Bspec describes that GEN10 only supports capability of YUV 4:2:0 output to
HDMI port and GEN11 supports capability of YUV 4:2:0 output to both DP and
HDMI ports.
v2: Minor style fix.
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190521121721.32010-7-gwan-gyeong.mun@intel.com
Data M/N calculations were assumed a bpp as RGB format. But when we are
using YCbCr 4:2:0 output format on DP, we should change bpp calculations
as YCbCr 4:2:0 format. The pipe_bpp value was assumed RGB format,
therefore, it was multiplied with 3. But YCbCr 4:2:0 requires a multiplier
value to 1.5.
Therefore we need to divide pipe_bpp to 2 while DP output uses YCbCr4:2:0
format.
- RGB format bpp = bpc x 3
- YCbCr 4:2:0 format bpp = bpc x 1.5
But Link M/N values are calculated and applied based on the Full Clock for
YCbCr 4:2:0. And DP YCbCr 4:2:0 does not need to pixel clock double for
a dotclock caluation. Only for HDMI YCbCr 4:2:0 needs to pixel clock double
for a dot clock calculation.
It only affects dp and edp port which use YCbCr 4:2:0 output format.
And for now, it does not consider a use case of DSC + YCbCr 4:2:0.
v2:
Addressed review comments from Ville.
Remove a changing of pipe_bpp on intel_ddi_set_pipe_settings().
Because the pipe is running at the full bpp, keep pipe_bpp as RGB
even though YCbCr 4:2:0 output format is used.
Add a link bandwidth computation for YCbCr4:2:0 output format.
v3:
Addressed reivew comments from Ville.
In order to make codes simple, it adds and uses intel_dp_output_bpp()
function.
v6:
Link M/N values are calculated and applied based on the Full Clock for
YCbCr420. The Bit per Pixel needs to be adjusted for YUV420 mode as it
requires only half of the RGB case.
- Link M/N values are calculated and applied based on the Full Clock
- Data M/N values needs to be calculated considering the data is half
due to subsampling
Remove a doubling of pixel clock on a dot clock calculator for
DP YCbCr 4:2:0.
Rebase and remove a duplicate setting of vsc_sdp.DB17.
Add a setting of dynamic range bit to vsc_sdp.DB17.
Change Content Type bit to "Graphics" from "Not defined".
Change a dividing of pipe_bpp to muliplying to constant values on a
switch-case statement.
v7:
Addressed review comments from Ville.
Move a setting of dynamic range bit and a setting of bpc which is based
on pipe_bpp to a "drm/i915/dp: Program VSC Header and DB for Pixel
Encoding/Colorimetry Format" commit.
Change Content Type bit to "Not defined" from "Graphics".
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190521121721.32010-6-gwan-gyeong.mun@intel.com
When YCBCR 4:2:0 outputs is used for DP, we should program YCBCR 4:2:0 to
MSA and VSC SDP.
As per DP 1.4a spec section 2.2.4.3 [MSA Field for Indication of Color
Encoding Format and Content Color Gamut] while sending YCBCR 420 signals
we should program MSA MISC1 fields which indicate VSC SDP for the Pixel
Encoding/Colorimetry Format.
v2: Block comment style fix.
v6:
Fix an wrong setting of MSA MISC1 fields for Pixel Encoding/Colorimetry
Format indication. As per DP 1.4a spec Table 2-96 [MSA MISC1 and MISC0
Fields for Pixel Encoding/Colorimetry Format Indication]
When MISC1, bit 6, is Set to 1, a Source device uses a VSC SDP to
indicate the Pixel Encoding/Colorimetry Format. On the wrong version
it set a bit 5 of MISC1, now it set a bit 6 of MISC1.
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190521121721.32010-5-gwan-gyeong.mun@intel.com
Function intel_pixel_encoding_setup_vsc handles vsc header and data block
setup for pixel encoding / colorimetry format.
