This driver does not really need struct as3711_regulator_info and
struct as3711_regulator, remove them.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver is using regulator core's simplified DT parsing code,
so regulator will call regulator_of_get_init_data() to get init_data.
No need to set config.init_data. In additional, current code does not
properly set the init_data setting, so just remove it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add BYT_RT5651_JD_NOT_INV quirk for devices with an inverted
(active-high instead of the normal active-low) jack-detect switch.
And add a quirk for the Complet Electro Serv MY8307 tablet which has
an inverted jack-detect switch (and a mono-speaker).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some boards use a jack-receptacle with a switch which reports the
jack-inserted status as active-high, rather then the standard active-low
reporting most jacks use.
This commit adds support for it. This is activated by a boolean
"realtek,jack-detect-not-inverted" device-property. The not-inverted
in the device-property name, rather then active-high, was chosen to keep
the device-property naming consistent with the rt5640 codec driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add suspend and resume sleep callbacks to STM32 SPDIFRX driver,
to support system low power modes.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code is using devm_regulator_register() so it is not necessary
to save as3722_regs->rdevs[id] for clean up.
The *rdevs[] is not used now, remove it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove #ifdef CONFIG_OF guard so linux/of.h will be included when
!CONFIG_OF. This fixes build warnings when !CONFIG_OF.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dpcm get from fe_clients/be_clients
may be free before use
Add a spin lock at snd_soc_card level,
to protect the dpcm instance.
The lock may be used in atomic context, so use spin lock.
possible race condition between
void dpcm_be_disconnect(
...
list_del(&dpcm->list_be);
list_del(&dpcm->list_fe);
kfree(dpcm);
...
and
for_each_dpcm_fe()
for_each_dpcm_be*()
race condition example
Thread 1:
snd_soc_dapm_mixer_update_power()
-> soc_dpcm_runtime_update()
-> dpcm_be_disconnect()
-> kfree(dpcm);
Thread 2:
dpcm_fe_dai_trigger()
-> dpcm_be_dai_trigger()
-> snd_soc_dpcm_can_be_free_stop()
-> if (dpcm->fe == fe)
Excpetion Scenario:
two FE link to same BE
FE1 -> BE
FE2 ->
Thread 1: switch of mixer between FE2 -> BE
Thread 2: pcm_stop FE1
Exception:
Unable to handle kernel paging request at virtual address dead0000000000e0
pc=<> [<ffffff8960e2cd10>] dpcm_be_dai_trigger+0x29c/0x47c
sound/soc/soc-pcm.c:3226
if (dpcm->fe == fe)
lr=<> [<ffffff8960e2f694>] dpcm_fe_dai_do_trigger+0x94/0x26c
Backtrace:
[<ffffff89602dba80>] notify_die+0x68/0xb8
[<ffffff896028c7dc>] die+0x118/0x2a8
[<ffffff89602a2f84>] __do_kernel_fault+0x13c/0x14c
[<ffffff89602a27f4>] do_translation_fault+0x64/0xa0
[<ffffff8960280cf8>] do_mem_abort+0x4c/0xd0
[<ffffff8960282ad0>] el1_da+0x24/0x40
[<ffffff8960e2cd10>] dpcm_be_dai_trigger+0x29c/0x47c
[<ffffff8960e2f694>] dpcm_fe_dai_do_trigger+0x94/0x26c
[<ffffff8960e2edec>] dpcm_fe_dai_trigger+0x3c/0x44
[<ffffff8960de5588>] snd_pcm_do_stop+0x50/0x5c
[<ffffff8960dded24>] snd_pcm_action+0xb4/0x13c
[<ffffff8960ddfdb4>] snd_pcm_drop+0xa0/0x128
[<ffffff8960de69bc>] snd_pcm_common_ioctl+0x9d8/0x30f0
[<ffffff8960de1cac>] snd_pcm_ioctl_compat+0x29c/0x2f14
[<ffffff89604c9d60>] compat_SyS_ioctl+0x128/0x244
[<ffffff8960283740>] el0_svc_naked+0x34/0x38
[<ffffffffffffffff>] 0xffffffffffffffff
Signed-off-by: KaiChieh Chuang <kaichieh.chuang@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some amplifier may not have a GPIO to control the power, but instead simply
rely on the regulator to power up and down the amplifier.
