Essentially this patch moves the TX mailbox to position 63, regardless
of timestamp based offloading or RX FIFO. So mainly the iflag register
usage regarding TX has changed. The rest is consolidating RX FIFO and
timestamp offloading as they now use both the same TX mailbox.
The reason is a very annoying behavior regarding sending RTR frames when
_not_ using RX FIFO:
If a TX mailbox sent a RTR frame it becomes a RX mailbox. For that
reason flexcan_irq disables the TX mailbox again. But if during the time
the RTR was sent and the TX mailbox is disabled a new CAN frames is
received, it is lost without notice. The reason is that so-called
"Move-in" process starts from the lowest mailbox which happen to be a TX
mailbox set to EMPTY.
Steps to reproduce (I used an imx7d):
1. generate regular bursts of messages
2. send a RTR from flexcan with higher priority than burst messages every
1ms, e.g. cangen -I 0x100 -L 0 -g 1 -R can0
3. notice a lost message without notification after some seconds
When running an iperf in parallel this problem is occurring even more
frequently. Using filters is not possible as at least one single CAN-ID
is allowed. Handling the TX MB during RX is also not possible as there
is no race-free disable of RX MB.
There is still a slight window when the described problem can occur. But
for that all RX MB must be in use which is essentially next to an
overrun. Still there will be no indication if it ever occurs.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Unlock the MB irrespective of reception method being FIFO or timestamp
based. It is optional but recommended to unlock Mailbox as soon as
possible and make it available for reception.
Reported-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If the hi3110 shares the SPI bus with another traffic-intensive device
and packets are received in high volume (by a separate machine sending
with "cangen -g 0 -i -x"), reception stops after a few minutes and the
counter in /proc/interrupts stops incrementing. Bus state is "active".
Bringing the interface down and back up reconvenes the reception. The
issue is not observed when the hi3110 is the sole device on the SPI bus.
Using a level-triggered interrupt makes the issue go away and lets the
hi3110 successfully receive 2 GByte over the course of 5 days while a
ks8851 Ethernet chip on the same SPI bus handles 6 GByte of traffic.
Unfortunately the hi3110 datasheet is mum on the trigger type. The pin
description on page 3 only specifies the polarity (active high):
http://www.holtic.com/documents/371-hi-3110_v-rev-kpdf.do
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Casey Fitzpatrick <casey.fitzpatrick@timesys.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Document RZ/G2M (r8a774a1) SoC specific bindings.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Assigning 2 to "renesas,can-clock-select" tricks the driver into
registering the CAN interface, even though we don't want that.
This patch improves one of the checks to prevent that from happening.
Fixes: 862e2b6af9 ("can: rcar_can: support all input clocks")
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Document the support for rcar_can on R8A77965 SoC devices.
Add R8A77965 to the list of SoCs which require the "assigned-clocks" and
"assigned-clock-rates" properties (thanks, Sergei).
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/can/usb/ucan.c: In function 'ucan_disconnect':
drivers/net/can/usb/ucan.c:1578:21: warning:
variable 'udev' set but not used [-Wunused-but-set-variable]
struct usb_device *udev;
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Martin Elshuber <martin.elshuber@theobroma-systems.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The call to can_put_echo_skb() may result in the skb being freed. The skb
is later used in the call to dev->ops->dev_frame_to_cmd().
This is avoided by moving the call to can_put_echo_skb() after
dev->ops->dev_frame_to_cmd().
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If alloc_can_err_skb() fails, cf is never initialized.
Move assignment of cf inside check.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When the socket is CAN FD enabled it can handle CAN FD frame
transmissions. Add an additional check in raw_sendmsg() as a CAN2.0 CAN
driver (non CAN FD) should never see a CAN FD frame. Due to the commonly
used can_dropped_invalid_skb() function the CAN 2.0 driver would drop
that CAN FD frame anyway - but with this patch the user gets a proper
-EINVAL return code.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
commit c0ea089dba ("ASoC: rsnd: rsnd_mod_name() handles both name and
ID") merged "name" and "ID" on rsnd_mod_name() to handle sub-ID
(= for CTU/BUSIF).
Then, it decided to share static char to avoid pointless memory.
But, it doesn't work correctry in below case, because last called
name will be used.
dev_xxx(dev, "%s is connected to %s\n",
rsnd_mod_name(mod_a), /* ssiu[00] */
rsnd_mod_name(mod_b)); /* ssi[0] */
->
rcar_sound ec500000.sound: ssi[0] is connected to ssi[0]
~~~~~~ ~~~~~~
We still don't want to have pointless memory, so let's use ring buffer.
