The existing width field used to check divider validity does not provide
enough protection against bad values. For example, if max divider value
is 4, the smallest all-1 bitmask that can hold this value is 7, which
allows values higher than 4 to be used. This typically causes
unpredictable results with hardware. So far this issue hasn't been
noticed as most of the dividers actually have maximum values which fit
the whole bitfield, but there are certain clocks for which this is a
problem, like dpll4_m4 divider on omap3 devices.
Thus, convert the whole validity logic to use min,max and mask values
for determining if a specific divider is valid or not. This prevents
the odd cases where bad value would otherwise be written to a divider
config register.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Cleanup the ti_clk_parse_divider_data to pass the divider data struct
directly instead of individual values of it. This makes it easier
to modify the implementation later on.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Cleanup couple of TI divider clock internal APIs. These currently pass
huge amount of parameters, which makes it difficult to track what is
going on. Abstract most of these under struct clk_omap_div which gets
passed over the APIs.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
The Kryo cores share errata 1009 with Falkor, so add their model
definitions and enable it for them as well.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[will: Update entry in silicon-errata.rst]
Signed-off-by: Will Deacon <will@kernel.org>
There is no other code use the RT1011_INIT_REG_LEN definition,
except rt1011_reg_init().
Hence, we remove it and fix the typo.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20191031115446.21108-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The !component->card->instantiated statement should remove in kcontrol.
It is no need to check the card->instantiated in kcontrol.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20191031115401.20898-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Due to the way ti sysc and hardreset line control is now implemented,
it is not possible to poll the clock status for gfx clock independent
of hardreset line control. Thus, add a flag to prevent handling this
status bit from clock driver. Correct sequencing of events is guaranteed
by ti-sysc bus driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Due to the way ti sysc and hardreset line control is now implemented,
it is not possible to poll the clock status for gfx clock independent
of hardreset line control. Thus, add a flag to prevent handling this
status bit from clock driver. Correct sequencing of events is guaranteed
by ti-sysc bus driver.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The PRUSS module on AM33xx SoCs has a hardreset line and is controlled
by a PRCM reset line. Any clkctrl enable/disable operations cannot be
checked for module enabled/disabled status independent of the reset
operation, and this causes some unwanted timeouts in the kernel and
unbalanced states for the PRUSS clocks. These details should be handled
by the driver integration code itself.
Add the CLKF_NO_IDLEST flag to the PRUSS clkctrl clock so that these
module status checks are skipped.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The PRUSS modules on AM43xx SoCs have a hardreset line and are controlled
by a PRCM reset line. Any clkctrl enable/disable operations cannot be
checked for module enabled/disabled status independent of the reset
operation, and this causes some unwanted timeouts in the kernel and
unbalanced states for the PRUSS clocks. These details should be handled
by the driver integration code itself.
Add the CLKF_NO_IDLEST flag to the PRUSS clkctrl clock so that these
module status checks are skipped.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The IPU and DSP remote processor cores and their corresponding MMUs on
OMAP5 SoCs have hardreset lines associated with them and are controlled
by a PRCM reset line each. Any clkctrl enable/disable operations cannot
be checked for module enabled/disabled status independent of the reset
operation, and this causes some unwanted timeouts in the kernel and
unbalanced states for these clocks. These details should be handled by
the driver integration code itself.
Add the CLKF_NO_IDLEST flag to both the IPU and DSP clkctrl clocks so
that these module status checks are skipped.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The IPU and DSP remote processor cores and their corresponding MMUs on
OMAP4 SoCs have hardreset lines associated with them and are controlled
by a PRCM reset line each. Any clkctrl enable/disable operations cannot
be checked for module enabled/disabled status independent of the reset
operation, and this causes some unwanted timeouts in the kernel and
unbalanced states for these clocks. These details should be handled by
the driver integration code itself.
Add the CLKF_NO_IDLEST flag to both the IPU and DSP clkctrl clocks so
that these module status checks are skipped.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The IPU and DSP remote processor cores and their corresponding MMUs on
DRA7 SoCs have hardreset lines associated with them and are controlled
by a PRCM reset line each. Any clkctrl enable/disable operations cannot
be checked for module enabled/disabled status independent of the reset
operation, and this causes some unwanted timeouts in the kernel and
unbalanced states for these clocks. These details should be handled by
the driver integration code itself.
Add the CLKF_NO_IDLEST flag to both the IPU and DSP clkctrl clocks so
that these module status checks are skipped.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
OMAP5 device contains an IVA subsystem (Image and Video Accelerator.)
IVA subsystem clkctrl definitions are currently missing, so add them.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Standby status is provided for certain clkctrl clocks to see if the
given module has entered standby or not. This is mostly needed by
remoteproc code to see if the remoteproc has entered standby and the clock
can be turned off safely.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Apply the proper register function for clkctrl clocks, so they get
registered under the clk_hw_omap list also. This allows checking their
type runtime.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The px30 soc from Rockchip shares the same register description as
the rk3328, so can re-use its definitions.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Enable and add supply to the Mali GPU node on all the
H6 boards.
