Commit graph

982,081 commits

Author SHA1 Message Date
James Smart
9a66d990c7 scsi: lpfc: Add loopback testing to trunking mode
When in trunking mode, the adapter can be placed into diagnostic mode and
each link in the trunk tested via loopback.

Add support to the driver to perform per-link loopback testing when in
trunking mode.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 13:15:09 -04:00
James Smart
f3339800f9 scsi: lpfc: Fix link speed reporting for 4-link trunk
Driver is using uint16_t and is encountering an overflow of the 16bits when
calculating link speed.

Fix by using a u32 type.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 13:15:09 -04:00
James Smart
19193ff34e scsi: lpfc: Fix handling of trunk links state reporting
If all the trunk links drop and a single link resumes, the link_state is
not properly reported. When trunked, the driver receives two async
cqes. One acqe reports the trunk link states, which the driver records.
The other cqe reports the overall state of the trunk. In the failing case,
the trunk link state acqe preceeds the overall trunk link state acqe. The
trunk link state acqe, as it's an "up" transition, calls a code path which
ensures a down transition before moving to the up state.  The down
transition had a side effect of clearing the just-saved trunk link states.

Fix by not clearing the trunk link states if we've already transitioned
to a down state.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 13:15:09 -04:00
James Smart
e4771ec3c8 scsi: lpfc: Fix protocol support on G6 and G7 adapters
Invalid test is allowing Loop to be a supported topology on G6 and G7
adapters. The chips do not support loop as their link speeds prohibit loop
per standard.

Correct the conditional so that loop is not reported.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 13:15:09 -04:00
James Smart
b3b4f3e1d5 scsi: lpfc: Correct boot bios information to FDMI registration
The driver is currently reporting the firmware revision not the actual boot
bios version in FDMI data.

Modify the driver to obtain the boot bios version from the adapter and use
that data in the FMDI data sent to the switch.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 13:15:09 -04:00
James Smart
f4f87861d9 scsi: lpfc: Fix HDMI2 registration string for symbolic name
The switch is rejecting FDMI2 registration for symbolic name.  There is a
"\n" in the name string, which the switch dislikes thus rejects the
registration.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 13:15:09 -04:00
James Smart
32a80c093b scsi: lpfc: Fix fc4type information for FDMI
The driver is reporting support for NVME even when not configured for NVME
operation.

Fix (and make more readable) when NVME protocol support is indicated.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 13:15:09 -04:00
James Smart
d67f935b79 scsi: lpfc: Fix FDMI manufacturer attribute value
The FDMI manufacturer value being reported on Linux is inconsistent with
other OS's.

Set the value to "Emulex Corporation" for consistency.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 13:15:09 -04:00
James Smart
c66a919746 scsi: lpfc: Fix io lost on host resets
If the driver undergoes repeated host resets it starts losing exchange
structures and eventually returns SCSI_MLQUEUE_HOST_BUSY and does not
recover. The offline path is not reclaiming the outstanding ios on the fcp
pring txcmplq before calling lpfc_destroy_multixripool, which causes the
txmcplq to be reinit and the resources lost.

Flush the fcp rings before destroying the multixripools.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 13:15:09 -04:00
James Smart
e8869f5b0a scsi: lpfc: Fix mailbox hang on adapter init
The adapter initialization sequence enables interrupts, initializes the
adapter link_state to LINK_DOWN, then issues commands to initialize the
adapter. The interrupt handler on the adapter validates the link_state (has
to be at least LINK_DOWN) and if invalid, will discard the interrupting
event.

In most cases, there is not a command completion, thus an interrupt until
the initialization commands have been sent which is post the setting of
state to LINK_DOWN.  However, in cases of firmware reset, the reset will
modify the link_state to an invalid value (indicating a reset of the
adapter) and there occasionally are cases where the adapter will generate
an asynchronous event which shares the eq/cq used for mailbox commands. In
the failure case, an interrupt is generated immediately after enabling them
due to the async event.  As link_state is invalid, the eq is list and the
CQ not serviced.  At this point link_state is initialized and the mailbox
command sent.  As the CQ has not been serviced, it is not armed, so no
interrupt event is generated when the mailbox command completes.

