For 2-stage transfer, some users like Audio still need transaction interrupt
to notify when the 2-stage transfer is completed. Thus we should enable
2-stage transfer interrupt to support this feature.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Move the 2-stage configuration before configuring the link-list mode,
since we will use some 2-stage configuration to fill the link-list
configuration.
Signed-off-by: Eric Long <eric.long@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The maximum value of block length is 0xffff, so if the configured transfer length
is more than 0xffff, that will cause block length overflow to lead a configuration
error.
Thus we can set block length as the maximum burst length to avoid this issue, since
the maximum burst length will not be a big value which is more than 0xffff.
Signed-off-by: Eric Long <eric.long@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The 2-stage destination channel will be triggered by source channel
automatically, which means we should not trigger it by software request.
Signed-off-by: Eric Long <eric.long@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When user terminates one DMA channel to free all its descriptors, but
at the same time one transaction interrupt was triggered possibly, now
we should not handle this interrupt by validating if the 'schan->cur_desc'
was set as NULL to avoid crashing the kernel.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We will get a NULL virtual descriptor by vchan_find_desc() when the descriptor
has been submitted, that will crash the kernel when getting the descriptor
status.
In this case, since the descriptor has been submitted to process, but it
is not completed now, which means the descriptor is listed into the
'vc->desc_submitted' list now. So we can not get current processing descriptor
by vchan_find_desc(), but the pointer 'schan->cur_desc' will point to the
current processing descriptor, then we can use 'schan->cur_desc' to get
current processing descriptor's status to avoid this issue.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Minimum, maximum, and stepsize taken from Silicon Labs reference.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Venus v4 doesn't send ALLOC_MODE property and thus parser doesn't
recognize it as dynamic buffer (for OUTPUT/OUTPUT2 type of buffers)
make it obvious in the helper function.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Patch commit de5a0bafcf ("media: venus: core: correct maximum hardware
load for sdm845") meant to increase the maximum hardware load for sdm845,
but ended up changing the one for msm8996 instead.
Fixes: de5a0bafcf ("media: venus: core: correct maximum hardware load for sdm845")
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
After "5918045c4e drm/scheduler: rework job destruction", lima started
to leak memory due to buffers not being destroyed after job execution in
the drm scheduler.
This started happening because the drm scheduler only destroyed buffers
after cancelling the job timeout handler, and for lima this handler was
never started as lima specified a MAX_SCHEDULE_TIMEOUT timeout.
Lima seems to run well in its current state with a real timeout, so to
make it more aligned with the other drivers from now on, let's use a
real default timeout.
This also fixes the observed memory leaks.
The 500ms value was chosen as it is the current value for all other
embedded gpu drivers using drm sched.
Signed-off-by: Erico Nunes <nunes.erico@gmail.com>
Signed-off-by: Qiang Yu <yuq825@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190520224229.21111-1-nunes.erico@gmail.com
The header report return value from decoder sequence initialization is
available on CodaHx4 and CODA7541 already. Use the profile and level
identification values reported by the firmware to update codec specific
profile and level controls after sequence initialization has succeeded.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When a menu control is updated via s_ctrl, print the corresponding menu
entry string in addition to the numerical value it is set to.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Otherwise the default initialization would always swamp the debug log.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Print a single line containing the following information:
- which frame was decoded, including its type,
- if no frame was decoded, the reason (code) why
- which decoded frame was returned, copied out by either rotator or VODA,
- if no frame was returned, the reason (code) why, and
- the output queue sequence number, which is only useful in case
each queued coded buffer corresponds to exactly one frame.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a function to translate from V4L2 buffer flags to 'I'/'P'/'B'
characters for debug output.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This allows to use coda_debug level 2 for verbose but not quite as
verbose debug logging. Register access level logging is of limited
use anyway, as this includes busy polling of status bits.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In case the sensor refuses to set the format, avoid printing the error
message that no compatible format was found.
This means that the try_fmt will be less verbose.
The error will be printed only if really a format cannot be found.
Some application try all possible formats in a row (gstreamer e.g.)
which will flood the console with error messages until a working one is found.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This adds support for the 'button' control DO_WHITE_BALANCE
This feature will enable the ISC to compute the white balance coefficients
in a one time shot, at the user discretion.
This can be used if a color chart/grey chart is present in front of the camera.
The ISC will adjust the coefficients and have them fixed until next balance
or until sensor mode is changed.
This is particularly useful for white balance adjustment in different
lighting scenarios, and then taking photos to similar scenery.
The old auto white balance stays in place, where the ISC will adjust every
4 frames to the current scenery lighting, if the scenery is approximately
grey in average, otherwise grey world algorithm fails.
One time white balance adjustments needs streaming to be enabled, such that
capture is enabled and the histogram has data to work with.
Histogram without capture does not work in this hardware module.
To start the one time white balance procedure:
v4l2-ctl --set-ctrl=do_white_balance=1
This feature works only if the sensor is streaming RAW data, as the hardware
supports a histogram only for RAW bayer components.