Setup VSC header and data block in function intel_pixel_encoding_setup_vsc
for pixel encoding / colorimetry format as per dp 1.4a spec,
section 2.2.5.7.1, table 2-119: VSC SDP Header Bytes, section 2.2.5.7.5,
table 2-120:VSC SDP Payload for DB16 through DB18.
v2:
Minor style fix. [Maarten]
Refer to commit ids instead of patchwork. [Maarten]
v6: Rebase
v7:
Rebase and addressed review comments from Ville.
Use a structure initializer instead of memset().
Fix non-standard comment format.
Remove a referring to specific commit.
Add a setting of dynamic range bit to vsc_sdp.DB17.
Add a setting of bpc which is based on pipe_bpp.
Remove duplicated checking of connector's ycbcr_420_allowed from
intel_pixel_encoding_setup_vsc(). It is already checked from
intel_dp_ycbcr420_config().
Remove comments for VSC_SDP_EXTENSION_FOR_COLORIMETRY_SUPPORTED. It is
already implemented on intel_dp_get_colorimetry_status().
v8:
A missing of setting bpc to VSC setup is the pretty fatal case, it
replaces DRM_DEBUG_KMS() to MISSING_CASE(). [Maarten]
v9: Use a changed member name of struct dp_sdp. it renamed to db from DB.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190521121721.32010-4-gwan-gyeong.mun@intel.com
VSC SDP Payload for PSR is one of data block type of SDP (Secondaray Data
Packet). In order to generalize SDP packet structure name, it renames
struct edp_vsc_psr to struct dp_sdp. And each SDP data blocks have
different usages, each SDP type has different reserved data blocks and
Video_Stream_Configuration Extension VESA SDP might use all of Data Blocks
as Extended INFORFRAME Data Byte. so it makes Data Block variables as
array type. And it adds comments of details of DB of VSC SDP Payload
for Pixel Encoding/Colorimetry Format. This comments follows DP 1.4a spec,
section 2.2.5.7.5, chapter "VSC SDP Payload for Pixel Encoding/Colorimetry
Format".
v7: Addressed review comments from Ville.
v9: Rename a member value name DB to db on struct dp_sdp [Laurent]
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190521121721.32010-3-gwan-gyeong.mun@intel.com
This patch checks a support of YCBCR420 outputs on an encoder level.
If the input mode is YCBCR420-only mode then it prepares DP as an YCBCR420
output, else it continues with RGB output mode.
It set output_format to INTEL_OUTPUT_FORMAT_YCBCR420 in order to using
a pipe scaler as RGB to YCbCr 4:4:4.
v2:
Addressed review comments from Ville.
Style fixed with few naming.
%s/config/crtc_state/
%s/intel_crtc/crtc/
If lscon is active, it makes not to call intel_dp_ycbcr420_config()
to avoid to clobber of lspcon_ycbcr420_config() routine.
And it move the 420_only check into the intel_dp_ycbcr420_config().
v3: Fix uninitialized return value and it is reported by Dan Carpenter.
v4:
Addressed review comments from Ville.
In order to avoid the extra indentation, it inverts if-clause on
intel_dp_ycbcr420_config().
Remove the error print where no errors print are allowed.
v6: Rebase
v7:
Move intel_dp_get_colorimetry_status() to intel_dp from intel_psr.
intel_dp_get_colorimetry_status() checks
VSC_SDP_EXTENSION_FOR_COLORIMETRY_SUPPORTED bit in the
DPRX_FEATURE_ENUMERATION_LIST register.
And intel_dp_ycbcr420_config() uses intel_dp_get_colorimetry_status().
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190521121721.32010-2-gwan-gyeong.mun@intel.com
The hardware automatically zero pads incomplete block ciphers
blocks without raising any errors. This is a screw-up. This
was noticed by CONFIG_CRYPTO_MANAGER_EXTRA_TESTS tests that
sent a incomplete blocks and expect them to fail.