Modify the initialization sequence so that interrupts are enabled after
link_state is properly initialized, which avoids the race condition with
the async event.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 13:15:08 -04:00
James Smart
bbd3d7380b scsi: lpfc: Fix driver crash in target reset handler
It's possible for the scsi error handler to fire and call the target reset
handler simultaneously to the driver logging out and relogging into the
system.  If hit just right, the re-login may not have fully re-established
the remote port and the rdata->pnod structure may be null.

Check for NULL in the reset handler and return failure if NULL.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 13:15:08 -04:00
James Smart
2a0fb340fc scsi: lpfc: Correct localport timeout duration error
Current code incorrectly specifies a completion wait timeout duration in 5
jiffies, when it should have been 5 seconds.

Fix the adjust for units for the completion timeout call.

[mkp: manual merge]

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 13:15:08 -04:00
James Smart
e2ffe4d5dc scsi: lpfc: Convert bootstrap mbx polling from msleep to udelay
Current code is using msleep when polling for hw ready. Unfortunately the
msleep routine isn't very accurate on rescheduling. In fact, on a busy
systems which reset the adapter, it became 10s of seconds before it was
rescheduled.

Fix by busy waiting using udelay. As we're now busy waiting, significantly
reduce the wait time so that we can exit the pool loop as soon as possible.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 12:57:02 -04:00
James Smart
4645f7b56a scsi: lpfc: Coordinate adapter error handling with offline handling
The driver periodically checks for adapter error in a background thread. If
the thread detects an error, the adapter will be reset including the
deletion and reallocation of workqueues on the adapter.  Simultaneously,
there may be a user-space request to offline the adapter which may try to
do many of the same steps, in parallel, on a different thread. As memory
was deallocated while unexpected, the parallel offline request hit a bad
pointer.

Add coordination between the two threads.  The error recovery thread has
precedence. So, when an error is detected, a flag is set on the adapter to
indicate the error thread is terminating the adapter. But, before doing
that work, it will look for a flag that is set by the offline flow, and if
set, will wait for it to complete before then processing the error handling
path.  Similarly, in the offline thread, it first checks for whether the
error thread is resetting the adapter, and if so, will then wait for the
error thread to finish. Only after it has finished, will it set its flag
and offline the adapter.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 12:57:02 -04:00
James Smart
32a9310076 scsi: lpfc: Stop adapter if pci errors detected
In a couple of cases, the driver detected a pci error (via pci device state
or via failed register reads) but didn't take any action to disable the
device.  Additionally, the driver is ignoring the status of pci
configuration space reads.

Having the driver take the adapter offline whenever the pci error is
detected.  Pay attention to pci_config_space_read status and return failure
if an error is seen.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 12:57:02 -04:00
James Smart
731eedcb31 scsi: lpfc: Fix deadlock due to nested hbalock call
If an adapter fails, causing a board reset, the board reset routine
lpfc_hba_down_s4() takes the hbalock out then calls
lpfc_nvmet_ctxbuf_post() who then tries to take out the same lock.  As the
context lists are now protected under the buf_list_locks, there is no need
for the hbalock to be held by the board reset routine.

Fix by no longer taking the hbalock in the board reset routine.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 12:57:02 -04:00
James Smart
22b738ac33 scsi: lpfc: Fix nvmet handling of first burst cmd
With negative test injection, the driver is receiving a command with first
burst enabled, meaning Sequence initiative is not passed with the command
frame. The driver notes the condition and discards the frame.  However the
driver calls the incorrect buffer free routine, resulting in a NULL pointer
reference.

For hbq buffer free, convert to using lpfc_rq_buf_free().

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 12:57:02 -04:00
James Smart
982ab128dc scsi: lpfc: Fix lpfc_nvmet_mrq attribute handling when 0
Currently, when lpfc_nvmet_mrq is 0 it could mean 2 different things
depending on when its looked at. If at module load time it specifies the
default number of hardware queues to allocate, with 0 meaning default to
the number of CPUs. But post module load, a value of zero means to disable
mrq use.

