Commit graph

982,081 commits

Author SHA1 Message Date
Sven Eckelmann
b037b10756 ath9k: Differentiate between max combined and per chain power
The ath9k driver uses as maximum allowed txpower the constant
MAX_RATE_POWER. It is used to set a maximum txpower limit for the PHY
(which is combined txpower) and also the maximum txpower for per chain
rates. Its value 63 is derived from the maximum number the registers can
store for the per chain txpower.

The max txpower a user can set because of this is 31 dBm (floor(63 / 2)).
This also means that a device with multiple tx chains is even limited
further:

* 1 chain:  31 dBm per chain
* 2 chains: 28 dBm per chain
* 3 chains: 26 dBm per chain

This combined txpower limit of 31 dBm becomes even more problematic when
some extra antenna gain is set in the EEPROM. A high power device is then
no longer able to reach its potential limits.

Instead the code dealing with the combined txpower must use a higher limit
than 63 and only the code dealing with the per chain txpower have to use
the limit of 63. Since the antenna gain can be quite large and 8 bit
variables are often used in ath9k for txpower, a large, divisible by two
number like 254 is a good choice for this new limit.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-29 17:53:43 +03:00
Tim Schumacher
2f90c7e5d0 ath9k: Check for errors when reading SREV register
Right now, if an error is encountered during the SREV register
read (i.e. an EIO in ath9k_regread()), that error code gets
passed all the way to __ath9k_hw_init(), where it is visible
during the "Chip rev not supported" message.

    ath9k_htc 1-1.4:1.0: ath9k_htc: HTC initialized with 33 credits
    ath: phy2: Mac Chip Rev 0x0f.3 is not supported by this driver
    ath: phy2: Unable to initialize hardware; initialization status: -95
    ath: phy2: Unable to initialize hardware; initialization status: -95
    ath9k_htc: Failed to initialize the device

Check for -EIO explicitly in ath9k_hw_read_revisions() and return
a boolean based on the success of the operation. Check for that in
__ath9k_hw_init() and abort with a more debugging-friendly message
if reading the revisions wasn't successful.

    ath9k_htc 1-1.4:1.0: ath9k_htc: HTC initialized with 33 credits
    ath: phy2: Failed to read SREV register
    ath: phy2: Could not read hardware revision
    ath: phy2: Unable to initialize hardware; initialization status: -95
    ath: phy2: Unable to initialize hardware; initialization status: -95
    ath9k_htc: Failed to initialize the device

This helps when debugging by directly showing the first point of
failure and it could prevent possible errors if a 0x0f.3 revision
is ever supported.

Signed-off-by: Tim Schumacher <timschumi@gmx.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-29 17:52:55 +03:00
Toke Høiland-Jørgensen
389b72e582 ath9k: Don't trust TX status TID number when reporting airtime
As already noted a comment in ath_tx_complete_aggr(), the hardware will
occasionally send a TX status with the wrong tid number. If we trust the
value, airtime usage will be reported to the wrong AC, which can cause the
deficit on that AC to become very low, blocking subsequent attempts to
transmit.

To fix this, account airtime usage to the TID number from the original skb,
instead of the one in the hardware TX status report.

Reported-by: Miguel Catalan Cid <miguel.catalan@i2cat.net>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-29 17:51:49 +03:00
Colin Ian King
e643da21e1 ath6kl: remove redundant check of status != 0
The check on status not being zero is redundant as previous code
paths that set status to an error value break out of the while
loop and hence status is never non-zero at the check. Remove
this redundant code.

Addresses-Coverity: ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-29 17:50:10 +03:00
Dan Carpenter
5d6751eaff ath6kl: add some bounds checking
The "ev->traffic_class" and "reply->ac" variables come from the network
and they're used as an offset into the wmi->stream_exist_for_ac[] array.
Those variables are u8 so they can be 0-255 but the stream_exist_for_ac[]
array only has WMM_NUM_AC (4) elements.  We need to add a couple bounds
checks to prevent array overflows.

I also modified one existing check from "if (traffic_class > 3) {" to
"if (traffic_class >= WMM_NUM_AC) {" just to make them all consistent.

