Escalation interrupts are interrupts sent to the host by the XIVE
hardware when it has an interrupt to deliver to a guest VCPU but that
VCPU is not running anywhere in the system. Hence we disable the
escalation interrupt for the VCPU being run when we enter the guest
and re-enable it when the guest does an H_CEDE hypercall indicating
it is idle.
It is possible that an escalation interrupt gets generated just as we
are entering the guest. In that case the escalation interrupt may be
using a queue entry in one of the interrupt queues, and that queue
entry may not have been processed when the guest exits with an H_CEDE.
The existing entry code detects this situation and does not clear the
vcpu->arch.xive_esc_on flag as an indication that there is a pending
queue entry (if the queue entry gets processed, xive_esc_irq() will
clear the flag). There is a comment in the code saying that if the
flag is still set on H_CEDE, we have to abort the cede rather than
re-enabling the escalation interrupt, lest we end up with two
occurrences of the escalation interrupt in the interrupt queue.
However, the exit code doesn't do that; it aborts the cede in the sense
that vcpu->arch.ceded gets cleared, but it still enables the escalation
interrupt by setting the source's PQ bits to 00. Instead we need to
set the PQ bits to 10, indicating that an interrupt has been triggered.
We also need to avoid setting vcpu->arch.xive_esc_on in this case
(i.e. vcpu->arch.xive_esc_on seen to be set on H_CEDE) because
xive_esc_irq() will run at some point and clear it, and if we race with
that we may end up with an incorrect result (i.e. xive_esc_on set when
the escalation interrupt has just been handled).
It is extremely unlikely that having two queue entries would cause
observable problems; theoretically it could cause queue overflow, but
the CPU would have to have thousands of interrupts targetted to it for
that to be possible. However, this fix will also make it possible to
determine accurately whether there is an unhandled escalation
interrupt in the queue, which will be needed by the following patch.
Fixes: 9b9b13a6d1 ("KVM: PPC: Book3S HV: Keep XIVE escalation interrupt masked unless ceded")
Cc: stable@vger.kernel.org # v4.16+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190813100349.GD9567@blackberry
When a vCPU is brought done, the XIVE VP (Virtual Processor) is first
disabled and then the event notification queues are freed. When freeing
the queues, we check for possible escalation interrupts and free them
also.
But when a XIVE VP is disabled, the underlying XIVE ENDs also are
disabled in OPAL. When an END (Event Notification Descriptor) is
disabled, its ESB pages (ESn and ESe) are disabled and loads return all
1s. Which means that any access on the ESB page of the escalation
interrupt will return invalid values.
When an interrupt is freed, the shutdown handler computes a 'saved_p'
field from the value returned by a load in xive_do_source_set_mask().
This value is incorrect for escalation interrupts for the reason
described above.
This has no impact on Linux/KVM today because we don't make use of it
but we will introduce in future changes a xive_get_irqchip_state()
handler. This handler will use the 'saved_p' field to return the state
of an interrupt and 'saved_p' being incorrect, softlockup will occur.
Fix the vCPU cleanup sequence by first freeing the escalation interrupts
if any, then disable the XIVE VP and last free the queues.
Fixes: 90c73795af ("KVM: PPC: Book3S HV: Add a new KVM device for the XIVE native exploitation mode")
Fixes: 5af5099385 ("KVM: PPC: Book3S HV: Native usage of the XIVE interrupt controller")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190806172538.5087-1-clg@kaod.org
A couple of independent patches extracted from the 5.3 pull request, fixed for
merge conflicts and a single unused variable warning.
And the drmP.h removal from Sam.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Enable the ACPI_APEI_PCIEAER configuration to support PCIe AER error report
for the Hisilicon D06 board and the dependencies PCIEAER and ACPI_APEI have
been enabled in the default config.
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Currently libbpf version is specified in 2 places: libbpf.map and
Makefile. They easily get out of sync and it's very easy to update one,
but forget to update another one. In addition, Github projection of
libbpf has to maintain its own version which has to be remembered to be
kept in sync manually, which is very error-prone approach.