This fixes:
cbc-aes-ppc4xx encryption unexpectedly succeeded on test vector
"random: len=2409 klen=32"; expected_error=-22, cfg="random:
may_sleep use_digest src_divs=[96.90%@+2295, 2.34%@+4066,
0.32%@alignmask+12, 0.34%@+4087, 0.9%@alignmask+1787, 0.1%@+3767]
iv_offset=6"
ecb-aes-ppc4xx encryption unexpectedly succeeded on test vector
"random: len=1011 klen=32"; expected_error=-22, cfg="random:
may_sleep use_digest src_divs=[100.0%@alignmask+20]
dst_divs=[3.12%@+3001, 96.88%@+4070]"
Cc: Eric Biggers <ebiggers@kernel.org>
Cc: stable@vger.kernel.org [4.19, 5.0 and 5.1]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
While the hardware consider them to be blockciphers, the
reference implementation defines them as streamciphers.
Do the right thing and set the blocksize to 1. This
was found by CONFIG_CRYPTO_MANAGER_EXTRA_TESTS.
This fixes the following issues:
skcipher: blocksize for ofb-aes-ppc4xx (16) doesn't match generic impl (1)
skcipher: blocksize for cfb-aes-ppc4xx (16) doesn't match generic impl (1)
Cc: Eric Biggers <ebiggers@kernel.org>
Cc: stable@vger.kernel.org
Fixes: f2a13e7cba ("crypto: crypto4xx - enable AES RFC3686, ECB, CFB and OFB offloads")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch fixes a issue with crypto4xx's ctr(aes) that was
discovered by libcapi's kcapi-enc-test.sh test.
The some of the ctr(aes) encryptions test were failing on the
non-power-of-two test:
kcapi-enc - Error: encryption failed with error 0
kcapi-enc - Error: decryption failed with error 0
[FAILED: 32-bit - 5.1.0-rc1+] 15 bytes: STDIN / STDOUT enc test (128 bits):
original file (1d100e..cc96184c) and generated file (e3b0c442..1b7852b855)
[FAILED: 32-bit - 5.1.0-rc1+] 15 bytes: STDIN / STDOUT enc test (128 bits)
(openssl generated CT): original file (e3b0..5) and generated file (3..8e)
[PASSED: 32-bit - 5.1.0-rc1+] 15 bytes: STDIN / STDOUT enc test (128 bits)
(openssl generated PT)
[FAILED: 32-bit - 5.1.0-rc1+] 15 bytes: STDIN / STDOUT enc test (password):
original file (1d1..84c) and generated file (e3b..852b855)
But the 16, 32, 512, 65536 tests always worked.
Thankfully, this isn't a hidden hardware problem like previously,
instead this turned out to be a copy and paste issue.
With this patch, all the tests are passing with and
kcapi-enc-test.sh gives crypto4xx's a clean bill of health:
"Number of failures: 0" :).
Cc: stable@vger.kernel.org
Fixes: 98e87e3d93 ("crypto: crypto4xx - add aes-ctr support")
Fixes: f2a13e7cba ("crypto: crypto4xx - enable AES RFC3686, ECB, CFB and OFB offloads")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For encryption the destination pointer was still mapped, so the hex dump
may be wrong. The IV still contained the input IV while printing instead
of the output IV as intended.
For decryption the destination pointer was still mapped, so the hex dump
may be wrong. The IV dump was correct.
Do the hex dumps consistenly after the buffers have been unmapped and
in case of IV copied to their final destination.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Selftests report the following:
[ 2.984845] alg: skcipher: cbc-aes-talitos encryption test failed (wrong output IV) on test vector 0, cfg="in-place"
[ 2.995377] 00000000: 3d af ba 42 9d 9e b4 30 b4 22 da 80 2c 9f ac 41
[ 3.032673] alg: skcipher: cbc-des-talitos encryption test failed (wrong output IV) on test vector 0, cfg="in-place"
[ 3.043185] 00000000: fe dc ba 98 76 54 32 10
[ 3.063238] alg: skcipher: cbc-3des-talitos encryption test failed (wrong output IV) on test vector 0, cfg="in-place"
[ 3.073818] 00000000: 7d 33 88 93 0f 93 b2 42
This above dumps show that the actual output IV is indeed the input IV.
This is due to the IV not being copied back into the request.
