Add a new PID 0x7843 to the driver.
Let the new products be able to set up 3 serial ports with the driver.
Note that this depends on e8603076f5 ("USB: serial: mos7840: clean up
register handling").
Signed-off-by: JackyChou <jackychou@asix.com.tw>
[ johan: mention dependency in case anyone wants to backport this ]
Signed-off-by: Johan Hovold <johan@kernel.org>
In the read/write function, set port 2 independently in the 2-port case.
When setting the offset of port registers, the offset between port 1 and
other ports is different, so port 1 is set independently.
Then in the rest of ports, the port 2 between 2-ports case and 4-ports case
is different, so port 2 in 2-ports case is set independently.
Specifically, port 2 in the 2-port case maps to the registers used by
port 3 in the 4-port case.
Signed-off-by: JackyChou <jackychou@asix.com.tw>
[ johan: simplify register-offset handling at port probe, add a comment
and amend commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Internal to dax_unlock_mapping_entry(), dax_unlock_entry() is used to
store a replacement entry in the Xarray at the given xas-index with the
DAX_LOCKED bit clear. When called, dax_unlock_entry() expects the unlocked
value of the entry relative to the current Xarray state to be specified.
In most contexts dax_unlock_entry() is operating in the same scope as
the matched dax_lock_entry(). However, in the dax_unlock_mapping_entry()
case the implementation needs to recall the original entry. In the case
where the original entry is a 'pmd' entry it is possible that the pfn
performed to do the lookup is misaligned to the value retrieved in the
Xarray.
Change the api to return the unlock cookie from dax_lock_page() and pass
it to dax_unlock_page(). This fixes a bug where dax_unlock_page() was
assuming that the page was PMD-aligned if the entry was a PMD entry with
signatures like:
WARNING: CPU: 38 PID: 1396 at fs/dax.c:340 dax_insert_entry+0x2b2/0x2d0
RIP: 0010:dax_insert_entry+0x2b2/0x2d0
[..]
Call Trace:
dax_iomap_pte_fault.isra.41+0x791/0xde0
ext4_dax_huge_fault+0x16f/0x1f0
? up_read+0x1c/0xa0
__do_fault+0x1f/0x160
__handle_mm_fault+0x1033/0x1490
handle_mm_fault+0x18b/0x3d0
Link: https://lkml.kernel.org/r/20181130154902.GL10377@bombadil.infradead.org
Fixes: 9f32d22130 ("dax: Convert dax_lock_mapping_entry to XArray")
Reported-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Tested-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When the armada thermal module is inserted, removed and then reinserted,
the system panics as per the messages below. The reason is that "edit"
a live resource in the resource tree twice, and end up with it pointing
to some other hardware.
Editing live resources (resources that are part of the registered
resource tree) is not permissible - the resource tree is an ordered
set of resources, sorted by start address, and when a new resource is
inserted, it is validated that it (a) fits within its parent resource
and (b) does not overlap a neighbouring resource.
Get rid of this resource editing. We can instead adjust the return
value from ioremap() as ioremap() deals with the creation of page-
based mappings - provided the adjustment does not cross a page
boundary.