16byte x 5 is very enough for this purpose.
dev_xxx(dev, "%s is connected to %s\n",
rsnd_mod_name(mod_a), /* ssiu[00] */
rsnd_mod_name(mod_b)); /* ssi[0] */
->
rcar_sound ec500000.sound: ssiu[00] is connected to ssi[0]
~~~~~~~~ ~~~~~~
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
IBX has a documented workaround which states that when we disable the
port we must change its transcoder select to A, otherwise it will
prevent the other port (DP vs. HDMI/SDVO) from using transcoder A.
We implement the workaround during encoder disable, but looks like
some BIOSen leave transcoder B selected even when the port wasn't
actually enabled by the BIOS. That will trip up our asserts
that attempt to make sure we never forget this w/a.
Sanitize the transcoder select to A for all disabled PCH
DP/HDMI/SDVO ports. We assume that the port was never enabled
by the BIOS on transcoder B, because if it had we'd actually have
to toggle the port on and back off to properly switch it back to
transcoder A. That would cause some display flicker if transcoder A
is already enabled on some other port, so it's better not to do it
unless absolutely necessary. Since we have no indication that the
transcoder select is misbehaving on the affected machines we can
assume the port was never actually enabled by the BIOS.
This cures warning like this during driver load:
IBX PCH DP C still using transcoder B
WARNING: CPU: 2 PID: 172 at drivers/gpu/drm/i915/intel_display.c:1279 assert_pch_dp_disabled+0x9e/0xb0 [i915]
v2: Add comments to remind the reader that SDVOB==HDMIB (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181108143635.9556-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
In my haste to remove irq_port[] I accidentally changed the
way we deal with hpd pins that are shared by multiple encoders
(DP and HDMI for pre-DDI platforms). Previously we would only
handle such pins via ->hpd_pulse(), but now we queue up the
hotplug work for the HDMI encoder directly. Worse yet, we now
count each hpd twice and this increment the hpd storm count
twice as fast. This can lead to spurious storms being detected.
Go back to the old way of doing things, ie. delegate to
->hpd_pulse() for any pin which has an encoder with that hook
implemented. I don't really like the idea of adding irq_port[]
back so let's loop through the encoders first to check if we
have an encoder with ->hpd_pulse() for the pin, and then go
through all the pins and decided on the correct course of action
based on the earlier findings.
I have occasionally toyed with the idea of unifying the pre-DDI
HDMI and DP encoders into a single encoder as well. Besides the
hotplug processing it would have the other benefit of preventing
userspace from trying to enable both encoders at the same time.
That is simply illegal as they share the same clock/data pins.
We have some testcases that will attempt that and thus fail on
many older machines. But for now let's stick to fixing just the
hotplug code.
Cc: stable@vger.kernel.org # 4.19+
Cc: Lyude Paul <lyude@redhat.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Fixes: b6ca3eee18 ("drm/i915: Nuke dev_priv->irq_port[]")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181108200424.28371-1-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Use the proper helper instead of manually iterating the scatterlist,
which is broken in the presence of chained S/G lists.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Instead create add to the icmd into struct mtip_cmd which can be unioned
with the scatterlist used for the normal I/O path.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Merging this function into the only callers makes the code flow easier.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There isn't much need for this helper - we can just calculate the offset
for the command header once late in the submission path and fill out
the ctba and ctbau fields there.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Factor out a new is_stopped helper that matches the existing
is_se_active helper, and merge the trivial amount of remaining code
into the only caller. This also allows better error handling by
returning a BLK_STS_* directly instead of explicitly calling
blk_mq_end_request, and moving blk_mq_start_request closer to the
actual issue to hardware.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We have all arguments at hand in mtip_hw_submit_io, so keep the
rq to sg mapping close to the dma_map_sg call.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently the size of hypercall buffers allocated via
/dev/xen/hypercall is limited to a default of 64 memory pages. For live
migration of guests this might be too small as the page dirty bitmask
needs to be sized according to the size of the guest. This means
migrating a 8GB sized guest is already exhausting the default buffer
size for the dirty bitmap.
There is no sensible way to set a sane limit, so just remove it
completely. The device node's usage is limited to root anyway, so there
is no additional DOS scenario added by allowing unlimited buffers.
While at it make the error path for the -ENOMEM case a little bit
cleaner by setting n_pages to the number of successfully allocated
pages instead of the target size.
Fixes: c51b3c639e ("xen: add new hypercall buffer mapping device")
Cc: <stable@vger.kernel.org> #4.18
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
We would like to consolidate Intel pure GPIO drivers, including PMICs and
some old x86 platforms, in one tree which is maintained by Intel.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Commit a856531951 ("xen: make xen_qlock_wait() nestable")
introduced a regression for Xen guests running fully virtualized
(HVM or PVH mode). The Xen hypervisor wouldn't return from the poll
hypercall with interrupts disabled in case of an interrupt (for PV
guests it does).
