In tc_bridge_mode_set callback, we store the pointer to the given
drm_display_mode, and use the mode later. Storing a pointer in such a
way looks very suspicious to me, and I have observed odd issues where
the timings were apparently (at least mostly) zero.
Do a copy of the drm_display_mode instead to ensure we don't refer to
freed/modified data.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-21-tomi.valkeinen@ti.com
drm_connector_helper_funcs.best_encoder is only needed when the
connector can have more than one encoder, and that is never the case
here.
So remove tc_connector_best_encoder.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-20-tomi.valkeinen@ti.com
We have tc_connector_mode_valid() to filter out videomdoes that the
tc358767 cannot support. As it is a bridge limitation, change the code
to use drm_bridge_funcs's mode_valid instead.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-19-tomi.valkeinen@ti.com
tc_main_link_enable() checks if videomode has been set, and fails if
there's no videomode. As tc_main_link_enable() no longer depends on the
videomode, we can drop the check.
Also, while tc_stream_enable() does depend on the videomode, we can
expect that a mode has been set before drm_bridge_funcs.enable is
called, so we don't need the check there either.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-18-tomi.valkeinen@ti.com
The current link training code does unnecessary retry-loops, and does
extra writes to the registers. It is easier to follow the flow and
ensure it's similar to Toshiba's documentation if we deal with LT inside
tc_main_link_enable() function.
This patch adds tc_wait_link_training() which handles waiting for the LT
phase to finish, and does the necessary LT register setups in
tc_main_link_enable, without extra loops.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-17-tomi.valkeinen@ti.com
The driver has a loop after ending link training, where it reads the
DPCD link status and prints an error if that status is not ok.
The loop is unnecessary, as far as I can understand from DP specs, so
let's remove it. We can also print the more specific errors to help
debugging.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-16-tomi.valkeinen@ti.com
At the end of the link training, two steps have to be taken: 1)
tc358767's LT mode is disabled by a write to DP0_SRCCTRL, and 2) Remove
LT flag in DPCD 0x102.
Toshiba's documentation tells to first write the DPCD, then modify
DP0_SRCCTRL. In my testing this often causes issues, and the link
disconnects right after those steps.
If I reverse the steps, it works every time. There's a chance that this
is DP sink specific, though, but as my testing shows this sequence to be
much more reliable, let's change it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-15-tomi.valkeinen@ti.com
For some reason the driver has a msleep(100) after writing to
DP_PHY_CTRL. Toshiba's documentation doesn't suggest any delay is
needed, and I have not seen any issues with the sleep removed.
Drop it, as msleep(100) is a rather big one.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-14-tomi.valkeinen@ti.com
Link training will sometimes fail if the DP link is enabled when
tc_main_link_enable() is called. The driver makes sure the DP link is
disabled when the DP output is disabled, and we never enable the DP
without first disabling it, so this should never happen.
However, as the HW behavior seems to be somewhat random if DP link has
erroneously been left enabled, let's add a WARN_ON() for the case and
set DP0CTL to 0.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-13-tomi.valkeinen@ti.com
Currently the code writes 0 to DP0CTL in tc_stream_disable(), which
disables the whole DP link instead of just the video stream. We always
disable the link and the stream together from tc_bridge_disable(), so
this doesn't cause any issues.
Nevertheless, fix this by only clearing VID_EN in tc_stream_disable to
stop the video stream while keeping the link enabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-12-tomi.valkeinen@ti.com
Currently we have tc_main_link_setup(), which configures and enabled the
link, but we have no counter-part for disabling the link.
Add tc_main_link_disable, and rename tc_main_link_setup to
tc_main_link_enable.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-11-tomi.valkeinen@ti.com
We set up the PXL PLL inside tc_main_link_setup. This is unnecessary,
and makes tc_main_link_setup depend on the video-mode, which should not
be the case. As PXL PLL is used only for the video stream (and only when
using the HW test pattern), let's move the PXL PLL setup into
tc_stream_enable.
Also, currently the PXL PLL is only disabled if the driver if removed.
Let's disable the PXL PLL when the stream is disabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-10-tomi.valkeinen@ti.com
It is nicer to have enable/disable functions instead of set(bool enable)
style function.
Split tc_main_link_stream into tc_stream_enable and tc_stream_disable.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-9-tomi.valkeinen@ti.com
The driver currently sets the video stream registers in
tc_main_link_setup. One should be able to establish the DP link without
any video stream, so a more logical place is to configure the stream in
the tc_main_link_stream. So move them there.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-8-tomi.valkeinen@ti.com
The driver sets up AUX link at probe time, but, for some reason, also
sets the main link's number of lanes using tc->link.base.num_lanes. This
is not needed nor correct, as the number of lanes has not been decided
yet. The number of lanes will be set later during main link setup.