Fixes: bdcd817079 (" Add ath6kl cleaned up driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-29 17:49:16 +03:00
Joel Fernandes (Google)
bc0c60457c init/config: Do not select BUILD_BIN2C for IKCONFIG
Since commit 13610aa908 ("kernel/configs: use .incbin directive to
embed config_data.gz"), IKCONFIG no longer uses BUILD_BIN2C so prevent
it from being selected in Kconfig.

Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-29 16:48:04 +02:00
Joel Fernandes (Google)
43d8ce9d65 Provide in-kernel headers to make extending kernel easier
Introduce in-kernel headers which are made available as an archive
through proc (/proc/kheaders.tar.xz file). This archive makes it
possible to run eBPF and other tracing programs that need to extend the
kernel for tracing purposes without any dependency on the file system
having headers.

A github PR is sent for the corresponding BCC patch at:
https://github.com/iovisor/bcc/pull/2312

On Android and embedded systems, it is common to switch kernels but not
have kernel headers available on the file system. Further once a
different kernel is booted, any headers stored on the file system will
no longer be useful. This is an issue even well known to distros.
By storing the headers as a compressed archive within the kernel, we can
avoid these issues that have been a hindrance for a long time.

The best way to use this feature is by building it in. Several users
have a need for this, when they switch debug kernels, they do not want to
update the filesystem or worry about it where to store the headers on
it. However, the feature is also buildable as a module in case the user
desires it not being part of the kernel image. This makes it possible to
load and unload the headers from memory on demand. A tracing program can
load the module, do its operations, and then unload the module to save
kernel memory. The total memory needed is 3.3MB.

By having the archive available at a fixed location independent of
filesystem dependencies and conventions, all debugging tools can
directly refer to the fixed location for the archive, without concerning
with where the headers on a typical filesystem which significantly
simplifies tooling that needs kernel headers.

The code to read the headers is based on /proc/config.gz code and uses
the same technique to embed the headers.

Other approaches were discussed such as having an in-memory mountable
filesystem, but that has drawbacks such as requiring an in-kernel xz
decompressor which we don't have today, and requiring usage of 42 MB of
kernel memory to host the decompressed headers at anytime. Also this
approach is simpler than such approaches.

Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-29 16:48:03 +02:00
Gustavo A. R. Silva
83d9562b64 ath6kl: wmi: use struct_size() helper
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.

So, replace code of the following form:

sizeof(*ev) + ev->num_neighbors * sizeof(struct wmi_neighbor_info)

with:

struct_size(ev, neighbor, ev->num_neighbors)

This code was detected with the help of Coccinelle.

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-29 17:47:03 +03:00
Rasmus Villemoes
12eade123e irqchip/gic-v3-its: Make free_lpi_range a little cheaper
Using list_add + list_sort to insert an element and keeping the list
sorted is a somewhat blunt instrument; one can find the right place to
insert in fewer lines of code than the cmp callback uses. Moreover,
walking the entire list afterwards to merge adjacent ranges is
overkill, since we know that only the just-inserted element may be
merged with its neighbours.

Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2019-04-29 15:45:01 +01:00
Rasmus Villemoes
1c73fac50d irqchip/gic-v3-its: Drop redundant initialization in mk_lpi_range
There's no reason to ask kmalloc() to zero the allocation, since all
the fields get initialized immediately afterwards. Except that there's
also not any reason to initialize the ->entry member, since the
element gets added to the lpi_range_list immediately.

Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2019-04-29 15:45:01 +01:00
Rasmus Villemoes
b31a383852 irqchip/gic-v3-its: Move allocation outside mutex
There's no reason to do the allocation of the new lpi_range inside the
lpi_range_lock. One could change the code to avoid the allocation
altogether in case the freed range can be merged with one or two
existing ranges (in which case the allocation would naturally be done
under the lock), but it's probably not worth complicating the code for
that.

Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2019-04-29 15:45:01 +01:00
Fabien Dessenne
cfbf9e4970 irqchip/stm32: Use a platform driver for stm32mp1-exti device
This irqchip driver uses the hwspinlock framework (coprocessor HW regs
access concurrency) for the stm32mp1-exti device.
Hence, this driver needs to handle the hwspinlock driver dependency
using the deferred probe mechanism which requires to move this driver
into a platform one with a probe() ops.
This applies only for the device which is "st,stm32mp1-exti" compatible,
the management of the other devices (st,stm32h7-exti / st,stm32-exti) is
kept unchanged (use IRQCHIP_DECLARE)

Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2019-04-29 15:45:01 +01:00
Sameer Pujar
960164f714 irqchip/gic-pm: Fix suspend handling
If interrupts are enabled for a non-root GIC device that uses the
gic-pm driver, when system suspend occurs, the current interrupt
state is not saved and restored correctly and so interrupts do not
work again on resuming the system. Add a late suspend handler to
save and restore the state for these devices.

Suggested-by: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2019-04-29 15:45:01 +01:00
Sameer Pujar
fe00f8900c irqchip/gic-pm: Update driver to use clk_bulk APIs
gic-pm driver is using pm-clk framework to manage clock resources, where
clocks remain always ON. This happens on Tegra devices which use BPMP
co-processor to manage the clocks. Calls to BPMP are always blocking and
hence it is necessary to enable/disable clocks during prepare/unprepare
phase respectively. When pm-clk is used, prepare count of clock is not
balanced until pm_clk_remove() happens. Clock is prepared in the driver
probe() and thus prepare count of clock remains non-zero, which in turn
keeps clock ON always.

Please note that above mentioned behavior is specific to Tegra devices
using BPMP for clock management and this should not be seen on other
devices. Though this patch uses clk_bulk APIs to address the mentioned
behavior, this works fine for all devices.

To simplify gic_get_clocks() API is removed and instead probe can do
necessary setup.

Suggested-by: Mohan Kumar D <mkumard@nvidia.com>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2019-04-29 15:45:01 +01:00
Julien Grall
08970ecf74 irq/irqdomain: Fix typo in the comment on top of __irq_domain_alloc_irqs()
The word 'number' has been misspelt in the comment on top of
_irq_domain_alloc_irqs().

Signed-off-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2019-04-29 15:45:00 +01:00
Anson Huang
358b9d248a irqchip/imx-irqsteer: Use devm_platform_ioremap_resource() to simplify code
Use the new helper devm_platform_ioremap_resource() which wraps the
platform_get_resource() and devm_ioremap_resource() together, to
simplify the code.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2019-04-29 15:45:00 +01:00
Julien Grall
a7c90f51d7 irqchip/gic-v3-its: Fix typo in a comment in its_msi_prepare()
The word 'entirely' has been misspelt in a comment in its_msi_prepare().

Signed-off-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2019-04-29 15:45:00 +01:00
Hongbo Yao
0f29456d08 irqchip/gic-v3-its: fix some definitions of inner cacheability attributes
Some definitions of Inner Cacheability attibutes need to be corrected.

Fixes: 8c828a535e ("irqchip/gicv3-its: Restore all cacheability attributes")
Signed-off-by: Hongbo Yao <yaohongbo@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2019-04-29 15:44:45 +01:00
Gustavo A. R. Silva
df75786b92 ath6kl: debug: Use struct_size() helper
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.

So, change the following form:

sizeof(*tbl) + num_entries * sizeof(struct wmi_bss_roam_info)

 to :

struct_size(tbl, info, num_entries)

This code was detected with the help of Coccinelle.

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-29 17:43:35 +03:00
Pradeep kumar Chitrapu
93ee3d108f ath10k: fix incorrect multicast/broadcast rate setting
Invalid rate code is sent to firmware when multicast rate value of 0 is
sent to driver indicating disabled case, causing broken mesh path.
so fix that.

Tested on QCA9984 with firmware 10.4-3.6.1-00827

Sven tested on IPQ4019 with 10.4-3.5.3-00057 and QCA9888 with 10.4-3.5.3-00053
(ath10k-firmware) and 10.4-3.6-00140 (linux-firmware 2018-12-16-211de167).

