This enables the Gigabit Ethernet support on the Raspberry Pi 4.
The defined PHY mode is equivalent to the default register settings
in the downstream tree.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
arm64 places the CMA in ZONE_DMA32, which is not good enough for the
Raspberry Pi 4 since it contains peripherals that can only address the
first GB of memory. Explicitly place the CMA into that area.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Variable "rate" already contains the current clock rate, so use that
rather than calling clk_get_rate() again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
One of the obvious use cases for these commands is networking, where
it's not uncommon to have tons of sockets open and polled for. The
current implementation uses a list for insertion and lookup, which works
fine for file based use cases where the count is usually low, it breaks
down somewhat for higher number of files / sockets. A test case with
30k sockets being polled for and cancelled takes:
real 0m6.968s
user 0m0.002s
sys 0m6.936s
with the patch it takes:
real 0m0.233s
user 0m0.010s
sys 0m0.176s
If you go to 50k sockets, it gets even more abysmal with the current
code:
real 0m40.602s
user 0m0.010s
sys 0m40.555s
with the patch it takes:
real 0m0.398s
user 0m0.000s
sys 0m0.341s
Change is pretty straight forward, just replace the cancel_list with
a red/black tree instead.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Before this patch, function gfs2_freeze would loop forever if the
filesystem it tries to freeze is withdrawn. That's because function
gfs2_lock_fs_check_clean tries to enqueue the glock of the journal and
the gfs2_glock returns -EIO because you can't enqueue a journaled glock
after a withdraw.
Move the check for file system withdraw inside the loop so that the loop
can end when withdraw occurs.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Before this patch, an IO error encountered in function gfs2_ail1_flush
would cause a deadlock: because of the io error (and its resulting
withdrawn state), buffers stopped being written to the journal.
Buffers would remain on the ail1 list, so gfs2_ail1_start_one would
return 1 to indicate dirty buffers were still on the ail1 list.
However, when function gfs2_ail1_flush got a non-zero return code,
it would goto restart to retry the writes, which meant it would never
finish, and thus the infinite loop.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Add function gfs2_withdrawn and replace all checks for the SDF_WITHDRAWN
bit to call it. This does not change the logic or function of gfs2, and
it facilitates later improvements to the withdraw sequence.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
There was a stray tab in the help text of the aforementioned config
option which showed like this:
The "print fmt" of the trace events will show the enum/sizeof names
instead of their values. This can cause problems for user space tools
...
in menuconfig. Remove it and end a sentence with a fullstop.
No functional changes.
Link: http://lkml.kernel.org/r/20191112174219.10933-1-bp@alien8.de
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Without this, buffers can be printed with __print_array macro that has
no formatting options and can be hard to read. The other way is to
mimic formatting capability with multiple calls of trace event with one
call per row which gives performance impact and different timestamp in
each row.
Link: http://lkml.kernel.org/r/1573130738-29390-2-git-send-email-piotrx.maziarz@linux.intel.com
Signed-off-by: Piotr Maziarz <piotrx.maziarz@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Provided function is an analogue of print_hex_dump().
Implementing this function in seq_buf allows using for multiple
purposes (e.g. for tracing) and therefore prevents from code duplication
in every layer that uses seq_buf.
print_hex_dump() is an essential part of logging data to dmesg. Adding
similar capability for other purposes is beneficial to all users.
Example usage:
seq_buf_hex_dump(seq, "", DUMP_PREFIX_OFFSET, 16, 4, buf,
ARRAY_SIZE(buf), true);
Example output:
00000000: 00000000 ffffff10 ffffff32 ffff3210 ........2....2..
00000010: ffff3210 83d00437 c0700000 00000000 .2..7.....p.....
00000020: 02010004 0000000f 0000000f 00004002 .............@..
00000030: 00000fff 00000000 ........
Link: http://lkml.kernel.org/r/1573130738-29390-1-git-send-email-piotrx.maziarz@linux.intel.com
Signed-off-by: Piotr Maziarz <piotrx.maziarz@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Check whether the non-suffixed symbol is notrace, since suffixed
symbols are generated by the compilers for optimization. Based on
these suffixed symbols, notrace check might not work because
some of them are just a partial code of the original function.