This patch makes libbpf.map a source of truth for libbpf version and
uses shell invocation to parse out correct full and major libbpf version
to use during build. Now we need to make sure that once new release
cycle starts, we need to add (initially) empty section to libbpf.map
with correct latest version.
This also will make it possible to keep Github projection consistent
with kernel sources version of libbpf by adopting similar parsing of
version from libbpf.map.
v2->v3:
- grep -o + sort -rV (Andrey);
v1->v2:
- eager version vars evaluation (Jakub);
- simplified version regex (Andrey);
Cc: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Daniel T. Lee says:
====================
Currently, bpftool net only supports dumping progs attached on the
interface. To attach XDP prog on interface, user must use other tool
(eg. iproute2). By this patch, with `bpftool net attach/detach`, user
can attach/detach XDP prog on interface.
# bpftool prog
16: xdp name xdp_prog1 tag 539ec6ce11b52f98 gpl
loaded_at 2019-08-07T08:30:17+0900 uid 0
...
20: xdp name xdp_fwd_prog tag b9cb69f121e4a274 gpl
loaded_at 2019-08-07T08:30:17+0900 uid 0
# bpftool net attach xdpdrv id 16 dev enp6s0np0
# bpftool net
xdp:
enp6s0np0(4) driver id 16
# bpftool net attach xdpdrv id 20 dev enp6s0np0 overwrite
# bpftool net
xdp:
enp6s0np0(4) driver id 20
# bpftool net detach xdpdrv dev enp6s0np0
# bpftool net
xdp:
While this patch only contains support for XDP, through `net
attach/detach`, bpftool can further support other prog attach types.
XDP attach/detach tested on Mellanox ConnectX-4 and Netronome Agilio.
---
Changes in v5:
- fix wrong error message, from errno to err with do_attach/detach
Changes in v4:
- rename variable, attach/detach error message enhancement
- bash-completion cleanup, doc update with brief description (attach
types)
Changes in v3:
- added 'overwrite' option for replacing previously attached XDP prog
- command argument order has been changed ('ATTACH_TYPE' comes first)
- add 'dev' keyword in front of <devname>
- added bash-completion and documentation
Changes in v2:
- command 'load/unload' changed to 'attach/detach' for the consistency
====================
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Since, new sub-command 'net attach/detach' has been added for
attaching XDP program on interface,
this commit documents usage and sample output of `net attach/detach`.
Signed-off-by: Daniel T. Lee <danieltimlee@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This commit adds bash-completion for new "net attach/detach"
subcommand for attaching XDP program on interface.
Signed-off-by: Daniel T. Lee <danieltimlee@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
By this commit, using `bpftool net detach`, the attached XDP prog can
be detached. Detaching the BPF prog will be done through libbpf
'bpf_set_link_xdp_fd' with the progfd set to -1.
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel T. Lee <danieltimlee@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
By this commit, using `bpftool net attach`, user can attach XDP prog on
interface. New type of enum 'net_attach_type' has been made, as stat ted at
cover-letter, the meaning of 'attach' is, prog will be attached on interface.
With 'overwrite' option at argument, attached XDP program could be replaced.
Added new helper 'net_parse_dev' to parse the network device at argument.
BPF prog will be attached through libbpf 'bpf_set_link_xdp_fd'.
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel T. Lee <danieltimlee@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
-----BEGIN PGP SIGNATURE-----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=zu2P
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-fixes-20190814' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Fix local endpoint handling
Here's a pair of patches that fix two issues in the handling of local
endpoints (rxrpc_local structs):
(1) Use list_replace_init() rather than list_replace() if we're going to
unconditionally delete the replaced item later, lest the list get
corrupted.
(2) Don't access the rxrpc_local object after passing our ref to the
workqueue, not even to illuminate tracepoints, as the work function
may cause the object to be freed. We have to cache the information
beforehand.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart says:
====================
net: mscc: PTP Hardware Clock (PHC) support
This series introduces the PTP Hardware Clock (PHC) support to the Mscc
Ocelot switch driver. In order to make use of this, a new register bank
is added and described in the device tree, as well as a new interrupt.
The use this bank and interrupt was made optional in the driver for dt
compatibility reasons.