Regarding the datasheet the maximum time for supply to reach
its voltage is 32ms.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Commit f0b5c2c963 ("phy: qcom-usb-hs: Replace the extcon API")
switched from extcon_register_notifier() to the resource-managed
API, i.e. devm_extcon_register_notifier().
This is problematic in this case, because the extcon notifier
is dynamically registered/unregistered whenever the PHY is powered
on/off. The resource-managed API does not unregister the notifier
until the driver is removed, so as soon as the PHY is power cycled,
attempting to register the notifier again results in:
double register detected
WARNING: CPU: 1 PID: 182 at kernel/notifier.c:26 notifier_chain_register+0x74/0xa0
Call trace:
...
extcon_register_notifier+0x74/0xb8
devm_extcon_register_notifier+0x54/0xb8
qcom_usb_hs_phy_power_on+0x1fc/0x208
...
... and USB stops working after plugging the cable out and in
another time.
The easiest way to fix this is to make a partial revert of
commit f0b5c2c963 ("phy: qcom-usb-hs: Replace the extcon API")
and avoid using the resource-managed API in this case.
Fixes: f0b5c2c963 ("phy: qcom-usb-hs: Replace the extcon API")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Fix the below smatch warning by adding variable check rather than the
hardcoded value.
warn: array off by one? 'data->select_value[channel_num]'
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: e52a632195 ("phy: lantiq: vrx200-pcie: add a driver for the Lantiq VRX200 PCIe PHY")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This adds a yaml binding for the external dsi phy found on Rockchip
socs of the px30, rk3128 and rk3368 variants.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The Innosilicon Video Combo PHY not only supports MIPI DSI,
but also LVDS and TTL functions with small die size and low
pin count. Customers can choose according to their own applications.
Signed-off-by: Wyon Bi <bivvy.bi@rock-chips.com>
[removed TTL mode for now, as it required a hook back into the dsi host]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
There are combo phys out there that can be switched between doing
dsi and lvds. So add a mode definition for it.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Allwinner H6 SoC contains a USB3 PHY (with USB2 DP/DM lines also
controlled).
Add a driver for it.
The register operations in this driver is mainly extracted from the BSP
USB3 driver.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The new Allwinner H6 SoC contains a USB3 PHY that is wired to the
external USB3 pins of the SoC.
Add a device tree binding for the PHY.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
VMX already does so if the host has SMEP, in order to support the combination of
CR0.WP=1 and CR4.SMEP=1. However, it is perfectly safe to always do so, and in
fact VMX already ends up running with EFER.NXE=1 on old processors that lack the
"load EFER" controls, because it may help avoiding a slow MSR write. Removing
all the conditionals simplifies the code.
SVM does not have similar code, but it should since recent AMD processors do
support SMEP. So this patch also makes the code for the two vendors more similar
while fixing NPT=0, CR0.WP=1 and CR4.SMEP=1 on AMD processors.
Cc: stable@vger.kernel.org
Cc: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In kvm_create_vm(), if we've successfully called kvm_arch_init_vm(), but
then fail later in the function, we need to call kvm_arch_destroy_vm()
so that it can do any necessary cleanup (like freeing memory).
Fixes: 44a95dae1d ("KVM: x86: Detect and Initialize AVIC support")
Signed-off-by: John Sperbeck <jsperbeck@google.com>
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Junaid Shahid <junaids@google.com>
[Remove dependency on "kvm: Don't clear reference count on
kvm_create_vm() error path" which was not committed. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The clk_half_divider_ops is not used outside or declared
outside of drivers/clk/rockchip/clk-half-divider.c so make
it static to avoid the following warning:
drivers/clk/rockchip/clk-half-divider.c:142:22: warning: symbol 'clk_half_divider_ops' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20191017105348.8061-1-ben.dooks@codethink.co.uk
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
All boards using rk3288-veyron-analog-audio.dtsi have HDMI audio.
Specify the support of HDMI audio on machine driver using
rockchip,hdmi-codec property so machine driver creates HDMI audio device.
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Link: https://lore.kernel.org/r/20191028071930.145899-6-cychiang@chromium.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The linux-i3c mailing list is moderated for non-subscribers.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
The driver exposes EFI runtime services to user-space through an IOCTL
interface, calling the EFI services function pointers directly without
using the efivar API.
Disallow access to the /dev/efi_test character device when the kernel is
locked down to prevent arbitrary user-space to call EFI runtime services.
Also require CAP_SYS_ADMIN to open the chardev to prevent unprivileged
users to call the EFI runtime services, instead of just relying on the
chardev file mode bits for this.
The main user of this driver is the fwts [0] tool that already checks if
the effective user ID is 0 and fails otherwise. So this change shouldn't
cause any regression to this tool.
