Similar to commit 8f42cb7f64 ("ARM: dts: omap4: Add l4 interconnect
hierarchy and ti-sysc data"), let's add proper interconnect hierarchy
for l4 interconnect instances with the related ti-sysc interconnect
module data as in Documentation/devicetree/bindings/bus/ti-sysc.txt.
Using ti-sysc driver binding allows us to start dropping legacy platform
data in arch/arm/mach-omap2/omap*hwmod*data.c files later on in favor of
ti-sysc dts data.
This data is generated based on platform data from a booted system
and the interconnect acces protection registers for ranges. To avoid
regressions, we initially validate the device tree provided data
against the existing platform data on boot.
Note that we cannot yet include this file from the SoC dtsi file until
the child devices are moved to their proper locations in the
interconnect hierarchy in the following patch. Otherwise we would have
the each module probed twice.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With l4 interconnect hierarchy and ti-sysc interconnect target module
data in place, we can simply move all the related child devices to
their proper location and enable probing using ti-sysc.
In general the first child device address range starts at range 0
from the ti-sysc interconnect target so the move involves adjusting
the child device reg properties for that.
In case of any regressions, problem devices can be reverted to probe
with legacy platform data as needed by moving them back and removing
the related interconnect target module node.
Note that we are not yet moving dss or wkup_m3, those will be moved
later after some related driver changes.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Similar to commit 8f42cb7f64 ("ARM: dts: omap4: Add l4 interconnect
hierarchy and ti-sysc data"), let's add proper interconnect hierarchy
for l4 interconnect instances with the related ti-sysc interconnect
module data as in Documentation/devicetree/bindings/bus/ti-sysc.txt.
Using ti-sysc driver binding allows us to start dropping legacy platform
data in arch/arm/mach-omap2/omap*hwmod*data.c files later on in favor of
ti-sysc dts data.
This data is generated based on platform data from a booted system
and the interconnect acces protection registers for ranges. To avoid
regressions, we initially validate the device tree provided data
against the existing platform data on boot.
Note that we cannot yet include this file from the SoC dtsi file until
the child devices are moved to their proper locations in the
interconnect hierarchy in the following patch. Otherwise we would have
the each module probed twice.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With l4 interconnect hierarchy and ti-sysc interconnect target module
data in place, we can simply move all the related child devices to
their proper location and enable probing using ti-sysc.
In general the first child device address range starts at range 0
from the ti-sysc interconnect target so the move involves adjusting
the child device reg properties for that.
In case of any regressions, problem devices can be reverted to probe
with legacy platform data as needed by moving them back and removing
the related interconnect target module node.
Note that we are not yet moving dss or wkup_m3, those will be moved
later after some related driver changes.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Similar to commit 8f42cb7f64 ("ARM: dts: omap4: Add l4 interconnect
hierarchy and ti-sysc data"), let's add proper interconnect hierarchy
for l4 interconnect instances with the related ti-sysc interconnect
module data as in Documentation/devicetree/bindings/bus/ti-sysc.txt.
Using ti-sysc driver binding allows us to start dropping legacy platform
data in arch/arm/mach-omap2/omap*hwmod*data.c files later on in favor of
ti-sysc dts data.
This data is generated based on platform data from a booted system
and the interconnect acces protection registers for ranges. To avoid
regressions, we initially validate the device tree provided data
against the existing platform data on boot.
Note that we cannot yet include this file from the SoC dtsi file until
the child devices are moved to their proper locations in the
interconnect hierarchy in the following patch. Otherwise we would have
the each module probed twice.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert DRA7xx to use the new clockdomain based layout. Previously the
clkctrl split was based on CM isntance boundaries. The new layout
helps with introducing the interconnect driver instances.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert AM43xx to use the new clockdomain based layout. Previously the
clkctrl split was based on CM isntance boundaries. The new layout
helps with introducing the interconnect driver instances.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert AM33xx to use the new clockdomain based layout. Previously the
clkctrl split was based on CM instance boundaries. The new layout
helps with introducing the interconnect driver instances.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This series gets rid of the SYSC_QUIRK_RESOURCE_PROVIDER to make device
detection happen mostly only if #define DEBUG is set. Few core devices still
need to be detected to set legacy quirks.
