The minimum supported gcc version is >= 4.6, so these can be removed.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190111084931.24601-1-linux@rasmusvillemoes.dk
I noticed a link that didn't work ...
Fixes: 1f2db3034c ("drm: of: introduce drm_of_find_panel_or_bridge")
Cc: Rob Herring <robh@kernel.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190111164048.29067-2-daniel.vetter@ffwll.ch
kbuild reported a build faile in [1]. This is triggered when CONFIG_IPC_NS
is not set. So let's make the use of init_ipc_ns conditional on
CONFIG_IPC_NS being set.
[1]: https://lists.01.org/pipermail/kbuild-all/2019-January/056903.html
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_SCSI_UFS_QCOM selects CONFIG_PHY_QCOM_UFS, assuming that this was
the only possible PHY driver Qualcomm's UFS controller would use. But in
SDM845, the UFS driver is bundled into phy-qcom-qmp, and phy-qcom-ufs is
unused.
Remove the select, since for SDM845 it adds useless drivers to the build.
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In case of ->set_param() and ->bind_conn() cxgb4i driver does not wait for
cmd completion, this can create race conditions, to avoid this add
wait_for_completion().
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After Commit 54aed4dd35 ("MIPS: IP27: use dma_direct_ops") qla1280 driver
failed on SGI IP27 machines with
qla1280: QLA1040 found on PCI bus 0, dev 0
qla1280 0000:00:00.0: enabling device (0006 -> 0007)
qla1280: Failed to get request memory
qla1280: probe of 0000:00:00.0 failed with error -12
Reason is that SGI IP27 always generates 64bit DMA addresses and has no
fallback mode for 32bit DMA addresses implemented. QLA1280 supports 64bit
addressing for all DMA accesses so setting coherent mask to 64bit fixes the
issue.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Albeit we no longer rely on those hard-coded descriptor sizes, we still use
them as our defaults, so better get it right. While adding its sysfs
entries, we forgot to update the geometry descriptor size. It is 0x48
according to UFS2.1, and wasn't changed in UFS3.0.
[mkp: typo]
Fixes: c720c09122 (scsi: ufs: sysfs: geometry descriptor)
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The tmscsim.txt doc file was removed in c121107d0f.
Fixes: c121107d0f ("scsi: documentation: Obsolete documentation references")
Signed-off-by: Otto Sabart <ottosabart@seberm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
commit 272652fcbf ("scsi: megaraid_sas: add retry logic in megasas_readl")
missed changing readl to megasas_readl in megasas_clear_intr_fusion(). For
Aero controllers, reads of outbound_intr_status register needs to be
retried.
Reported-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the driver finds invalid destination MAC for the first un-reachable
target, and before completes the PATH_REQ operation, set new ep_state to
OFFLDCONN_NONE so that as part of driver ep_poll mechanism, the upper
open-iscsi layer is notified to complete the login process on the first
un-reachable target and thus proceed login to other reachable targets.
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
hba->is_sys_suspended is set after successful system suspend but
not clear after successful system resume.
According to current behavior, hba->is_sys_suspended will not be set if
host is runtime-suspended but not system-suspended. Thus we shall aligh the
same policy: clear this flag even if host remains runtime-suspended after
ufshcd_system_resume is successfully returned.
Simply fix this flag to correct host status logs.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
+----------+ +----------+
| | | |
| |--- 3.0 G ---| |--- 6.0 G --- SAS disk
| | | |
| |--- 3.0 G ---| |--- 6.0 G --- SAS disk
|initiator | | |
| device |--- 3.0 G ---| Expander |--- 6.0 G --- SAS disk
| | | |
| |--- 3.0 G ---| |--- 6.0 G --- SATA disk -->failed to connect
| | | |
| | | |--- 6.0 G --- SATA disk -->failed to connect
| | | |
+----------+ +----------+
According to Serial Attached SCSI - 1.1 (SAS-1.1):
If an expander PHY attached to a SATA PHY is using a physical link rate
greater than the maximum connection rate supported by the pathway from an
STP initiator port, a management application client should use the SMP PHY
CONTROL function (see 10.4.3.10) to set the PROGRAMMED MAXIMUM PHYSICAL
LINK RATE field of the expander PHY to the maximum connection rate
supported by the pathway from that STP initiator port.