SError Interrupt on CPU1, code 0xbf000000 -- SError
CPU: 1 PID: 2749 Comm: modprobe Not tainted 4.19.0+ #175
Hardware name: Marvell 8040 MACCHIATOBin Double shot (DT)
pstate: 20400085 (nzCv daIf +PAN -UAO)
pc : regmap_mmio_read+0x3c/0x60
lr : regmap_mmio_read+0x3c/0x60
sp : ffffff800d453900
x29: ffffff800d453900 x28: ffffff800096a1d0
x27: 0000000000000100 x26: ffffff80009696d8
x25: ffffff8000969000 x24: ffffffc13a588918
x23: ffffffc13a9a28a8 x22: ffffff800d4539dc
x21: 0000000000000084 x20: ffffff800d4539dc
x19: ffffffc13a5d5480 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000
x15: 0000000000000000 x14: 0000000000000000
x13: 0000000000000000 x12: 0000000000000030
x11: 0101010101010101 x10: 7f7f7f7f7f7f7f7f
x9 : 0000000000000000 x8 : ffffffc13a5d5a80
x7 : 0000000000000000 x6 : 000000000000003f
x5 : 0000000000000000 x4 : 0000000000000000
x3 : ffffff800851be70 x2 : ffffff800851bd60
x1 : ffffff800d492ff8 x0 : 0000000000000000
Kernel panic - not syncing: Asynchronous SError Interrupt
CPU: 1 PID: 2749 Comm: modprobe Not tainted 4.19.0+ #175
Hardware name: Marvell 8040 MACCHIATOBin Double shot (DT)
Call trace:
dump_backtrace+0x0/0x158
show_stack+0x14/0x1c
dump_stack+0x90/0xb0
panic+0x128/0x298
print_tainted+0x0/0xa8
arm64_serror_panic+0x74/0x80
do_serror+0x5c/0xb8
el1_error+0xb4/0x144
regmap_mmio_read+0x3c/0x60
_regmap_bus_reg_read+0x18/0x20
_regmap_read+0x64/0x180
regmap_read+0x44/0x6c
armada_ap806_init+0x24/0x5c [armada_thermal]
armada_thermal_probe+0x2c8/0x37c [armada_thermal]
platform_drv_probe+0x4c/0xb0
really_probe+0x21c/0x2b4
driver_probe_device+0x58/0xfc
__driver_attach+0xd4/0xd8
bus_for_each_dev+0x50/0xa0
driver_attach+0x20/0x28
bus_add_driver+0x1c4/0x228
driver_register+0x6c/0x124
__platform_driver_register+0x4c/0x54
armada_thermal_driver_init+0x20/0x1000 [armada_thermal]
do_one_initcall+0x30/0x204
do_init_module+0x5c/0x1d4
load_module+0x1a88/0x212c
__se_sys_finit_module+0xa0/0xac
__arm64_sys_finit_module+0x1c/0x24
el0_svc_common+0x94/0xf0
el0_svc_handler+0x24/0x80
el0_svc+0x8/0x3c0
SMP: stopping secondary CPUs
Kernel Offset: disabled
CPU features: 0x0,21806000
Memory Limit: none
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
TCP_NOTSENT_LOWAT socket option or sysctl was added in linux-3.12
as a step to enable bigger tcp sndbuf limits.
It works reasonably well, but the following happens :
Once the limit is reached, TCP stack generates
an [E]POLLOUT event for every incoming ACK packet.
This causes a high number of context switches.
This patch implements the strategy David Miller added
in sock_def_write_space() :
- If TCP socket has a notsent_lowat constraint of X bytes,
allow sendmsg() to fill up to X bytes, but send [E]POLLOUT
only if number of notsent bytes is below X/2
This considerably reduces TCP_NOTSENT_LOWAT overhead,
while allowing to keep the pipe full.
Tested:
100 ms RTT netem testbed between A and B, 100 concurrent TCP_STREAM
A:/# cat /proc/sys/net/ipv4/tcp_wmem
4096 262144 64000000
A:/# super_netperf 100 -H B -l 1000 -- -K bbr &
A:/# grep TCP /proc/net/sockstat
TCP: inuse 203 orphan 0 tw 19 alloc 414 mem 1364904 # This is about 54 MB of memory per flow :/
A:/# vmstat 5 5
procs -----------memory---------- ---swap-- -----io---- -system-- ------cpu-----
r b swpd free buff cache si so bi bo in cs us sy id wa st
0 0 0 256220672 13532 694976 0 0 10 0 28 14 0 1 99 0 0
2 0 0 256320016 13532 698480 0 0 512 0 715901 5927 0 10 90 0 0
0 0 0 256197232 13532 700992 0 0 735 13 771161 5849 0 11 89 0 0
1 0 0 256233824 13532 703320 0 0 512 23 719650 6635 0 11 89 0 0
2 0 0 256226880 13532 705780 0 0 642 4 775650 6009 0 12 88 0 0
A:/# echo 2097152 >/proc/sys/net/ipv4/tcp_notsent_lowat
A:/# grep TCP /proc/net/sockstat
TCP: inuse 203 orphan 0 tw 19 alloc 414 mem 86411 # 3.5 MB per flow
A:/# vmstat 5 5 # check that context switches have not inflated too much.
