The cckswing tables cckswing_table_ch1ch13 and cckswing_table_ch14 are
u8 array in little-endian order. To compare four u8 value with register
u32 value, cast the value to cpu order.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ofdm_index_old[] is the index of ofdmswing_table[], and used to indicate
initial value of ROFDM0_X{A,B}TXIQIMBALANCE in rtl8192de_phy_reg_2tarray[]
table, and the initial value is corresponding to calibration thermal value
written in efuse, namely rtlefuse->eeprom_thermalmeter. Then, local
variable ofdm_index_old[] save to rtlpriv->dm.ofdm_index[] for operational
use.
If thermal value (temperature) is increasing, output TX power is lower.
So, we calculate the delta between current and calibration thermal value,
then add power to yield expected and the same output TX power.
Thus, ofdm_index[] should be initialized as rtlpriv->dm.ofdm_index[], and
shift to proper index depends on delta of thermal value. Then, new power
value ofdmswing_table[ofdm_index[]] is written to register.
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This can reduce code size 264 bytes, and make code more readable.
text data bss dec hex filename
Before: 13586 0 16 13602 3522 rtl8192de/dm.o
After: 13322 0 16 13338 341a rtl8192de/dm.o
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This commit doesn't change logic at all. Since indentation is lower, the
wrapped statements can be put in single line that will become more
readable.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes an issue with wpa_supplicant dropping all scan
results because their where considered to be "too old" (e.g.:
"skip - scan result not recent enough (121056.086325 seconds too old)")
which is very weird because this looks like that the scan results have
been received before a scan started. This is due to the inaccuracy of
the default timing mechanism for calculating the BSS entry age.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes a crash that got introduced when the
mentioned patch replaced the direct list_head access
with skb_peek_tail(). When the device is starting up,
there are no entries in the queue, so previously to
"Use skb_peek_tail() instead..." the target_skb would
end up as the tail and head pointer which then could
be used by __skb_queue_after to fill the empty queue.
With skb_peek_tail() in its place will instead just
return NULL which then causes a crash in the
__skb_queue_after().
| BUG: unable to handle kernel NULL pointer dereference at 000000
| #PF error: [normal kernel read fault]
| PGD 0 P4D 0
| Oops: 0000 [#1] SMP PTI
| CPU: 0 PID: 12 Comm: kworker/0:1 Tainted: GO 5.1.0-rc7-wt+ #218
| Hardware name: MSI MS-7816/Z87-G43 (MS-7816), BIOS V1.11 05/09/2015
| Workqueue: events request_firmware_work_func
| RIP: 0010:p54_tx_pending+0x10f/0x1b0 [p54common]
| Code: 78 06 80 78 28 00 74 6d <48> 8b 07 49 89 7c 24 08 49 89 04 24 4
| RSP: 0018:ffffa81c81927d90 EFLAGS: 00010086
| RAX: ffff9bbaaf131048 RBX: 0000000000020670 RCX: 0000000000020264
| RDX: ffff9bbaa976d660 RSI: 0000000000000202 RDI: 0000000000000000
| RBP: ffff9bbaa976d620 R08: 00000000000006c0 R09: ffff9bbaa976d660
| R10: 0000000000000000 R11: ffffe8480dbc5900 R12: ffff9bbb45e87700
| R13: ffff9bbaa976d648 R14: ffff9bbaa976d674 R15: ffff9bbaaf131048
| FS: 0000000000000000(0000) GS:ffff9bbb5ec00000(0000) knlGS:00000
| CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
| CR2: 0000000000000000 CR3: 00000003695fc003 CR4: 00000000001606f0
| Call Trace:
| p54_download_eeprom+0xbe/0x120 [p54common]
| p54_read_eeprom+0x7f/0xc0 [p54common]
| p54u_load_firmware_cb+0xe0/0x160 [p54usb]
| request_firmware_work_func+0x42/0x80
| process_one_work+0x1f5/0x3f0
| worker_thread+0x28/0x3c0
Cc: stable@vger.kernel.org
Fixes: e3554197fc ("p54: Use skb_peek_tail() instead of direct head pointer accesses.")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function strcpy() is inherently not safe. Though the function
works without problems here, it would be better to use other safer
function, e.g. strlcpy(), to replace strcpy() still.
