed-off-by: Ravulapati Vishnu vardhan rao <Vishnuvardhanrao.Ravulapati@amd.com>
Link: https://lore.kernel.org/r/1577540460-21438-6-git-send-email-Vishnuvardhanrao.Ravulapati@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds I2S SP support in ACP PCM DMA and DAI.
Added I2S support in DMA and DAI probe,its hw_params handling
its open and close functionalities.
This enables to open and close on the SP instance for
playback and capture.
Signed-off-by: Ravulapati Vishnu vardhan rao <Vishnuvardhanrao.Ravulapati@amd.com>
Link: https://lore.kernel.org/r/1577540460-21438-3-git-send-email-Vishnuvardhanrao.Ravulapati@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC: PCM DMA driver should only have dma ops.
So Removed all DAI related functionality.Refactoring
the PCM DMA diver code.Added new file containing only DAI ops
Signed-off-by: Ravulapati Vishnu vardhan rao <Vishnuvardhanrao.Ravulapati@amd.com>
Link: https://lore.kernel.org/r/1577540460-21438-2-git-send-email-Vishnuvardhanrao.Ravulapati@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If 'madera_init_bus_error_irq()' fails,
'wm_adsp2_remove(&cs47l92->core.adsp[0])' will be called twice.
Once in the 'if' block, and once in the error handling path.
This is harmless, but one of this call can be axed.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20191226162907.9490-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
As per 802.3-2005, Section Two, Annex 28B, Table 28B-2 [1], when
_only_ Rx pause is enabled, both symmetric and asymmetric pause
towards local device must be enabled. Also, firmware returns the local
device's flow control pause params as part of advertised capabilities
and negotiated params as part of current link attributes. So, fix up
ethtool's flow control pause params fetch logic to read from acaps,
instead of linkattr.
[1] https://standards.ieee.org/standard/802_3-2005.html
Fixes: c3168cabe1 ("cxgb4/cxgbvf: Handle 32-bit fw port capabilities")
Signed-off-by: Surendra Mobiya <surendra@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Remove #ifdef pollution around nf_ingress(), from Lukas Wunner.
2) Document ingress hook in netdevice, also from Lukas.
3) Remove htons() in tunnel metadata port netlink attributes,
from Xin Long.
4) Missing erspan netlink attribute validation also from Xin Long.
5) Missing erspan version in tunnel, from Xin Long.
6) Missing attribute nest in NFTA_TUNNEL_KEY_OPTS_{VXLAN,ERSPAN}
Patch from Xin Long.
7) Missing nla_nest_cancel() in tunnel netlink dump path,
from Xin Long.
8) Remove two exported conntrack symbols with no clients,
from Florian Westphal.
9) Add nft_meta_get_eval_time() helper to nft_meta, from Florian.
10) Add nft_meta_pkttype helper for loopback, also from Florian.
11) Add nft_meta_socket uid helper, from Florian Westphal.
12) Add nft_meta_cgroup helper, from Florian.
13) Add nft_meta_ifkind helper, from Florian.
14) Group all interface related meta selector, from Florian.
15) Add nft_prandom_u32() helper, from Florian.
16) Add nft_meta_rtclassid helper, from Florian.
17) Add support for matching on the slave device index,
from Florian.
This batch, among other things, contains updates for the netfilter
tunnel netlink interface: This extension is still incomplete and lacking
proper userspace support which is actually my fault, I did not find the
time to go back and finish this. This update is breaking tunnel UAPI in
some aspects to fix it but do it better sooner than never.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A few uapi/sound/*.h headers have been corrected for recovering from
the compile errors with the existing user-space code (alsa-lib) by the
recent commits. OTOH, these introduced another regression, as now
linux/types.h inclusion became mandatory for the uapi header checks.
As a compromise, this patch re-adds linux/types.h inclusions again,
but conditionally not to break other non-standard user-space stuff
again.
Fixes: 2e46886763 ("ALSA: emu10k1: Make uapi/emu10k1.h compilable again")
Fixes: d63e63d421 ("ALSA: hdsp: Make uapi/hdsp.h compilable again")
Fixes: 4fa406caf9 ("ALSA: hdspm: Drop linux/types.h inclusion in uapi header")
Reported-by: kbuild test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20191230212742.28925-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Do not reset RING_BB_STATE, leaving it to the default state value. This
prevents bdw/bsw from getting confused when executing batches from the
GGTT.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191230165821.3840449-2-chris@chris-wilson.co.uk
Now that all callers of FIELD_SIZEOF() have been converted to
sizeof_field(), remove the unused prior macro.