procs -----------memory---------- ---swap-- -----io---- -system-- ------cpu-----
r b swpd free buff cache si so bi bo in cs us sy id wa st
2 0 0 260386512 13592 662148 0 0 10 0 17 14 0 1 99 0 0
0 0 0 260519680 13592 604184 0 0 512 13 726843 12424 0 10 90 0 0
1 1 0 260435424 13592 598360 0 0 512 25 764645 12925 0 10 90 0 0
1 0 0 260855392 13592 578380 0 0 512 7 722943 13624 0 11 88 0 0
1 0 0 260445008 13592 601176 0 0 614 34 772288 14317 0 10 90 0 0
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .validate phylink callback should empty the supported bitmap when
the interface mode is invalid.
Cc: Maxime Chevallier <maxime.chevallier@bootlin.com>
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp2_phylink_validate() relies on the interface field of
phylink_link_state to determine valid link modes. However, when called
from phylink_sfp_module_insert() this field in not initialized. The
default switch case then excludes 10G link modes. This allows 10G SFP
modules that are detected correctly to be configured at max rate of
2.5G.
Catch the uninitialized PHY mode case, and allow 10G rates.
Fixes: d97c9f4ab0 ("net: mvpp2: 1000baseX support")
Cc: Maxime Chevallier <maxime.chevallier@bootlin.com>
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the ipu-v3 mem2mem image-convert code, with some fixes for race
conditions, alignment issues, and visual artifacts due to tile alignment
and scaling factor issues when scaling images larger than hardware
limitations in multiple tiles. This will allow the V4L2 mem2mem scaler
driver to write output images larger than 1024x1024 pixels.
Also switch drm/imx source files to SPDX license identifiers, constify
struct clk_ops in imx-tve, and add a timeout warning to the busy wait in
ipu_plane_disable().
-----BEGIN PGP SIGNATURE-----
iI0EABYIADUWIQRRO6F6WdpH1R0vGibVhaclGDdiwAUCXAUMvxcccC56YWJlbEBw
ZW5ndXRyb25peC5kZQAKCRDVhaclGDdiwC+6AP4nFG1Kxyd7qjGxmR1nr03PWtFl
2ujIJO/x8kQooeJeMwD7BCQtO5gmcHgNrbOLLjitZ8OY891SXckORsIlgQcPnwE=
=mfJN
-----END PGP SIGNATURE-----
Merge tag 'imx-drm-next-2018-12-03' of git://git.pengutronix.de/git/pza/linux into drm-next
drm/imx: update image-convert with fixes for multi-tiled scaling
Update the ipu-v3 mem2mem image-convert code, with some fixes for race
conditions, alignment issues, and visual artifacts due to tile alignment
and scaling factor issues when scaling images larger than hardware
limitations in multiple tiles. This will allow the V4L2 mem2mem scaler
driver to write output images larger than 1024x1024 pixels.
Also switch drm/imx source files to SPDX license identifiers, constify
struct clk_ops in imx-tve, and add a timeout warning to the busy wait in
ipu_plane_disable().
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1543835266.5647.1.camel@pengutronix.de
Or Gerlitz says:
====================
net/sched: act_tunnel_key: support key-less tunnels
This short series from Adi Nissim allows to support key-less tunnels
by the tc tunnel key actions, which is needed for some GRE use-cases.
changes from V0:
- addresses build warning spotted by kbuild, make sure to always init
to zero the tunnel key
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It's possible to set a tunnel without a destination port. However,
on dump(), a zero dst port is returned to user space even if it was not
set, fix that.
Note that so far it wasn't required, b/c key less tunnels were not
supported and the UDP tunnels do require destination port.
Signed-off-by: Adi Nissim <adin@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow setting a tunnel without a tunnel key. This is required for
tunneling protocols, such as GRE, that define the key as an optional
field.