(e.g. cold-cache (unlikely) code is separated from original
function as FUNCTION.cold.XX)
For example, without this fix,
# echo p device_add.cold.67 > /sys/kernel/debug/tracing/kprobe_events
sh: write error: Invalid argument
# cat /sys/kernel/debug/tracing/error_log
[ 135.491035] trace_kprobe: error: Failed to register probe event
Command: p device_add.cold.67
^
# dmesg | tail -n 1
[ 135.488599] trace_kprobe: Could not probe notrace function device_add.cold.67
With this,
# echo p device_add.cold.66 > /sys/kernel/debug/tracing/kprobe_events
# cat /sys/kernel/debug/kprobes/list
ffffffff81599de9 k device_add.cold.66+0x0 [DISABLED]
Actually, kprobe blacklist already did similar thing,
see within_kprobe_blacklist().
Link: http://lkml.kernel.org/r/157233790394.6706.18243942030937189679.stgit@devnote2
Fixes: 45408c4f92 ("tracing: kprobes: Prohibit probing on notrace function")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Fail to allocate memory for tgid_map, because it requires order-6 page.
detail as:
c3 sh: page allocation failure: order:6,
mode:0x140c0c0(GFP_KERNEL), nodemask=(null)
c3 sh cpuset=/ mems_allowed=0
c3 CPU: 3 PID: 5632 Comm: sh Tainted: G W O 4.14.133+ #10
c3 Hardware name: Generic DT based system
c3 Backtrace:
c3 [<c010bdbc>] (dump_backtrace) from [<c010c08c>](show_stack+0x18/0x1c)
c3 [<c010c074>] (show_stack) from [<c0993c54>](dump_stack+0x84/0xa4)
c3 [<c0993bd0>] (dump_stack) from [<c0229858>](warn_alloc+0xc4/0x19c)
c3 [<c0229798>] (warn_alloc) from [<c022a6e4>](__alloc_pages_nodemask+0xd18/0xf28)
c3 [<c02299cc>] (__alloc_pages_nodemask) from [<c0248344>](kmalloc_order+0x20/0x38)
c3 [<c0248324>] (kmalloc_order) from [<c0248380>](kmalloc_order_trace+0x24/0x108)
c3 [<c024835c>] (kmalloc_order_trace) from [<c01e6078>](set_tracer_flag+0xb0/0x158)
c3 [<c01e5fc8>] (set_tracer_flag) from [<c01e6404>](trace_options_core_write+0x7c/0xcc)
c3 [<c01e6388>] (trace_options_core_write) from [<c0278b1c>](__vfs_write+0x40/0x14c)
c3 [<c0278adc>] (__vfs_write) from [<c0278e10>](vfs_write+0xc4/0x198)
c3 [<c0278d4c>] (vfs_write) from [<c027906c>](SyS_write+0x6c/0xd0)
c3 [<c0279000>] (SyS_write) from [<c01079a0>](ret_fast_syscall+0x0/0x54)
Switch to use kvcalloc to avoid unexpected allocation failures.
Link: http://lkml.kernel.org/r/1571888070-24425-1-git-send-email-chunyan.zhang@unisoc.com
Signed-off-by: Yuming Han <yuming.han@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Comparator function type, cmp_func_t, is defined in the types.h,
use it in bsearch() and, thus, add more sense to the corresponding
comment in the code.
Link: http://lkml.kernel.org/r/20191007135656.37734-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The function types for swap, cmp and cmp_r functions are already
being in use by modules.
Move them to types.h that everybody in kernel will be able to use
generic types instead of custom ones.
This adds more sense to the comment in bsearch() later on.
Link: http://lkml.kernel.org/r/20191007135656.37734-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
As the ftrace selftests can run for a long period of time, disable the
timeout that the general selftests have. If a selftest hangs, then it
probably means the machine will hang too.
Link: https://lore.kernel.org/r/alpine.LSU.2.21.1911131604170.18679@pobox.suse.cz
Suggested-by: Miroslav Benes <mbenes@suse.cz>
Tested-by: Miroslav Benes <mbenes@suse.cz>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The C compiler is allowing more checks to make sure that function pointers
are assigned to the correct prototype function. Unfortunately, the function
graph tracer uses a special name with its assigned ftrace_graph_return
function pointer that maps to a stub function used by the function tracer
(ftrace_stub). The ftrace_graph_return variable is compared to the
ftrace_stub in some archs to know if the function graph tracer is enabled or
not. This means we can not just simply create a new function stub that
compares it without modifying all the archs.
Instead, have the linker script create a function_graph_stub that maps to
ftrace_stub, and this way we can define the prototype for it to match the
prototype of ftrace_graph_return, and make the compiler checks all happy!