Signed-off-by: Kees Cook <keescook@chromium.org>
This converts the USB3503 to pick GPIO descriptors from the
device tree instead of iteratively picking out GPIO number
references and then referencing these from the global GPIO
numberspace.
The USB3503 is only used from device tree among the in-tree
platforms. If board files would still desire to use it they can
provide machine descriptor tables.
Make sure to preserve semantics such as the reset delay
introduced by Stefan.
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[mszyprow: invert the logic behind reset GPIO line]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20191211145226.25074-1-m.szyprowski@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current USB3503 driver ignores GPIO polarity and always operates as if the
GPIO lines were flagged as ACTIVE_HIGH. Fix the polarity for the existing
USB3503 chip applications to match the chip specification and common
convention for naming the pins. The only pin, which has to be ACTIVE_LOW
is the reset pin. The remaining are ACTIVE_HIGH. This change allows later
to fix the USB3503 driver to properly use generic GPIO bindings and read
polarity from DT.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20191211145208.24976-1-m.szyprowski@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Renesas USBHS driver includes a bit of surplus headers
and uses the old GPIO API so let's switch it to use the
GPIO descriptor.
I noticed that the enable_gpio inside renesas_usbhs_driver_param
isn't really referenced anywhere, and it is also the wrong
type (u32) so let's just delete it and use a local variable
instead.
Cc: Eugeniu Rosca <erosca@de.adit-jv.com>
Cc: Veeraiyan Chidambaram <veeraiyan.chidambaram@in.bosch.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191217141241.57639-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of the USB phy drivers can be compile tested to increase build
coverage.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20191230172215.17370-2-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of the USB host drivers can be compile tested to increase build
coverage. Add 'if' conditional to 'default y' so they will not get
enabled by default on all other architectures.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20191230172215.17370-1-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To support evaluating 64-bit kernel mode instructions:
* Replace existing checks for user_64bit_mode() with a new helper that
checks whether code is being executed in either 64-bit kernel mode or
64-bit user mode.
* Select the GS base depending on whether the instruction is being
evaluated in kernel mode.
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: "Gustavo A. R. Silva" <gustavo@embeddedor.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: kasan-dev@googlegroups.com
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Sean Christopherson <sean.j.christopherson@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20191218231150.12139-1-jannh@google.com
CCGx controller used on NVIDIA GPU card has two separate display
altmode for two DP pin assignments. UCSI specification doesn't
prohibits using separate display altmode.
Current UCSI Type-C framework expects only one display altmode for
all DP pin assignment. This patch squashes two separate display
altmode into single altmode to support controllers with separate
display altmode. We first read all the alternate modes of connector
and then run through it to know if there are separate display
altmodes. If so, it prepares a new port altmode set after squashing
two or more separate altmodes into one.
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20191230133431.63445-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver needs to ignore any Connector Change Events
before the Connector Change Indication notifications have
actually been enabled. This adds a check to
ucsi_connector_change() function to make sure the function
does not try to process the event unless the Connector
Change notifications have been enabled.
It is quite common that the firmware representing the "PPM"
(Platform Policy Manager) starts generating Connector Change
notifications even when only the Command Completion
notifications are enabled.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20191230133431.63445-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mtk-xhci platform glue sets the DMA mask to 32 bits on its own,
which was needed before commit fda182d80a ("usb: xhci: configure
32-bit DMA if the controller does not support 64-bit DMA"), but now it
has no effect, because xhci_gen_setup() sets it up for us according to
hardware capabilities. Remove the useless code.
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Link: https://lore.kernel.org/r/20191219093954.163417-1-tfiga@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AB8505 supports an "UART carkit mode" which makes UART accessible
through the USB connector. Upon detection of the UART cable,
this mode has to be manually enabled by:
1. Turning on the PHY in peripheral mode
2. Reconfiguring PHY/pins to route UART signals to USB pins
At the moment, we do not handle the UART link statuses at all,
which means that UART stops working as soon as phy-ab8500-usb is loaded
(since we disable the PHY after initialization).