In order to support those setups, let's make the GPIO optional.
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If SoC has extended Audio DMAC peri peri address,
DT needs to select it.
Otherwise, it can select normal Audio DMAC peri peri address.
Extended Audio DMAC peri peri address can use BUSIF4-7,
normal address can't.
Reported-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mark Brown <broonie@kernel.org>
reg is missing "Audio DMAC peri peri" part,
and reg-name itself is missing at Document.
This patch add these.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mark Brown <broonie@kernel.org>
The reference to '__vermagic' is a relict from v2.5 times. And even
there it had a very short life time, from v2.5.59 (commit 1d411b80ee18
("Module Sanity Check") in the historic tree) to v2.5.69 (commit
67ac5b866bda ("[PATCH] complete modinfo section")).
Neither current kernels nor modules contain a '__vermagic' section any
more, so get rid of it.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jessica Yu <jeyu@kernel.org>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Switch to bitmap_zalloc() to show clearly what we are allocating.
Besides that it returns pointer of bitmap type instead of opaque void *.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Building with clang finds a mistaken __init tag:
WARNING: vmlinux.o(.text+0x5e4250): Section mismatch in reference from the function davinci_mmcsd_probe() to the function .init.text:init_mmcsd_host()
The function davinci_mmcsd_probe() references
the function __init init_mmcsd_host().
This is often because davinci_mmcsd_probe lacks a __init
annotation or the annotation of init_mmcsd_host is wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
clang points out several instances of mismatched types in this drivers,
all coming from a single declaration:
drivers/mmc/host/pxamci.c:193:15: error: implicit conversion from enumeration type 'enum dma_transfer_direction' to
different enumeration type 'enum dma_data_direction' [-Werror,-Wenum-conversion]
direction = DMA_DEV_TO_MEM;
~ ^~~~~~~~~~~~~~
drivers/mmc/host/pxamci.c:212:62: error: implicit conversion from enumeration type 'enum dma_data_direction' to
different enumeration type 'enum dma_transfer_direction' [-Werror,-Wenum-conversion]
tx = dmaengine_prep_slave_sg(chan, data->sg, host->dma_len, direction,
The behavior is correct, so this must be a simply typo from
dma_data_direction and dma_transfer_direction being similarly named
types with a similar purpose.
Fixes: 6464b71409 ("mmc: pxamci: switch over to dmaengine use")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
saved-context in byt_gpio_probe is allocated via devm_kcalloc and is
used without checking for NULL in later functions. This patch avoids
such a scenario.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This adds an additional backlight property as described
in panel-common.txt
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This panel has a backlight, so fetch it from devicetree using the
corresponding property as documented in panel-common.txt. It is
implemented the same way as in panel-dpi.c
This ensures the backlight is also disabled when the display is
turned off like when doing xset dpms force off.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently dsi_display_init_dsi() calls dss_pll_enable() but it is not
paired with dss_pll_disable() in dsi_display_uninit_dsi(). This leaves
the DSS clocks enabled when the display is blanked wasting about extra
5mW of power while idle.
The clock that is left on by not calling dss_pll_disable() is
DSS_CLKCTRL bit 10 OPTFCLKEN_SYS_CLK that is the source clock for
DSI PLL.
We can fix this issue by by making the current dsi_pll_uninit() into
dsi_pll_disable(). This way we can just call dss_pll_disable() from
dsi_display_uninit_dsi() and the code becomes a bit easier to follow.
However, we need to also consider that DSI PLL can be muxed for DVI too
as pointed out by Tomi Valkeinen <tomi.valkeinen@ti.com>. In the DVI
case, we want to unconditionally disable the clocks. To get around this
issue, we separate out the DSI lane handling from dsi_pll_enable() and
dsi_pll_disable() as suggested by Tomi in an earlier experimental patch.