Modify aux_link_setup so that it does not use tc->link, and thus makes
aux setup independent of the link probing.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-7-tomi.valkeinen@ti.com
swing and preemp fields are not used. Remove them.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-6-tomi.valkeinen@ti.com
Minor cleanups:
- Use bool for boolean fields
- Use DP_MAX_DOWNSPREAD_0_5 instead of BIT(0)
- debug print down-spread and scrambler status
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-5-tomi.valkeinen@ti.com
DP always uses ANSI 8B10B encoding. Some monitors (old?) may not have
the ANSI 8B10B bit set in DPCD, even if it should always be set.
The tc358767 driver currently respects that flag, and turns the encoding
off if the monitor does not have the bit set, which then results in the
monitor not working.
This patch makes the driver to always use ANSI 8B10B encoding, and drops
the 'coding8b10b' field which is no longer used.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-4-tomi.valkeinen@ti.com
We need to reset DPCD voltage-swing & pre-emphasis before starting the
link training, as otherwise tc358767 will use the previous values as
minimums.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-3-tomi.valkeinen@ti.com
tc_aux_get_status() does not report AUX_TIMEOUT correctly, as it only
checks the AUX_TIMEOUT if aux is still busy. Fix this by always checking
for AUX_TIMEOUT.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-2-tomi.valkeinen@ti.com
The i915.alpha_support module parameter has caused some confusion along
the way. Add new i915.force_probe parameter to specify PCI IDs of
devices to probe, when the devices are recognized but not automatically
probed by the driver. The name is intended to reflect what the parameter
effectively does, avoiding any overloaded semantics of "alpha" and
"support".
The parameter supports "" to disable, "<pci-id>,[<pci-id>,...]" to
enable force probe for one or more devices, and "*" to enable force
probe for all known devices.
Also add new CONFIG_DRM_I915_FORCE_PROBE config option to replace the
DRM_I915_ALPHA_SUPPORT option. This defaults to "*" if
DRM_I915_ALPHA_SUPPORT=y.
Instead of replacing i915.alpha_support immediately, let the two coexist
for a while, with a deprecation message, for a transition period.
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190506134801.28751-1-jani.nikula@intel.com
The assignment of err is using the incorrect pointer vaddr that has
not been initialized. Fix this by using the correct pointer obj instead.
Addresses-Coverity: ("Uninitialized pointer read")
Fixes: 6501aa4e3a ("drm/i915: add in-kernel blitter client")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190531103201.10124-1-colin.king@canonical.com
The Freescale SPI chipselects are special: while everyone else
is using "cs-gpios" the Freescale platforms just use "gpios".
Fix this by responding with "gpios" when asking for "cs-gpios"
in a freescale device node, so we hide this pecularity from
the SPI core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The normal behaviour is to periodically check for a mmio access error,
and once detected enable mmio access checking. However this is useless
if the error only occurs once during module load, and so we may miss
such errors in CI. To allow ourselves to catch them, allow CI to opt into
always enabling mmio debugging.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190530121311.6794-1-chris@chris-wilson.co.uk
For code simplification and safety, use struct_size() macro for
calculating the hda_conn_list object size with the variable array.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For code simplification and safety, use struct_size() macro for
calculating the snd_kcontrol object size with the variable array.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC255 and ALC256 were some difference for hidden register.
This update was suitable for ALC256.
Fixes: e69e7e03ed ("ALSA: hda/realtek - ALC256 speaker noise issue")
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If PSCI is available then most likely we are running on PSCI-enabled
U-Boot which, we assume, has already taken care of resetting CNTVOFF
and updating counter module before switching to non-secure mode
and we don't need to.
As the psci_smp_available() helper always returns false if CONFIG_SMP
is disabled, it can't be used safely as an indicator of PSCI usage.
For that reason, we check for the mandatory PSCI operation to be
available.
Please note, an extra check to prevent secure_cntvoff_init() from
being called for secondary CPUs in headsmp-apmu.S is not needed,
as SMP code for APMU based system is not executed if PSCI is in use.
Signed-off-by: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Avoid translating "/" and "//" directory entry names to the special
"." and ".." names by instead converting the first character to "^".
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
append_filetype_suffix() is now only used in adfs_object_fixup(), so
move it there.
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
fs/adfs support for truncated filenames is broken, and there is a desire
not to support this into the future. Let's remove the fs/adfs support
for this.
Viro says:
"FWIW, the word from Linus had been basically "kill it off" on
truncation."
That being:
"Make it so. Make the rule be that d_hash() can only change the hash
itself, rather than the subtle special case for len that we had
because of legacy reasons.."
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Move the filename fixup to adfs_object_fixup() so we only have one
implementation of this.
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Factor out the directory object fixups, which parse the filetype and
optionally apply the filetype suffix to the filename.
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Factor out the filename case lowering of directory names when comparing
or hashing filenames.