So instead of disabling interrupts in xen_qlock_wait() use a nesting
counter to avoid calling xen_clear_irq_pending() in case
xen_qlock_wait() is nested.
Fixes: a856531951 ("xen: make xen_qlock_wait() nestable")
Cc: stable@vger.kernel.org
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Juergen Gross <jgross@suse.com>
drvdata is actually sun8i_codec, not snd_soc_card, so it crashes
when calling snd_soc_card_get_drvdata().
Drop card and scodec vars anyway since we don't need to
disable/unprepare clocks - it's already done by calling
runtime_suspend()
Drop clk_disable_unprepare() calls for the same reason.
Fixes: 36c684936f ("ASoC: Add sun8i digital audio codec")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ath.git patches for 4.21. Major changes:
ath10k
* add support for WCN3990 firmware crash recovery
* add firmware memory dump support for QCA4019
wil6210
* add firmware error recovery while in AP mode
ath9k
* remove experimental notice from dynack feature
The current sx8 code spends a lot of effort dealing with the fact that
tags are per-host, but there might be multiple queues. Now that the
driver has been converted to blk-mq it can take care of the blk-mq
tag_set concept that has been designed just for that.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Make the disk/queue alloc and free helpers per-port by moving the
trivial loops into the callers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In async IO blocking case the additional reference to the io is taken for
it to survive fuse_aio_complete(). In non blocking case this additional
reference is not needed, however we still reference io to figure out
whether to wait for completion or not. This is wrong and will lead to
use-after-free. Fix it by storing blocking information in separate
variable.
This was spotted by KASAN when running generic/208 fstest.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Reported-by: Zorro Lang <zlang@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: 744742d692 ("fuse: Add reference counting for fuse_io_priv")
Cc: <stable@vger.kernel.org> # v4.6
In current fuse_drop_waiting() implementation it's possible that
fuse_wait_aborted() will not be woken up in the unlikely case that
fuse_abort_conn() + fuse_wait_aborted() runs in between checking
fc->connected and calling atomic_dec(&fc->num_waiting).
Do the atomic_dec_and_test() unconditionally, which also provides the
necessary barrier against reordering with the fc->connected check.
The explicit smp_mb() in fuse_wait_aborted() is not actually needed, since
the spin_unlock() in fuse_abort_conn() provides the necessary RELEASE
barrier after resetting fc->connected. However, this is not a performance
sensitive path, and adding the explicit barrier makes it easier to
document.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: b8f95e5d13 ("fuse: umount should wait for all requests")
Cc: <stable@vger.kernel.org> #v4.19
fuse_request_send_notify_reply() may fail if the connection was reset for
some reason (e.g. fs was unmounted). Don't leak request reference in this
case. Besides leaking memory, this resulted in fc->num_waiting not being
decremented and hence fuse_wait_aborted() left in a hanging and unkillable
state.
Fixes: 2d45ba381a ("fuse: add retrieve request")
Fixes: b8f95e5d13 ("fuse: umount should wait for all requests")
Reported-and-tested-by: syzbot+6339eda9cb4ebbc4c37b@syzkaller.appspotmail.com
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Cc: <stable@vger.kernel.org> #v2.6.36
For the YUV conversion to work properly, ->x_scaling[1] should never
be set to VC4_SCALING_NONE, but vc4_get_scaling_mode() might return
VC4_SCALING_NONE if the horizontal scaling ratio exactly matches the
horizontal subsampling factor. Add a test to turn VC4_SCALING_NONE
into VC4_SCALING_PPF when that happens.
The old ->x_scaling[0] adjustment is dropped as I couldn't find any
mention to this constraint in the spec and it's proven to be
unnecessary (I tested various multi-planar YUV formats with scaling
disabled, and all of them worked fine without this adjustment).
Fixes: fc04023faf ("drm/vc4: Add support for YUV planes.")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20181109102633.32603-1-boris.brezillon@bootlin.com
We shouldn't consider an encoder inactive if it doesn't have a CRTC
linked, but has virtual MST encoders with a crtc linked. Fix this.
Also we should not sanitize the mapping for MST encoders, as it's always
their primary encoder (which could be even in SST mode) whose active
state determines if we need the clock being enabled for the
corresponding physical port. Fix this too.
This fixes at least an existing breakage where we incorrectly disabled
the clock for an active DP encoder when sanitizing its MST virtual
encoders. Not sure if there are BIOSes that enable an output in MST
mode, but our HW readout is mostly missing for it anyway, so just warn
for that case.
