The call to of_get_child_by_name returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/pinctrl/pinctrl-pistachio.c:1422:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1360, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
H6 SoC has a "pio group withstand voltage mode" register (datasheet
description), that needs to be used to select either 1.8V or 3.3V I/O mode,
based on what voltage is powering the respective pin banks and is thus used
for I/O signals.
Add support for configuring this register according to the voltage of the
pin bank regulator (if enabled).
This is similar to the support for I/O bias voltage setting patch for A80
and the same concerns apply. See:
commit 402bfb3c13 ("Support I/O bias voltage setting on A80")
Signed-off-by: Ondrej Jirman <megous@megous.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
H6 has a different I/O voltage bias setting method than A80. Prepare
existing code for using alternative bias voltage setting methods.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is mostly a revert of commit 55bb6a633c ("clk: rockchip: mark
noc and some special clk as critical on rk3288") except that we're
keeping "pmu_hclk_otg0" as critical still.
NOTE: turning these clocks off doesn't seem to do a whole lot in terms
of power savings (checking the power on the logic rail). It appears
to save maybe 1-2mW. ...but still it seems like we should turn the
clocks off if they aren't needed.
About "pmu_hclk_otg0" (the one clock from the original commit we're
still keeping critical) from an email thread:
> pmu ahb clock
>
> Function: Clock to pmu module when hibernation and/or ADP is
> enabled. Must be greater than or equal to 30 MHz.
>
> If the SOC design does not support hibernation/ADP function, only have
> hclk_otg, this clk can be switched according to the usage of otg.
> If the SOC design support hibernation/ADP, has two clocks, hclk_otg and
> pmu_hclk_otg0.
> Hclk_otg belongs to the closed part of otg logic, which can be switched
> according to the use of otg.
>
> pmu_hclk_otg0 belongs to the always on part.
>
> As for whether pmu_hclk_otg0 can be turned off when otg is not in use,
> we have not tested. IC suggest make pmu_hclk_otg0 always on.
For the rest of the clocks:
atclk: No documentation about this clock other than that it goes to
the CPU. CPU functions fine without it on. Maybe needed for JTAG?
jtag: Presumably this clock is only needed if you're debugging with
JTAG. It doesn't seem like it makes sense to waste power for every
rk3288 user. In any case to do JTAG you'd need private patches to
adjust the pinctrl the mux the JTAG out anyway.
pclk_dbg, pclk_core_niu: On veyron Chromebooks we turn these two
clocks on only during kernel panics in order to access some coresight
registers. Since nothing in the upstream kernel does this we should
be able to leave them off safely. Maybe also needed for JTAG?
hsicphy12m_xin12m: There is no indication of why this clock would need
to be turned on for boards that don't use HSIC.
pclk_ddrupctl[0-1], pclk_publ0[0-1]: On veyron Chromebooks we turn
these 4 clocks on only when doing DDR transitions and they are off
otherwise. I see no reason why they'd need to be on in the upstream
kernel which doesn't support DDRFreq.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
In the event that the start address of the initrd is not aligned, but
has an aligned size, the base + size will not cover the entire initrd
image and there is a chance that the kernel will corrupt the tail of the
image.
By aligning the end of the initrd to a page boundary and then
subtracting the adjusted start address the memblock reservation will
cover all pages that contains the initrd.
Fixes: c756c592e4 ("arm64: Utilize phys_initrd_start/phys_initrd_size")
Cc: stable@vger.kernel.org
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When building CONFIG_ACPI is not set
gcc warn this:
drivers/gpio/gpio-merrifield.c: In function mrfld_gpio_get_pinctrl_dev_name:
drivers/gpio/gpio-merrifield.c:388:19: error: dereferencing pointer to incomplete type struct acpi_device
put_device(&adev->dev);
^~
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: d00d2109c3 ("gpio: merrifield: Convert to use acpi_dev_get_first_match_dev()")
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The call to of_get_child_by_name returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/pinctrl/pinctrl-st.c:1188:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1175, but without a corresponding object release within this function.
./drivers/pinctrl/pinctrl-st.c:1188:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1175, but without a corresponding object release within this function.
./drivers/pinctrl/pinctrl-st.c:1199:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1175, but without a corresponding object release within this function.
./drivers/pinctrl/pinctrl-st.c:1199:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1175, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org (open list)
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The call to of_find_compatible_node returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/pinctrl/samsung/pinctrl-exynos-arm.c:76:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 66, but without a corresponding object release within this function.
./drivers/pinctrl/samsung/pinctrl-exynos-arm.c:82:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 66, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currenly, __cpufreq_get() called by show_cpuinfo_cur_freq() will check
->get callback. That is needless since cpuinfo_cur_freq attribute will
not be created if ->get is not set. So let's drop it in __cpufreq_get().
Also keep this check in cpufreq_get().