This patch fixes that.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Crypto self-tests reveal an error:
alg: skcipher: cbc-des3-ccp encryption test failed (wrong output IV) on test vector 0, cfg="in-place"
The offset value should not be recomputed when retrieving the context.
Also, a code path exists which makes decisions based on older (version 3)
hardware; a v3 device deosn't support 3DES so remove this check.
Fixes: 990672d485 ('crypto: ccp - Enable 3DES function on v5 CCPs')
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Updated testmgr will exhibit this error message when loading the
ccp-crypto module:
alg: skcipher: cfb-aes-ccp encryption failed with err -22 on test vector 3, cfg="in-place"
Update the CCP crypto driver to correctly treat CFB as a streaming mode
cipher (instead of block mode). Update the configuration for CFB to
specify the block size as a single byte;
Fixes: 2b789435d7 ('crypto: ccp - CCP AES crypto API support')
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
CFB mode should be treated as a stream cipher, not block.
Fixes: 63b945091a ('crypto: ccp - CCP device driver and interface support')
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix sparse warning:
arch/arm/crypto/sha512-glue.c:40:5: warning:
symbol 'sha512_arm_final' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
FIPS 140-2 section 4.9.2 requires a continuous self test of the noise
source. Up to kernel 4.8 drivers/char/random.c provided this continuous
self test. Afterwards it was moved to a location that is inconsistent
with the FIPS 140-2 requirements. The relevant patch was
e192be9d9a .
Thus, the FIPS 140-2 CTRNG is added to the DRBG when it obtains the
seed. This patch resurrects the function drbg_fips_continous_test that
existed some time ago and applies it to the noise sources. The patch
that removed the drbg_fips_continous_test was
b361476305 .
The Jitter RNG implements its own FIPS 140-2 self test and thus does not
need to be subjected to the test in the DRBG.
The patch contains a tiny fix to ensure proper zeroization in case of an
error during the Jitter RNG data gathering.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Reviewed-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently there is a mismatch b/w the ICID (Isolation Context ID) used
for DMA mapping keys and ICID used for accessing them.
-keys are DMA mapped using a job ring device, thus a job ring ICID
-keys are accessed from descriptors enqueued via Queue Interface,
thus using QI ICID
[Note: ICIDs of JRs, QI are configured by U-boot / other entity by:
-fixing up the corresponding job ring and controller DT nodes
-setting up corresponding caam ICID registers]
In order to avoid IOMMU faults, DMA map the key using the controller
device instead of a job ring device.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When IOMMU is enabled, iova -> phys address translation should be
performed using iommu_ops, not dma_to_phys().
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use the controller device for caam/qi instead of allocating
a new platform device.
This is needed as a preparation to add support for working behind an
SMMU. A platform device allocated using platform_device_register_full()
is not completely set up - most importantly .dma_configure()
is not called.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently we allow top level code, i.e. that which sits between the
low level (HW-specific) drivers and crypto API, to be built as several
drivers: caamalg, caamhash, caam_pkc, caamrng, caamalg_qi.
There is no advantage in this, more it interferes with adding support
for deferred probing (there are no corresponding devices and thus
no bus).
Convert these drivers and call init() / exit() manually at the right
time.
Move algorithms initialization at JR probe / remove time:
-the first probed JR registers the crypto algs
-the last removed JR unregisters the crypto algs
Note: caam_qi_init() is called before JR platform devices creation
(of_populate_bus()), such that QI interface is initialized when
the caam/qi algorithms are registered in the JR driver (by calling
caam_qi_algapi_init().
While here, fix the Kconfig entries under CRYPTO_DEV_FSL_CAAM_JR
to be aligned.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
According to CAAM RM:
-crypto engine reads 4 S/G entries (64 bytes) at a time,
even if the S/G table has fewer entries
-it's the responsibility of the user / programmer to make sure
this HW behaviour has no side effect
The drivers do not take care of this currently, leading to IOMMU faults
when the S/G table ends close to a page boundary - since only one page
is DMA mapped, while CAAM's DMA engine accesses two pages.