Thanks!
Antoine
Since v5:
- Made sure both the PTP interrupt and register bank were available to
enable supporting h/w timestamping.
- Added a check after a kzalloc.
- Add Reviewed-by tags from Andrew.
Since v4:
- Added SKBTX_IN_PROGRESS.
- Fixed two xmas trees.
- Rework the loop condition in ocelot_ptp_rdy_irq_handler.
Since v3:
- Fixed a spin_unlock_irqrestore issue.
Since v2:
- Prevented from a possible infinite loop when reading the h/w
timestamps.
- s/GFP_KERNEL/GFP_ATOMIC/ in the Tx path.
- Set rx_filter to HWTSTAMP_FILTER_PTP_V2_EVENT at probe.
- Fixed s/w timestamping dependencies.
- Added Paul Burton's Acked-by on patches 2 and 4.
Since v1:
- Used list_for_each_safe() in ocelot_deinit().
- Fixed a memory leak in ocelot_deinit() by calling
dev_kfree_skb_any().
- Fixed a locking issue in get_hwtimestamp().
- Handled the NULL case of ptp_clock_register().
- Added comments on optional dt properties.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for PTP Hardware Clock (PHC) to the Ocelot
switch for both PTP 1-step and 2-step modes.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In struct frame_info, the cpuq member is never used. This cosmetic patch
removes it from the structure, and from the parsing of the frame header
as it's only set but never used.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This cosmetic patch improves the frame header parsing readability by
introducing a new macro to access and mask its fields.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for using the PTP register range, and adds a
description of its registers. This bank is used when configuring PTP.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
One additional interrupt needs to be described within the Ocelot device
tree node: the PTP ready one. This patch documents the binding needed to
do so.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
One additional register range needs to be described within the Ocelot
device tree node: the PTP. This patch documents the binding needed to do
so.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with commit 72175d4ea4 ("driver core: Make driver core
own stateful device links") stateful device links are owned by the
driver core and should not be explicitly removed on device unbind.
Delete all device_link_remove appearances from the dpio driver.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Forgo the struct_mutex requirement for request retirement as we have
been transitioning over to only using the timeline->mutex for
controlling the lifetime of a request on that timeline.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190815205709.24285-4-chris@chris-wilson.co.uk
In preparation for removing struct_mutex from around context retirement,
we need to make timeline pinning and unpinning safe. Since multiple
engines/contexts can share a single timeline, we cannot rely on
borrowing the context mutex (otherwise we could state that the timeline
is only pinned/unpinned inside the context pin/unpin and so guarded by
it). However, we only perform a sequence of atomic operations inside the
timeline pin/unpin and the sequence of those operations is safe for a
concurrent unpin / pin, so we can relax the struct_mutex requirement.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190815205709.24285-3-chris@chris-wilson.co.uk
Adding compatible string "ls1028a-dcfg" to initialize guts driver
for ls1028 and SoC die attribute definition for LS1028A
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
When using the reserved memory node in the device tree there are
two options - dynamic or static. If a dynamic allocation was
selected (where the kernel selects the address for the allocation)
convert it to a static allocation by inserting the reg property.
This will ensure the same memory is reused after a kexec()
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
When shutting down a FQ on a dedicated channel only the
SW portal associated with that channel can dequeue from it.
Make sure the correct portal is use.
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
The drain_mr_fqni() function may be called fron uninterruptable
context so convert the msleep() to an mdelay(). Also ensure that
the valid bit is updated while polling.
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
If the QMan device was previously initialized make sure all the
frame queues are out of service once all the portals are probed.
This handles the case where the kernel is restarted without the
SoC being reset (kexec for example)
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Clean the BMan buffer pools if the device had been initialized
previously. This will ensure a consistent state if the kernel
was soft restarted (kexec for example)
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Rework QBMan private memory setup so that the areas are not
zeroed if the device was previously initialized
If the QMan private memory was already initialized skip the PFDR
initialization.
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Thierry Reding <treding@nvidia.com>
Cc: Li Yang <leoyang.li@nxp.com>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
This patchset contains Netfilter fixes for net:
1) Extend selftest to cover flowtable with ipsec, from Florian Westphal.