Signed-off-by: Neo Jou <neojou@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
CONFIG_BRCMDBG selects WANT_DEV_COREDUMP but is only used by
brcmfmac so reflect that in the Kconfig.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The number of Kconfig items related to brcmfmac is considerable and
upcoming changes will add some more so it seems good idea to have
a separate Kconfig file for brcmfmac.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With ISC license text in place under the LICENSES folder switch
to using the SPDX license identifier to refer to the ISC license.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With ISC license text in place under the LICENSES folder switch
to using the SPDX license identifier to refer to the ISC license.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With ISC license text in place under the LICENSES folder switch
to using the SPDX license identifier to refer to the ISC license.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With ISC license text in place under the LICENSES folder switch
to using the SPDX license identifier to refer to the ISC license.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With recent ti-sysc driver changes, we can now finally probe most
modules without needing the custom ti,hwmods property.
Let's drop it for omap4 MMC as we can test that for runtime PM
for core retention idle mode for wlcore WLAN.
Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh@kernel.org>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like we currently only detect UART on omap36xx, let's also
add support for omap34xx. And let's also fix the SWSUP mode, it should
be SWSUP_SIDLE for omap3, not SWSUP_SIDLE_ACT like for omap4 and later.
Note that we are still booting omap3 for most part without ti-sysc,
so no need to treat this change as a fix.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With recent ti-sysc driver changes, we can now finally probe most
modules without needing the custom ti,hwmods property.
Let's start with omap4 uart as we can test that for runtime PM
for core retention idle mode.
Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh@kernel.org>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to deassert rstctrl resets before enabling clocks to avoid clock
"failed to enable" errors. For asserting rstctrl reset, the clocks need
to be enabled.
As the reset controller status is not available for arrays, let's use
devm_reset_control_get_optional() so we can get the status after reset.
Note that depends on a proper PRM rstctrl driver, so far I've only
tested this with earlier reset-simple patches.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We must not assert reset for modules with no child device drivers
until in runtime_suspend. Otherwise register access will fail without
legacy mode helping us.
Let's add a flag for disable_on_idle and move the reset driver
handling to runtime suspend and resume. We can then also use the
disable_on_idle flag to reconfigure sysconfig register for PM
modes requesting it.
Let's also make the other flags use bitfield while at it instead of
bool.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some modules have ENAWAKEUP bit that we need to configure when not
relying on platform data callbacks.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some modules have idlemodes wired, but not completely functional. We have
quirks for SWSUP_SIDLE and SWSUP_SIDLE_ACT to manage interconnect target
modules without hardware support, but we've been only using them so far
in legacy mode. Let's add support for SWSUP quirks in non-legacy mode too.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For interconnect target modules with autoidle bit wired, we need to manage
it for enable and disable.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to specify QUIRK_LEGACY_IDLE for device drivers that still have
pm_runtime_irq_safe() set like 8250.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We've had minimal OCP softreset support in ti-sysc interconnect target
module driver only used for MCAN driver so far. But it turns out that
MCAN has the sysstatus register resetdone bit inverted compared to most
other modules.
Let's make OCP softreset work for other typical cases with reset status
in sysstatus or sysconfig register so we can use the new functions for
sysc_enable_module() and sysc_disable_module() without "ti,hwmods"
property in the following patches.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to also support 16-bit writes for i2c in addition to the reads
when we start configuring the sysconfig register for reset and idle modes.
Note that only i2c revision register has LO and HI registers, so let's
add a check also for 16-bit register read. This change is currently cosmetic
and does not affect anything until we enable the module specific quirk
handling for i2c reset and enable later on.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to let ti-sysc driver manage clockdomain autoidle for the
duration of of reset, enable and idle. And we need to do it before we
enable the clock and after we disable it. Currently we are still
relying on platform callbacks indirectly managing clockdomain autoidle.
But I noticed that for device tree only probed drivers it now happens
only after we enabling the clocks and before we disable the clocks,
while it should be the other way around. So far I have not noticed
any issues with this though.
Let's add new ti_sysc_clkdm_deny_idle() and ti_sysc_clkdm_allow_idle()
functions for ti-sysc driver to use to manage clockdomains directly via
platform data callbacks. Note that we can implement the clockdomain
functions in pdata-quirks.c as for probing devices without "ti,hwmods"
custom property we don't need to use the other platform data callbacks.