So we must only toggle the DSI regulator based on the vdds_dsi_enabled
flag from dsi_display_init_dsi() and dsi_display_uninit_dsi().
We need to make these two changes together to avoid breaking things
for DVI when fixing the DSI clock handling. And this all causes a
slight renumbering of the error path for dsi_display_init_dsi().
Suggested-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This allows nicer kerneldoc with an easy way to reference the enum and
the values.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Panels are now supported through the drm_panel infrastructure, remove
the omapdrm-specific driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Those components are supported by the drm_bridge infrastructure, remove
the omapdrm-specific driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omapdss driver patches DT at runtime to prepend an "omapdss," prefix
to the compatible string of all encoders, panels and connectors. This
mechanism ensures they get bound to the omapdss-specific drivers instead
of generic drivers.
Now that we have drm_bridge support in omapdrm, we need to selectively
disable this mechanism. Add a whitelist of compatible strings to patch,
and fill it with all the devices we support. They will be removed one by
one once corresponding drm_bridge drivers become available and get
successfully tested with omapdrm.
The omapdss components load check code is updated accordingly to ignore
devices managed by external bridge drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Hook up drm_panel support in the omapdrm driver. The change is
relatively simply as the way has been paved by drm_bridge support
already. In addition to looking up, attaching to and detaching from the
panel, we only need to add panel support in the connector .get_modes()
handler, take connector bus flags (set by the panel) into account, and
enable/disable the panel in the encoder enable/disable operations
handlers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Hook up drm_bridge support in the omapdrm driver. Despite the recent
extensive preparation work, this is a rather intrusive change, as the
management of outputs needs to be adapted through the driver to handle
both omap_dss_device and drm_bridge.
Connector creation is skipped when using a drm_bridge, as the bridge
creates the connector internally. This creates issues with systems that
split connector operations (such as modes retrieval and hot-plug
detection) across different bridges. These systems can't be supported
using drm_bridge for now (their support through the omap_dss_device
infrastructure is not affected), this will be fixed in subsequent
changes.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add support for the OSD070T1718-19TS 7" 800x480 panel from One Stop
Displays to the panel-simple driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The OSD Displays OSD070T1718-19TS is a 7" WVGA (800x480) 24bit RGB panel
and is compatible with the simple-panel bindings.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OSD Displays is a panel manufacturer. It has been acquired by New Vision
Displays in 2015 but continues to operate under its own brand name.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The TFP410 supports configurable pixel clock sampling edge and data
de-skew adjustments. The configuration can be set through I2C or
dedicated chip pins.
Report the configuration through the drm_bridge timings. As the
ti-tftp410 driver doesn't support configuring the chip through I2C, we
simply use the default configuration in that case. When the chip is
configured through dedicated pins, we parse the configuration from DT.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The TFP410 has a powerdown pin that can be connected to a GPIO to
control power saving. The DT bindings define a corresponding property,
but the driver doesn't implement support for it. Fix that.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The TI TFP410 is a DVI encoder, not a full HDMI encoder. Its output can
be routed to a DVI-D connector, even if in many cases embedded systems
will use an HDMI connector to carry the DVI signals.
Instead of hardcoding the connector type to HDMI, retrieve the connector
type from its DT node.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The TFP410 supports configuration of several input bus parameters
through either the I2C port or chip pins. In the latter case, we need to
specify those parameters in DT.
Two new properties are added, ti,deskew to specify the data de-skew
configuration (as set through the DK[3:1] pins), and pclk-sample to
specify the pixel clock sampling edge (as set through the EDGE pin).
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DRM bus flags convey additional information on pixel data on
the bus. All current available bus flags might be of interest for
a bridge. Remove the sampling_edge field and use bus_flags.
In the case at hand a dumb VGA bridge needs a specific data enable
polarity (DRM_BUS_FLAG_DE_LOW).