[0]: https://wiki.ubuntu.com/FirmwareTestSuite/Reference/uefivarinfo
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Acked-by: Matthew Garrett <mjg59@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: https://lkml.kernel.org/r/20191029173755.27149-7-ardb@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently, kernel fails to boot on some HyperV VMs when using EFI.
And it's a potential issue on all x86 platforms.
It's caused by broken kernel relocation on EFI systems, when below three
conditions are met:
1. Kernel image is not loaded to the default address (LOAD_PHYSICAL_ADDR)
by the loader.
2. There isn't enough room to contain the kernel, starting from the
default load address (eg. something else occupied part the region).
3. In the memmap provided by EFI firmware, there is a memory region
starts below LOAD_PHYSICAL_ADDR, and suitable for containing the
kernel.
EFI stub will perform a kernel relocation when condition 1 is met. But
due to condition 2, EFI stub can't relocate kernel to the preferred
address, so it fallback to ask EFI firmware to alloc lowest usable memory
region, got the low region mentioned in condition 3, and relocated
kernel there.
It's incorrect to relocate the kernel below LOAD_PHYSICAL_ADDR. This
is the lowest acceptable kernel relocation address.
The first thing goes wrong is in arch/x86/boot/compressed/head_64.S.
Kernel decompression will force use LOAD_PHYSICAL_ADDR as the output
address if kernel is located below it. Then the relocation before
decompression, which move kernel to the end of the decompression buffer,
will overwrite other memory region, as there is no enough memory there.
To fix it, just don't let EFI stub relocate the kernel to any address
lower than lowest acceptable address.
[ ardb: introduce efi_low_alloc_above() to reduce the scope of the change ]
Signed-off-by: Kairui Song <kasong@redhat.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: https://lkml.kernel.org/r/20191029173755.27149-6-ardb@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The EFI stubloader for ARM starts out by allocating a 32 MB window
at the base of RAM, in order to ensure that the decompressor (which
blindly copies the uncompressed kernel into that window) does not
overwrite other allocations that are made while running in the context
of the EFI firmware.
In some cases, (e.g., U-Boot running on the Raspberry Pi 2), this is
causing boot failures because this initial allocation conflicts with
a page of reserved memory at the base of RAM that contains the SMP spin
tables and other pieces of firmware data and which was put there by
the bootloader under the assumption that the TEXT_OFFSET window right
below the kernel is only used partially during early boot, and will be
left alone once the memory reservations are processed and taken into
account.
So let's permit reserved memory regions to exist in the region starting
at the base of RAM, and ending at TEXT_OFFSET - 5 * PAGE_SIZE, which is
the window below the kernel that is not touched by the early boot code.
Tested-by: Guillaume Gardet <Guillaume.Gardet@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Chester Lin <clin@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: https://lkml.kernel.org/r/20191029173755.27149-5-ardb@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit 428826f535 ("fdt: add support for rng-seed") introduced
add_bootloader_randomness(), permitting randomness provided by the
bootloader or firmware to be credited as entropy. However, the fact
that the UEFI support code was already wired into the RNG subsystem
via a call to add_device_randomness() was overlooked, and so it was
not converted at the same time.
Note that this UEFI (v2.4 or newer) feature is currently only
implemented for EFI stub booting on ARM, and further note that
CONFIG_RANDOM_TRUST_BOOTLOADER must be enabled, and this should be
done only if there indeed is sufficient trust in the bootloader
_and_ its source of randomness.
[ ardb: update commit log ]
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: https://lkml.kernel.org/r/20191029173755.27149-4-ardb@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently nothing checks the return value of efi_tpm_eventlog_init(),
but in case that changes in the future make sure an error is
returned when it fails to determine the tpm final events log
size.
Suggested-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Fixes: e658c82be5 ("efi/tpm: Only set 'efi_tpm_final_log_size' after ...")
Link: https://lkml.kernel.org/r/20191029173755.27149-3-ardb@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
For the EFI_RCI2_TABLE Kconfig option, 'make oldconfig' asks the user
for input on platforms where the option may not be applicable. This patch
modifies the Kconfig option to ask the user for input only when CONFIG_X86
or CONFIG_COMPILE_TEST is set to y.
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Narendra K <Narendra.K@dell.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: https://lkml.kernel.org/r/20191029173755.27149-2-ardb@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull RCU and LKMM changes from Paul E. McKenney:
- Documentation updates.
- Miscellaneous fixes.
- Dynamic tick (nohz) updates, perhaps most notably changes to
force the tick on when needed due to lengthy in-kernel execution
on CPUs on which RCU is waiting.
- Replace rcu_swap_protected() with rcu_prepace_pointer().
- Torture-test updates.
- Linux-kernel memory consistency model updates.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Remove unneeded ret variable from ath5k_eeprom_read_spur_chans()
Signed-off-by: Saurav Girepunje <saurav.girepunje@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