Fixes: cd93b83ad9 ("ath10k: support for multicast rate control")
Co-developed-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Tested-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-29 17:42:32 +03:00
Wen Gong
a8b10da05c ath10k: enable QCA6174 hw3.2 SDIO hardware
After implementing PN replay check we can enable SDIO support on QCA6174.
Tested with client mode on all security modes, and fragmentation as well. AP
mode does not work yet.

Also tone down the warning about SDIO being not ready yet.

Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1. AP mode
is not working yet.

Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-29 17:37:54 +03:00
Wen Gong
33f9747291 ath10k: add fragmentation handler for high latency devices
On high latency devices (SDIO, USB) ath10k did not handle fragmented frames and
all fragmented frames on receive path were lost in ath10k. Even a simple ping
test failed with fragmentation.

The fragmented packets are decapsulated based on the security mode, then the PN
is checked and the fragmented frame is passed to mac80211.  mac80211 in
ieee80211_rx_h_defragment() will then combine the fragment frames and forward
to upper layers.

Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.

Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-29 17:37:44 +03:00
Wen Gong
130c774957 ath10k: add PN replay protection for high latency devices
On high latency devices (SDIO, USB) ath10k did not do PN replay check, a data
frame with an invalid PN number was not discard as it should have been. So this
patch implements PN replay in ath10k. PN replay check for fragmented frames is
implemented in followup patch.

With low latency devices (PCI, AHB) hardware can store the data
frames's content to host memory directly and the firmware can fully reorder
data frames, and do PN replay check at the same time. But for high latency
devices all data frames will be received and stored in firmware's memory and it
is hard to do full reorder because of the memory size limitations in the
firmware. This is why the PN replay protections needs to be implemented in host
driver.

Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.

Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-29 17:37:34 +03:00
Wen Gong
28ce53b6cf ath10k: add handler for HTT_T2H_MSG_TYPE_SEC_IND event
Add the handler for HTT_T2H_MSG_TYPE_SEC_IND event from firmware, which stores
PN for replay check implemented in the following patch.

Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.

Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-29 17:37:23 +03:00
Wen Gong
e1bddde973 ath10k: add struct for high latency PN replay protection
Add the struct for PN replay protection and fragment packet
handler.

Also fix the bitmask of HTT_RX_DESC_HL_INFO_MCAST_BCAST to match what's currently
used by SDIO firmware. The defines are not used yet so it's safe to modify
them. Remove the conflicting HTT_RX_DESC_HL_INFO_FRAGMENT as
it's not either used in ath10k.

Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.

Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-29 17:37:13 +03:00
Paul Walmsley
45c054d081 tty: serial: add driver for the SiFive UART
Add a serial driver for the SiFive UART, found on SiFive FU540 devices
(among others).

The underlying serial IP block is relatively basic, and currently does
not support serial break detection.  Further information on the IP
block can be found in the documentation and Chisel sources:

    https://static.dev.sifive.com/FU540-C000-v1.0.pdf

    https://github.com/sifive/sifive-blocks/tree/master/src/main/scala/devices/uart

This driver was written in collaboration with Wesley Terpstra
<wesley@sifive.com>.

Tested on a SiFive HiFive Unleashed A00 board, using BBL and the open-
source FSBL (using a DT file based on what's targeted for mainline).

This revision incorporates changes based on comments by Julia Lawall
<julia.lawall@lip6.fr>, Emil Renner Berthing <kernel@esmil.dk>, and
Andreas Schwab <schwab@suse.de>.  Thanks also to Andreas for testing
the driver with his userspace and reporting a bug with the
set_termios implementation.

Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Wesley Terpstra <wesley@sifive.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Emil Renner Berthing <kernel@esmil.dk>
Cc: Andreas Schwab <schwab@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-29 16:30:59 +02:00
Paul Walmsley
e5c8fe558c dt-bindings: serial: add documentation for the SiFive UART driver
Add DT binding documentation for the Linux driver for the SiFive
asynchronous serial IP block.

This revision incorporates changes based on feedback from Rob
Herring <robh@kernel.org>.

Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: linux-serial@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-29 16:30:59 +02:00
Boyang Zhou
f08cae2f28 arm64: mmap: Ensure file offset is treated as unsigned
The file offset argument to the arm64 sys_mmap() implementation is
scaled from bytes to pages by shifting right by PAGE_SHIFT.
Unfortunately, the offset is passed in as a signed 'off_t' type and
therefore large offsets (i.e. with the top bit set) are incorrectly
sign-extended by the shift. This has been observed to cause false mmap()
failures when mapping GPU doorbells on an arm64 server part.

Change the type of the file offset argument to sys_mmap() from 'off_t'
to 'unsigned long' so that the shifting scales the value as expected.

Cc: <stable@vger.kernel.org>
Signed-off-by: Boyang Zhou <zhouby_cn@126.com>
[will: rewrote commit message]
Signed-off-by: Will Deacon <will.deacon@arm.com>
2019-04-29 15:27:41 +01:00
Rafael J. Wysocki
9e80ad37f6 ath10k: Drop WARN_ON()s that always trigger during system resume
ath10k_mac_vif_chan() always returns an error for the given vif
during system-wide resume which reliably triggers two WARN_ON()s
in ath10k_bss_info_changed() and they are not particularly
useful in that code path, so drop them.

Tested: QCA6174 hw3.2 PCI with WLAN.RM.2.0-00180-QCARMSWPZ-1
Tested: QCA6174 hw3.2 SDIO with WLAN.RMH.4.4.1-00007-QCARMSWP-1

Fixes: cd93b83ad9 ("ath10k: support for multicast rate control")
Fixes: f279294e9e ("ath10k: add support for configuring management packet rate")
Cc: stable@vger.kernel.org
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Tested-by: Claire Chang <tientzu@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-29 17:26:14 +03:00
Brian Norris
38faed1504 ath10k: perform crash dump collection in workqueue
Commit 25733c4e67 ("ath10k: pci: use mutex for diagnostic window CE
polling") introduced a regression where we try to sleep (grab a mutex)
in an atomic context:

[  233.602619] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:254
[  233.602626] in_atomic(): 1, irqs_disabled(): 0, pid: 0, name: swapper/0
[  233.602636] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G        W         5.1.0-rc2 #4
[  233.602642] Hardware name: Google Scarlet (DT)
[  233.602647] Call trace:
[  233.602663]  dump_backtrace+0x0/0x11c
[  233.602672]  show_stack+0x20/0x28
[  233.602681]  dump_stack+0x98/0xbc
[  233.602690]  ___might_sleep+0x154/0x16c
[  233.602696]  __might_sleep+0x78/0x88
[  233.602704]  mutex_lock+0x2c/0x5c
[  233.602717]  ath10k_pci_diag_read_mem+0x68/0x21c [ath10k_pci]
[  233.602725]  ath10k_pci_diag_read32+0x48/0x74 [ath10k_pci]
[  233.602733]  ath10k_pci_dump_registers+0x5c/0x16c [ath10k_pci]
[  233.602741]  ath10k_pci_fw_crashed_dump+0xb8/0x548 [ath10k_pci]
[  233.602749]  ath10k_pci_napi_poll+0x60/0x128 [ath10k_pci]
[  233.602757]  net_rx_action+0x140/0x388
[  233.602766]  __do_softirq+0x1b0/0x35c
[...]

ath10k_pci_fw_crashed_dump() is called from NAPI contexts, and firmware
memory dumps are retrieved using the diag memory interface.

A simple reproduction case is to run this on QCA6174A /
WLAN.RM.4.4.1-00132-QCARMSWP-1, which happens to be a way to b0rk the
firmware:

  dd if=/sys/kernel/debug/ieee80211/phy0/ath10k/mem_value bs=4K count=1
of=/dev/null

(NB: simulated firmware crashes, via debugfs, don't trigger firmware
dumps.)

The fix is to move the crash-dump into a workqueue context, and avoid
relying on 'data_lock' for most mutual exclusion. We only keep using it
here for protecting 'fw_crash_counter', while the rest of the coredump
buffers are protected by a new 'dump_mutex'.