Changed the driver so that enablement of mrq is based on whether nvme
target mode is enabled or not. When enabled, mrq is enabled.  Thus, the
cfg_nvemt_mrq field only specifies the number of mrq queues to enable, with
0 defaulting to the number of cpus.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 12:57:02 -04:00
James Smart
4552e0f6fa scsi: lpfc: Fix nvmet async receive buffer replenishment
Under circustances with high load, the driver is running out of async
receive buffers which may result in one of the following messages:

0:6401 RQE Error x13, posted 226 err_cnt 0: 925c6050 925c604e 925c5d54

or

0:2885 Port Status Event: port status reg 0x81800000,
       port smphr reg 0xc000, error 1=0x52004a01, error 2=0x0

The driver is waiting for full io completion before returning receive
buffers to the adapter. There is no need for such a relationship.

Whenever a new command is received from the wire, the driver will have two
contexts - an io context (ctxp) and a receive buffer context.  In current
code, the receive buffer context stays 1:1 with the io and won't be
reposted to the hardware until the io completes. There is no need for such
a relationship.

Change the driver so that up on successful handing of the command to the
transport, where the transport has copied what it needed thus the buffer is
returned to the driver, have the driver immediately repost the buffer to
the hardware. If the command cannot be successfully handed to the transport
as transport resources are temporarily busy, have the driver allocate a new
and separate receive buffer and post it to the hardware so that hardware
can continue while the command is queued for the transport.

When an io is complete, the transport returns the io context to the driver,
and the driver may be waiting for more contexts, thus immediately reuse the
io context. In this path, there was a buffer posted when the receive buffer
was queued waiting for an io context so a replacement is not needed in the
new code additions. Thus, exempt this the context reuse case from the
buffer reposting.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 12:57:02 -04:00
James Smart
def11a58c1 scsi: lpfc: Fix location of SCSI ktime counters
The debug ktime counters that trace an io were inadvertently not placed in
the common section of an io buffer. Thus, they generate an invalid opcode
error when accessed.

Move the ktime counters into the common area.

Fixes: 0794d601d1 ("scsi: lpfc: Implement common IO buffers between NVME and SCSI")
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 12:57:02 -04:00
James Smart
c95a3b4b0f scsi: lpfc: Fix SLI3 commands being issued on SLI4 devices
During debug, it was seen that the driver is issuing commands specific to
SLI3 on SLI4 devices. Although the adapter correctly rejected the command,
this should not be done.

Revise the code to stop sending these commands on a SLI4 adapter.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 12:57:02 -04:00
James Smart
9b16406864 scsi: lpfc: Fix use-after-free mailbox cmd completion
When unloading the driver, mailbox commands may be sent without holding a
reference on the ndlp. By the time the mailbox command completes, the ndlp
may have reduced its ref counts and been freed.  The problem was reported
by KASAN.

While unregistering due to driver unload, have the completion noop'd by
setting the ndlp context NULL'd. Due to the unload, no further action was
necessary.  Also, while reviewing this path, the generic nulling of the
context after handling should be slightly moved.

Reported by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 12:57:01 -04:00
James Smart
50e3f871fb scsi: lpfc: Resolve irq-unsafe lockdep heirarchy warning in lpfc_io_free
A patch in the 12.2.0.0 set caused a new lockdep warning:

  WARNING: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected
  5.0.0-rc8-next-20190301-dbg+ #1 Not tainted

  Possible interrupt unsafe locking scenario:
       CPU0                    CPU1
       ----                    ----
  lock(&(&qp->io_buf_list_put_lock)->rlock);
                               local_irq_disable();
                               lock(&(&phba->hbalock)->rlock);
                               lock(&(&qp->io_buf_list_put_lock)->rlock);
  <Interrupt>
    lock(&(&phba->hbalock)->rlock);

see: https://www.spinics.net/lists/linux-scsi/msg128389.html

In summary, the new patch added taking the io_buf_list_put_lock while under
an irq-disabled hbalock. This created a lock heirarchy dependent upon irq
being disabled, and there are paths that take the io_buf_list_put_lock
without disabling irq.