We also add support for booting am335x, am437x and dra7 SoCs with L4 devices
defined in device tree instead of legacy platform data.
And finally we simplify suspend with just SET_NOIRQ_SYSTEM_SLEEP_PM_OPS
and dropping the custom functions that were attempting to work around
issues that really turned out to be child device driver related issues.
Apologies for a late pull request, debugging the suspend issues took a while
and I did not want to send these changes until that got sorted out.
-----BEGIN PGP SIGNATURE-----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=f9xh
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.20/ti-sysc-take2-signed' into omap-for-v4.21/dt-ti-sysc
TI sysc driver changes for v4.20 merge window
This series gets rid of the SYSC_QUIRK_RESOURCE_PROVIDER to make device
detection happen mostly only if #define DEBUG is set. Few core devices still
need to be detected to set legacy quirks.
We also add support for booting am335x, am437x and dra7 SoCs with L4 devices
defined in device tree instead of legacy platform data.
And finally we simplify suspend with just SET_NOIRQ_SYSTEM_SLEEP_PM_OPS
and dropping the custom functions that were attempting to work around
issues that really turned out to be child device driver related issues.
Apologies for a late pull request, debugging the suspend issues took a while
and I did not want to send these changes until that got sorted out.
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2018-10-18
1) Remove an unnecessary dev->tstats check in xfrmi_get_stats64.
From Li RongQing.
2) We currently do a sizeof(element) instead of a sizeof(array)
check when initializing the ovec array of the secpath.
Currently this array can have only one element, so code is
OK but error-prone. Change this to do a sizeof(array)
check so that we can add more elements in future.
From Li RongQing.
3) Improve xfrm IPv6 address hashing by using the complete IPv6
addresses for a hash. From Michal Kubecek.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2018-10-18
1) Free the xfrm interface gro_cells when deleting the
interface, otherwise we leak it. From Li RongQing.
2) net/core/flow.c does not exist anymore, so remove it
from the MAINTAINERS file.
3) Fix a slab-out-of-bounds in _decode_session6.
From Alexei Starovoitov.
4) Fix RCU protection when policies inserted into
thei bydst lists. From Florian Westphal.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The PCI controller in the Marvell Armada 3720 does not implement a
software-accessible root port PCI bridge configuration space. This
causes a number of problems when using PCIe switches or when the Max
Payload size needs to be aligned between the root complex and the
endpoint.
Implementing an emulated root PCI bridge, like is already done in the
pci-mvebu driver for older Marvell platforms allows to solve those
issues, and also to support features such as ASR, PME, VC, HP.
Signed-off-by: Zachary Zhang <zhangzg@marvell.com>
[Thomas: convert to the common emulated PCI bridge logic.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Convert the pci-mvebu driver to use the pci-bridge-emul logic, that
helps emulating a root port PCI bridge configuration space.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Commit dc0352ab0b ("PCI: mvebu: Add PCI Express root complex
capability block") added support for emulating the PCI Express
capability block. As part of this, the pcie_sltcap, pcie_devctl and
pcie_rtctl fields were added to the mvebu_sw_pci_bridge structure, and
used when reading the corresponding PCI Express capability block
registers.
However, those structure members are never set to any value other than
zero. This makes them unneeded because:
- pcie_devctl is used to OR *value, so with pcie_devctl always zero,
it has no effect.
- for pcie_sltcap and pcie_rtstl, the mvebu_sw_pci_bridge_read()
function always returns 0 for registers that are not explicitly
handled.
In preparation for reworking the PCI bridge emulation logic in
pci-mvebu, let's simplify the code by dropping those structure
members.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Some PCI host controllers do not expose a configuration space for the
root port PCI bridge. Due to this, the Marvell Armada 370/38x/XP PCI
controller driver (pci-mvebu) emulates a root port PCI bridge
configuration space, and uses that to (among other things) dynamically
create the memory windows that correspond to the PCI MEM and I/O
regions.
Since we now need to add a very similar logic for the Marvell Armada
37xx PCI controller driver (pci-aardvark), instead of duplicating the
code, we create in this commit a common logic called pci-bridge-emul.
The idea of this logic is to emulate a root port PCI bridge
configuration space by providing configuration space read/write
operations, and faking behind the scenes the configuration space of a
PCI bridge. A PCI host controller driver simply has to call
pci_bridge_emul_conf_read() and pci_bridge_emul_conf_write() to
read/write the configuration space of the bridge.
