Some users of rhashtables might need to move an object from one table
to another - this appears to be the reason for the incomplete usage
of NULLS markers.
To support these, we store a unique NULLS_MARKER at the end of
each chain, and when a search fails to find a match, we check
if the NULLS marker found was the expected one. If not, the search
may not have examined all objects in the target bucket, so it is
repeated.
The unique NULLS_MARKER is derived from the address of the
head of the chain. As this cannot be derived at load-time the
static rhnull in rht_bucket_nested() needs to be initialised
at run time.
Any caller of a lookup function must still be prepared for the
possibility that the object returned is in a different table - it
might have been there for some time.
Note that this does NOT provide support for other uses of
NULLS_MARKERs such as allocating with SLAB_TYPESAFE_BY_RCU or changing
the key of an object and re-inserting it in the same table.
These could only be done safely if new objects were inserted
at the *start* of a hash chain, and that is not currently the case.
Signed-off-by: NeilBrown <neilb@suse.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Salil Mehta says:
====================
Adds VF/PF PCIe reg dump(ethtool -d) support to HNS3 driver
This patchset adds VF/PF PCIe register dump support to HNS3 VF and PF
driver using "ethtool -d" command.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to dump PF PCIe registers using ethtool -d
for HNS3 PF Driver.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds "ethtool -d" support for HNS3 VF Driver.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yoshihiro Shimoda says:
====================
net: phy: micrel: add toggling phy reset
This patch set is for R-Car Gen3 Salvator-XS boards. If we do
the following method, the phy cannot link up correctly.
1) Kernel boots by using initramfs.
--> No open the nic, so phy_device_register() and phy_probe()
deasserts the reset.
2) Kernel enters the suspend.
--> So, keep the reset signal as deassert.
--> On R-Car Salvator-XS board, unfortunately, the board power is
turned off.
3) Kernel returns from suspend.
4) ifconfig eth0 up
--> Then, since edge signal of the reset doesn't happen,
it cannot link up.
5) ifconfig eth0 down
6) ifconfig eth0 up
--> In this case, it can link up.
When resolving this issue after I got feedback from Andrew and Heiner,
I found an issue that the phy_device.c didn't call phy_resume()
if the PHY was not attached. So, patch 1 fixes it and add toggling
the phy reset to the micrel phy driver.
Changes from v1 (as RFC):
- No remove the current code of phy_device.c to avoid any side effects.
- Fix the mdio_bus_phy_resume() in phy_device.c.
- Add toggling the phy reset in micrel.c if the PHY is not attached.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds toggling phy reset if PHY is not attached. Otherwise,
some boards (e.g. R-Car H3 Salvator-XS) cannot link up correctly if
we do the following method:
1) Kernel boots by using initramfs.
--> No open the nic, so phy_device_register() and phy_probe()
deasserts the reset.
2) Kernel enters the suspend.
--> So, keep the reset signal as deassert.
--> On R-Car Salvator-XS board, unfortunately, the board power is
turned off.
3) Kernel returns from suspend.
4) ifconfig eth0 up
--> Then, since edge signal of the reset doesn't happen,
it cannot link up.
5) ifconfig eth0 down
6) ifconfig eth0 up
--> In this case, it can link up.
Reported-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an issue that mdio_bus_phy_resume() doesn't call
phy_resume() if the PHY is not attached.
Fixes: 803dd9c77a ("net: phy: avoid suspending twice a PHY")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far the two functions consider neither member eee_enabled nor
eee_active. Therefore network drivers have to do this in some kind
of glue code. I think this can be avoided.
Getting EEE parameters:
When not advertising any EEE mode, we can't consider EEE to be enabled.
Therefore interpret "EEE enabled" as "we advertise at least one EEE
mode". It's similar with "EEE active": interpret it as "EEE modes
advertised by both link partner have at least one mode in common".
Setting EEE parameters:
If eee_enabled isn't set, don't advertise any EEE mode and restart
aneg if needed to switch off EEE. If eee_enabled is set and
data->advertised is empty (e.g. because EEE was disabled), advertise
everything we support as default. This way EEE can easily switched
on/off by doing ethtool --set-eee <if> eee on/off, w/o any additional
parameters.
The changes to both functions shouldn't break any existing user.
Once the changes have been applied, at least some users can be
simplified.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When NULL pointer accidentally passed to write_kprobe_events,
due to strlen(NULL), segmentation fault happens.