Looking at the lpfc_io_free routine, which is where the new heirarchy was
introduced, there is no reason to be taking out the hbalock and raising
irq, as the functionality is replaced by the io_buf_list_xxx locks.

Resolve by removing the hbalock/irq calls in lpfc_io_free.

Fixes: 5e5b511d8b ("scsi: lpfc: Partition XRI buffer list across Hardware Queues")
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 12:57:01 -04:00
James Smart
ff6bf89717 scsi: lpfc: Resolve inconsistent check of hdwq in lpfc_scsi_cmd_iocb_cmpl
A prior patch which added support for non-uniform allocation of MSIX
vectors now causes a smatch complaint:

 drivers/scsi/lpfc/lpfc_scsi.c:3674 lpfc_scsi_cmd_iocb_cmpl()
   error: we previously assumed 'phba->sli4_hba.hdwq' could be
          null (see line 3667)

Resolve by removing the unnecessary check for a NULL hdwq table.

Fixes 6a828b0f61: ("scsi: lpfc: Support non-uniform allocation of MSIX vectors to hardware queues")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 12:57:01 -04:00
Neil Armstrong
9e05e49c29 clk: meson-g12a: fix VPU clock parents
First two VPU clock parents are wrong, fix it here.

Fixes: 085a4ea93d ("clk: meson: g12a: add peripheral clock controller")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lkml.kernel.org/r/20190313135503.3198-1-narmstrong@baylibre.com
2019-03-19 17:38:41 +01:00
Maxime Jourdan
f53b9f146f clk: meson: g12a: fix VPU clock muxes mask
There are 8 parents, use 0x7

Fixes: 085a4ea93d ("clk: meson: g12a: add peripheral clock controller")
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20190319082611.6215-1-mjourdan@baylibre.com
2019-03-19 17:38:00 +01:00
Maxime Jourdan
9b70c697e8 clk: meson-gxbb: round the vdec dividers to closest
We want the video decoder clocks to always round to closest. While the
muxes are already using CLK_MUX_ROUND_CLOSEST, the corresponding
CLK_DIVIDER_ROUND_CLOSEST was forgotten for the dividers.

Fix this by adding the flag to the two vdec dividers.

Fixes: a565242eb9 ("clk: meson: gxbb: add the video decoder clocks")
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20190319102537.2043-1-mjourdan@baylibre.com
2019-03-19 17:36:37 +01:00
Stephen Smalley
ccd19d4caf scripts/selinux: fix build
We need to add the object tree include directory to the include path
for building mdp in order to pick up generated/autoconf.h. Otherwise,
make O=/path/to/objtree breaks.

Fixes: e37c1877ba ("scripts/selinux: modernize mdp")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <paul@paul-moore.com>
2019-03-19 12:29:04 -04:00
Himanshu Madhani
06f3045902 scsi: qla2xxx: Update driver version to 10.01.00.15-k
This version includes support for ISP28XX.

Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 12:22:55 -04:00
Michael Hernandez
3f006ac342 scsi: qla2xxx: Secure flash update support for ISP28XX
This patch adds support for Secure flash update with ISP28xx.

Signed-off-by: Michael Hernandez <mhernandez@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 12:22:55 -04:00
Joe Carnuccio
5fa8774c7f scsi: qla2xxx: Add 28xx flash primary/secondary status/image mechanism
Includes the following:
- correction to 27xx image status struct;
- factoring of 27xx image status validating routines to make common;
- image status generation compare that works across zero wrap;
- bsg interface to report current active images (as loaded by driver).

Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Mike Hernandez <mhernandez@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 12:22:55 -04:00
Joe Carnuccio
ce0366df54 scsi: qla2xxx: Simplification of register address used in qla_tmpl.c
Reduce stack space on each fwdt routine by eliminating local variable reg.

Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 12:22:55 -04:00
Joe Carnuccio
2ff0167151 scsi: qla2xxx: Correction and improvement to fwdt processing
This patch cleans up and fixes firmware dump template processing. These
changes are added to support newer features for ISP27XX/ISP28XX.

Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 12:22:55 -04:00
Joe Carnuccio
3695310e37 scsi: qla2xxx: Update flash read/write routine
This patch makes following changes to flash access routines:

- update return type for read_optrom
- use void instead of uint32_t * for buffer parameter in read
  and write optrom routines
- fix flash/nvram addressing

Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 12:22:55 -04:00
Joe Carnuccio
a28d9e4ef9 scsi: qla2xxx: Add support for multiple fwdump templates/segments
This patch adds multipe firmware dump template and segments support for
ISP27XX/28XX.

Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 12:22:54 -04:00
Joe Carnuccio
f8f97b0c5b scsi: qla2xxx: Cleanups for NVRAM/Flash read/write path
This patch does following:

 - Clean up NVRAM code.
 - Optimizes reading of primary/secondary flash image validation.
 - Remove 0xff mask and make correct width in FLT structure.
 - Use endian macros to assign static fields in fwdump header.
 - Correct fdwt checksum calculation.
 - Simplify ql_dump_buffer() interface usage.
 - Add endianizers to 27xx firmware image validator.
 - fixes compiler warnings for big endian architecture.

Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 12:22:54 -04:00
Joe Carnuccio
72a92df210 scsi: qla2xxx: Correctly report max/min supported speeds
This patch fixes reported speed for min_link and max_supported speed. Also
rename sysfs nodes link_speed and max_supported to be consistent with
{min|max}_suuported_speed.

Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Mike Hernandez <mhernandez@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 12:22:54 -04:00
Joe Carnuccio
2a3192a3f3 scsi: qla2xxx: Add Serdes support for ISP28XX
This patch adds sysfs node for serdes_version and also cleans up port_speed
display.

Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 12:22:54 -04:00
Joe Carnuccio
ecc89f25e2 scsi: qla2xxx: Add Device ID for ISP28XX
This patch adds PCI device ID ISP28XX for Gen7 support.  Also signature
determination for primary/secondary flash image for ISP27XX/28XX is aded as
part of Gen7 support.

Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 12:22:54 -04:00
Joe Carnuccio
24ef8f7eb5 scsi: qla2xxx: Fix routine qla27xx_dump_{mpi|ram}()
This patch fixes qla27xx_dump_{mpi|ram} api for ISP27XX.

Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 12:22:54 -04:00
Joe Carnuccio
2ff6ae85d5 scsi: qla2xxx: Remove FW default template
This patch removes FW default template as there will never be case where
the default template would be invoked.

Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 12:22:54 -04:00
Joe Carnuccio
df617ffbbc scsi: qla2xxx: Add fw_attr and port_no SysFS node
This patch adds new sysfs node to display firmware attributes and port
number.

Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-19 12:22:54 -04:00
David Arcari
2a95496634 tools/power turbostat: return the exit status of a command
turbostat failed to return a non-zero exit status even though the
supplied command (turbostat <command>) failed.  Currently when turbostat
forks a command it returns zero instead of the actual exit status of the
command.  Modify the code to return the exit status.

Signed-off-by: David Arcari <darcari@redhat.com>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2019-03-19 16:51:16 +01:00
YueHaibing
0e3edd9444 drivers: base: swnode: Make two functions static
Fix sparse warning:

drivers/base/swnode.c:475:22: warning: symbol 'software_node_get_parent' was not declared. Should it be static?
drivers/base/swnode.c:484:22: warning: symbol 'software_node_get_next_child' was not declared. Should it be static?

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2019-03-19 16:37:56 +01:00
Stanislaw Gruszka
7dfc45e628 mt76x02: do not enable RTS/CTS by default
My commit 26a7b54731 ("mt76x02: set protection according to ht
operation element") enabled by default RTS/CTS protection for OFDM
and CCK traffic, because MT_TX_RTS_CFG_THRESH is configured to non
0xffff by initvals and .set_rts_threshold callback is not called by
mac80211 on initialization, only on user request or during
ieee80211_reconfig() (suspend/resuem or restart_hw).