Signed-off-by: Adi Nissim <adin@mellanox.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8c0e64ac40 ("thermal: armada: get rid of the ->is_valid()
pointer") removed the unnecessary indirection through a function
pointer, but in doing so, also removed the negation operator too:
- if (priv->data->is_valid && !priv->data->is_valid(priv)) {
+ if (armada_is_valid(priv)) {
which results in:
armada_thermal f06f808c.thermal: Temperature sensor reading not valid
armada_thermal f2400078.thermal: Temperature sensor reading not valid
armada_thermal f4400078.thermal: Temperature sensor reading not valid
at boot, or whenever the "temp" sysfs file is read. Replace the
negation operator.
Fixes: 8c0e64ac40 ("thermal: armada: get rid of the ->is_valid() pointer")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
After getting a reference to the platform device's of_node the probe
function ends up calling of_find_matching_node() using the node as an
argument. The function takes care of decreasing the refcount on it. We
are then incorrectly decreasing the refcount on that node again.
This patch removes the unwarranted call to of_node_put().
Fixes: 414fd46e77 ("fsl/fman: Add FMan support")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in a DP_NOTICE message, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Wifi chip should be clocked by a 32kHz clock coming from i.MX7D
CLKO2 output pin, so describe the pinmux and clock hierarchy in the
device tree to allow the Wifi chip to be properly clocked.
Managed to successfully test Wifi with such change. Used the standard
nvram.txt file provided by TechNexion, which selects an external 32kHz
clock for the Wifi chip by default.
Fixes: 99a52450c7 ("ARM: dts: imx7d-pico: Add Wifi support")
Suggested-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Tested-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
If we attempt a direct issue to a SCSI device, and it returns BUSY, then
we queue the request up normally. However, the SCSI layer may have
already setup SG tables etc for this particular command. If we later
merge with this request, then the old tables are no longer valid. Once
we issue the IO, we only read/write the original part of the request,
not the new state of it.
This causes data corruption, and is most often noticed with the file
system complaining about the just read data being invalid:
[ 235.934465] EXT4-fs error (device sda1): ext4_iget:4831: inode #7142: comm dpkg-query: bad extra_isize 24937 (inode size 256)
because most of it is garbage...
This doesn't happen from the normal issue path, as we will simply defer
the request to the hardware queue dispatch list if we fail. Once it's on
the dispatch list, we never merge with it.
Fix this from the direct issue path by flagging the request as
REQ_NOMERGE so we don't change the size of it before issue.
See also:
https://bugzilla.kernel.org/show_bug.cgi?id=201685
Tested-by: Guenter Roeck <linux@roeck-us.net>
Fixes: 6ce3dd6eec ("blk-mq: issue directly if hw queue isn't busy in case of 'none'")
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move modify tirs hash functionality (mlx5e_modify_tirs_hash) from
en_ethtool.c to en_main.c. This allows future use of this fuctionality
from en_fs_ethtool.c, while keeping current convention: en_ethtool.c
doesn't have an API. There is no functional change here.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Remove couple of defines that are no longer used.
Signed-off-by: Gal Pressman <pressmangal@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
tx_pause_storm_warning_events ethtool counter name has a trailing
space, remove it.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
As the man(2) page for utime/utimes states, EPERM is returned when the
second parameter of utime or utimes is not NULL, the caller's effective UID
does not match the owner of the file, and the caller is not privileged.
However, in a NFS directory mounted from knfsd, it will return EACCES
(from nfsd_setattr-> fh_verify->nfsd_permission). This patch fixes
that.
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Add the clock input of the main clock controller
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the clock inputs of amlogic AO clock controller
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The GPCv2 on the Freescale i.MX8MQ SoC works in the same way as the
GPCv2 on the i.MX7, but only controls more power domains with a
different mapping.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The valid register ranges are defined by the implemented power domains,
which are different between the individual SoCs where the GPCv2 is used.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
So we can add i.MX8M support without introducing name clashes.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The values are taken from Amlogic's 3.10 kernel sources.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The values are taken from Amlogic's 3.10 kernel sources. Their sources
have a "meson8m2_n200_2G.dtd" which defines a different voltage table:
- 0.86V for 96MHz
- (values in between omitted)
- 1.14V for 1.992GHz
The reason for this is simply the hardware design because the voltage
regulator on this board is has a minimum output of 0.86V and a maximum
output of 1.14V. The recommended settings are added with this patch
instead of using the values that are only valid for one board.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Meson8b SoC is using four Cortex-A5 cores. These come with an ARM
global timer.