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DRM_BUS_FLAG_PIXDATA_(POS|NEG)EDGE and
DRM_BUS_FLAG_SYNC_(POS|NEG)EDGE flags are deprecated in favour of the
new DRM_BUS_FLAG_PIXDATA_(DRIVE|SAMPLE)_(POS|NEG)EDGE and
new DRM_BUS_FLAG_SYNC_(DRIVE|SAMPLE)_(POS|NEG)EDGE flags. Replace them
through the code.
This effectively changes the value of the .sampling_edge bridge timings
field in the dumb-vga-dac driver. This is safe to do as no driver
consumes these values yet.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DRM_BUS_FLAG_PIXDATA_POSEDGE and DRM_BUS_FLAG_PIXDATA_NEGEDGE macros
and their DRM_BUS_FLAG_SYNC_* counterparts define on which pixel clock
edge data and sync signals are driven. They are however used in some
drivers to define on which pixel clock edge data and sync signals are
sampled, which should usually (but not always) be the opposite edge of
the driving edge. This creates confusion.
Create four new macros for both PIXDATA and SYNC that explicitly state
the driving and sampling edge in their name to remove the confusion. The
driving macros are defined as the opposite of the sampling macros to
made code simpler based on the assumption that the driving and sampling
edges are opposite.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omap_dss_device type and output_type fields differ mostly for
historical reasons. The output_type field is required for all devices
but the display at the end of the pipeline, and must be set to
OMAP_DISPLAY_TYPE_NONE for the latter. The type field is required for
all devices but the internal encoder, for which it is ignored.
The only reason why the output_type field must be set to
OMAP_DISPLAY_TYPE_NONE for the display at the end of the pipeline is to
identify omap_dss_device instances corresponding to displays. This is
not documented and confusing.
Clean the code by adding a new display field to the omap_dss_device
structure to identify displays, and merge the type and output_type
fields.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omapdrm driver initialization procedure starts by connecting all
available pipelines, gathering related information (such as output and
display DSS devices, and DT aliases), sorting them by alias, and finally
creates all the DRM/KMS objects.
When using DRM bridges instead of DSS devices, we will need to attach to
the bridges before getting the aliases. As attaching to bridges requires
an encoder object, we have to reorganize the initialization sequence to
create encoders before getting aliases and sorting the pipelines.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Now that the direction of OF graph walk has been reversed, there's no
need to lookup devices by port as we have no sink device connected
through multiple sink ports. Simplify OF lookup of the DSS devices to
look them up by node only.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DPI and SDI encoders store the full videomode upon mode set, to only
use the value of the pixel clock when enabling the encoder. This wastes
memory. Store the pixel clock value only.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Replace internal usage of struct videomode with struct drm_display_mode
in order to avoid converting needlessly between the data structures.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omap_dss_device .check_timings() and .set_timings() operations
operate on struct videomode, while the DRM API operates on struct
drm_display_mode. This forces conversion from to videomode in the
callers. While that's not a problem per se, it creates a difference with
the drm_bridge API.
Replace the videomode parameter to the .check_timings() and
.set_timings() operations with a drm_display_mode. This pushed the
conversion to videomode down to the DSS devices in some cases. If needed
they will be converted to operate on drm_display_mode natively.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The encoder .atomic_check() and connector .mode_valid() operations both
walk through the dss devices in the pipeline to validate the mode.
Factor out the common code in a new omap_drm_connector_mode_fixup()
function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The mode setting handler of the VENC stores the video mode internally,
to then convert it to a configuration when programming the hardware. The
stored mode is otherwise unused. Cache the configuration directly
instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DISPC timings checks relate to the CRTC, but they're performed in
the encoder and connector .atomic_check() and .mode_valid() operations.
Move them to the CRTC .mode_valid() operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The field is only used to check whether the device is connected, and we
can do so by checking the dss field instead. Remove the src field.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
For HDMI pipelines, when the output gets disconnected the device
handling CEC needs to be notified. Instead of guessing which device that
would be (and sometimes getting it wrong), notify all devices in the
pipeline.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>