Enabling RTS/CTS cause some problems when sending probe request
frames by hcxdumptool penetration tool, but I expect it can cause
other issues on different scenarios.

Restore previous setting of RTS/CTS being disabled by default for
OFDM/CCK by changing MT_TX_RTS_CFG_THRESH initvals to 0xffff.

Fixes: 26a7b54731 ("mt76x02: set protection according to ht operation element")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-03-19 17:37:25 +02:00
Lorenzo Bianconi
13f61dfc52 mt76: fix schedule while atomic in mt76x02_reset_state
Fix following schedule while atomic in mt76x02_reset_state
since synchronize_rcu is run inside a RCU section

[44036.944222] mt76x2e 0000:06:00.0: MCU message 31 (seq 3) timed out
[44036.944281] BUG: sleeping function called from invalid context at kernel/rcu/tree_exp.h:818
[44036.944284] in_atomic(): 1, irqs_disabled(): 0, pid: 28066, name: kworker/u4:1
[44036.944287] INFO: lockdep is turned off.
[44036.944292] CPU: 1 PID: 28066 Comm: kworker/u4:1 Tainted: G        W         5.0.0-rc7-wdn-t1+ #7
[44036.944294] Hardware name: Dell Inc. Studio XPS 1340/0K183D, BIOS A11 09/08/2009
[44036.944305] Workqueue: phy1 mt76x02_wdt_work [mt76x02_lib]
[44036.944308] Call Trace:
[44036.944317]  dump_stack+0x67/0x90
[44036.944322]  ___might_sleep.cold.88+0x9f/0xaf
[44036.944327]  rcu_blocking_is_gp+0x13/0x50
[44036.944330]  synchronize_rcu+0x17/0x80
[44036.944337]  mt76_sta_state+0x138/0x1d0 [mt76]
[44036.944349]  mt76x02_wdt_work+0x1c9/0x610 [mt76x02_lib]
[44036.944355]  process_one_work+0x2a5/0x620
[44036.944361]  worker_thread+0x35/0x3e0
[44036.944368]  kthread+0x11c/0x140
[44036.944376]  ret_from_fork+0x3a/0x50
[44036.944384] BUG: scheduling while atomic: kworker/u4:1/28066/0x00000002
[44036.944387] INFO: lockdep is turned off.
[44036.944389] Modules linked in: cmac ctr ccm af_packet snd_hda_codec_hdmi

Introduce __mt76_sta_remove in order to run sta_remove without holding dev->mutex.
Move __mt76_sta_remove outside of RCU section in mt76x02_reset_state

Fixes: e4ebb8b403d1 ("mt76: mt76x2: implement full device restart on watchdog reset")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-03-19 17:36:41 +02:00
Felix Fietkau
f2a00a821a mt76: mt7603: use the correct hweight8() function
__sw_hweight8() is only defined if CONFIG_GENERIC_HWEIGHT is enabled.
The function that works on all architectures is hweight8().

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-03-19 17:35:37 +02:00
Stanislaw Gruszka
40b941611b mt76x02u: check chip version on probe
Since some USB device IDs are duplicated between mt76x0u, mt7601u
and mt76x2u device, check chip version on probe and return error if
not match the driver.

Don't think this is serious issue, probe most likely will fail at
some other point for wrong device, but we do not have to configure
it if we know is not our device.

Reported-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-03-19 17:33:33 +02:00
Stanislaw Gruszka
c031647068 mt7601u: check chip version on probe
Since some USB device IDs are duplicated between mt7601u and mt76x0u
devices, check chip version on probe and return error if not match
0x7601.

Don't think this is serious issue, probe most likely will fail at
some other point for wrong device, but we do not have to configure
it if we know is not mt7601u device.

Reported-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-03-19 17:31:03 +02:00
Stefan Schmidt
86008304dc Merge remote-tracking branch 'net/master' 2019-03-19 16:25:37 +01:00