If the auto white balance is enabled, do_white_balance does nothing.
If the streaming is disabled, or the sensor does not output RAW data, the
control is inactive.
User controls now include the do_white_balance ctrl:
User Controls
brightness 0x00980900 (int) : min=-1024 max=1023 step=1 default=0 value=0 flags=slider
contrast 0x00980901 (int) : min=-2048 max=2047 step=1 default=256 value=256 flags=slider
white_balance_automatic 0x0098090c (bool) : default=1 value=0
do_white_balance 0x0098090d (button) : flags=write-only, execute-on-write
gamma 0x00980910 (int) : min=0 max=2 step=1 default=2 value=2 flags=slider
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Control DO_WHITE_BALANCE is a button, with read only and execute-on-write flags.
Adding this control in the proper list in the fill function.
After adding it here, we can see output of v4l2-ctl -L
do_white_balance 0x0098090d (button) : flags=write-only, execute-on-write
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reworked auto white balance feature (awb) to cope with all four channels.
Implemented stretching and grey world algorithms.
Using the histogram, the ISC will auto adjust the white balance during
frame captures.
Because each histogram needs a frame, it will take 4 frames for one adjustment.
When the gains were updated by previous code, the registers for the gains
were updated only on new streaming start. Now, after each full histogram the
registers are updated with new gains.
Also, on previous code, if the streaming stopped but not all 3 histograms
finished, a new histogram was started either way. This used to lead to an
error "timeout to update profile" when streaming was stopped.
According to the hardware, histogram can only work together with the capture,
not independently.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The datasheet states:
Bit 4: ClockEnSet the ClockEn bit high to enable an external clocking
(crystal or clock generator at XIN). Set the ClockEn bit to 0 to disable
clocking
Bit 1: CrystalEnSet the CrystalEn bit high to enable the crystal
oscillator. When using an external clock source at XIN, CrystalEn must
be set low.
The bit 4, MAX310X_CLKSRC_EXTCLK_BIT, should be set and was not.
This was required to make the MAX3107 with an external crystal on our
board able to send or receive data.
Signed-off-by: Joe Burmeister <joe.burmeister@devtank.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As noted in commit 84b40e3b57 ("serial: 8250: omap: Disable DMA for
console UART"), UART console lines use low-level PIO only access functions
which will conflict with use of the line when DMA is enabled, e.g. when
the console line is also used for systemd messages. So disable DMA
support for UART console lines.
Reported-by: Michael Rodin <mrodin@de.adit-jv.com>
Link: https://patchwork.kernel.org/patch/10929511/
Tested-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org
Signed-off-by: George G. Davis <george_davis@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each time the DMA engine signals a transaction error the driver prints
a message at error level. Getting transaction errors is pretty much
expected on baudrate mismatches and the correspoding error counters
are increased in this case properly. Remove the error message which
is possibly repeated at a very high rate which can lock up the whole
system.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the tty layer requests the uart to throttle, the current code
executing in msm_serial will trigger "Bad mode in Error Handler" and
generate an invalid stack frame in pstore before rebooting (that is if
pstore is indeed configured: otherwise the user shall just notice a
reboot with no further information dumped to the console).
This patch replaces the PIO byte accessor with the word accessor
already used in PIO mode.
Fixes: 68252424a7 ("tty: serial: msm: Support big-endian CPUs")
Cc: stable@vger.kernel.org
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
st.c is the only st file missing licensing information. Add a
GPLv2 tag for the default kernel license.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
sr.c is the only sr file missing licensing information. Add a
GPLv2 tag for the default kernel license.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the the GPLv2+ SPDX tag instead of verbose boilerplate text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the the GPLv2 SPDX tag instead of verbose boilerplate text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the the GPLv2 SPDX tag instead of verbose boilerplate text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
sd.c is the only sd file missing licensing information. Add a
GPLv2 tag for the default kernel license.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the the GPLv2 SPDX tag instead of verbose boilerplate text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the the GPLv2+ SPDX tag instead of verbose boilerplate text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
sas_task.c is the only libsas file missing licensing information. Add a
GPLv2 tag for the default kernel license.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the the GPLv2+ SPDX tag instead of verbose boilerplate text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the the GPLv2 SPDX tag instead of verbose boilerplate text.
[mkp: fixed comment syntax on *.c]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the the GPLv2 SPDX tag instead of verbose boilerplate text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The libfc uapi headers already have proper SPDX tags, remove the
duplicate boilerplate text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the the GPLv2+ SPDX tag instead of verbose boilerplate text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the the GPLv2+ SPDX tag instead of verbose boilerplate text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the the GPLv2 SPDX tag instead of a free form blurb.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the the GPLv2+ SPDX tag instead of verbose boilerplate text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the the GPLv2+ SPDX tag instead of verbose boilerplate text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The FC transport class uapi headers already have proper SPDX tags,
remove the duplicate boilerplate text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the the GPLv2+ SPDX tag instead of verbose boilerplate text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The SCSI netlink uapi header already has a proper SPDX tag, remove the
duplicate boilerplate text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>