This adds the Cortex-A5 global timer but keeps it disabled for now. The
timer is clocked by the "PERIPH" clock whose rate can change during
runtime (when changing the frequency of the CPU clock). Unfortunately
the arm_global_timer driver does not handle changes to the clock rate
yet.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Meson8B SoC is using four ARM Cortex-A5 cores which come with a
"TWD" (Timer-Watchdog) based timer. This adds support for the ARM TWD
Timer on this SoC.
Suggested-by: Carlo Caione <carlo@endlessm.com>
[ rebased patch from Carlo, use IRQ_TYPE_EDGE_RISING instead of
IRQ_TYPE_LEVEL_LOW to prevent "GIC: PPI13 is secure or misconfigured"
message during boot, use pre-processor macros to specify the IRQ,
added the correct clock, dropped TWD watchdog node since there's no
driver for it anymore ]
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Meson8 and Meson8m2 SoCs are using four Cortex-A9 cores. These come
with an ARM global timer.
This adds the Cortex-A9 global timer but keeps it disabled for now. The
timer is clocked by the "PERIPH" clock whose rate can change during
runtime (when changing the frequency of the CPU clock). Unfortunately
the arm_global_timer driver does not handle changes to the clock rate
yet.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Meson8 and Meson8m2 SoC are using four ARM Cortex-A9 cores which
come with a "TWD" (Timer-Watchdog) based timer. This adds support for
the ARM TWD Timer on these two SoCs.
Suggested-by: Carlo Caione <carlo@endlessm.com>
[ rebased patch from Carlo, use IRQ_TYPE_EDGE_RISING instead of
IRQ_TYPE_LEVEL_LOW to prevent "GIC: PPI13 is secure or misconfigured"
message during boot, use pre-processor macros to specify the IRQ,
added the correct clock, dropped TWD watchdog node since there's no
driver for it anymore ]
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The public Meson8b (S805) datasheet describes a memory region called "A9
Periph base" which starts at 0xC4300000 and ends at 0xC430FFFF. Add a
simple-bus node and move all peripherals that are part of this memory
region.
This makes the .dts a bit easier to read. No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Select CONFIG_TOUCHSCREEN_GOODIX so that we can have functional touch
screen by default on Digi International's AUO/Goodix LCD accessory kit used
with the ConnectCore 6UL SBC Pro (ccimx6ulsbcpro) board.
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- Export Meson8b CPU post dividers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJb+AtSAAoJEHfc29rIyEnRIR8QALMwOEecdl6B8VOjfaa4dwXE
wBOyKegDtXU3sYfdol1tpcNH/6R0z+fKIrs4F85hR9LmH+EKNW8RQuHs5wGJKkOJ
6/hFzU+6wVlKLy+OoMNCvWyPJe0C29wrtsNwlFz4Rdna70cSQL67tXDtA5FG2JZ0
fD0kOZvvU/XPbbS7Q9nPsf/WLKvYnXINGAfwb28+t+kMTu8XS6aiifUiT88eHi+u
LyRRnqX5rNZW8JITyVjDFMtM4Wnpq0H0D0c0j/ogCuOZRbvbgpTPKqW4XjMSIruZ
/7S73Alx8eCoA/RtUAWDj3P0CAwH+QbBa/zgcHGNhA1gSsVa+EkyRVqkGWpEeQ4c
6oKbYs5zl0R+J1rSyObuw3GchNiRbtXlftPdj2jQZ0Nf2V659JUfXtqcJQuU2NAb
pg3Gjo7tzTYHJkxi+zcYWjtVKFEi6Mm4zl1lGvfpBrGW3jk1OZ5PXYKgVdqS8LF2
vpgc0L45PiFuF9a7WTWwUVhxvR0kmbOMyBBS6iRGoqjEvuIGKAvosdYtK1nQvwua
21I0Rl6KSg2H2Gw6qR9txFLclwYM27i/EohtmpEEwSZGo+3CtO6TvPvkE+kykeKh
t2WR9kSmltEAd0VFkvj/c7sTiIiradZLf8HTVZ9q7PP5In2JlQLUTdSL8tuISEvN
ndJAFo4l2oEoHpKB2xu0
=Y5Z4
-----END PGP SIGNATURE-----
Merge tag 'meson-clk-headers-4.21-1' of git://github.com/BayLibre/clk-meson into v4.21/dt
Update for meson clocks bindings targeted at v4.21:
- Export Meson8b CPU post dividers
* tag 'meson-clk-headers-4.21-1' of git://github.com/BayLibre/clk-meson:
dt-bindings: clock: meson8b: export the CPU post dividers
Kevin is basically doing all the work. Remove my name as co-maintainer.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
There is actually no alternate xtal on any of the axg board I have
seen so far. The 32k is actually generated internally, deriving from
the 24MHz main xtal.