Keeping UART working if the cable is inserted before turning on the device
is quite simple: In this case, early boot firmware has already set up
the necessary PHY/pin configuration. The presence of the UART cable
is reported by a special value in the USB link status register.
We can check for that value in ab8505_usb_link_status_update()
and set the PHY back to peripheral mode to restore UART.
(Note: This will result in some minor garbage since we still
temporarily disable the PHY during initialization...)
Fully implementing this feature is more complicated:
For some reason, AB8505 does not update UART link status after bootup.
Regular USB cables work fine, but the link status register does not change
its state if an UART cable is inserted/removed.
It seems likely that the hardware is not actually capable of detecting
UART cables autonomously. In addition to the USB link status register,
implementations in the vendor kernel also manually measure
the ID resistance to detect additional cable types. For UART cables,
the USB link status register might simply reflect the PHY configuration
instead of the actual link status.
Implementing that functionality requires significant additions,
so for now just implement the simple case. This allows using UART
when inserting the cable before turning on the device.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191218203450.71037-1-stephan@gerhold.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some special dance is needed to initialize the HSIC port.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20191221065008.266445-2-lkundrak@v3.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is merely a cleanup. None of these is used anywhere.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20191221065008.266445-4-lkundrak@v3.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We may be using a NOP transceiver and those are treated specially by the
USB core and return -ENODEV with devm_phy_get().
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20191221065008.266445-3-lkundrak@v3.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On shutdown, ehci_power_off() is called unconditionally to power off
each port, even if it was never called to power on the port.
For chipidea, this results in a call to ehci_ci_portpower() with a request
to power off ports even if the port was never powered on.
This results in the following warning from the regulator code.
WARNING: CPU: 0 PID: 182 at drivers/regulator/core.c:2596 _regulator_disable+0x1a8/0x210
unbalanced disables for usb_otg2_vbus
Modules linked in:
CPU: 0 PID: 182 Comm: init Not tainted 5.4.6 #1
Hardware name: Freescale i.MX7 Dual (Device Tree)
[<c0313658>] (unwind_backtrace) from [<c030d698>] (show_stack+0x10/0x14)
[<c030d698>] (show_stack) from [<c1133afc>] (dump_stack+0xe0/0x10c)
[<c1133afc>] (dump_stack) from [<c0349098>] (__warn+0xf4/0x10c)
[<c0349098>] (__warn) from [<c0349128>] (warn_slowpath_fmt+0x78/0xbc)
[<c0349128>] (warn_slowpath_fmt) from [<c09f36ac>] (_regulator_disable+0x1a8/0x210)
[<c09f36ac>] (_regulator_disable) from [<c09f374c>] (regulator_disable+0x38/0xe8)
[<c09f374c>] (regulator_disable) from [<c0df7bac>] (ehci_ci_portpower+0x38/0xdc)
[<c0df7bac>] (ehci_ci_portpower) from [<c0db4fa4>] (ehci_port_power+0x50/0xa4)
[<c0db4fa4>] (ehci_port_power) from [<c0db5420>] (ehci_silence_controller+0x5c/0xc4)
[<c0db5420>] (ehci_silence_controller) from [<c0db7644>] (ehci_stop+0x3c/0xcc)
[<c0db7644>] (ehci_stop) from [<c0d5bdc4>] (usb_remove_hcd+0xe0/0x19c)
[<c0d5bdc4>] (usb_remove_hcd) from [<c0df7638>] (host_stop+0x38/0xa8)
[<c0df7638>] (host_stop) from [<c0df2f34>] (ci_hdrc_remove+0x44/0xe4)
...
Keeping track of the power enable state avoids the warning and traceback.
Fixes: c8679a2fb8 ("usb: chipidea: host: add portpower override")
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Cc: Peter Chen <peter.chen@freescale.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20191226155754.25451-1-linux@roeck-us.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kernel enforcement statement is a important statement to show a kind of
attitude in kernel community. This patch translate it into Chinese and
add it into toctree.
Signed-off-by: Alex Shi <alex.shi@linux.alibaba.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Li Zefan <lizefan@huawei.com>
Cc: Harry Wei <harryxiyou@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/1576811085-30544-3-git-send-email-alex.shi@linux.alibaba.com
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Embargoed hardware issues is a necessary process guide, but leak of
Chinese version, since there is more Chinese hardware vendors in market.