Currently libsas does not support checking if this condition occurs, nor
rectifying when it does.
Such a condition is not at all common, however it has been seen on some
pre-silicon environments where the initiator PHY only supports a 1.5 Gbit
maximum linkrate, mated with 12G expander PHYs and 3/6G SATA phy.
This patch adds support for checking and rectifying this condition during
initial device discovery only.
We do support checking min pathway connection rate during revalidation phase,
when new devices can be detected in the topology. However we do not
support in the case of the the user reprogramming PHY linkrates, such that
min pathway condition is not met/maintained.
A note on root port PHY rates:
The libsas root port PHY rates calculation is broken. Libsas sets the
rates (min, max, and current linkrate) of a root port to the same linkrate
of the first PHY member of that same port. In doing so, it assumes that
all other PHYs which subsequently join the port to have the same
negotiated linkrate, when they could actually be different.
In practice this doesn't happen, as initiator and expander PHYs are
normally initialised with consistent min/max linkrates.
This has not caused an issue so far, so leave alone for now.
Tested-by: Jian Luo <luojian5@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the SMP PHY control execution result is checked, however the
function result for the command is not.
As such, we may be missing all potential errors, like SMP FUNCTION FAILED,
INVALID REQUEST FRAME LENGTH, etc., meaning the PHY control request has
failed.
In some scenarios we need to ensure the function result is accepted, so add
a check for this.
Tested-by: Jian Luo <luojian5@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently much indentation in this file is done with whitespaces instead of
tabs, which can make reading difficult, so fix this up.
Some other little minor tidy-up is done, but this file still has many other
checkpatch warnings (generally linelength > 80 or function arguments have
no identifier names).
All libsas code can be audited for checkpatch issues later.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When SGE buffer containing DIF information crosses 4G boundary, it results
in DMA error. This patch fixes this issue by calculating SGE buffer size
and if it crosses 4G boundary, driver will split it into multiple SGE
buffers to avoid DMA error.
Signed-off-by: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Define the required properties to enable I2C bus recovery supported by
the I2C subsystem.
This patch adds GPIO based I2C fault injector for Digi Connectcore SOM.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds definitions for ESDHC1 for Digi Connectore SOM & JSK.
This interface can be used to boot a module.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In fact, the RTC battery can only be connected outside the module,
so this patch moves the PMIC RTC property and its power from SOM dts
to JSK.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The interrupt controller is located at the physical address 0x10040000.
This patch changes the unit name of the controller to reflect the actual
address.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Allow user to selectively enable/disable DIF/DIX protection
capabilities mask.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When SCSI-MQ is enabled, in some case system would present
nr_possible_cpus() which is greater than requested vectors by the
driver. This results into driver being able to get larger number of MSI-X
vectors than actual online CPUs. Driver then uses
pci_alloc_irq_vectors_affinity() to assign 1:1 mapping and affinity for
each MSI-x vector to CPUs. When the command is submitted using MSI-x
vector, assigned to offline CPU, it results in an ABTS and system
hang. This hang is result of a driver not being able to process interrupt
on a vector assigned to an Off-line CPUs
This patch fixes this issue by setting irq_offset value for the
blk_mq_pci_map_queues() to use only those CPUs which has CPU mask affinity
assigned and are online. By using the irq_offset value, driver will allow
online cpumask to decide which vectors are used in blk_mq_pci_map_queues().
Fixes: 5601236b6f ("scsi: qla2xxx: Add Block Multi Queue functionality.")
Cc: <stable@vger.kernel.org> #4.19
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
One of the more common cases of allocation size calculations is finding the
size of a structure that has a zero-sized array at the end, along with memory
for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can now
use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that, in some cases, I replaced "FALLTHROUGH" with a "fall through"
annotation and then placed it at the bottom of the corresponding switch
case, which is what GCC is expecting to find.
Addresses-Coverity-ID: 114961 ("Missing break in switch")
Addresses-Coverity-ID: 114962 ("Missing break in switch")
Addresses-Coverity-ID: 114963 ("Missing break in switch")
Addresses-Coverity-ID: 114964 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Most of the legacy "gpio-key,wakeup" and "enable-sdio-wakeup" boolean
properties are already replaced with "wakeup-source". However few
occurrences of old property has popped up again, probably from the
remnants in downstream trees. Almost all of those were remove couple
of years back.