By default, the PCI bridge configuration space is simply emulated by a
chunk of memory, but the PCI host controller can override the behavior
of the read and write operations on a per-register basis to do
additional actions if needed. We take care of complying with the
behavior of the PCI configuration space registers in terms of bits
that are read-write, read-only, reserved and write-1-to-clear.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Previously, we allow multiple nodes can resync device, but we
had changed it to only support one node can do resync at one
time, but suspend_info is still used.
Now, let's remove the structure and use suspend_lo/hi to record
the range.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
We need to continue the reshaping if it was interrupted in
original node. So original node should call resync_bitmap
in case reshaping is aborted.
Then BITMAP_NEEDS_SYNC message is broadcasted to other nodes,
node which continues the reshaping should restart reshape from
mddev->reshape_position instead of from the first beginning.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
When reshape is happening in one node, other nodes could receive
lots of RESYNCING messages, so md_bitmap_sync_with_cluster is called.
Since the resyncing window is typically small in these RESYNCING
messages, so WARN is always triggered, so we should not call the
func when reshape is happening.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
remove_and_add_spares is not needed if reshape is
happening in another node, because raid10_add_disk
called inside raid10_start_reshape would handle the
role changes of disk. Plus, remove_and_add_spares
can't deal with the role change due to reshape.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
We need to change the capacity in all nodes after one node
finishs reshape. And as we did before, we can't change the
capacity directly in md_do_sync, instead, the capacity should
be only changed in update_size or received CHANGE_CAPACITY
msg.
So master node calls update_size after completes reshape in
md_reap_sync_thread, but we need to skip ops->update_size if
MD_CLOSING is set since reshaping could not be finish.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Since the resync region from suspend_info means one node
is reshaping this area, so the position of reshape_progress
should be included in the area.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Replace the kvmalloc_array() with i915_gem_object_get_dma_address() when
populating rotated vmas. One random access mechanism ought to be enough
for everyone?
To calculate the size of the radix tree I think we can do
something like this (assuming 64bit pointers):
num_pages = obj_size / 4096
tree_height = ceil(log64(num_pages))
num_nodes = sum(64^n, n, 0, tree_height-1)
tree_size = num_nodes * 576
If we compare that with the object size we should get a relative
overhead of around .2% to 1% for reasonable sized objects,
which framebuffers tend to be.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181016150413.11577-1-ville.syrjala@linux.intel.com
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
For clustered raid10 scenario, we need to let all the nodes
know about that a new disk is added to the array, and the
reshape caused by add new member just need to be happened in
one node, but other nodes should know about the change.
Since reshape means read data from somewhere (which is already
used by array) and write data to unused region. Obviously, it
is awful if one node is reading data from address while another
node is writing to the same address. Considering we have
implemented suspend writes in the resyncing area, so we can
just broadcast the reading address to other nodes to avoid the
trouble.
For master node, it would call reshape_request then update sb
during the reshape period. To avoid above trouble, we call
resync_info_update to send RESYNC message in reshape_request.
Then from slave node's view, it receives two type messages:
1. RESYNCING message
Slave node add the address (where master node reading data from)
to suspend list.
2. METADATA_UPDATED message
Once slave nodes know the reshaping is started in master node,
it is time to update reshape position and call start_reshape to
follow master node's step. After reshape is done, only reshape
position is need to be updated, so the majority task of reshaping
is happened on the master node.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
To support add disk under grow mode, we need to resize
all the bitmaps of each node before reshape, so that we
can ensure all nodes have the same view of the bitmap of
the clustered raid.
So after the master node resized the bitmap, it broadcast
a message to other slave nodes, and it checks the size of
each bitmap are same or not by compare pages. We can only
continue the reshaping after all nodes update the bitmap
to the same size (by checking the pages), otherwise revert
bitmap size to previous value.
The resize_bitmaps interface and BITMAP_RESIZE message are
introduced in md-cluster.c for the purpose.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
The VMD removal path calls pci_stop_root_busi(), which tears down the pcie
tree, including detaching all of the attached drivers. During driver
detachment, devices may use pci_release_region() to release resources.