Changed code returns -1 to deal with this situation.
Bug issued with Smatch, static analysis.
Signed-off-by: Daniel T. Lee <danieltimlee@gmail.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This helps separate what capabilities are display capabilities.
v3: Moving display struct right after flags (Lucas)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Suggested-by: Jani Nikula <jani.nikula@linux.intel.com>
Suggested-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181130232048.14216-2-jose.souza@intel.com
Right now it is decided if GEN has display by checking the num_pipes,
so lets make it explicit and use a macro.
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181130232048.14216-1-jose.souza@intel.com
Enric has volunteered to help me with maintaining chrome-platform
as we change the development model toward strictly upstream-first for
any chrome-platform and cros_ec driver.
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Once the JITed images for each function in a multi-function program
are generated after the first three JIT passes, we only need to fix
the target address for the branch instruction corresponding to each
bpf-to-bpf function call.
This introduces the following optimizations for reducing the work
done by the JIT compiler when handling multi-function programs:
[1] Instead of doing two extra passes to fix the bpf function calls,
do just one as that would be sufficient.
[2] During the extra pass, only overwrite the instruction sequences
for the bpf-to-bpf function calls as everything else would still
remain exactly the same. This also reduces the number of writes
to the JITed image.
[3] Do not regenerate the prologue and the epilogue during the extra
pass as that would be redundant.
Signed-off-by: Sandipan Das <sandipan@linux.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Benson has been maintaining this together with the rest of the kernel
team for a while now, so remove myself from the entry.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Benson Leung <bleung@chromium.org>
Alexis Bauvin says:
====================
net: Add VRF support for VXLAN underlay
v6 -> v7:
- proper locking for device in udp_tunnel following Sabrina Dubroca's advice
v5 -> v6:
- remove automatic rebinding patch following Roopa Prabhu's advice
v4 -> v5:
- move test script to its own patch (6/6)
- add schematic for test script
- apply David Ahern comments to the test script
v3 -> v4:
- rename vxlan_is_in_l3mdev_chain to netdev_is_upper master
- move it to net/core/dev.c
- make it return bool instead of int
- check if remote_ifindex is zero before resolving the l3mdev
- add testing script
v2 -> v3:
- fix build when CONFIG_NET_IPV6 is off
- fix build "unused l3mdev_master_upper_ifindex_by_index" build error with some
configs
v1 -> v2:
- move vxlan_get_l3mdev from vxlan driver to l3mdev driver as
l3mdev_master_upper_ifindex_by_index
- vxlan: rename variables named l3mdev_ifindex to ifindex
v0 -> v1:
- fix typos
We are trying to isolate the VXLAN traffic from different VMs with VRF as shown
in the schemas below:
+-------------------------+ +----------------------------+
| +----------+ | | +------------+ |
| | | | | | | |
| | tap-red | | | | tap-blue | |
| | | | | | | |
| +----+-----+ | | +-----+------+ |
| | | | | |
| | | | | |
| +----+---+ | | +----+----+ |
| | | | | | | |
| | br-red | | | | br-blue | |
| | | | | | | |
| +----+---+ | | +----+----+ |
| | | | | |
| | | | | |
| | | | | |
| +----+--------+ | | +--------------+ |
| | | | | | | |
| | vxlan-red | | | | vxlan-blue | |
| | | | | | | |
| +------+------+ | | +-------+------+ |
| | | | | |
| | VRF | | | VRF |
| | red | | | blue |
+-------------------------+ +----------------------------+
| |
| |
+---------------------------------------------------------+
| | | |
| | | |
| | +--------------+ | |
| | | | | |
| +---------+ eth0.2030 +---------+ |
| | 10.0.0.1/24 | |
| +-----+--------+ VRF |
| | green|
+---------------------------------------------------------+
|
|
+----+---+
| |
| eth0 |
| |
+--------+
iproute2 commands to reproduce the setup:
ip link add green type vrf table 1
ip link set green up
ip link add eth0.2030 link eth0 type vlan id 2030
ip link set eth0.2030 master green
ip addr add 10.0.0.1/24 dev eth0.2030
ip link set eth0.2030 up
ip link add blue type vrf table 2
ip link set blue up
ip link add br-blue type bridge
ip link set br-blue master blue
ip link set br-blue up
ip link add vxlan-blue type vxlan id 2 local 10.0.0.1 dev eth0.2030 \
port 4789
ip link set vxlan-blue master br-blue
ip link set vxlan-blue up
ip link set tap-blue master br-blue
ip link set tap-blue up
ip link add red type vrf table 3
ip link set red up
ip link add br-red type bridge
ip link set br-red master red
ip link set br-red up
ip link add vxlan-red type vxlan id 3 local 10.0.0.1 dev eth0.2030 \
port 4789
ip link set vxlan-red master br-red
ip link set vxlan-red up
ip link set tap-red master br-red
ip link set tap-red up
We faced some issue in the datapath, here are the details:
* Egress traffic:
The vxlan packets are sent directly to the default VRF because it's where the
socket is bound, therefore the traffic has a default route via eth0. the
workaround is to force this traffic to VRF green with ip rules.