Fix this by rounding up the number of allocated S/G table entries
to a multiple of 4.
Note that in case of two *contiguous* S/G tables, only the last table
might needs extra entries.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When enabling IOMMU support, the following issue becomes visible
in the AEAD zero-length case.
Even though the output sequence length is set to zero, the crypto engine
tries to prefetch 4 S/G table entries (since SGF bit is set
in SEQ OUT PTR command - which is either generated in SW in case of
caam/jr or in HW in case of caam/qi, caam/qi2).
The DMA read operation will trigger an IOMMU fault since the address in
the SEQ OUT PTR is "dummy" (set to zero / not obtained via DMA API
mapping).
1. In case of caam/jr, avoid the IOMMU fault by clearing the SGF bit
in SEQ OUT PTR command.
2. In case of caam/qi - setting address, bpid, length to zero for output
entry in the compound frame has a special meaning (cf. CAAM RM):
"Output frame = Unspecified, Input address = Y. A unspecified frame is
indicated by an unused SGT entry (an entry in which the Address, Length,
and BPID fields are all zero). SEC obtains output buffers from BMan as
prescribed by the preheader."
Since no output buffers are needed, modify the preheader by setting
(ABS = 1, ADDBUF = 0):
-"ABS = 1 means obtain the number of buffers in ADDBUF (0 or 1) from
the pool POOL ID"
-ADDBUF: "If ABS is set, ADD BUF specifies whether to allocate
a buffer or not"
3. In case of caam/qi2, since engine:
-does not support FLE[FMT]=2'b11 ("unused" entry) mentioned in DPAA2 RM
-requires output entry to be present, even if not used
the solution chosen is to leave output frame list entry zeroized.
Fixes: 763069ba49 ("crypto: caam - handle zero-length AEAD output")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If a zero length request is submitted through the skcipher api,
do not offload it and return success.
Reviewed-by: Conor Mcloughlin <conor.mcloughlin@intel.com>
Tested-by: Sergey Portnoy <sergey.portnoy@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Return -EINVAL if a request for a block cipher is not multiple of the
size of the block.
This problem was found with by the new extra run-time crypto self test.
Reviewed-by: Conor Mcloughlin <conor.mcloughlin@intel.com>
Tested-by: Sergey Portnoy <sergey.portnoy@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If an invalid key is provided as input to the setkey function, the
function always failed returning -ENOMEM rather than -EINVAL.
Furthermore, if setkey was called multiple times with an invalid key,
the device instance was getting leaked.
This patch fixes the error paths in the setkey functions by returning
the correct error code in case of error and freeing all the resources
allocated in this function in case of failure.
This problem was found with by the new extra run-time crypto self test.
Reviewed-by: Conor Mcloughlin <conor.mcloughlin@intel.com>
Tested-by: Sergey Portnoy <sergey.portnoy@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The block size for aes counter mode was improperly set to AES_BLOCK_SIZE.
This sets it to 1 as it is a stream cipher.
This problem was found with by the new extra run-time crypto self test.
Reviewed-by: Conor Mcloughlin <conor.mcloughlin@intel.com>
Tested-by: Sergey Portnoy <sergey.portnoy@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Allocate a contiguous buffer and instruct the qat hardware to return the
iv at the end of an encryption or decryption operation.
The iv is copied to the array provided by the user in the callback
function.
This problem was found with by the crypto self test.
Reviewed-by: Conor Mcloughlin <conor.mcloughlin@intel.com>
Tested-by: Sergey Portnoy <sergey.portnoy@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The offset is calculated based on type of hash algorithum.
If the algorithum is invalid the offset can have negative value.
Hence added negative offset check and return -EFAULT.