Link: http://lkml.kernel.org/r/20191015090055.789a0aed@gandalf.local.home
Cc: linux-sh@vger.kernel.org
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Reported-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The workaround to disable coarse power gating is still needed on SKL
GT3/GT4 machines and since the RC6 context corruption was discovered by
the hardware team also on all GEN9 machines. Restore applying the
workaround.
Fixes: c113236718 ("drm/i915: Extract GT render sleep (rc6) management")
Testcase: igt/intel_gt_pm_late_selftests/live_rc6_ctx
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Andi Shyti <andi.shyti@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191114152621.7235-1-imre.deak@intel.com
Some versions of gcc (so far 6.3 and 7.4) throw a warning:
drivers/block/rbd.c: In function 'rbd_object_map_callback':
drivers/block/rbd.c:2124:21: warning: 'current_state' may be used uninitialized in this function [-Wmaybe-uninitialized]
(current_state == OBJECT_EXISTS && state == OBJECT_EXISTS_CLEAN))
drivers/block/rbd.c:2092:23: note: 'current_state' was declared here
u8 state, new_state, current_state;
^~~~~~~~~~~~~
It's bogus because all current_state accesses are guarded by
has_current_state.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Dongsheng Yang <dongsheng.yang@easystack.cn>
This device presents itself as a USB hub with three attached devices:
- An ACM serial port connected to the GPS module (not affected by this
commit)
- An FTDI serial port connected to the GPS module (1546:0502)
- Another FTDI serial port connected to the ODIN-W2 radio module
(1546:0503)
This commit registers U-Blox's VID and the PIDs of the second and third
devices.
Datasheet: https://www.u-blox.com/sites/default/files/C099-F9P-AppBoard-Mbed-OS3-FW_UserGuide_%28UBX-18063024%29.pdf
Signed-off-by: Fabio D'Urso <fabiodurso@hotmail.it>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
HDMI_PICTURE_ASPECT_NONE is zero and the connector state is kzalloc()'d
so no need to initialize conn_state->picture_aspect_ratio with it.
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190620142639.17518-6-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
HDMI_PICTURE_ASPECT_NONE means "Automatic" so when the user has that
selected we should keep whatever aspect ratio the mode already has.
Also no point in checking for connector->is_hdmi in the SDVO code
since we only attach the property to HDMI connectors.
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190620142639.17518-5-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Ceph can in some cases issue an async DIO request, in which case we can
end up calling ceph_end_io_direct before the I/O is actually complete.
That may allow buffered operations to proceed while DIO requests are
still in flight.
Fix this by incrementing the i_dio_count when issuing an async DIO
request, and decrement it when tearing down the aio_req.
Fixes: 321fe13c93 ("ceph: add buffered/direct exclusionary locking for reads and writes")
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Most of the time, we (or the vfs layer) takes the inode_lock and then
acquires caps, but ceph_read_iter does the opposite, and that can lead
to a deadlock.
When there are multiple clients treading over the same data, we can end
up in a situation where a reader takes caps and then tries to acquire
the inode_lock. Another task holds the inode_lock and issues a request
to the MDS which needs to revoke the caps, but that can't happen until
the inode_lock is unwedged.
Fix this by having ceph_read_iter take the inode_lock earlier, before
attempting to acquire caps.
Fixes: 321fe13c93 ("ceph: add buffered/direct exclusionary locking for reads and writes")
Link: https://tracker.ceph.com/issues/36348
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
As we want to be able to run inside atomic context for retiring the
i915_active, and we are no longer allowed to abuse mutex_trylock, split
the tree management portion of i915_active.mutex into an irq-safe
spinlock.
References: a0855d24fc ("locking/mutex: Complain upon mutex API misuse in IRQ contexts")
References: https://bugs.freedesktop.org/show_bug.cgi?id=111626
Fixes: 274cbf20fd ("drm/i915: Push the i915_active.retire into a worker")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191114172535.1116-1-chris@chris-wilson.co.uk
Probe the mocs registers for new contexts and across GPU resets. Similar
to intel_workarounds, we have tables of what register values we expect
to see, so verify that user contexts are affected by them. In the
future, we should add tests similar to intel_sseu to cover dynamic
reconfigurations.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Prathap Kumar Valsan <prathap.kumar.valsan@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Prathap Kumar Valsan <prathap.kumar.valsan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191112223600.30993-4-chris@chris-wilson.co.uk
We repeatedly (and more so in future) use the same looping construct
over the mocs definition table to setup the register state. Refactor the
loop construct into a reusable macro.