2) Fix interaction of ipsec with flowtable, also from Florian.
3) User-after-free with bound set to rule that fails to load.
4) Adjust state and timeout for flows that expire.
5) Timeout update race with flows in teardown state.
6) Ensure conntrack id hash calculation use invariants as input,
from Dirk Morris.
7) Do not push flows into flowtable for TCP fin/rst packets.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A process could race in an open and attempt to read one of these files
before i_private is initialized, and get a spurious error.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Fix a crash that was introduced by the commit 724376a04d. The crash is
reported here: https://gitlab.com/cryptsetup/cryptsetup/issues/468
When reading from the integrity device, the function
dm_integrity_map_continue calls find_journal_node to find out if the
location to read is present in the journal. Then, it calculates how many
sectors are consecutively stored in the journal. Then, it locks the range
with add_new_range and wait_and_add_new_range.
The problem is that during wait_and_add_new_range, we hold no locks (we
don't hold ic->endio_wait.lock and we don't hold a range lock), so the
journal may change arbitrarily while wait_and_add_new_range sleeps.
The code then goes to __journal_read_write and hits
BUG_ON(journal_entry_get_sector(je) != logical_sector); because the
journal has changed.
In order to fix this bug, we need to re-check the journal location after
wait_and_add_new_range. We restrict the length to one block in order to
not complicate the code too much.
Fixes: 724376a04d ("dm integrity: implement fair range locks")
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
dm-zoned is observed to lock up or livelock in case of hardware
failure or some misconfiguration of the backing zoned device.
This patch adds a new dm-zoned target function that checks the status of
the backing device. If the request queue of the backing device is found
to be in dying state or the SCSI backing device enters offline state,
the health check code sets a dm-zoned target flag prompting all further
incoming I/O to be rejected. In order to detect backing device failures
timely, this new function is called in the request mapping path, at the
beginning of every reclaim run and before performing any metadata I/O.
The proper way out of this situation is to do
dmsetup remove <dm-zoned target>
and recreate the target when the problem with the backing device
is resolved.
Fixes: 3b1a94c88b ("dm zoned: drive-managed zoned block device target")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Some errors are ignored in the I/O path during queueing chunks
for processing by chunk works. Since at least these errors are
transient in nature, it should be possible to retry the failed
incoming commands.
The fix -
Errors that can happen while queueing chunks are carried upwards
to the main mapping function and it now returns DM_MAPIO_REQUEUE
for any incoming requests that can not be properly queued.
Error logging/debug messages are added where needed.
Fixes: 3b1a94c88b ("dm zoned: drive-managed zoned block device target")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
There are several places in reclaim code where errors are not
propagated to the main function, dmz_reclaim(). This function
is responsible for unlocking zones that might be still locked
at the end of any failed reclaim iterations. As the result,
some device zones may be left permanently locked for reclaim,
degrading target's capability to reclaim zones.
This patch fixes these issues as follows -
Make sure that dmz_reclaim_buf(), dmz_reclaim_seq_data() and
dmz_reclaim_rnd_data() return error codes to the caller.
dmz_reclaim() function is renamed to dmz_do_reclaim() to avoid
clashing with "struct dmz_reclaim" and is modified to return the
error to the caller.
dmz_get_zone_for_reclaim() now returns an error instead of NULL
pointer and reclaim code checks for that error.
Error logging/debug messages are added where necessary.
Fixes: 3b1a94c88b ("dm zoned: drive-managed zoned block device target")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This patch fixes a problem in dm-kcopyd that may leave jobs in
complete queue indefinitely in the event of backing storage failure.
This behavior has been observed while running 100% write file fio
workload against an XFS volume created on top of a dm-zoned target
device. If the underlying storage of dm-zoned goes to offline state
under I/O, kcopyd sometimes never issues the end copy callback and
dm-zoned reclaim work hangs indefinitely waiting for that completion.
This behavior was traced down to the error handling code in
process_jobs() function that places the failed job to complete_jobs
queue, but doesn't wake up the job handler. In case of backing device
failure, all outstanding jobs may end up going to complete_jobs queue
via this code path and then stay there forever because there are no
more successful I/O jobs to wake up the job handler.