Signed-off-by: Yue Hu <huyue2@yulong.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Skip conversion to platform_device and use dev_get_drvdata() directly.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
For now, we don't take into account the pin bias settings supplied by ACPI.
This change is targeting the mentioned gap.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This helper consolidates all settings of GPIO descriptor lookup flags and
quirks in the future if any.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ACPI GpioIo() resource may have different bias settings.
For now, we distinguish only PullUp() setting in order to configure
the initial state of a pin.
Take into consideration the rest of the possible choices as well,
i.e. PullDown, PullNone and PullDefault, when configuring the initial state
of the pin.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Most of the code inside GPIO library is using enum gpiod_flags.
Some of the function still operate with unsigned int.
In order to be more consistent and better type checking, convert
acpi_gpiochip_parse_own_gpio() to use enum gpiod_flags instead of
unsigned int.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since GPIO library operates with enumerator when it's subject to handle
the GPIO lookup flags, it will be better to clearly see what default means.
Thus, introduce GPIO_LOOKUP_FLAGS_DEFAULT entry to describe
the default assumptions.
While here, replace 0 by newly introduced constant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The library uses enum gpio_lookup_flags to define the possible
characteristics of GPIO pin. Since enumerator listed only individual
bits the common use of it is in a form of a bitmask of
gpio_lookup_flags GPIO_* values. The more correct type for this is
unsigned long.
Due to above convert all users to use unsigned long instead of
enum gpio_lookup_flags except enumerator definition.
While here, make field and parameter descriptions consistent as well.
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Indent entry values in the enum gpio_lookup_flags for better readability.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The strcpy() function is being deprecated. Replace it by the safer
strscpy() and fix the following Coverity warnings:
"You might overrun the 15-character fixed-size string event->bus_id
by copying bus_id without checking the length."
"You might overrun the 20-character fixed-size string event->device_class
by copying device_class without checking the length."
Addresses-Coverity-ID: 139001 ("Copy into fixed size buffer")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Align pins names with names provided in official stm32mp157 datasheet
available on st.com.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A same SoC can be available in several packages. Differences between
packages are only the numbers of available balls. In order not to write
a driver for each new package, same driver (ex: pinctrl-stm32mp157.c) will
be used. This patch introduces the "package" property for each pin. So on a
same driver, it will be possible to indicate on which package the pin is
available. The package information will be got from the device tree.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
sync_dump() is an unused, unexported, function that adds 64k to the
kernel image and doesn't even provide locking around the global array it
uses.
add/remove: 0/2 grow/shrink: 0/0 up/down: 0/-65734 (-65734)
Function old new delta
sync_dump 198 - -198
sync_dump_buf 65536 - -65536
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190419181904.6199-1-chris@chris-wilson.co.uk
Fix the order of lane, port parameters passed to the register macro.
Note that this was already partly fixed by commit
37fc7845df ("drm/i915: Call MG_DP_MODE() macro with the right parameters order")
While at it simplify things by using the macro directly instead of an
unnecessary redirection via an array.
v2:
- Add a note the commit message about simplifying things. (José)
Fixes: 58106b7d81 ("drm/i915: Make MG PHY macros semantically consistent")
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Aditya Swarup <aditya.swarup@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190419071026.32370-1-imre.deak@intel.com
A per vcpu flag is added to check if pointer authentication is
enabled for the vcpu or not. This flag may be enabled according to
the necessary user policies and host capabilities.
This patch also adds a helper to check the flag.
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <christoffer.dall@arm.com>
Cc: kvmarm@lists.cs.columbia.edu
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
None of them have any external callers, make them static.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
No external dependencies, might as well handle this directly.
xfrm_afinfo_policy is now 40 bytes on x86_64.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
handle this directly, its only used by ipv6.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Only used by ipv4, we can read the fl4 tos value directly instead.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
All we do is write the length/status and address bits to a DMA
descriptor only to write its contents into on-chip registers right
after, eliminate this unnecessary step.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx_status poll in the rcar_dmac driver reads the status register
which indicates which chunk is busy (DMACHCRB). Afterwards the point
inside the chunk is read from DMATCRB. It is possible that the chunk
has changed between the two reads. The result is a non-monotonous
increase of the residue. Fix this by introducing a 'safe read' logic.
Fixes: 73a47bd0da ("dmaengine: rcar-dmac: use TCRB instead of TCR for residue")
Signed-off-by: Achim Dahlhoff <Achim.Dahlhoff@de.bosch.com>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: <stable@vger.kernel.org> # v4.16+
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Having a cyclic DMA, a residue 0 is not an indication of a completed
DMA. In case of cyclic DMA make sure that dma_set_residue() is called
and with this a residue of 0 is forwarded correctly to the caller.
Fixes: 3544d28788 ("dmaengine: rcar-dmac: use result of updated get_residue in tx_status")
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Achim Dahlhoff <Achim.Dahlhoff@de.bosch.com>
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Yao Lihua <ylhuajnu@outlook.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Without this patch the socket address family sporadically gets wrong
value ends up the dev_set_mac_address() fails to set the desired MAC
address.