* Ingress traffic:
When receiving the traffic on eth0.2030 the vxlan socket is unreachable from
VRF green. The workaround is to enable *udp_l3mdev_accept* sysctl, but
this breaks isolation between overlay and underlay: packets sent from
blue or red by e.g. a guest VM will be accepted by the socket, allowing
injection of VXLAN packets from the overlay.
This patch series fixes the issues describe above by allowing VXLAN socket to be
bound to a specific VRF device therefore looking up in the correct table.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This script tests the support of a VXLAN underlay in a non-default VRF.
It does so by simulating two hypervisors and two VMs, an extended L2
between the VMs with the hypervisors as VTEPs with the underlay in a
VRF, and finally by pinging the two VMs.
It also tests that moving the underlay from a VRF to another works when
down/up the VXLAN interface.
Signed-off-by: Alexis Bauvin <abauvin@scaleway.com>
Reviewed-by: Amine Kherbouche <akherbouche@scaleway.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: Amine Kherbouche <akherbouche@scaleway.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a node for the Camera Subsystem present on the Qualcomm
MSM8996 SoC.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Creating a VXLAN device with is underlay in the non-default VRF makes
egress route lookup fail or incorrect since it will resolve in the
default VRF, and ingress fail because the socket listens in the default
VRF.
This patch binds the underlying UDP tunnel socket to the l3mdev of the
lower device of the VXLAN device. This will listen in the proper VRF and
output traffic from said l3mdev, matching l3mdev routing rules and
looking up the correct routing table.
When the VXLAN device does not have a lower device, or the lower device
is in the default VRF, the socket will not be bound to any interface,
keeping the previous behaviour.
The underlay l3mdev is deduced from the VXLAN lower device
(IFLA_VXLAN_LINK).
+----------+ +---------+
| | | |
| vrf-blue | | vrf-red |
| | | |
+----+-----+ +----+----+
| |
| |
+----+-----+ +----+----+
| | | |
| br-blue | | br-red |
| | | |
+----+-----+ +---+-+---+
| | |
| +-----+ +-----+
| | |
+----+-----+ +------+----+ +----+----+
| | lower device | | | |
| eth0 | <- - - - - - - | vxlan-red | | tap-red | (... more taps)
| | | | | |
+----------+ +-----------+ +---------+
Signed-off-by: Alexis Bauvin <abauvin@scaleway.com>
Reviewed-by: Amine Kherbouche <akherbouche@scaleway.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: Amine Kherbouche <akherbouche@scaleway.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Existing functions to retreive the l3mdev of a device did not walk the
master chain to find the upper master. This patch adds a function to
find the l3mdev, even indirect through e.g. a bridge:
+----------+
| |
| vrf-blue |
| |
+----+-----+
|
|
+----+-----+
| |
| br-blue |
| |
+----+-----+
|
|
+----+-----+
| |
| eth0 |
| |
+----------+
This will properly resolve the l3mdev of eth0 to vrf-blue.
Signed-off-by: Alexis Bauvin <abauvin@scaleway.com>
Reviewed-by: Amine Kherbouche <akherbouche@scaleway.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: Amine Kherbouche <akherbouche@scaleway.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP tunnel sockets are always opened unbound to a specific device. This
patch allow the socket to be bound on a custom device, which
incidentally makes UDP tunnels VRF-aware if binding to an l3mdev.