Reviewed-by: Conor Mcloughlin <conor.mcloughlin@intel.com>
Tested-by: Sergey Portnoy <sergey.portnoy@intel.com>
Signed-off-by: Shant KumarX Sonnad <shant.kumarx.sonnad@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
ip_sf_list_clear_all() needs to be defined even if !CONFIG_IP_MULTICAST
Fixes: 3580d04aa6 ("ipv4/igmp: fix another memory leak in igmpv3_del_delrec()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b6664ba42f ("s390, kexec_file: drop arch_kexec_mem_walk()")
changed kexec_add_buffer() to skip searching for a memory location if
kexec_buf.mem is already set, and use the address that is there.
In powerpc code we reuse a kexec_buf variable for loading both the
kernel and the initramfs by resetting some of the fields between those
uses, but not mem. This causes kexec_add_buffer() to try to load the
kernel at the same address where initramfs will be loaded, which is
naturally rejected:
# kexec -s -l --initrd initramfs vmlinuz
kexec_file_load failed: Invalid argument
Setting the mem field before every call to kexec_add_buffer() fixes
this regression.
Fixes: b6664ba42f ("s390, kexec_file: drop arch_kexec_mem_walk()")
Cc: stable@vger.kernel.org # v5.0+
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Reviewed-by: Dave Young <dyoung@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fixes for 5.2:
- Fix for DMCU firmware issues for stable
- Add missing polaris10 pci id to kfd
- Screen corruption fix on picasso
- Fix for driver reload on vega10
- SR-IOV fixes
- Locking fix in new SMU code
- Compute profile switching fix for KFD
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190522205425.3657-1-alexander.deucher@amd.com
- gma500 fix to make lvds detection more reliable
- select devfreq for panfrost since it can't probe without it
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEfxcpfMSgdnQMs+QqlvcN/ahKBwoFAlzlpl0ACgkQlvcN/ahK
Bwp5PAgAnL7n2k7f6ifBhF4h0SLWAGDLNnO1Pmyi5lYQTHSPf66N2xpgatTicMY6
EKVvzsFO3dTFDFbFY3kUC+nuVTaz7NDbPXnVRxiEsIlqoEIII70XHLZJKYdEjkEQ
b2Tueo7lPj6EZjdcOHuErpdd9+Iy4FqPpsNuXz4giBlDU5yVYMgfY/j6EEq7QiSh
N9onTxlSJug/RWtqFx3tGSBxQvLuot+2w3h3i9wIqu/BqjilR1mbmYH9iPULm4wa
CDatEDP3hNSDfQfQTinFpmZR6x29GMGNr4ATBCRCxCupnEofv8eHO1u2cB28sB6s
HQXkBYDaeBIDM3Aozs2A5n89LheG9Q==
=FgtF
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2019-05-22' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
- sun4i fixes to hdmi phy as well as u16 overflow in dsi (left from -next-fixes)
- gma500 fix to make lvds detection more reliable
- select devfreq for panfrost since it can't probe without it
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20190522194440.GA22359@art_vandelay
A set of misc fixes for various issues that have surfaced recently.
All Cc'd stable except the dma iterator fix which shouldn't really cause
any real issues on older kernels.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: "Thomas Hellstrom (VMware)" <thomas@shipmail.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190522115408.33185-1-thomas@shipmail.org
Commit 9cc342f6c4 ("treewide: prefix header search paths with
$(srctree)/") caused a build error for MIPS VDSO.
CC arch/mips/vdso/gettimeofday.o
In file included from ../arch/mips/vdso/vdso.h:26,
from ../arch/mips/vdso/gettimeofday.c:11:
../arch/mips/include/asm/page.h:12:10: fatal error: spaces.h: No such file or directory
#include <spaces.h>
^~~~~~~~~~
The cause of the error is a missing space after the compiler flag -I .
Kbuild used to have a global restriction "no space after -I", but
commit 48f6e3cf5b ("kbuild: do not drop -I without parameter") got
rid of it. Having a space after -I is no longer a big deal as far as
Kbuild is concerned.
It is still a big deal for MIPS because arch/mips/vdso/Makefile
filters the header search paths, like this:
ccflags-vdso := \
$(filter -I%,$(KBUILD_CFLAGS)) \
..., which relies on the assumption that there is no space after -I .