Fixes: 25766271e4 ("r8152: Refresh MAC address during USBDEVFS_RESET")
Signed-off-by: Crag.Wang <crag.wang@dell.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-By: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit af19b7ce76 ("mmc: bcm2835: Avoid possible races on
data requests") introduces a possible circular locking dependency,
which is triggered by swapping to the sdhost interface.
So instead of reintroduce the race condition again, we could also
avoid this situation by using GFP_NOWAIT for the allocation of the
DMA buffer descriptors.
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: af19b7ce76 ("mmc: bcm2835: Avoid possible races on data requests")
Link: http://lists.infradead.org/pipermail/linux-rpi-kernel/2019-March/008615.html
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add the Audio DSP (ADSP) and Compute DSP (CDSP) nodes for TrustZone
based remoteproc, supporting booting these cores on e.g. the MTP, and
enable the same for the MTP.
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Define the rmtfs memory node. As the memory region specified in version
10 of the memory map is only 1MB a chunk of unallocated memory is
chosen.
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Update existing and add missing regions to the reserved memory map, as
described in version 10.
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Wire up the reset controller in the Qcom UFS controller for the PHY.
This will be used to toggle PHY reset during initialization of the PHY.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Ido Schimmel says:
====================
mlxsw: Shared buffer improvements
This patchset includes two improvements with regards to shared buffer
configuration in mlxsw.
The first part of this patchset forbids the user from performing illegal
shared buffer configuration that can result in unnecessary packet loss.
In order to better communicate these configuration failures to the user,
extack is propagated from devlink towards drivers. This is done in
patches #1-#8.
The second part of the patchset deals with the shared buffer
configuration of the CPU port. When a packet is trapped by the device,
it is sent across the PCI bus to the attached host CPU. From the
device's perspective, it is as if the packet is transmitted through the
CPU port.
While testing traffic directed at the CPU it became apparent that for
certain packet sizes and certain burst sizes, the current shared buffer
configuration of the CPU port is inadequate and results in packet drops.
The configuration is adjusted by patches #9-#14 that create two new pools
- ingress & egress - which are dedicated for CPU traffic.
====================
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch the CPU port to use the new dedicated egress pool instead the
previously used egress pool which was shared with normal front panel
ports.
Add per-port quotas for the amount of traffic that can be buffered for
the CPU port and also adjust the per-{port, TC} quotas.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPU port is used to transmit traffic that is trapped to the host
CPU. It is therefore irrelevant to define ingress quota for it.
Add a 'skip_ingress' argument to the function tasked with configuring
per-port quotas, so that ingress quotas could be skipped in case the
passed local port is the CPU port.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function is used to set the per-port shared buffer quotas.
Currently, these quotas are only set for front panel ports, but a
subsequent patch will configure these quotas for the CPU port as well.
The configuration required for the CPU port is a bit different than that
of the front panel ports, so split the business logic into a separate
function which will be called with different parameters for the CPU
port.
No functional changes intended.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new ingress pool that was added in the previous patch for
control packets (e.g., STP, LACP) that are trapped to the CPU.
The previous management pool is no longer necessary and therefore its
size is set to 0.
The maximum quota for traffic towards the CPU is increased to 50% of the
free space in the new ingress pool and therefore the reserved space is
reduced by half, to 10KB - in both the shared and headroom buffer. This
allows for more efficient utilization of the shared buffer as reserved
space cannot be used for other purposes.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets that are trapped to the CPU are transmitted through the CPU port
to the attached host. The CPU port is therefore like any other port and
needs to have shared buffer configuration.
The maximum quotas configured for the CPU are provided using dynamic
threshold and cannot be changed by the user. In order to make sure that
these thresholds are always valid, the configuration of the threshold
type of these pools is forbidden.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code currently assumes that ingress pools have lower indices than
egress pools. This makes it impossible to add more ingress pools
without breaking user configuration that relies on a certain pool index
to correspond to an egress pool.
Remove such assumptions from the code, so that more ingress pools could
be added by subsequent patches.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e83c045e53 ("mlxsw: spectrum_buffers: Configure MC pool")
configured the threshold of the multicast TCs as infinite so that the
admission of multicast packets is only depended on per-switch priority
threshold.
Forbid the user from changing the thresholds of these multicast TCs and
their binding to a different pool.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multicast packets have three egress quotas:
* Per egress port
* Per egress port and traffic class
* Per switch priority
The limits on the switch priority are not exposed to the user and
specified as dynamic threshold on the first egress pool.
Forbid changing the threshold type of the first egress pool so that
these limits are always valid.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e83c045e53 ("mlxsw: spectrum_buffers: Configure MC pool") added
a dedicated pool for multicast traffic. The pool is visible to the user
so that it would be possible to monitor its occupancy, but its
configuration should be forbidden in order to maintain its intended
operation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>