This patch adds a wake() call to always wake up kcopyd job wait queue
for all I/O jobs that fail before dm_io() gets called for that job.
The patch also sets the write error status in all sub jobs that are
failed because their master job has failed.
Fixes: b73c67c2cb ("dm kcopyd: add sequential write feature")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Revert the commit bd293d071f. The proper
fix has been made available with commit d0a255e795 ("loop: set
PF_MEMALLOC_NOIO for the worker thread").
Note that the fix offered by commit bd293d071f doesn't really prevent
the deadlock from occuring - if we look at the stacktrace reported by
Junxiao Bi, we see that it hangs in bit_wait_io and not on the mutex -
i.e. it has already successfully taken the mutex. Changing the mutex
from mutex_lock to mutex_trylock won't help with deadlocks that happen
afterwards.
PID: 474 TASK: ffff8813e11f4600 CPU: 10 COMMAND: "kswapd0"
#0 [ffff8813dedfb938] __schedule at ffffffff8173f405
#1 [ffff8813dedfb990] schedule at ffffffff8173fa27
#2 [ffff8813dedfb9b0] schedule_timeout at ffffffff81742fec
#3 [ffff8813dedfba60] io_schedule_timeout at ffffffff8173f186
#4 [ffff8813dedfbaa0] bit_wait_io at ffffffff8174034f
#5 [ffff8813dedfbac0] __wait_on_bit at ffffffff8173fec8
#6 [ffff8813dedfbb10] out_of_line_wait_on_bit at ffffffff8173ff81
#7 [ffff8813dedfbb90] __make_buffer_clean at ffffffffa038736f [dm_bufio]
#8 [ffff8813dedfbbb0] __try_evict_buffer at ffffffffa0387bb8 [dm_bufio]
#9 [ffff8813dedfbbd0] dm_bufio_shrink_scan at ffffffffa0387cc3 [dm_bufio]
#10 [ffff8813dedfbc40] shrink_slab at ffffffff811a87ce
#11 [ffff8813dedfbd30] shrink_zone at ffffffff811ad778
#12 [ffff8813dedfbdc0] kswapd at ffffffff811ae92f
#13 [ffff8813dedfbec0] kthread at ffffffff810a8428
#14 [ffff8813dedfbf50] ret_from_fork at ffffffff81745242
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Fixes: bd293d071f ("dm bufio: fix deadlock with loop device")
Depends-on: d0a255e795 ("loop: set PF_MEMALLOC_NOIO for the worker thread")
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The BSpec has added three new IDS for CML.
Update the IDs in accordance to the Spec.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190812222737.29356-1-anusha.srivatsa@intel.com
Sudarsana Reddy Kalluru says:
====================
qed*: Support for NVM config attributes.
The patch series adds support for managing the NVM config attributes.
Patch (1) adds functionality to update config attributes via MFW.
Patch (2) adds driver interface for updating the config attributes.
Changes from previous versions:
-------------------------------
v4: Added more details on the functionality and its usage.
v3: Removed unused variable.
v2: Removed unused API.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds driver interface for reading the config attributes from user
provided buffer, and updates these values on nvm config flash partition.
This is basically an expansion of our existing ethtool -f implementation.
The management FW has exposed an additional method of configuring some of
the nvram options, and this makes use of that. This implementation will
come into use when newer FW files which contain configuration directives
employing this API will be provided to ethtool -f.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds API for configuring the NVM config attributes using
Management FW (MFW) interfaces.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
`check_input_term` recursively calls itself with input from
device side (e.g., uac_input_terminal_descriptor.bCSourceID)
as argument (id). In `check_input_term`, if `check_input_term`
is called with the same `id` argument as the caller, it triggers
endless recursive call, resulting kernel space stack overflow.
This patch fixes the bug by adding a bitmap to `struct mixer_build`
to keep track of the checked ids and stop the execution if some id
has been checked (similar to how parse_audio_unit handles unitid
argument).
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: Hui Peng <benquike@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