This path relies on the resource being accessible in resource tree.
By detaching the child domain from the parent resource domain prior to
stopping the bus, we are preventing the list traversal from finding the
resource to be freed. If we instead detach the resource after stopping
the bus, we will have properly freed the resource and detaching is
simply accounting at that point.
Without this order, the resource is never freed and is orphaned on VMD
removal, leading to a warning:
[ 181.940162] Trying to free nonexistent resource <e5a10000-e5a13fff>
Fixes: 2c2c5c5cd2 ("x86/PCI: VMD: Attach VMD resources to parent domain's resource tree")
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Add a shortcut for dm_device_name(dm_table_get_md(t)).
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
In copy_params(), the struct 'dm_ioctl' is first copied from the user
space buffer 'user' to 'param_kernel' and the field 'data_size' is
checked against 'minimum_data_size' (size of 'struct dm_ioctl' payload
up to its 'data' member). If the check fails, an error code EINVAL will be
returned. Otherwise, param_kernel->data_size is used to do a second copy,
which copies from the same user-space buffer to 'dmi'. After the second
copy, only 'dmi->data_size' is checked against 'param_kernel->data_size'.
Given that the buffer 'user' resides in the user space, a malicious
user-space process can race to change the content in the buffer between
the two copies. This way, the attacker can inject inconsistent data
into 'dmi' (versus previously validated 'param_kernel').
Fix redundant copying of 'minimum_data_size' from user-space buffer by
using the first copy stored in 'param_kernel'. Also remove the
'data_size' check after the second copy because it is now unnecessary.
Cc: stable@vger.kernel.org
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Use single exit point to drop rpm wakeref in case of an error.
Fixes: 9d3eb2c33f ("drm/i915: Hold rpm wakeref for debugfs/i915_drop_caches_set")
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20181018092025.24076-1-joonas.lahtinen@linux.intel.com
Using the sh_entsize for both values isn't correct. It happens to be
correct on x86...
For both 32-bit and 64-bit sparc, there are four PLT entries in the PLT
section.
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexis Berlemont <alexis.berlemont@gmail.com>
Cc: David Tolnay <dtolnay@gmail.com>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Hemant Kumar <hemant@linux.vnet.ibm.com>
Cc: Li Bin <huawei.libin@huawei.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Milian Wolff <milian.wolff@kdab.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Cc: zhangmengting@huawei.com
Fixes: b2f7605076 ("perf symbols: Fix plt entry calculation for ARM and AARCH64")
Link: http://lkml.kernel.org/r/20181017.120859.2268840244308635255.davem@davemloft.net
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Back when I added -Werror in commit ba55bd7436 ("powerpc: Add
configurable -Werror for arch/powerpc") I did it by adding it to most
of the arch Makefiles.
At the time we excluded math-emu, because apparently it didn't build
cleanly. But that seems to have been fixed somewhere in the interim.
So move the -Werror addition to the top-level of the arch, this saves
us from repeating it in every Makefile and means we won't forget to
add it to any new sub-dirs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This is a nice cleanup, arch/powerpc/Makefile is long and messy so
moving this out helps a little.
It also allows us to do:
$ make arch/powerpc
Which can be helpful if you just want to compile test some changes to
arch code and not link everything.
Finally it also gives us a single place to do subdir-cc-flags
assignments which affect the whole of arch/powerpc, which we will do
in a future patch.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There's some antiquated debug output that's trying
to do a hand-made hexdump and turning into horrible
1-byte-per-line output these days.
Use print_hex_dump() instead
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
do_exit() already includes a test to panic() is in_interrupt()
This patch removes powerpc one which is redundant.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When creating the boot-time FDT from an actual Open Firmware live
tree, let's generate "phandle" properties for the phandles instead
of the old deprecated "linux,phandle".
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Unsplit warning printf()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
prom_init.c must not modify the kernel image outside
of the .bss.prominit section. Thus make sure that
prom_init.o doesn't have anything in any of these:
.data
.bss
.init.data
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This makes __prombss its own section, and for now store
it in .bss.
This will give us the ability later to store it elsewhere
and/or free it after boot (it's about 8KB).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As they are no longer used past the end of prom_init
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Make the existing initialized definition constant and copy
it to a __prombss copy
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Initialize it dynamically instead of statically
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>