Fixes: 9cc342f6c4 ("treewide: prefix header search paths with $(srctree)/")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
To meet the 'i' (immediate) constraint for the asm operands,
this function must be always inlined.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-kernel@vger.kernel.org
It's easy to have a mismatch of "intended to be public" vs really
exposed API functions. While Makefile does check for this mismatch, if
it actually occurs it's not trivial to determine which functions are
accidentally exposed. This patch dumps out a diff showing what's not
supposed to be exposed facilitating easier fixing.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The Mali GPU is supplied by VDD_EE which is provided by the DCDC2
regulator.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The DCDC2 regulator output is actually called "VDD_EE" in various
Meson8b board schematics. This matches with what Amlogic names it in the
most part of their vendor kernel (there are a few places where it's
actually called VDDAO, schematics of EC-100 suggest that the regulator
output is used for both signals).
While here, also give the regulator an alias as it supplies the Mali GPU
so a phandle to it will be required later on.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The canvas IP on Meson8, Meson8b and Meson8m2 is mostly identical to the
one on GXBB and newer. The only known difference so far is that that the
"endianness" bits are not supported on Meson8m2 and earlier.
Add new compatible strings and a check in meson_canvas_config() to
validate that the endianness bits cannot be configured on the 32-bit
SoCs.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The canvas IP on Meson8, Meson8b and Meson8m2 is similar to the one
found on GXBB and newer. The only known difference is that the older
SoCs cannot configure the "endianness".
Add a compatible string for each of the older SoCs to make sure we won't
be using unsupported features on these SoCs.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the canvas module to Meson8b because it's required for the VPU
(video output) and video decoders.
The canvas module is located inside the "DMC bus" (where also some of
the memory controller registers are located). The "DMC bus" itself is
part of the so-called "MMC bus".
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
With the Meson8m2 SoC the canvas module was moved from offset 0x20
(Meson8) to offset 0x48 (same as on Meson8b). The offsets inside the
canvas module are identical.
Correct the offset so the driver uses the correct registers.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the canvas module to Meson8 because it's required for the VPU
(video output) and video decoders.
The canvas module is located inside thie "DMC bus" (where also some of
the memory controller registers are located). The "DMC bus" itself is
part of the so-called "MMC bus".
Amlogic's vendor kernel has an explicit #define for the "DMC" register
range on Meson8m2 while there's no such #define for Meson8. However, the
canvas and memory controller registers on Meson8 are all expressed as
"0x6000 + actual offset", while Meson8m2 uses "DMC + actual offset".
Thus it's safe to assume that the DMC bus exists on both SoCs even
though the registers inside are slightly different.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Michael Chan says:
===================
bnxt_en: Bug fixes.
There are 4 driver fixes in this series:
1. Fix RX buffer leak during OOM condition.
2. Call pci_disable_msix() under correct conditions to prevent hitting BUG.
3. Reduce unneeded mmeory allocation in kdump kernel to prevent OOM.
4. Don't read device serial number on VFs because it is not supported.
Please queue #1, #2, #3 for -stable as well. Thanks.
===================
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't read DSN on VFs that do not have the PCI capability.
Fixes: 03213a9965 ("bnxt: move bp->switch_id initialization to PF probe")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Skip RDMA context memory allocations, reduce to 1 ring, and disable
TPA when running in the kdump kernel. Without this patch, the driver
fails to initialize with memory allocation errors when running in a
typical kdump kernel.
Fixes: cf6daed098 ("bnxt_en: Increase context memory allocations on 57500 chips for RDMA.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When making configuration changes, the driver calls bnxt_close_nic()
and then bnxt_open_nic() for the changes to take effect. A parameter
irq_re_init is passed to the call sequence to indicate if IRQ
should be re-initialized. This irq_re_init parameter needs to
be included in the bnxt_reserve_rings() call. bnxt_reserve_rings()
can only call pci_disable_msix() if the irq_re_init parameter is
true, otherwise it may hit BUG() because some IRQs may not have been
freed yet.
Fixes: 41e8d79837 ("bnxt_en: Modify the ring reservation functions for 57500 series chips.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>