Let's do this in one patch as there's is still an unlikely chance we
may need to apply this as a fix for v5.2 for dropping legacy platform
data for some devices. We also do have the option of adding back the
platform data if needed in case of trouble.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For old commands, it's fine to have .type = NLA_UNSPEC and it
behaves the same as NLA_MIN_LEN. However, for new commands with
strict validation this is no longer true, and for policy export
to userspace these are also ignored.
Fix up the remaining ones that don't have a type.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The LPS represents Leisure Power Save. When enabled, firmware will be in
charge of turning radio off between beacons. Also firmware should turn
on the radio when beacon is coming, and the data queued should be
transmitted in TBTT period.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Dump warning messages when we get a q_mapping larger than the AC
numbers. And pick BE queue as default.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AC numbers are defined as enum in mac80211, use them instead of bare
0-3 indexing.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
An old optimisation to reduce the number of atomics per batch sadly
relies on struct_mutex for coordination. In order to remove struct_mutex
from serialising object/context closing, always taking and releasing an
active reference on first use / last use greatly simplifies the locking.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528092956.14910-15-chris@chris-wilson.co.uk
Rename the engine this HW context is currently active upon (that we are
flying upon) to disambiguate between the mixture of different active
terms (and prevent conflict in future patches).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528092956.14910-14-chris@chris-wilson.co.uk
Use the per-object local lock to control the cache domain of the
individual GEM objects, not struct_mutex. This is a huge leap forward
for us in terms of object-level synchronisation; execbuffers are
coordinated using the ww_mutex and pread/pwrite is finally fully
serialised again.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528092956.14910-10-chris@chris-wilson.co.uk
Out scatterlist utility routines can be pulled out of i915_gem.h for a
bit more decluttering.
v2: Push I915_GTT_PAGE_SIZE out of i915_scatterlist itself and into the
caller.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528092956.14910-9-chris@chris-wilson.co.uk
Currently the code for manipulating the pages on an object is still
residing in i915_gem.c, move it to i915_gem_object.c
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528092956.14910-3-chris@chris-wilson.co.uk
For convenience in avoiding inline spaghetti, keep the type definition
as a separate header.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528092956.14910-1-chris@chris-wilson.co.uk
Fix sparse warnings:
drivers/net/wireless/realtek/rtw88/phy.c:851:4: warning: symbol 'rtw_cck_size' was not declared. Should it be static?
drivers/net/wireless/realtek/rtw88/phy.c:852:4: warning: symbol 'rtw_ofdm_size' was not declared. Should it be static?
drivers/net/wireless/realtek/rtw88/phy.c:853:4: warning: symbol 'rtw_ht_1s_size' was not declared. Should it be static?
drivers/net/wireless/realtek/rtw88/phy.c:854:4: warning: symbol 'rtw_ht_2s_size' was not declared. Should it be static?
drivers/net/wireless/realtek/rtw88/phy.c:855:4: warning: symbol 'rtw_vht_1s_size' was not declared. Should it be static?
drivers/net/wireless/realtek/rtw88/phy.c:856:4: warning: symbol 'rtw_vht_2s_size' was not declared. Should it be static?
drivers/net/wireless/realtek/rtw88/fw.c:11:6: warning: symbol 'rtw_fw_c2h_cmd_handle_ext' was not declared. Should it be static?
drivers/net/wireless/realtek/rtw88/fw.c:50:6: warning: symbol 'rtw_fw_send_h2c_command' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When building with -Wuninitialized, Clang warns:
drivers/net/wireless/rsi/rsi_91x_sdio.c:940:43: warning: variable 'data'
is uninitialized when used here [-Wuninitialized]
put_unaligned_le32(TA_HOLD_THREAD_VALUE, data);
^~~~
drivers/net/wireless/rsi/rsi_91x_sdio.c:930:10: note: initialize the
variable 'data' to silence this warning
u8 *data;
^
= NULL
1 warning generated.
Using Clang's suggestion of initializing data to NULL wouldn't work out
because data will be dereferenced by put_unaligned_le32. Use kzalloc to
properly initialize data, which matches a couple of other places in this
driver.
Fixes: e5a1ecc97e ("rsi: add firmware loading for 9116 device")
Link: https://github.com/ClangBuiltLinux/linux/issues/464
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>