Signed-off-by: Alexis Bauvin <abauvin@scaleway.com>
Reviewed-by: Amine Kherbouche <akherbouche@scaleway.com>
Tested-by: Amine Kherbouche <akherbouche@scaleway.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add pinctrls required for camera sensors:
- power down signal;
- reset signal;
- camera external clock.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add pinctrls required for Camera Control Interface.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add a node for the Camera Subsystem present on the Qualcomm
MSM8916 SoC.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.
Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.
Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
We only need the request fields and the end_io time if we have
stats enabled, or if we have a scheduler attached as those may
use it for completion time stats.
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Ido Schimmel says:
====================
mlxsw: Add 'fw_load_policy' devlink parameter
Shalom says:
Currently, drivers do not have the ability to control the firmware
loading policy and they always use their own fixed policy. This prevents
drivers from running the device with a different firmware version for
testing and/or debugging purposes. For example, testing a firmware bug
fix.
For these situations, the new devlink generic parameter,
'fw_load_policy', gives the ability to control this option and allows
drivers to run with a different firmware version than required by the
driver.
Patch #1 adds the new parameter to devlink. The other two patches, #2
and #3, add support for this parameter in the mlxsw driver.
Example:
# Query the devlink parameters supported by the device
$ devlink dev param show
pci/0000:03:00.0:
name fw_load_policy type generic
values:
cmode driverinit value driver
# Flash new firmware using ethtool
$ ethtool -f swp1 mellanox/mlxsw_spectrum-13.1703.4.mfa2
# Toggle parameter
$ devlink dev param set pci/0000:03:00.0 name fw_load_policy value flash cmode driverinit
# devlink reset
$ devlink dev reload pci/0000:03:00.0
# Query firmware version to show changes took affect
$ ethtool -i swp1
driver: mlxsw_spectrum
version: 1.0
firmware-version: 13.1703.4
expansion-rom-version:
bus-info: 0000:03:00.0
supports-statistics: yes
supports-test: no
supports-eeprom-access: no
supports-register-dump: no
supports-priv-flags: no
iproute2 patches available here:
https://github.com/tshalom/iproute2-next
v2:
* Change 'fw_version_check' to 'fw_load_policy' with values 'driver' and
'flash' (Jakub)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Load firmware version based on 'fw_load_policy' devlink parameter. The
driver supports these two options:
* DEVLINK_PARAM_FW_LOAD_POLICY_VALUE_DRIVER (0)
Default, load firmware version preferred by the driver
* DEVLINK_PARAM_FW_LOAD_POLICY_VALUE_FLASH (1)
Load firmware currently stored in flash
The second option, 'flash', allow the device to run with different firmware
version than preferred by the driver for testing and/or debugging purposes.
For example, testing a firmware bug fix.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After flashing new firmware during the driver initialization flow (reload
or not), the driver should do a firmware reset when it gets -EAGAIN in
order to load the new one.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many drivers load the device's firmware image during the initialization
flow either from the flash or from the disk. Currently this option is not
controlled by the user and the driver decides from where to load the
firmware image.
'fw_load_policy' gives the ability to control this option which allows the
user to choose between different loading policies supported by the driver.
This parameter can be useful while testing and/or debugging the device. For
example, testing a firmware bug fix.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are missing 'static' so sparse complains:
drivers/clk/meson/vid-pll-div.c:58:26: warning: symbol '_get_table_val' was not declared. Should it be static?
drivers/clk/meson/gxbb.c:1585:12: warning: symbol 'gxbb_vid_pll_parent_names' was not declared. Should it be static?
drivers/clk/meson/gxbb.c:1620:12: warning: symbol 'gxbb_vclk_parent_names' was not declared. Should it be static?
drivers/clk/meson/gxbb.c:1980:12: warning: symbol 'gxbb_cts_parent_names' was not declared. Should it be static?
drivers/clk/meson/gxbb.c:2036:12: warning: symbol 'gxbb_cts_hdmi_tx_parent_names' was not declared. Should it be static?
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Since any page fault may be interrupted by a MMU invalidation and implicit
leaf MR may be released during this process. The check for parent value
is unreliable condition for an implicit MR.
Use other condition that we can rely on to determine if MR is implicit.
Fixes: b4cfe447d4 ("IB/mlx5: Implement on demand paging by adding support for MMU notifiers")
Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch adds a set of DTS files that support all PXA3xx based Raumfeld
audio hardware devices.
Common nodes are factored out into 'common' and 'tuneable-clock' include
files to keep the top-level DTS files smaller.