Replace the legacy properties with the unified "wakeup-source" property
introduced in the commit 700a38b27e ("Input: gpio_keys - switch to using
generic device properties") and commit 0dbcdc0622 ("mmc: core: enable
support for the standard "wakeup-source" property")
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that, in this particular case, I replaced "!!! fall through !!!"
comment with "fall through" annotations, which is what GCC is expecting to
find.
Addresses-Coverity-ID: 146155 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that I replaced "!! fall through !!" and "!!! fall through !!!"
comments with "fall through" annotations, which is what GCC is expecting to
find.
Addresses-Coverity-ID: 744899 ("Missing break in switch")
Addresses-Coverity-ID: 744900 ("Missing break in switch")
Addresses-Coverity-ID: 744901 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that, in this particular case, I replaced "!!! fall through !!!"
with a "fall through" annotation, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Bradley Grove <bgrove@atto.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Addresses-Coverity-ID: 114994 ("Missing break in switch")
Addresses-Coverity-ID: 114995 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently we set the protection parameters after calling scsi_add_host()
for v3 hw.
They should be set beforehand, so make this change.
Appearantly this fixes our DIX issue (not mainline yet) also, but more
testing required.
Fixes: d6a9000b81 ("scsi: hisi_sas: Add support for DIF feature for v2 hw")
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Matteo reported forwarding issues inside the linux bridge,
if the enslaved interfaces use the fq qdisc.
Similar to commit 8203e2d844 ("net: clear skb->tstamp in
forwarding paths"), we need to clear the tstamp field in
the bridge forwarding path.
Fixes: 80b14dee2b ("net: Add a new socket option for a future transmit time.")
Fixes: fb420d5d91 ("tcp/fq: move back to CLOCK_MONOTONIC")
Reported-and-tested-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Taehee Yoo says:
====================
net: bpfilter: fix two bugs in bpfilter
This patches fix two bugs in the bpfilter_umh which are related in
iptables command.
The first patch adds an exit code for UMH process.
This provides an opportunity to cleanup members of the umh_info
to modules which use the UMH.
In order to identify UMH processes, a new flag PF_UMH is added.
The second patch makes the bpfilter_umh use UMH cleanup callback.
The third patch adds re-start routine for the bpfilter_umh.
The bpfilter_umh does not re-start after error occurred.
because there is no re-start routine in the module.
The fourth patch ensures that the bpfilter.ko module will not removed while
it's being used.
The bpfilter.ko is not protected by locks or module reference counter.
Therefore that can be removed while module is being used.
In order to protect that, mutex is used.
The first and second patch are preparation patches for the third and
fourth patch.
TEST #1
while :
do
modprobe bpfilter
kill -9 <pid of the bpfilter_umh>
iptables -vnL
done
TEST #2
while :
do
iptables -I FORWARD -m string --string ap --algo kmp &
iptables -F &
modprobe -rv bpfilter &
done
TEST #3
while :
do
modprobe bpfilter &
modprobe -rv bpfilter &
done
The TEST1 makes a failure of iptables command.
This is fixed by the third patch.
The TEST2 makes a panic because of a race condition in the bpfilter_umh
module.
This is fixed by the fourth patch.
The TEST3 makes a double-create UMH process.
This is fixed by the third and fourth patch.
v4 :
- declare the exit_umh() as static inline
- check stop flag in the load_umh() to avoid a double-create UMH
v3 :
- Avoid unnecessary list lookup for non-UMH processes
- Add a new PF_UMH flag
v2 : add the first and second patch
v1 : Initial patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The bpfilter_umh will be stopped via __stop_umh() when the bpfilter
error occurred.
The bpfilter_umh() couldn't start again because there is no restart
routine.
The section of the bpfilter_umh_{start/end} is no longer .init.rodata
because these area should be reused in the restart routine. hence
the section name is changed to .bpfilter_umh.
The bpfilter_ops->start() is restart callback. it will be called when
bpfilter_umh is stopped.
The stop bit means bpfilter_umh is stopped. this bit is set by both
start and stop routine.
Before this patch,
Test commands:
$ iptables -vnL
$ kill -9 <pid of bpfilter_umh>
$ iptables -vnL
[ 480.045136] bpfilter: write fail -32
$ iptables -vnL
All iptables commands will fail.