Fixes: 70332ac539 ("drm/i915/icl+: Sanitize port to PLL mapping")
Cc: Antonio Argenziano <antonio.argenziano@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reported-by: Antonio Argenziano <antonio.argenziano@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Tested-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107200836.10191-2-imre.deak@intel.com
Check for reserved register field values and conflicting
transcoder->port mappings (both MST and non-MST mappings or multiple SST
mappings).
This is also needed for the next patch to determine if a port is in MST
mode during sanitization after HW readout.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Antonio Argenziano <antonio.argenziano@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107200836.10191-1-imre.deak@intel.com
Obviously the created writesame bio has to be aligned with logical block
size, and use bio_allowed_max_sectors() to retrieve this number.
Cc: stable@vger.kernel.org
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Xiao Ni <xni@redhat.com>
Cc: Mariusz Dabrowski <mariusz.dabrowski@intel.com>
Fixes: b49a0871be ("block: remove split code in blkdev_issue_{discard,write_same}")
Tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Cleanup __blkdev_issue_discard() a bit:
- remove local variable of 'end_sect'
- remove code block of 'fail'
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Xiao Ni <xni@redhat.com>
Cc: Mariusz Dabrowski <mariusz.dabrowski@intel.com>
Tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Obviously the created discard bio has to be aligned with logical block size.
This patch introduces the helper of bio_allowed_max_sectors() for
this purpose.
Cc: stable@vger.kernel.org
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Xiao Ni <xni@redhat.com>
Cc: Mariusz Dabrowski <mariusz.dabrowski@intel.com>
Fixes: 744889b7cb ("block: don't deal with discard limit in blkdev_issue_discard()")
Fixes: a22c4d7e34 ("block: re-add discard_granularity and alignment checks")
Reported-by: Rui Salvaterra <rsalvaterra@gmail.com>
Tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This reverts commit 2acf70ade7.
The commit never really fixed the intended issue and caused all
kinds of other issues, including a use before initialization.
Suggested-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Whenever we update ns_head info, we need to make sure it is still
compatible with all underlying backing devices because although nvme
multipath doesn't have any explicit use of these limits, other devices
can still be stacked on top of it which may rely on the underlying limits.
Start with unlimited stacking limits, and every info update iterate over
siblings and adjust queue limits.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Even without CONFIG_P2PDMA this results in a error print:
nvmet: no peer-to-peer memory is available that's supported by rxe0 and /dev/nullb0
Fixes: c6925093d0 ("nvmet: Optionally use PCI P2P memory")
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
PCM OSS layer may allocate a few temporary buffers, one for the core
read/write and another for the conversions via plugins. Currently
both are allocated via vmalloc(). But as the allocation size is
equivalent with the PCM period size, the required size might be quite
small, depending on the application.
This patch replaces these vmalloc() calls with kvzalloc() for covering
small period sizes better. Also, we use "z"-alloc variant here for
addressing the possible uninitialized access reported by syzkaller.
Reported-by: syzbot+1cb36954e127c98dd037@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds a device tree platform driver for Cadence UFS Host
Controller. It can be enabled with SCSI_UFS_CDNS_PLATFORM Kconfig option.
Signed-off-by: Jan Kotas <jank@cadence.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds a DT binding documentation for Cadence UFS Host Controller.
Signed-off-by: Jan Kotas <jank@cadence.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
UFS host supplies the reference clock to UFS device and UFS device
specification allows host to provide one of the 4 frequencies (19.2 MHz, 26
MHz, 38.4 MHz, 52 MHz) for reference clock. Host should set the device
reference clock frequency setting in the device based on what frequency it
is supplying to UFS device.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Sayali Lokhande <sayalil@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While ptr and port both point to the uart_port structure, the former is
the untyped pointer cookie passed to interrupt handlers.
Use the correctly typed port variable instead, to improve type-safety.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With Androidx86 8.1, wificond returns "failed to get
nl80211_sta_info_tx_failed" and wificondControl returns "Invalid signal
poll result from wificond". The fix is to OR sinfo->filled with
BIT_ULL(NL80211_STA_INFO_TX_FAILED).
This missing bit is apparently not needed with NetworkManager, but it
does no harm in that case.
Reported-and-Tested-by: youling257 <youling257@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: youling257 <youling257@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Passing string ch_data_type[i].name as the format specifier is
potentially hazardous because it could (although very unlikely to)
have a format specifier embedded in it causing issues when parsing
the non-existent arguments to these. Follow best practice by using
the "%s" format string for the string.
Cleans up clang warning:
format string is not a string literal (potentially insecure) [-Wformat-security]
Fixes: e7f2b70fd3 ("staging: most: replace multiple if..else with table lookup")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>