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
We have essentially the same code in adfs_compare() as adfs_match(), so
arrange to use a common implementation.
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
I tried to find any indication of whether the capi drivers are still in
use, and have not found anything from a long time ago.
With public ISDN networks almost completely shut down over the past 12
months, there is very little you can actually do with this hardware. The
main remaining use case would be to connect ISDN voice phones to an
in-house installation with Asterisk or LCR, but anyone trying this in
turn seems to be using either the mISDN driver stack, or out-of-tree
drivers from the hardware vendors.
I may of course have missed something, so I would suggest moving these
three drivers (avm, hysdn, gigaset) into drivers/staging/ just in case
someone still uses them.
If nobody complains, we can remove them entirely in six months, or
otherwise move the core code and any drivers that are still needed back
into drivers/isdn.
As Paul Bolle notes, he is still testing the gigaset driver as long as
he can, but the Dutch ISDN network will be shut down in September 2019,
which puts an end to that.
Marcel Holtmann still maintains the Bluetooth CMTP profile and wants to
keep that alive, so the actual CAPI subsystem code remains in place for
now, after all other drivers are gone, CMTP and CAPI can be merged into
a single driver directory.
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The last remnant of the isdn4linux interface is now the isdnhdlc
support, used by the netjet driver. Move it next to that driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
With all isdn4linux hardware drivers gone, this is only a wrapper around
CAPI to support old user space. However, from looking at the mailing
list, it seems that the last time anyone asked about it was in 2014,
when the upgrade from a linux-2.4 installation failed, and mISDN was
suggested as a replacement.
The largest public ISDN network (Deutsche Telekom) was supposed to be
shut down 2018, which must have drastically reduced the number of legacy
installations.
When we last discussed removing i4l in 2016, Karsten Keil suggested
revisiting this in 2018. I guess this is overdue.
Link: http://listserv.isdn4linux.de/pipermail/isdn4linux/2014-October/006165.html
Link: https://patchwork.kernel.org/patch/8484861/#17900371
Link: https://listserv.isdn4linux.de/pipermail/isdn4linux/2019-April/thread.html
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
With the decline of ISDN, this seems to have become almost completely
obsolete, and even in the past years before that, almost all remaining
users appear to have used mISDN instead.
Birger Harzenetter noted that he is still using i4l/hisax to take
advantage of the 'divert' driver for call diversion, but otherwise uses
mISDN on the same hardware. This is a rare edge case as far as I
can tell, but we are still breaking an actively used work flow
(see https://xkcd.com/1172/).
We debated moving i4l/hisax to staging as an intermediate step, but as
he is not likely to change the setup, and that would just delay breaking
this use case. The alternatives here are to stay on stable kernels
< 5.2, to create an external driver repository for isdn4linux, or to
add divert functionality to mISDN.
Cc: Birger Harzenetter <WIMPy@yeti.dk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
isdn4linux is getting removed, and the gigaset driver can still
use the CAPI support, so this can all go away.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The ram pstore backend has always had the crash dumper frontend enabled
unconditionally. However, it was possible to effectively disable it
by setting a record_size=0. All the machinery would run (storing dumps
to the temporary crash buffer), but 0 bytes would ultimately get stored
due to there being no przs allocated for dumps. Commit 89d328f637
("pstore/ram: Correctly calculate usable PRZ bytes"), however, assumed
that there would always be at least one allocated dprz for calculating
the size of the temporary crash buffer. This was, of course, not the
case when record_size=0, and would lead to a NULL deref trying to find
the dprz buffer size:
BUG: unable to handle kernel NULL pointer dereference at (null)
...
IP: ramoops_probe+0x285/0x37e (fs/pstore/ram.c:808)
cxt->pstore.bufsize = cxt->dprzs[0]->buffer_size;
Instead, we need to only enable the frontends based on the success of the
prz initialization and only take the needed actions when those zones are
available. (This also fixes a possible error in detecting if the ftrace
frontend should be enabled.)
Reported-and-tested-by: Yaro Slav <yaro330@gmail.com>
Fixes: 89d328f637 ("pstore/ram: Correctly calculate usable PRZ bytes")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Add Vasily Gorbik and Christian Borntraeger as additional maintainers
for s390.
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
After two decades of significant contributions to the s390
architecture, we must say goodbye to our dear colleague.
Blue skies, Martin!
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Some small things were missed with recent name changes
from i40e to iavf. Having a separate patch allows to
correct the small misses in one place.
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Renaming remaining defines from i40e to iavf
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There were a couple of erroneously missed i40e names to
update to iavf left after the larger chunks. Updated them
separately so now they should all be aligned as iavf.
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The defines in iavf_client.h were still vastly i40e, and they
should be iavf.
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
rename the flags inside of iavf_status from I40E_*
to IAVF_*
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>