After this patch,
Test commands:
$ iptables -vnL
$ kill -9 <pid of bpfilter_umh>
$ iptables -vnL
$ iptables -vnL
Now, all iptables commands will work.
Fixes: d2ba09c17a ("net: add skeleton of bpfilter kernel module")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now, UMH process is killed, do_exit() calls the umh_info->cleanup callback
to release members of the umh_info.
This patch makes bpfilter_umh's cleanup routine to use the
umh_info->cleanup callback.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A UMH process which is created by the fork_usermode_blob() such as
bpfilter needs to release members of the umh_info when process is
terminated.
But the do_exit() does not release members of the umh_info. hence module
which uses UMH needs own code to detect whether UMH process is
terminated or not.
But this implementation needs extra code for checking the status of
UMH process. it eventually makes the code more complex.
The new PF_UMH flag is added and it is used to identify UMH processes.
The exit_umh() does not release members of the umh_info.
Hence umh_info->cleanup callback should release both members of the
umh_info and the private data.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that, in this particular case, I replaced "allow fall-through" with
a "fall through" annotation, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently there is one cmd timeout timer and one qfull timer for each udev,
and whenever any new command is coming in we will update the cmd timer or
qfull timer. For some corner cases the timers are always working only for
the ringbuffer's and full queue's newest cmd. That's to say the timer won't
be fired even if one cmd has been stuck for a very long time and the
deadline is reached.
This fix will keep the cmd/qfull timers to be pended for the oldest cmd in
ringbuffer and full queue, and will update them with the next cmd's
deadline only when the old cmd's deadline is reached or removed from the
ringbuffer and full queue.
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Acked-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The functions isdn_tty_tiocmset() and isdn_tty_set_termios() may be
concurrently executed.
isdn_tty_tiocmset
isdn_tty_modem_hup
line 719: kfree(info->dtmf_state);
line 721: kfree(info->silence_state);
line 723: kfree(info->adpcms);
line 725: kfree(info->adpcmr);
isdn_tty_set_termios
isdn_tty_modem_hup
line 719: kfree(info->dtmf_state);
line 721: kfree(info->silence_state);
line 723: kfree(info->adpcms);
line 725: kfree(info->adpcmr);
Thus, some concurrency double-free bugs may occur.
These possible bugs are found by a static tool written by myself and
my manual code review.
To fix these possible bugs, the mutex lock "modem_info_mutex" used in
isdn_tty_tiocmset() is added in isdn_tty_set_termios().
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vsock core only supports 32bit CID, but the Virtio-vsock spec define
CID (dst_cid and src_cid) as u64 and the upper 32bits is reserved as
zero. This inconsistency causes one bug in vhost vsock driver. The
scenarios is:
0. A hash table (vhost_vsock_hash) is used to map an CID to a vsock
object. And hash_min() is used to compute the hash key. hash_min() is
defined as:
(sizeof(val) <= 4 ? hash_32(val, bits) : hash_long(val, bits)).
That means the hash algorithm has dependency on the size of macro
argument 'val'.
0. In function vhost_vsock_set_cid(), a 64bit CID is passed to
hash_min() to compute the hash key when inserting a vsock object into
the hash table.
0. In function vhost_vsock_get(), a 32bit CID is passed to hash_min()
to compute the hash key when looking up a vsock for an CID.
Because the different size of the CID, hash_min() returns different hash
key, thus fails to look up the vsock object for an CID.
To fix this bug, we keep CID as u64 in the IOCTLs and virtio message
headers, but explicitly convert u64 to u32 when deal with the hash table
and vsock core.
Fixes: 834e772c8d ("vhost/vsock: fix use-after-free in network stack callers")
Link: https://github.com/stefanha/virtio/blob/vsock/trunk/content.tex
Signed-off-by: Zha Bin <zhabin@linux.alibaba.com>
Reviewed-by: Liu Jiang <gerry@linux.alibaba.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add this property to all layerscape platforms to improve USB read write performance.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
SCU power domain can be used in the same way by IMX8QXP and IMX8QM SoCs.
Make the driver support the fallback compatible string "fsl,scu-pd" to
allow other SoCs to reuse the common part.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>