Signed-off-by: Daniel Mack <daniel@zonque.org>
[Robert: Reordered Makefile in alphabetical order]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Currently __set_phy_supported allows to add modes w/o checking whether
the PHY supports them. This is wrong, it should never add modes but
only remove modes we don't want to support.
The commit marked as fixed didn't do anything wrong, it just copied
existing functionality to the helper which is being fixed now.
Fixes: f3a6bd393c ("phylib: Add phy_set_max_speed helper")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently __set_phy_supported allows to add modes w/o checking whether
the PHY supports them. This is wrong, it should never add modes but
only remove modes we don't want to support.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a plan to build the kernel with -Wimplicit-fallthrough and
these places in the code produced warnings. Fix them up.
This patch produces no change in behaviour, but should be reviewed in
case these are actually bugs not intentional fallthoughs.
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Kees Cook <keescook@google.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
As the pxa architecture and all its related drivers do not rely anymore
on the filter function, thanks to the slave map conversion, make
pxad_filter_fn() static, and remove it from the global namespace.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Vinod Koul <vkoul@kernel.org>
The warning added in commit 3b0e761ba8
"dlm: print log message when cluster name is not set"
did not account for the fact that lockspaces created
from userland do not supply a cluster name, so bogus
warnings are printed every time a userland lockspace
is created.
Signed-off-by: David Teigland <teigland@redhat.com>
* Fix llcc license, includes, and error checks
* Remove use of memcpy in cmd-db and fix API breakage
* Add QCS404 compatible to SMD-RPM
* Minor fixes for QMI
* Add irq clear handling in QCOM Geni SE during init
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=hySS
-----END PGP SIGNATURE-----
Merge tag 'qcom-drivers-for-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/drivers
Qualcomm ARM Based Driver Updates for v4.21
* Fix llcc license, includes, and error checks
* Remove use of memcpy in cmd-db and fix API breakage
* Add QCS404 compatible to SMD-RPM
* Minor fixes for QMI
* Add irq clear handling in QCOM Geni SE during init
* tag 'qcom-drivers-for-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
drm: msm: Check cmd_db_read_aux_data() for failure
soc: qcom: smd-rpm: Add QCS404 compatible
soc: qcom: llcc-slice: Remove duplicated include from llcc-slice.c
soc: qcom: cmd-db: Stop memcpy()ing in cmd_db_read_aux_data()
soc: qcom: cmd-db: Remove memcpy()ing from cmd_db_get_header()
soc: qcom: Drop help text for QCOM_QMI_HELPERS
soc: qcom: qmi_interface: Limit txn ids to U16_MAX
soc: qcom: llcc-slice: Add error checks for API functions
soc: qcom/llcc: add MODULE_LICENSE tag
soc: qcom: Add irq clear handling during SE init
Signed-off-by: Olof Johansson <olof@lixom.net>
for 4.21, please pull the following:
- Stefan switches relevant BCM283x files under arch/arm/mach-bcm to the
SPDX license identifiers
- Justin adds an entry in the Broadcom STB debug LL stub for 7255
- Florian enables reset controller support for BCM63xx SoCs
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEm+Rq3+YGJdiR9yuFh9CWnEQHBwQFAlwC0vMACgkQh9CWnEQH
BwRjrQ//ZWip8GnZBcZNoov5M1KxSEkcpMvfM6VhplP3ZCftkxZ0FaTq82DvOG3v
hiCE9iF9x77bsk/l0U1qU9SIJ7cVTtdNoZVeY7rtw2PaSRF1ZiiNY36fH8gM/ebY
HftefXkVnnOmXmTK6C3Rt2AH1QPdCh1SrG/wp11n79FSC8ySSz0JXnvPa8hxJcyt
Y9Wm5gwKYDl06VB5CVkjmyUcf4nIG5cqwYkVAGSM76/zIBB4nV4KhOHJo9M5RQvV
IFxzYrTLCRZjutV8bKnl5V1IIwB1zPpr9hqxpdP8rwai2jEDG3LlJY+BPqT0vwM3
RPUOOvpjQbICTpJ22353P2dQm2lKc304MzIljvYriCoY/hItELC57qxrHbKLn/yX
k+/Ni+FdJfyjdxK2Ljl83+IgwrVc/QRDUVx55PP3QgaxMAKFmcj0xcIRWdlprKfI
Q85rBTLiMhRESgICpZmMdZ3ZKgioPxC/n+/atPHPkQNlMofH/2R8mz6YBjCnuQ29