add/remove: 2/1 grow/shrink: 1/2 up/down: 113/-330 (-217)
Function old new delta
intel_mocs_init_engine.cold - 71 +71
offset - 28 +28
__func__ 17273 17287 +14
intel_mocs_init 143 113 -30
mocs_register.isra 91 - -91
intel_mocs_init_engine 503 294 -209
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191112223600.30993-3-chris@chris-wilson.co.uk
Be consistent in our mocs setup on Tigerlake and set the unused control
value to follow the PTE entry as we previously have done. The unused
values are beyond the defines of the ABI, the consistency simplifies our
checking.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191112223600.30993-1-chris@chris-wilson.co.uk
... or let function calls stick out and thus remain on a single line,
even if the 80 cols rule is violated by a couple of chars, for better
readability.
No functional changes.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: x86@kernel.org
Link: https://lkml.kernel.org/r/20191114172200.19563-1-bp@alien8.de
When the crashkernel kernel command line option is specified, the low
1M memory will always be reserved now. Therefore, it's not necessary to
create a backup region anymore and also no need to copy the contents of
the first 640k to it.
Remove all the code related to handling that backup region.
[ bp: Massage commit message. ]
Signed-off-by: Lianbo Jiang <lijiang@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: bhe@redhat.com
Cc: Dave Young <dyoung@redhat.com>
Cc: d.hatayama@fujitsu.com
Cc: dhowells@redhat.com
Cc: ebiederm@xmission.com
Cc: horms@verge.net.au
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jürgen Gross <jgross@suse.com>
Cc: kexec@lists.infradead.org
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: vgoyal@redhat.com
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20191108090027.11082-3-lijiang@redhat.com
Add a jump target so that a call of the function “clk_put”
can be better reused at the end of this function.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The unit descriptor validation may lead to a probe error when the
device provides a buggy descriptor or the validator detected
incorrectly. For identifying such an error and band-aiding, give a
new module option, skip_validation. With this option, the driver
ignores the validation errors with the hexdump of the unit
descriptor, so we can check it in a bit more details.
Link: https://lore.kernel.org/r/20191114165613.7422-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Introduce a new flag in hdmi_spec to indicate the Intel platform-
specific fixups so that we can get rid of the lengthy codec ID
checks. The flag is set in intel_hsw_common_init() commonly.
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20191111190937.19186-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recently introduced unit descriptor validation had some bug for
processing and extension units, it counts a bControlSize byte twice so
it expected a bigger size than it should have been. This seems
resulting in a probe error on a few devices.
Fix the calculation for proper checks of PU and EU.
Fixes: 57f8770620 ("ALSA: usb-audio: More validations of descriptor units")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191114165613.7422-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There used to be a bug in the video driver that caused the timings
for the LCD to calculate in a way on the DM3730 which made it hang.
The work around for this bug was to set
CONFIG_OMAP2_DSS_MIN_FCK_PER_PCK=4 in the kernel. This work around
is no longer needed as the video drivers have been corrected.
This patch removes the legacy note.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The baseboard of the Logic PD Torpedo development kit has a socket
for a rechargable battery. The battery is monitored by a charger
which can communicate of the the 1-wire HDQ pin.
This patch enables the pinmux for the HDQ pin.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Schema errors can cause make to exit before useful information is
printed. This leaves developers wondering what's wrong. It can be
overcome passing '-k' to make, but that's not an obvious solution.
There's 2 scenarios where this happens.
When using DT_SCHEMA_FILES to validate with a single schema, any error
in the schema results in processed-schema.yaml being empty causing a
make error. The result is the specific errors in the schema are never
shown because processed-schema.yaml is the first target built. Simply
making processed-schema.yaml last in extra-y ensures the full schema
validation with detailed error messages happen first.
The 2nd problem is while schema errors are ignored for
processed-schema.yaml, full validation of the schema still runs in
parallel and any schema validation errors will still stop the build when
running validation of dts files. The fix is to not add the schema
examples to extra-y in this case. This means 'dtbs_check' is no longer a
superset of 'dt_binding_check'. Update the documentation to make this
clear.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Convert Samsung Exynos Soc Power Domain bindings to DT schema format using
json-schema.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Convert Generic Power Domain bindings to DT schema format using
json-schema.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
We have local timers on Cortex-A9, so using the gptimer option makes no
sense. Let's just drop it for omap4 to simplify the timer options a bit.
If this is really needed, it can be still done by specifying dts properties
in the board specific file for assigned-clocks and assigned-clock-parents.
This gets us a bit closer to start dropping legacy platform data for
gptimers except for timer1 that is used for system clockevent.
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