I've tested the above with simulated firmware crashes (debugfs 'reset'
file), real firmware crashes (the 'dd' command above), and a variety of
reboot and suspend/resume configurations on QCA6174A.

Reported here:
http://lkml.kernel.org/linux-wireless/20190325202706.GA68720@google.com

Fixes: 25733c4e67 ("ath10k: pci: use mutex for diagnostic window CE polling")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-29 17:24:37 +03:00
Shubhrajyoti Datta
1863178b20 serial: uartps: Add support for cts-override
Having flow is configurable. Add support for the same by
checking for cts-override.

Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-29 16:20:24 +02:00
Shubhrajyoti Datta
b1072b4f6e dt-bindings: xilinx-uartps: Add support for cts-override
Flow control is configurable in xilinx-uartps
Add a dt binding to check for the same.

Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-29 16:20:24 +02:00
Wei Yongjun
74cdf8cec7 serial: milbeaut_usio: Fix error handling in probe and remove
devm_clk_get() is used so there is no reason to explicitly call
clk_put() in probe or remove functions. Also remove duplicate assign
for port->membase.

Fixes: ba44dc0430 ("serial: Add Milbeaut serial control")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Tested-by: Sugaya Taichi <sugaya.taichi@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-29 16:20:24 +02:00
Johan Hovold
0f02321e4b USB: cdc-acm: clean up throttle handling
Clean up the throttle implementation by dropping the redundant
throttle_req flag which was a remnant from back when USB serial had only
a single read URB, something which was later carried over to cdc-acm.

Also convert the throttled flag to an atomic bit flag.

Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-29 16:14:41 +02:00
Johan Hovold
764478f411 USB: cdc-acm: fix unthrottle races
Fix two long-standing bugs which could potentially lead to memory
corruption or leave the port throttled until it is reopened (on weakly
ordered systems), respectively, when read-URB completion races with
unthrottle().

First, the URB must not be marked as free before processing is complete
to prevent it from being submitted by unthrottle() on another CPU.

	CPU 1				CPU 2
	================		================
	complete()			unthrottle()
	  process_urb();
	  smp_mb__before_atomic();
	  set_bit(i, free);		  if (test_and_clear_bit(i, free))
						  submit_urb();

Second, the URB must be marked as free before checking the throttled
flag to prevent unthrottle() on another CPU from failing to observe that
the URB needs to be submitted if complete() sees that the throttled flag
is set.

	CPU 1				CPU 2
	================		================
	complete()			unthrottle()
	  set_bit(i, free);		  throttled = 0;
	  smp_mb__after_atomic();	  smp_mb();
	  if (throttled)		  if (test_and_clear_bit(i, free))
		  return;			  submit_urb();

Note that test_and_clear_bit() only implies barriers when the test is
successful. To handle the case where the URB is still in use an explicit
barrier needs to be added to unthrottle() for the second race condition.

Also note that the first race was fixed by 36e59e0d70 ("cdc-acm: fix
race between callback and unthrottle") back in 2015, but the bug was
reintroduced a year later.

Fixes: 1aba579f3c ("cdc-acm: handle read pipe errors")
Fixes: 088c64f812 ("USB: cdc-acm: re-write read processing")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-29 16:14:41 +02:00
zhengbin
d671002be6 locking/lockdep: Remove unnecessary unlikely()
DEBUG_LOCKS_WARN_ON() already contains an unlikely(), there is no need
for another one.

Signed-off-by: zhengbin <zhengbin13@huawei.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: houtao1@huawei.com
Link: http://lkml.kernel.org/r/1556540791-23110-1-git-send-email-zhengbin13@huawei.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2019-04-29 16:11:01 +02:00
Ingo Molnar
46938cc8ab x86/paravirt: Rename paravirt_patch_site::instrtype to paravirt_patch_site::type
It's used as 'type' in almost every paravirt patching function, so standardize
the field name from the somewhat weird 'instrtype' name to 'type'.

Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@surriel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2019-04-29 16:05:54 +02:00
Ingo Molnar
1fc654cf6e x86/paravirt: Standardize 'insn_buff' variable names
We currently have 6 (!) separate naming variants to name temporary instruction
buffers that are used for code patching:

 - insnbuf
 - insnbuff
 - insn_buff
 - insn_buffer
 - ibuf
 - ibuffer

These are used as local variables, percpu fields and function parameters.

Standardize all the names to a single variant: 'insn_buff'.

Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@surriel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2019-04-29 16:05:49 +02:00
Florian Fainelli
082ce27ff4 irqchip/bcm: Restore registration print with %pOF
It is useful to print which interrupt controllers are registered in the
system and which parent IRQ they use, especially given that L2 interrupt
controllers do not call request_irq() on their parent interrupt and do
not appear under /proc/interrupts for that reason.

We used to print the base register address virtual address which had
little value, use %pOF to print the path to the Device Tree node which
maps to the physical address more easily and is what people need to
troubleshoot systems.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2019-04-29 15:00:02 +01:00
Sven Van Asbroeck
f22b1ba15e rtc: 88pm860x: prevent use-after-free on device remove
The device's remove() attempts to shut down the delayed_work scheduled
on the kernel-global workqueue by calling flush_scheduled_work().

Unfortunately, flush_scheduled_work() does not prevent the delayed_work
from re-scheduling itself. The delayed_work might run after the device
has been removed, and touch the already de-allocated info structure.
This is a potential use-after-free.

Fix by calling cancel_delayed_work_sync() during remove(): this ensures
that the delayed work is properly cancelled, is no longer running, and
is not able to re-schedule itself.

This issue was detected with the help of Coccinelle.

Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2019-04-29 15:53:43 +02:00
Kefeng Wang
527bd754d1 rtc: Use dev_get_drvdata()
Using dev_get_drvdata directly.

Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: linux-rtc@vger.kernel.org
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2019-04-29 15:53:43 +02:00
Alexandre Belloni
c8889bb6e6 rtc: imxdi: convert to SPDX identifier
Use SPDX-License-Identifier instead of a verbose license text.

Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2019-04-29 15:53:43 +02:00
Alexandre Belloni
629d488a3e rtc: imxdi: remove unnecessary check
The RTC core already ensures the alarm is set to a time in the future, it
is not necessary to check again in the driver.

Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2019-04-29 15:53:43 +02:00
Alexandre Belloni
d231d32caa rtc: imxdi: use .set_time
Use .set_time instead of the deprecated .set_mmss.

Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2019-04-29 15:53:43 +02:00
Alexandre Belloni
93059793ad rtc: imxdi: switch to rtc_time64_to_tm/rtc_tm_to_time64
Call the 64bit versions of rtc_tm time conversion now that the range is
enforced by the core.

Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2019-04-29 15:53:43 +02:00
Alexandre Belloni
21c9dfda4b rtc: imxdi: set range
The RTC Time Counter MSB Register contains the 32 most significant bits
(47:16) of the 47-bit RTC Time Counter. Clocked by a 32.768 KHz clock, this
register is effectively a 32-bit seconds counter.

Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2019-04-29 15:53:43 +02:00
Alexandre Belloni
02bc723579 rtc: mxc: use .set_time
Use .set_time instead of the deprecated .set_mmss64.

Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2019-04-29 15:53:43 +02:00
Alexandre Belloni
83888df4b8 rtc: mxc: set range
Let the core handle the range, and in particular the imx1 offsetting. This
has the benefit of extending the range of the RTC further than 365 days and
making .read_time useful again on imx1.

Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2019-04-29 15:53:42 +02:00
Alexandre Belloni
ebc2ec4ecf rtc: mxc: fix possible race condition
The IRQ is requested before the struct rtc is allocated and registered, but
this struct is used in the IRQ handler. This may lead to a NULL pointer
dereference.

Switch to devm_rtc_allocate_device/rtc_register_device to allocate the rtc
struct before requesting the IRQ.

Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2019-04-29 15:53:42 +02:00
Fabien Dessenne
cf612c5949 rtc: stm32: manage the get_irq probe defer case
Manage the -EPROBE_DEFER error case for the wake IRQ.

Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Acked-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2019-04-29 15:53:42 +02:00