Amlogic SoC also have the option to provide the 32k reference externally,
through one of the AO pads, but no platform is using this ATM.
Fixes: 5e395e1466 ("ARM64: dts: meson-axg: add an 32K alt aoclk")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the watchdog node also on the AXG platforms.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Instead of passing GPIO numbers directly to the PalmLD
ATA driver, pass GPIO descriptors from the board file and
handle these in the driver.
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pass a GPIO descriptor for the device instead of a hardcoded
GPIO number from the global GPIO numberspace. Use gpio
descriptors throughout.
Cut the now completely unused platform data for the CF slot.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Waldemar Brodkorb <wbx@openadk.org>
Cc: Matt Redfearn <matt.redfearn@mips.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This pure device tree driver is simple to convert to use
just GPIO descriptors instead of GPIO numbers. So let's
just do it.
Cc: Mark Langsdorf <mlangsdo@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This driver does not use GPIO or anything from the GPIO header.
Drop the include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Rename SPI controller node in the XTFPGA DTS to spi@...
This fixes the following build warnings:
arch/xtensa/boot/dts/kc705_nommu.dtb: Warning (spi_bus_bridge):
/soc/spi-master@0d0a0000: node name for SPI buses should be 'spi'
arch/xtensa/boot/dts/kc705_nommu.dtb: Warning (spi_bus_reg):
Failed prerequisite 'spi_bus_bridge'
arch/xtensa/boot/dts/lx200mx.dtb: Warning (spi_bus_bridge):
/soc/spi-master@0d0a0000: node name for SPI buses should be 'spi'
arch/xtensa/boot/dts/lx200mx.dtb: Warning (spi_bus_reg):
Failed prerequisite 'spi_bus_bridge'
arch/xtensa/boot/dts/kc705.dtb: Warning (spi_bus_bridge):
/soc/spi-master@0d0a0000: node name for SPI buses should be 'spi'
arch/xtensa/boot/dts/kc705.dtb: Warning (spi_bus_reg):
Failed prerequisite 'spi_bus_bridge'
arch/xtensa/boot/dts/ml605.dtb: Warning (spi_bus_bridge):
/soc/spi-master@0d0a0000: node name for SPI buses should be 'spi'
arch/xtensa/boot/dts/ml605.dtb: Warning (spi_bus_reg):
Failed prerequisite 'spi_bus_bridge'
arch/xtensa/boot/dts/lx60.dtb: Warning (spi_bus_bridge):
/soc/spi-master@0d0a0000: node name for SPI buses should be 'spi'
arch/xtensa/boot/dts/lx60.dtb: Warning (spi_bus_reg):
Failed prerequisite 'spi_bus_bridge'
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
For most OCTEON SoCs there is a repeated and redundant register definition
for almost every hardware register, although the register bit fields
would not differ from other SoCs. Since the driver code should use only
one definition for simplicity, these other fields are just redundant
and can be deleted.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Chips up to cn5xxx are compatible with cn38xx. All cn6xxx chips, and also
cnf71xx, are compatible with cn61xx.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
cn58xx is compatible with cn50xx, so use the latter.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
[paul.burton@mips.com: s/cn52xx/cn50xx/ in commit message.]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
cvmx_gpio_bit_cfgx bitfields are indentical on cn70xx and cn73xx,
and also match the default definition. So use that instead.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org