MuNpgEEgv2Pvqh2OxUzZ77fsZxpA6Anwu7+jfu9v7rdI+3YZI5jZSdthwbphdd1D
qJJVs3cU/U/b7nFq5aRI7x49ToYB5eszORDbmlK3lkkMsK7aQq2MlTW1cwpfckay
LM/YhCGd02XyU+YZlIJChtV/YSoMvPlVNBPfPieTGkccKUu4mbY=
=zL87
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.21/soc' of https://github.com/Broadcom/stblinux into next/soc
This pull request contains Broadcom ARM-based SoCs machine files updates
for 4.21, please pull the following:
- Stefan switches relevant BCM283x files under arch/arm/mach-bcm to the
SPDX license identifiers
- Justin adds an entry in the Broadcom STB debug LL stub for 7255
- Florian enables reset controller support for BCM63xx SoCs
* tag 'arm-soc/for-4.21/soc' of https://github.com/Broadcom/stblinux:
ARM: mach-bcm: Switch bcm2835 and platsmp to SPDX identifier
ARM: BCM63XX: Enable reset controller support
ARM: brcmstb: Add entry for 7255
Signed-off-by: Olof Johansson <olof@lixom.net>
for 4.21, please pull the following changes:
- James fixes the firmware interface after a commit changed the use of
VLA and broke large transfers
- Stefan adds a timeout check for Raspberry Pi firmware transactions and
updates a bunch of SoC/firmware files to use SPDX tags
- Wolfram switches the GISB bus arbiter to use dev_get_drvdata()
- Yangtao provides a fix for a reference leak due to a call to
of_find_node_by_path()
- Florian fixes the CPU re-entry point out of S3 suspend with kernels
built in Thumb2 mode
-----BEGIN PGP SIGNATURE-----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=yGiB
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.21/drivers' of https://github.com/Broadcom/stblinux into next/drivers
This pull request contains Broadcom ARM/ARM64/MIPS SoCs drivers changes
for 4.21, please pull the following changes:
- James fixes the firmware interface after a commit changed the use of
VLA and broke large transfers
- Stefan adds a timeout check for Raspberry Pi firmware transactions and
updates a bunch of SoC/firmware files to use SPDX tags
- Wolfram switches the GISB bus arbiter to use dev_get_drvdata()
- Yangtao provides a fix for a reference leak due to a call to
of_find_node_by_path()
- Florian fixes the CPU re-entry point out of S3 suspend with kernels
built in Thumb2 mode
* tag 'arm-soc/for-4.21/drivers' of https://github.com/Broadcom/stblinux:
soc: bcm: brcmstb: Don't leak device tree node reference
firmware: raspberrypi: Switch to SPDX identifier
firmware: raspberrypi: Fix firmware calls with large buffers
soc: bcm: Switch raspberrypi-power to SPDX identifier
firmware: raspberrypi: Define timeout for transactions
bus: brcmstb_gisb: simplify getting .driver_data
soc: bcm: brcmstb: Fix re-entry point with a THUMB2_KERNEL
Signed-off-by: Olof Johansson <olof@lixom.net>
please pull the following for 4.20:
- Stefan fixes the polariy of the Wi-Fi reset GPIOs signals which would
break on Raspberry Pi 3B and 3B+
-----BEGIN PGP SIGNATURE-----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=iFMZ
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.20/devicetree-fixes' of https://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes,
please pull the following for 4.20:
- Stefan fixes the polariy of the Wi-Fi reset GPIOs signals which would
break on Raspberry Pi 3B and 3B+
* tag 'arm-soc/for-4.20/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm2837: Fix polarity of wifi reset GPIOs
Signed-off-by: Olof Johansson <olof@lixom.net>
A recent performance enhancement introduced a latency issue in the
HFI message path. The new algorithm removed a forced call send for
PIO messages and added a forced schedule event for messages larger
than the MTU.
For PIO, the schedule path can introduce thrashing that can
significantly impact the throughput for small messages.
If a message size is within the PIO threshold, always take the send
path.
Fixes: 0b79b27748 ("IB/{hfi1, qib, rdmavt}: Schedule multi RC/UC packets instead of posting")
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>