We'd better have a Chinese version of this guide.
This patch translate the guide, add it into toctree. and also add a link
stub for the original doc.
Signed-off-by: Alex Shi <alex.shi@linux.alibaba.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: lizefan@huawei.com
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Harry Wei <harryxiyou@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Sasha Levin <sashal@kernel.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: linux-doc@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/1576811085-30544-1-git-send-email-alex.shi@linux.alibaba.com
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The IRQ handler was passed a pointer to a struct dma_controller, but the
argument was then casted to a pointer to a struct musb_dma_controller.
Fixes: 427c4f3334 ("usb: struct device - replace bus_id with dev_name(), dev_set_name()")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20191216161844.772-2-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid printing any error message if the error code is -EPROBE_DEFER.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20191216162432.1256-1-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this, this new driver fails to link:
drivers/usb/gadget/udc/tegra-xudc.o: In function `tegra_xudc_remove':
tegra-xudc.c:(.text+0x19d4): undefined reference to `usb_role_switch_unregister'
drivers/usb/gadget/udc/tegra-xudc.o: In function `tegra_xudc_probe':
tegra-xudc.c:(.text+0x2a34): undefined reference to `usb_role_switch_register'
drivers/usb/gadget/udc/tegra-xudc.o: In function `tegra_xudc_usb_role_sw_work':
tegra-xudc.c:(.text+0x4b64): undefined reference to `usb_role_switch_get_role'
Fixes: 49db427232 ("usb: gadget: Add UDC driver for tegra XUSB device mode controller")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20191216131831.3228566-1-arnd@arndb.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Amend the endpoint-descriptor sanity checks to detect all duplicate
endpoint addresses in a configuration.
Commit 0a8fd13462 ("USB: fix problems with duplicate endpoint
addresses") added a check for duplicate endpoint addresses within a
single alternate setting, but did not look for duplicate addresses in
other interfaces.
The current check would also not detect all duplicate addresses when one
endpoint is as a (bi-directional) control endpoint.
This specifically avoids overwriting the endpoint entries in struct
usb_device when enabling a duplicate endpoint, something which could
potentially lead to crashes or leaks, for example, when endpoints are
later disabled.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20191219161016.6695-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the serial device is disconnected and reconnected, it re-enumerates
properly but does not link it. fwiw, linking means just saving the port
index, so allow it always as there is no harm in saving the same value
again even if it tries to relink with the same port.
Fixes: fb2b90014d ("tty: link tty and port before configuring it as console")
Reported-by: Kenneth R. Crudup <kenny@panix.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191227174434.12057-1-sudipm.mukherjee@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A system that supports resource monitoring may have multiple resources
while not all of these resources are capable of monitoring. Monitoring
related state is initialized only for resources that are capable of
monitoring and correspondingly this state should subsequently only be
removed from these resources that are capable of monitoring.
domain_add_cpu() calls domain_setup_mon_state() only when r->mon_capable
is true where it will initialize d->mbm_over. However,
domain_remove_cpu() calls cancel_delayed_work(&d->mbm_over) without
checking r->mon_capable resulting in an attempt to cancel d->mbm_over on
all resources, even those that never initialized d->mbm_over because
they are not capable of monitoring. Hence, it triggers a debugobjects
warning when offlining CPUs because those timer debugobjects are never
initialized:
ODEBUG: assert_init not available (active state 0) object type:
timer_list hint: 0x0
WARNING: CPU: 143 PID: 789 at lib/debugobjects.c:484
debug_print_object
Hardware name: HP Synergy 680 Gen9/Synergy 680 Gen9 Compute Module, BIOS I40 05/23/2018
RIP: 0010:debug_print_object
Call Trace:
debug_object_assert_init
del_timer
try_to_grab_pending
cancel_delayed_work
resctrl_offline_cpu
cpuhp_invoke_callback
cpuhp_thread_fun
smpboot_thread_fn
kthread
ret_from_fork
Fixes: e33026831b ("x86/intel_rdt/mbm: Handle counter overflow")
Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: john.stultz@linaro.org
Cc: sboyd@kernel.org
Cc: <stable@vger.kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: tj@kernel.org
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vikas Shivappa <vikas.shivappa@linux.intel.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20191211033042.2188-1-cai@lca.pw
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Vinod Koul <vkoul@kernel.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
